Femoral stem subsidence in cementless total hip arthroplasty: a retrospective single-centre study.

PURPOSE AND HYPOTHESIS: Subsidence is a known reason for early failure of total hip arthroplasty (THA). In particular, cementless THA might be vulnerable to migration. The present study analysed femoral stem subsidence after primary cementless THA. Prosthetic and anatomical risk factors for early femoral stem subsidence were evaluated. METHODS: Two hundred thirty-one consecutive patients who underwent primary cementless THA in a single centre were retrospectively analysed. Post-operative results were evaluated in consideration of prosthetic and anatomical properties in correlation with subsidence on standing pelvic anteroposterior radiographs. Stem type and design, demographic data, BMI, canal flare index (CFI) and canal fill ratio (CFR) were evaluated. RESULTS: The subsidence rate was significantly higher in collarless femoral stems [3.1 mm (SD 2.8 mm) vs. 1.9 mm (SD 1.5 mm); p = 0.013] while the anatomical type of the proximal femur as described by the canal flare index did not influenced subsidence (p = 0.050). Also, the canal fill ratio showed no significant correlation with subsidence at any level. CONCLUSIONS: In the present study, stem subsidence was significantly higher in the collarless group compared to collared stems. No anatomical parameter (CFI and CFR) could be identified as risk factor for subsidence. Neither age nor BMI influenced subsidence in this cohort. Still, subgroup analysis indicated a sex-dependent role of BMI. Prospective studies of large cohorts should address the problem of subsidence in the future. LEVEL OF EVIDENCE: Retrospective therapeutic study, Level IV.

Fixation pattern of conical and cylindrical modular revision hip stems in different size bone defects.

PURPOSE: Femoral defects often make it difficult to achieve sufficient fixation of the stem during revision surgery. No clinical studies comparing modular stems are available and differentiated recommendations are rare. The aim of this study was to compare the fixation of different revision stems in an experimental and standardised manner. METHODS: Segmental AAOS type I and III defects were reproduced in four femur pairs and two modular stems of different shape (cylindrical and conical) were implanted. Interfacial stem-bone movements were measured under axial torque application to analyze the stem fixation depending on defect extension. RESULTS: Both stems showed adequate fixation in AAOS type I defect. The defect extension significantly reduced the fixation of both implants. The fixation pattern changed significantly for the cylindrical-shaped stem but was maintained for the conical-shaped stem. CONCLUSIONS: Shape as well as the extension of femoral defect have an impact on primary fixation. A type I defect seems to be bridgeable for both stems albeit in a different way. In contrast, stem-demanding activities during the healing phase have to be avoided for the conical-shaped stem in a type III defect, whereas the cylindrical-shaped stem has already ceased to be sufficiently stable in this case.

Strut grafts in revision hip arthroplasty faced with femoral bone defects: an experimental analysis.

PURPOSE: In total hip arthroplasty fixation of revision stems can be demanding due to femoral bone loss. Strut grafts are often used for bone augmentation and stabilization of the newly inserted prosthesis. The aim of this study was to assess the effect of strut grafts on primary stability under various stem fixation conditions. METHODS: Two different revision stems (cylindrical and conical shape) were implanted into synthetic femora. Following a semicircular transfemoral osteotomy, three deficient femoral bearings were simulated (bony lid reattached with cable wires; weakened lid reattached with cable wires; strut grafts placed to the weakened lid with cable wires). Relative micro-movements were measured between prostheses and bones due to an axial moment applied to the stems. RESULTS: Relative movements correlated to the stem shape. The cylindrical stem showed higher movements increasing significantly with a weakened bony lid and portrayed a slight decrease of movements with strut graft application. No unequivocal influence of the weakened lid could be detected for the conical implant. Strut graft application did not show an additional stabilizing effect. CONCLUSIONS: The primary stability of the cylindrical fixation concept decreases with impaired fixation conditions of the femur. A clear restabilizing effect with strut grafts could not be proven. A decrease of primary stability due to the impaired bone could not be observed for the conical stem shape. Additionally, strut grafts do not enhance fixation for this stem shape. We conclude that surgeons should not rely on a stabilizing effect of strut grafts in revision hip surgery.

Short-keeled cemented tibial components show an increased risk for aseptic loosening.

BACKGROUND: The choice of implant design plays an important role for primary fixation of a TKA. Short-keeled tibial components allow implantation through a smaller approach with less femorotibial subluxation. QUESTIONS/PURPOSES: The purpose of this study was to detect early implant failure resulting from aseptic loosening after cemented short-keeled and standard tibial baseplate implantation. METHODS: Between 2008 and 2010, a group of 160 consecutive patients (with 80 standard and with 80 short-keeled tibial trays) received cemented TKAs. At 1-year followup, patients were examined clinically and radiographs were analyzed regarding aspects of radiolucency. The components were divided into five zones on each radiographic view and the measurements of the 10 zones were added. RESULTS: The mean sum of radiolucencies was increased significantly with the short-keeled baseplates. In the current study, short-keeled tibial trays revealed a revision rate of 6.3% after 1-year followup. In contrast, none of the standard tibial baseplates were revised. CONCLUSIONS: The implantation of cemented, short-keeled tibial components is linked to an increased rate of early loosening. Therefore, the indication for cemented, short-keeled component implantation should be reviewed. LEVEL OF EVIDENCE: Level III, therapeutic study. See Guidelines for Authors for a complete description of levels of evidence.

Cementing techniques for hip resurfacing arthroplasty: in vitro study of pressure and temperature.

Cementing irregularities have been associated with femoral failures of resurfacing arthroplasties in retrieval studies. We used an in vitro model to measure pressure, temperatures, and cement penetration as a function of 6 different cementing techniques. Filling the component with cement can lead to overpenetration or increase the resistance to component seating with resultant polar cement mass. Both conditions result in high and long-lasting cement pressures, cement defects, as well as peak temperatures higher than 50°C. Manual application of cement provides complete penetration of the available fixation area with the lowest cement pressures, the smallest total cement mass, and a peak temperature of 36.0°C ± 4.1°C. Application of the principles elucidated by this study may reduce the risk of cement overpenetration and incomplete seating.

Influence of resting periods on polyethylene wear in a knee simulator study.

BACKGROUND: Knee wear simulator studies are performed to evaluate the wear behavior of implants. These wear studies simulate in vivo situations as closely as possible. Simulation of the human gait cycle is often carried out continuously according to international standards. However, implants are not loaded continuously in vivo, so it might be advisable to implement resting periods in which no motion occurs. MATERIAL/METHODS: In the present study the influence of resting periods on the wear behavior of a commercial implant was analyzed using a force-controlled AMTI knee simulator. RESULTS: The wear rates were 2.27+/-0.23 mg/10(6) cycles for a simulation with resting periods and 2.85+/-0.27 mg/10(6) cycles for a reference simulation without resting periods. There was no significant difference (p=0.22) in wear behavior between these two tests. CONCLUSIONS: The present study shows that continuous simulation without the implementation of resting periods is a valid approach for assessing the wear of knee implants.

The influence of age, bone quality and body mass index on periprosthetic femoral fractures: a biomechanical laboratory study.

BACKGROUND: A periprosthetic femoral fracture after total hip arthroplasty is a serious but uncommon complication, and therefore difficult to analyze clinically in scientifically and statistically valid study samples. With the aim of preventing these fractures the purpose of this study was to investigate potential risk factors associated with cementless hip arthroplasty in a standardized laboratory setup. Additionally, we aimed to clarify if the treatment with a cementless hip stem is fraught with higher risk of periprosthetic fracture for older patients compared to younger patients. MATERIAL/METHODS: A biomechanical setup was developed to provide analysis on sixteen femoral specimens of different age. A cementless hip stem was implanted into the specimens and loads - representing hip contact forces - were applied under standardized conditions until fracture occurred. The femurs were divided into two age groups (<70 and >or=77 years of age). RESULTS: The elderly specimens fractured at significantly lower maximum forces (<70: Fmax=5,308N; >or=77: Fmax=2,519N; p<0.01). Maximum fracture loads were found to correlate strongly with age (p=0.01), BMD (e.g. for the Ward's triangle: p<0.01) and BMI (p=0.04). CONCLUSIONS: In patients with advanced age treated with cementless hip stems the risk of suffering a periprosthetic fracture is significantly higher. It increases in patients with an age of 80 years or older, a Ward's triangle BMD below 0.500 g/cm2 and a BMI >33 kg/m2. Whereas one single factor must not be viewed as an exclusion criterion for a cementless hip stem treatment, cumulation of these factors should alert the orthopaedic surgeon.

Patient activity after total hip arthroplasty declines with advancing age.

Evaluation of patient activity is essential for clinical decision making before THA. To correlate age progression to patient activity after THA, we determined the number of walking cycles of 105 patients in different age groups by decades. Patients on average performed 6144 walking cycles per day (2.24 million cycles per year). Men were more active than women. The highest activity occurred in patients between 50 and 59 years of age, with a constant decrease in activity with advancing age. However, within age groups, we observed up to sixfold differences in the number of walking cycles per day. In addition to declining activity with advancing age, higher body mass index correlated with lower step counts. The high mean measured number of walking cycles, which were even higher than those reported for subjects without an arthroplasty, suggests patients benefit from THA. Female gender, advanced age, and obesity correlated with lower activity. Owing to the high intragroup variability of our results, preoperative evaluation of patient activity levels, individual patient factors, and patient demands, should be considered in clinical practice.

Ten different hip resurfacing systems: biomechanical analysis of design and material properties.

This study gives an overview of the main macro- and microstructural differences of ten commercially available total hip resurfacing implants. The heads and cups of resurfacing hip implants from ten different manufacturers were analysed. The components were measured in a coordinate measuring machine. The microstructure of the heads and cups was inspected by scanning electron microscopy. The mean radial clearance was 84.86 microm (range: 49.47-120.93 microm). The implants were classified into three groups (low, medium and high clearance). All implants showed a deviation of roundness of less than 10 microm. It was shown that all implants differ from each other and a final conclusion about the ideal design and material combination cannot be given based on biomechanical data. Widespread use of specific designs can only be recommended if clinical long-term follow-up studies are performed and analysed for each design.

Biochemical markers of bone turnover in aseptic loosening in hip arthroplasty.

The aim of this study was to determine the diagnostic value of systemic biochemical markers of bone turnover in aseptic loosening in hip arthroplasty, namely the urine levels of three bone resorption peptides - crosslinked n-telopeptides (NTX), c-telopeptides (CTX I) and deoxypyridinoline (DPD). We compared 52 patients with surgically proven component loosening with 52 patients without clinical or radiological signs of endoprosthetic loosening and 52 healthy individuals. All three markers were measured using commercially available enzyme-linked immunoassays. We found significantly increased levels of DPD in the loosening group (p < 0.05), but there was no significant difference between the loosening group and the two reference groups for the other two markers tested. Our data suggest that DPD can be used as an additional tool in the diagnosis of aseptic loosening in hip arthroplasty but CTX I and NTX have no predictive value in this context.

Metal release and corrosion effects of modular neck total hip arthroplasty.

Modular neck implants are an attractive treatment tool in total hip replacement. Concerns remain about the mechanical stability and metal ion release caused by the modular connection. Five different implant designs were investigated in an experimental set-up. In vivo conditions were simulated and the long-term titanium release was measured. Finally, the modular connections were inspected for corrosion processes and signs of fretting. No mechanical failure or excessive corrosion could be identified for the implants tested. The titanium releases measured were extremely low compared to in vivo and in vitro studies and were not in a critical range.

Do short-stemmed-prostheses induce periprosthetic fractures earlier than standard hip stems? A biomechanical ex-vivo study of two different stem designs.

INTRODUCTION: The causes of periprosthetic fractures of the femur due to the design of the prosthesis and the individual parameters of the patient are unexplored. By different anchorage techniques in cementless total hip arthroplasties, it is assumed that there are various load limits of the implant's bearing femur. MATERIALS AND METHODS: In the present study, we compared a standard hip stem (cementless Spotorno) and a short-stemmed design (Mayo) by an artificial reproduction of periprosthetic fractures in 20 femur specimens. RESULTS: The measured fracture loads showed an extensive range, with higher maximum loads in the standard stem group. The bone mineral density and the subsiding pattern of the standard stems showed a significant correlation to the incidence of the periprosthetic fractures. In the experimental setup, a slightly lower fracture resistance was shown for the short-stemmed prosthesis. Additionally, it was shown that donors with a higher body mass index had a significantly increased fracture risk. CONCLUSIONS: Short-stemmed prostheses, especially the Mayo hip, do not constitute a higher fracture risk. In general, an increased body mass index among patients with a cementless hip stem is associated with an increased fracture risk, particularly at high load values, i.e., resulting from a step during stumbling. Taking into account the ascertained results, the danger of provoking a femoral periprosthetic fracture can be reduced.

Chondrogenesis of mesenchymal stem cells in gel-like biomaterials in vitro and in vivo.

Gel-like carrier materials were introduced into cell therapy of cartilage lesions to improve chondrocyte retention and distribution in the defect. Mesenchymal stem cells (MSC) are now discussed as an alternative cell source for repair. We here asked whether distinct gel-like carriers can support chondrogenesis of MSC in vitro and lead to stable cartilage-like transplants in vivo. Chondrogenesis of MSC embedded in collagen type I gel, fibrin glue, Matrigel and PuraMatrix peptide hydrogel was assessed and gene expression analysis, proteoglycan content, and collagen synthesis were quantified. Differentiated constructs were transplanted subcutaneously into SCID mice. All carriers supported chondrogenesis in vitro, but displayed material-dependent differences on COL2A1 gene expression, total collagen synthesis and proteoglycan deposition. The undesired calcification and microossicle formation in ectopic transplants in vivo was consistently suppressed by Matrigel. In sum, gel-like biomaterials were suitable carriers for MSC and promoted chondrogenesis. Suppression of calcification by particular gel-like materials makes their use even more attractive for MSC-based tissue engineering approaches in cartilage repair.

Primary rotational stability of cylindrical and conical revision hip stems as a function of femoral bone defects: an in vitro comparison.

Bone stock losses in cementless femoral stem revisions compromise a stable fixation. The surgeon has to rely on his wealth of experience in deciding which stem shape to use. The aim of our study was to compare the primary rotational stability of cylindrical and conical revision hip stems subjected to femoral defects. Four current prostheses (two cylindrical, two conical) were implanted into four synthetic femora. Micro-motion was measured under torque application and femoral neck osteotomy and segmental AAOS Type I and III defects were simulated. The relative movements of all prostheses were significantly influenced by the extent of bone loss (p<0.01). Major differences were seen in fixation behavior (p<0.01). The main fixation area of conical stems is within the distal femoral isthmus, whereas cylindrical implants are dependent on proximal bone stock. In our study, cylindrical stems are advantageous for minor defects because they provide a proximal fixation. In cases of extensive substance loss, the conical implants showed lesser relative movements. These findings should be taken into account for clinical decisions.

Femoral cementing technique for hip resurfacing arthroplasty.

The resurgence of metal-metal bearings has renewed interest in hip resurfacing, but a paucity of information exists regarding femoral cementing technique. We developed a laboratory model in which 72 open-cell foam specimens were used to simulate bone. Analyses of two cement viscosities, two foam porosities, and six cementing techniques were performed: manual cement application only, manual application and filling of one quarter of the component with cement, filling of half of the component, manual application and half component filling, full component filling, and manual application and full component filling. For manual application, cement was pressurized into the foam by rolling the finger tips. For component filling, a defined quantity of cement was poured into the component before pressing it onto the foam. Specimens were cut into quarters, and cement penetration was quantified in seven areas: top, chamfer, wall, interior area, and proximal, medial, and distal stem. The manual technique showed a 3-mm thick, even cement penetration of the outer fixation surface (top = 26 +/- 0 mm(2), chamfer = 14.9 +/- 0.2 mm(2), wall = 55.6 +/- 5.2 mm(2)). None of the other techniques showed a significantly higher penetration in these areas. Large differences were found between all techniques at the medial stem (27.7 +/- 17.5 mm(2), p < 0.001) and the interior area (128.5 +/- 69.6 mm(2), p = 0.013). An increasing degree of penetration occurred from manual cement application to manual application and full component filling. Sixteen specimens showed incomplete seating, which occurred with all techniques except the manual technique. The manual technique consistently gave an approximately 3-mm thick even cement penetration over the outer fixation area. Pouring any cement into the shell resulted in variable degrees of deeper penetration and a risk of incomplete seating, which have been associated with bone necrosis and early fracture.

Failure of Polyethylene Inlays in Cementless Total Hip Arthroplasty: A Retrieval Analysis.

A retrieval analysis has been performed on 50 polyethylene inlays of cementless screw ring implants (Mecring, Mecron, Berlin, Germany) to investigate the failure mechanism of this specific open cup hip arthroplasty design that has shown a high clinical failure rate. Design-specific damage modes like rim creep, collar fatigue, and backside wear were assessed. Furthermore, the inlays were measured using a CMM to determine deformation. In 90% backside wear was observed and collar fatigue occurred in 68% of the cases. Rim creep was present in 38% of the polyethylene inlays. In 90% of the cases the cup opening diameter was 32.1 mm or less and 46% had a diameter less than 32 mm. It seems that creep and deformation of the polyethylene leads to a reduced diameter at the cup opening and consequently decreased clearance. To avoid this type of failure, polyethylene inlays should be supported at the back by the cup to reduce the risk of ongoing creep deformation.

The relationship between activity and ions in patients with metal-on-metal bearing hip prostheses.

BACKGROUND: Total hip replacements with metal-on-metal bearings are frequently implanted in young, active patients. The relationship between patient activity and cobalt and chromium ion levels has not been investigated, to our knowledge. METHODS: Seven patients with well-functioning metal-on-metal bearing hip prostheses and one control subject (no implants), all with normal renal function, were monitored during a two-week-long activity protocol. Lower-extremity activity was continuously assessed with use of a computerized, two-dimensional accelerometer. During the first week, the subjects were requested to limit physical activity. The subjects then completed an hour-long treadmill test followed by a week in which they were encouraged to be as physically active as practically possible. Serum levels of cobalt and chromium ions and urine levels of chromium were assessed at ten time-points during these two weeks. RESULTS: Regardless of activity, the serum ion levels for a given patient were essentially constant and no correlation was found between patient activity and serum levels of cobalt or chromium, or urine levels of chromium. A mean increase in activity of 28% during the week of high-intensity activity was associated with a mean decrease of 2.7% in the serum cobalt level and a mean increase of 2.0% in the serum chromium level. During the treadmill test, a mean increase in activity of 1621% was associated with a mean increase of 3.0% in the serum cobalt level and a mean increase of 0.8% in the serum chromium level. These results fall within the variability for the measurement accuracy of these tests. CONCLUSIONS: For these patients, serum cobalt and chromium ion levels were not acutely affected by patient activity. Periodic measurements of serum ion levels could be used to monitor the tribologic (lubrication, friction, and wear) performance of a metal-on-metal bearing without adjusting for patient activity. Additional research is needed into the kinetics of ion production, transport, and excretion.

The effects of lower-extremity total joint replacement for arthritis on obesity.

Total hip or knee replacement patients who are overweight or obese often consider their disabling joint disease a cause for their increased weight. This prospective study investigated weight change in 100 patients after successful total joint replacement to determine whether surgical treatment of hip or knee arthritis leads to weight reduction. Postoperatively, both hip and knee replacement patients gained weight, with no difference in weight gain between hip and knee replacement patients. Younger hip patients gained a significant amount of weight. Patients a with normal body mass index and obese patients did not lose weight, while overweight patients gained a significant amount of weight after surgery. These findings demonstrate successful treatment of lower-extremity arthritis does not lead to weight loss, and obesity should be treated as an independent disease that is not the result of inactivity from arthritis.

Short-term in vivo wear of cross-linked polyethylene.

BACKGROUND: Cross-linked polyethylene was developed to reduce volumetric wear in prosthetic joints. Hip simulator studies have shown promising results with regard to wear reduction. This study evaluated the short-term in vivo wear of a moderately cross-linked polyethylene. METHODS: Linear head penetration, as an assessment of in vivo polyethylene wear, was measured in two groups of patients after total hip replacement. Twenty-four hips received a conventional polyethylene insert and thirty-four, a cross-linked polyethylene liner; both inserts were manufactured by the same company. Linear and volumetric wear rates were measured on radiographs with use of a validated computer-assisted technique and were adjusted for patient-related factors. Patient activity was assessed by a computerized two-dimensional accelerometer worn on the ankle. RESULTS: Patients with a conventional polyethylene insert showed a mean linear wear rate of 0.13 mm per year and a mean volumetric wear rate of 87.6 mm(3) per year. The group with a cross-linked polyethylene liner showed a mean linear wear rate of 0.02 mm per year and a mean volumetric wear rate of 17.0 mm(3) per year. Wear in the group with cross-linked polyethylene was 81% lower than that in the group with conventional polyethylene (p < 0.00001). Accounting for differences in patient activity, the adjusted wear rates per million cycles for a patient weight of 70 kg were 53 mm(3) per million cycles for conventional polyethylene and 15 mm(3) per million cycles for cross-linked polyethylene, a 72% reduction (p = 0.0002). No factor, other than the type of polyethylene, was found to influence the difference in wear rates between the two groups. CONCLUSIONS: The results of this study are promising. The in vivo wear reduction with this cross-linked polyethylene is consistent with the predictions of hip simulator studies.

The biomechanical results of total hip resurfacing arthroplasty.

BACKGROUND: With the advent of more wear-resistant bearings, there is renewed interest in resurfacing total hip arthroplasty. However, there is a paucity of information on the biomechanical results of this type of arthroplasty compared with those of contemporary total hip arthroplasty. METHODS: Using standardized radiographs, we measured and compared the biomechanical parameters that affect the hip joint reactive forces in fifty hips that had a metal-metal surface replacement with those parameters in forty hips that had a contemporary cementless total hip replacement performed during the same time-period by the same surgeon. RESULTS: On the average, the arthritic hips that were treated with metal-metal surface replacement had had a more valgus preoperative neck-shaft angle and less horizontal femoral offset than the normal, contralateral hips (p = 0.0003). After both the metal-metal surface replacements and the cementless total hip replacements, the hip center of rotation was medialized by approximately 6 mm. Both procedures were associated with an average increase in limb length of approximately 3 or 4 mm. After the metal-metal surface replacements, the horizontal femoral offset was essentially equal to the preoperative value, but both values averaged about 8 mm less than those on the normal, contralateral side (p < 0.00001). In the hips with a conventional total hip replacement, the horizontal femoral offset increased an average of 9.5 mm compared with the preoperative value and was an average of 5 mm more than that for the normal, contralateral hip (p = 0.001). CONCLUSIONS: The biomechanical results of total hip resurfacing depend on the preoperative anatomy of the proximal part of the femur. Limb lengthening of 1 cm can be achieved, but horizontal femoral offset is essentially unchanged by hip resurfacing. Horizontal femoral offset can be increased reliably with a contemporary total hip replacement. Arthritic hips of limbs that are more than 1 cm shorter than the contralateral limb or that have a comparatively low horizontal femoral offset may be better served by a contemporary total hip replacement. These biomechanical limitations should be considered in the selection of hips for resurfacing. LEVEL OF EVIDENCE: Therapeutic study, Level III-1 (case-control study). See Instructions to Authors for a complete description of levels of evidence.