Characterization of microstructures and reaction mechanisms of Tröger's base polymers of intrinsic microporosity.

RATIONALE: Tröger's base polymers of intrinsic microporosity (PIMs) are receiving increasing attention for applications such as polymer molecular sieve membranes. Development of novel membrane materials requires microstructure analysis in order to overcome processing and applications challenges. This study aims to address these challenges and overcome some of the solubility/aggregation issues that hinder the analysis of these materials. METHODS: A combination of matrix-assisted laser desorption/ionization mass spectrometry and collision-induced dissociation was used to examine the reaction products of unfunctionalized Tröger's base PIMs. RESULTS: Enhanced data mining, using ultrahigh-resolution mass spectrometry and statistical analysis, yielded a wealth of information on the molecular mass, chemical connectivity, and end groups of species generated during synthesis. Modifications of interest include N-methyl, N-methanimine, N-formyl, and N-methylol end-capping moieties, as well as incomplete backbone methanodiazocine rings with missing bridging methylene linkages. Most importantly, a general fragmentation mechanism, supported by computational modeling, was developed to assist in the rapid identification of main-chain and end-group modifications in Tröger's base PIMs. CONCLUSIONS: Unfunctionalized Tröger's base polymers were selected as a model system, to thoroughly study their end-group modification chemistry. This model system could then be used to gain insights into complex hydroxy-functional PIM materials.

Single molecule observations of the adsorption sites of methyl isocyanide on Pt(111) by low-temperature scanning tunneling microscopy.

Scanning tunneling microscopy (STM) has been used to directly investigate the local structure of methyl isocyanide (CNCH3) adsorbed on Pt(111). At low coverages, CNCH3 is preferentially adsorbed at on-top sites, in agreement with earlier deductions based on vibrational spectroscopy. When dosed at low coverages at 50 K, the molecules tend to adsorb near other CNCH3 molecules with preferred distances of a and a, where a = 2.78 A is the lattice constant of Pt. Annealing the surface to 120 K, however, results in a more uniform separation of the molecules. At higher coverages, the CNCH3 molecules are observed to occupy both on-top and two-fold bridge sites. On the basis of STM image analysis, CNCH3 forms an ordered layer of (2 x 3) periodicity at 0.33 ML. Additional details on the structures of CNCH3 adsorbed at the on-top and two-fold bridge sites are provided by density functional theory (DFT) calculations. At a coverage that saturates the first layer (0.33 ML), the occupation ratio for the on-top and two-fold bridge bonded CNCH3 is 1:1, which is consistent with the results obtained from the combined use of experimental reflection absorption infrared spectroscopy (RAIRS) data and DFT calculations.

Surface chemistry of CN bond formation from carbon and nitrogen atoms on Pt(111).

The mechanism of CN bond formation from CH3 and NH3 fragments adsorbed on Pt(111) was investigated with reflection absorption infrared spectroscopy (RAIRS), temperature-programmed desorption (TPD), and X-ray photoelectron spectroscopy (XPS). The surface chemistry of carbon-nitrogen coupling is of fundamental importance to catalytic processes such as the industrial-scale synthesis of HCN from CH4 and NH3 over Pt. Since neither CH4 nor NH3 thermally dissociate on Pt(111) under ultrahigh vacuum (UHV) conditions, the relevant surface intermediates were generated through the thermal decomposition of CH3I and the electron-induced dissociation of NH3. The presence of surface CN is detected with TPD through HCN desorption as well as with RAIRS through the appearance of the vibrational features characteristic of the aminocarbyne (CNH2) species, which is formed upon hydrogenation of surface CN at 300 K. The RAIRS results show that HCN desorption at approximately 500 K is kinetically limited by the formation of the CN bond at this temperature. High coverages of Cads suppress CN formation, but the results are not influenced by the coadsorbed I atoms. Cyanide formation is also observed from the reaction of adsorbed N atoms and carbon produced from the dissociation of ethylene.

Reversible hydrogenation of surface N atoms to form NH on Pt(111).

The formation and dissociation chemistry of the NH species on Pt(111) was characterized with reflection absorption infrared spectroscopy and temperature programmed desorption. Irradiation of a chemisorbed bilayer of ammonia with a 100 eV electron beam at 85 K leads to a mixture of NH, N, and H on the surface. Annealing to temperatures in the range of 200-300 K leads to reaction of N and H to form additional NH. The NH species has an intense and narrow NH stretch peak at 3320 cm(-1), while no peak due to the PtNH bend is observed above 800 cm(-1). The NH species is stable up to a temperature of approximately 400 K. The surface N atoms produced from NH dissociation are readily hydrogenated back to NH by exposure of the surface to H2. However, NH cannot be further hydrogenated to generate adsorbed NH2 or to NH3 under the conditions used here. Exposure of the NH/Pt(111) surface to D2 at 380 K produces the ND species. Comparison with the results of density functional theory calculations based on small Pt clusters indicates that NH occupies three-fold hollow sites with the molecular axis perpendicular to the surface.

Identification and hydrogenation of C2 on Pt(111).

Reflection absorption infrared spectroscopy (RAIRS) and temperature-programmed desorption (TPD) were used to identify the molecular species formed upon the reaction of hydrogen with surface carbon that is deposited by exposing acetylene to a Pt(111) surface held at 750 K. At this temperature, the acetylene is completely dehydrogenated and all hydrogen is desorbed from the surface. Upon subsequent hydrogen exposure at 85 K followed by sequential annealing to higher temperatures, ethylidyne (CCH3), ethynyl (CCH), and methylidyne (CH) are formed. The observation of these species indicates that carbon atoms and C2 molecules exist as stable species on the surface over a wide range of temperatures. Through a combination of RAIRS intensities, hydrogen TPD peak areas, and Auger electron spectroscopy, quantitative estimates of the coverages of the various species were obtained. It was found that 79% of the acetylene-derived carbon was in the form of C2 molecules, with the remainder in the form of carbon atoms. Essentially all of the acetylene-derived carbon could be hydrogenated. In contrast, 85% of an equivalent coverage of carbon deposited by ethylene exposure at 750 K was found to be inert toward hydrogenation.

Formation of surface CN from the coupling of C and N atoms on Pt(111).

Reflection absorption infrared spectroscopy (RAIRS) and temperature-programmed desorption have been used to study the coupling of C and N atoms on Pt(111) to form surface CN. This reaction underlies the important synthesis of HCN from methane and ammonia over platinum catalysts. Since CH4 and NH3 do not thermally dissociate on Pt(111) under ultrahigh vacuum conditions, we used CH3I and electron bombardment of NH3 to generate reactive surface species. Surface CN is formed at a temperature of 500 K from surface Nads and Cads atoms. The presence of surface CN is detected by HCN desorption and through the reaction of hydrogen with CNads to form a surface >CNH2 (aminocarbyne) species, which has a characteristic RAIR spectrum.