Self-Driven Droplet Motions Below their Icing Points.

Liquid fluidity is a most key prerequisite for a broad range of technologies, from energy, fluid machineries, microfluidic devices, water, and oil transportation to bio-deliveries. While from thermodynamics, the liquid fluidity gradually diminishes as temperature decreases until completely solidified below icing points. Here, self-driven droplet motions are discovered and demonstrated occurring in icing environments and accelerating with both moving distances and droplet volumes. The self-driven motions, including self-depinning and continuous wriggling, require no surface pre-preparation or energy input but are triggered by the overpressure spontaneously established during icing and then continuously accelerated by capillary pulling of frosts. Such self-driven motions are generic to a broad class of liquid types, volumes, and numbers on various micro-nanostructured surfaces and can be facilely manipulated by introducing pressure gradients spontaneously or externally. The discovery and control of self-driven motions below icing points can greatly broaden liquid-related applications in icing environments.

1000 °C High-Temperature Wetting Behaviors of Molten Metals on Laser-Microstructured Metal Surfaces.

The melting of metals at high temperatures is common and important in many fields, e.g., metallurgy, refining, casting, welding, brazing, even newly developed batteries, and nuclear fusion, which is thus of great value in modern industrialization. However, the knowledge of the wetting behaviors of molten metals on various substrate surfaces remains insufficient, especially when the temperature is over 1000 °C and with microstructured metal substrate surfaces. Herein, we selected molten cerium (Ce) on a tantalum (Ta) substrate as an example and investigated in detail its wetting at temperatures up to 1000 °C by modulating the microstructures of the substrate surfaces via laser processing. We discovered that the wetting states of molten Ce on Ta surfaces at temperatures over 900 °C could be completely altered by modifying the laser-induced surface microstructures and the surface compositions. The molten Ce turned superlyophilic with its contact angle (CA) below 10° on the only laser-microstructured surfaces, while it exhibited lyophobicity with a CA of about 135° on the laser-microstructured plus oxidized ones, which demonstrated remarkably enhanced resistance against the melt with only tiny adhesion in this circumstance. In contrast, the CA of molten Ce on Ta substrate surfaces only changed from ∼25 to ∼95° after oxidization without laser microstructuring. We proved that modulating the substrate surface microstructures via laser together with oxidization was capable of efficiently controlling various molten metals' wetting behaviors even at very high temperatures. These findings not only enrich the understanding of molten metal high-temperature wettability but also enable a novel practical approach to control the wetting states for relevant applications.

Anisotropic Hemiwicking Behavior on Laser Structured Prismatic Microgrooves.

The wicking phenomenon, including wicking and hemiwicking, has attracted increasing attention for its critical importance to a wide range of engineering applications, such as thermal management, water harvesting, fuel cells, microfluidics, and biosciences. There exists a more urgent demand for anisotropic wicking behaviors since an increasing number of advanced applications are significantly complex. For example, special-shaped vapor chambers and heating atomizers in some electronic cigarettes need liquid replenishing with various velocities in different directions. Here, we report two-dimensional anisotropic hemiwicking behaviors with elliptical shapes on laser structured prismatic microgrooves. The prismatic microgrooves were fabricated via one-step femtosecond laser direct writing, and the anisotropic hemiwicking behaviors were observed when utilizing glycerol, glycol, and water as the test liquid. Specifically, the ratios of horizontal wicking distance in directions along short and long axes were tan 0°, tan 15°, tan 30°, and tan 45° for samples with cross-angles of 0°, 30°, 60°, and 90°, respectively. The vertical water wicking front displayed corresponding angles under the guidance of laser structured prismatic microgrooves. Theoretical analysis shows that the wicking distance is mainly dependent on the cross-angle θ and surface roughness, in which the wicking distance is proportional to cos(θ/2). Driven by the capillary pressure forming in the narrow microgrooves, the liquid initially filled the valleys of microgrooves and then surrounded and covered the prismatic ridges with laser-induced nanoparticles. The abundant nanoparticles increased the surface roughness, leading to the enhancement of wicking performance, which was further evidenced by the larger wicking speed of the sample with more nanoparticles. The mechanism of anisotropic hemiwicking behaviors revealed in this work paves the way for wicking control, and the proposed prismatic microgrooved surfaces with two-dimensional anisotropic hemiwicking performance and superhydrophilicity could serve in a broad range of applications, especially for the advanced thermal management with specific heat load configurations.

Morphology of the first zoeal stage of three deep-water pandalid shrimps, Heterocarpus abulbus Yang, Chan & Chu, 2010, H. hayashii Crosnier, 1988 and H. sibogae De Man, 1917 (Crustacea: Decapoda: Caridea).

The eggs of three deep-sea pandalid shrimps Heterocarpus abulbus, H. hayashii and H. sibogae are successfully hatched in the laboratory. The first zoeal stage of these shrimps are described, with those of H. abulbus and H. hayashii being reported for the first time. First zoeae of different Heterocarpus species can be distinguished by the spination at the anteroventral carapace, body size, rostral length and appendage setation. 

First stage zoeal morphology of four ghost crabs Ocypode ceratophthalmus (Pallas, 1772), O. cordimanus Latreille, 1818, O. sinensis Dai, Song & Yang, 1985 and O. stimpsoni Ortmann, 1897 (Crustacea, Decapoda, Ocypodidae).

Light and scanning electron microscopy (SEM) were used to examine the first zoeal stage of four ghost crabs, Ocypode ceratophthalmus (Pallas, 1772), O. cordimanus Latreille, 1818, O. sinensis Dai, Song & Yang, 1985 and O. stimpsoni Ortmann, 1897. Finding diagnostic characters to distinguish between the four species proved difficult because their setal appendage patterns were identical. However the rectangular and pockmarked patterns on the ventral carapace are rather pronounced in O. ceratophthalmus and O. stimpsoni but weak in O. cordimanus and O. sinensis. The spinulation on the furca of the telson is less in O. cordimanus than in the other three species.

Dual-Energy-Barrier Stable Superhydrophobic Structures for Long Icing Delay.

Using superhydrophobic surfaces (SHSs) with the water-repellent Cassie-Baxter (CB) state is widely acknowledged as an effective approach for anti-icing performances. Nonetheless, the CB state is susceptible to diverse physical phenomena (e.g., vapor condensation, gas contraction, etc.) at low temperatures, resulting in the transition to the sticky Wenzel state and the loss of anti-icing capabilities. SHSs with various micronanostructures have been empirically examined for enhancing the CB stability; however, the energy barrier transits from the metastable CB state to the stable Wenzel state and thus the CB stability enhancement is currently not enough to guarantee a well and appliable anti-icing performance at low temperatures. Here, we proposed a dual-energy-barrier design strategy on superhydrophobic micronanostructures. Rather than the typical single energy barrier of the conventional CB-to-Wenzel transition, we introduced two CB states (i.e., CB I and CB II), where the state transition needed to go through CB I and CB II then to Wenzel state, thus significantly improving the entire CB stability. We applied ultrafast laser to fabricate this dual-energy-barrier micronanostructures, established a theoretical framework, and performed a series of experiments. The anti-icing performances were exhibited with long delay icing times (over 27,000 s) and low ice-adhesion strengths (0.9 kPa). The kinetic mechanism underpinning the enhanced CB anti-icing stability was elucidated and attributed to the preferential liquid pinning in the shallow closed structures, enabling the higher CB-Wenzel transition energy barrier to sustain the CB state. Comprehensive durability tests further corroborated the potentials of the designed dual-energy-barrier structures for anti-icing applications.

Localized in-situ deposition: a new dimension to control in fabricating surface micro/nano structures via ultrafast laser ablation.

Controllable fabrication of surface micro/nano structures is the key to realizing surface functionalization for various applications. As a versatile approach, ultrafast laser ablation has been widely studied for surface micro/nano structuring. Increasing research efforts in this field have been devoted to gaining more control over the fabrication processes to meet the increasing need for creation of complex structures. In this paper, we focus on the in-situ deposition process following the plasma formation under ultrafast laser ablation. From an overview perspective, we firstly summarize the different roles that plasma plumes, from pulsed laser ablation of solids, play in different laser processing approaches. Then, the distinctive in-situ deposition process within surface micro/nano structuring is highlighted. Our experimental work demonstrated that the in-situ deposition during ultrafast laser surface structuring can be controlled as a localized micro-additive process to pile up secondary ordered structures, through which a unique kind of hierarchical structure with fort-like bodies sitting on top of micro cone arrays were fabricated as a showcase. The revealed laser-matter interaction mechanism can be inspiring for the development of new ultrafast laser fabrication approaches, adding a new dimension and more flexibility in controlling the fabrication of functional surface micro/nano structures.

Superhydrophobic microstructures for better anti-icing performances: open-cell or closed-cell?

Based on geometrical characteristics, all surface microstructures are categorized into two types: closed-cell and open-cell structures. Closed-cell structures are well-known to have more stable and durable superhydrophobicity at room temperatures. However, in low-temperature environments where massive environmentally induced physical changes emerge, whether closed-cell surfaces can maintain good anti-icing performances has not yet been confirmed, and thus how to design optimal superhydrophobic anti-icing microstructures is rarely reported. Here, we apply an ultrafast laser to fabricate superhydrophobic surfaces with tunable patterned micro-nanostructures from a complete closed-cell to different ratios and to a complete open-cell. We discover that droplets on closed-cell structures completely degrade to the high-adhesion Wenzel state after icing and melting cycles while those on the open-cell structures well recover to the original Cassie-Baxter state. We propose an improved ideal gas model to clarify the mechanisms that the decreased air pocket pressure and the air dissolution on closed-cell structures induce easy impalement during icing and the difficult recovery during melting, paving the way for optimizing the anti-icing structure design. The optimized open-cell surfaces exhibit over 33 times lower ice adhesion strengths (1.4 kPa) and long-term icephobic durability (<20 kPa after 33 deicing cycles) owing to the increased air pocket pressure at low temperatures. Significant dewetting processes during condensation endow the open-cell structures with more remarkable high-humidity resistance and anti-frosting properties. Our study reveals the general design principle of superhydrophobic anti-icing structures, which might guide the design of superhydrophobic anti-icing surfaces in practical harsh environments.

Boosting water evaporation via continuous formation of a 3D thin film through triple-level super-wicking routes.

Capillary-fed thin-film evaporation via micro/nanoscale structures has attracted increasing attention for its high evaporation flux and pumpless liquid replenishment. However, maximizing thin-film evaporation has been hindered by the intrinsic trade-off between the heat flux and liquid transport. Here, we designed and fabricated nanostructured micro-steam volcanoes on copper surfaces featuring triple-level super-wicking routes to overcome this trade-off and boost water evaporation. The triple-level super-wicking routes enable the continuous formation of a 3D thin film for highly efficient evaporation by continuous self-driven liquid replenishment and extending the thin-film region. The micro-steam volcanoes increased the surface area by 225%, improving the evaporation rate by 141%, with a rapid self-pumping water transport speed up to 80 mm s-1. A remarkable solar-driven water evaporation rate of 3.33 kg m-2 h-1 under one sun vertical incidence was achieved, which is among the highest reported values for metal-based evaporators. When attached to electric-heating plates, the evaporator realized an electrothermal evaporation rate of 12.13 kg m-2 h-1. Moreover, it can also be used for evaporative cooling with enhanced convective heat transfer, reaching a 36.2 °C temperature reduction on a heat source with a heat flux of 6 W cm-2. This study promises a general strategy for designing thin-film evaporators with high efficiencies, low costs, and multi-functional compatibilities.

A new wriggler of Eleotrid (Teleostei: Xenisthmidae) from Taiwan.

A new wriggler of genus Xenisthmus was collected from Taitung and Pingtung Counties, Taiwan, while using SCUBA diving of coral reef fish survey. The new species, Xenisthmus nigrolateralis, can be well distinguished from other congeners by the following unique combination of features: (1) fins: second dorsal fin rays I/13; anal fin rays I/13; pectoral fin rays16; (2) squamation: longitudinal scale series 68-70; perdorsal scales 23; (3) vertebral count 10+16=26; (4) preopercular canal present with rather more, 5 pores γ1, γ, δ, ε, and ε1 and (5) specific colouration: lateral side with broad, deep brown stripe from rear of lateral gill opening to caudal fin base, and caudal fin with median blackish brown mark, and upper and lower regions translucent, the base with a vertical black bar. The comparison of other congeners would be also discussed in this paper.

Spontaneous dewetting transitions of droplets during icing & melting cycle.

Anti-icing superhydrophobic surfaces have been a key research topic due to their potential application value in aviation, telecommunication, energy, etc. However, superhydrophobicity is easily lost during icing & melting cycles, where the water-repellent Cassie-Baxter state turns to the sticky Wenzel state. The reversible transition during icing & melting cycle without external assistance is challenging but vital for reliable anti-icing superhydrophobic performance, such a topic has rarely been reported. Here we demonstrate a spontaneous Wenzel to Cassie-Baxter dewetting transition during icing & melting cycle on well-designed superhydrophobic surfaces. Bubbles in ice droplets rapidly impact the micro-nano valleys under Marangoni force, prompting the continuous recovery of air pockets during melting processes. We establish models to confirm the bubbles movement broadens the dewetting conditions greatly and present three criteria for the dewetting transitions. This research deepens the understanding of wettability theory and extends the design of anti-icing superhydrophobic surfaces.

Micro-Nano-Nanowire Triple Structure-Held PDMS Superhydrophobic Surfaces for Robust Ultra-Long-Term Icephobic Performance.

Anti-icing superhydrophobic surfaces have attracted tremendous interests due to their repellency to water and extremely low ice affinity, whereas the weak durability has been the bottleneck for further applications. Surface durability is especially important in long-term exposure to low-temperature and high-humidity environments. In this study, a robust micro-nano-nanowire triple structure-held PDMS superhydrophobic surface was fabricated via a hybrid process: ultrafast-laser-prepared periodic copper microstructures were chemically oxidized, followed by modification of PDMS. The hedgehog-like surface structure was composed of microcones, densely grown nanowires, and tightly combined PDMS. The capillary force difference in micro-nanostructures drove PDMS solutions to distribute evenly, bonding fragile nanowires to form stronger composite cones. PDMS replaced the commonly used fragile fluorosilanes and protected nanowires from breaking, which endowed the surfaces with higher robustness. The ductile PDMS-nanowire composites possessed higher resiliency than brittle nanowires under a load of 1 mN. The surface kept superhydrophobic and ice-resistant after 15 linear abrasion cycles under 1.2 kPa or 60 icing-deicing cycles under -20 °C or 500 tape peeling cycles. Under a higher pressure of 6.2 kPa, the contact angle (CA) was maintained above 150° until the abrasion distance exceeded 8 m. In addition, the surface exhibited a rare spontaneously optimized performance in the icing-deicing cycles. The ice adhesion strength of the surface reached its lowest value of 12.2 kPa in the 16th cycle. Evolution of surface roughness and morphology were combined to explain its unique U-shaped performance curves, which distinguished its unique degradation process from common surfaces. Thus, this triple-scale superhydrophobic surface showed a long-term anti-icing performance with high deicing robustness and low ice adhesion strength. The proposed nanostructure-facilitated uniform distribution strategy of PDMS is promising in future design of durable superhydrophobic anti-icing surfaces.

Morphology of the first three zoeal stages of the deep-sea caridean shrimp Heterocarpus fascirostratus Yang, Chan & Kumar, 2018 (Crustacea, Decapoda, Pandalidae).

The larvae of the deep-sea pandalid shrimp Heterocarpus fascirostratus Yang, Chan & Kumar, 2018 were successfully hatched and cultured to the third zoeal stage. The larvae reached the third zoeal stage nine days after hatching at a water temperature of 21 ± 1 °C. Although members of Heterocarpus A. Milne-Edwards, 1881 have rather diverse body forms and are often separated into many species groups, the early zoeal morphology of H. fascirostratus follows the general developmental pattern of the species in Heterocarpus. The main differences amongst these larvae are body size, spines on the anteroventral margin of the carapace, and the endopod setation of the third maxilliped.

Directional anchoring patterned liquid-infused superamphiphobic surfaces for high-throughput droplet manipulation.

High-throughput experiments involving isolated droplets based on patterned superwettable surfaces are important for various applications related to biology, chemistry, and medicine, and they have attracted a large amount of interest. This paper provides a directional anchoring liquid-infused superamphiphobic surface (DAS), via combining concepts based on the droplet-anchoring behavior of beetle backs with patterned wettability, the directional adhesion of butterfly wings, and the slippery liquid-infused surfaces (SLISs) of pitcher plants. Regularly arranged ">"-shaped SLIS patterns were created on a superamphiphobic (SAM) background through ultrafast-laser-based technology. Improved directional anchoring abilities with a sliding angle difference of 77° were achieved; this is the largest sliding angle difference in a one-dimensional direction achieved using an artificial surface, to the best of the authors' knowledge. Thanks to the directional anchoring abilities, the DAS coupled droplet 'anchoring' and 'releasing' abilities. Furthermore, a high-throughput droplet manipulation device was designed, on which a micro-droplet array with a large number of droplets can be 'captured', 'transferred', or 'released' in a single step. With the addition of lubricant, the DAS can work continuously for even more than 30 cycles without cross-contamination between different droplets. The DAS also shows good stability under an ambient atmosphere and can maintain its functionality when manipulating corrosive droplets. The DAS and corresponding high-throughput droplet manipulation method are excellent candidates for practical applications.

Description of the First Zoea of the Cavernicolous Crab Karstama boholano (Ng, 2002) (Crustacea: Decapoda: Sesarmidae) from Taiwan, with Notes on Ecology.

This study presents a rare sesarmid cavernicolous crab, Karstama boholano (Ng, 2002), from Taiwan. This genus and species are both new to Taiwan. We describe the diagnostic characteristics of the Taiwanese specimen and provide illustrations of the adult and first zoea, as well as photographs of an adult in its natural habitat. The identity was confirmed by the COI gene sequence and morphological data. In addition, the zoeal morphology and breeding ecology of the genus Karstama Davie and Ng, 2007 are reported for the first time.

First zoeal stage of Plesionika crosnieri Chan Yu, 1991, P. ortmanni Doflein, 1902, and P. semilaevis Bate, 1888, with remarks on the early larvae of Plesionika Bate, 1888 (Crustacea, Decapoda).

The morphology of first stage zoea larvae of three pandalid shrimps Plesionika crosnieri Chan Yu, 1991, P. ortmanni Doflein, 1902, and P. semilaevis Bate, 1888 are described for the first time from larvae obtained in laboratory culture. The zoea I is compared amongst those species of the genus Plesionika with larval morphology known. It is found that the length of the rostrum, the number of anteroventral denticles on the carapace, presence of exopodal setae in the maxillule, and setation pattern of the peduncle of antennule, endopod of antenna, and coxa/basis of maxillipeds are useful characters in distinguishing these larvae.

Larval development to the first eighth zoeal stages in the deep-sea caridean shrimp Plesionika grandis Doflein, 1902 (Crustacea, Decapoda, Pandalidae).

The larvae of the deep-sea pandalid shrimp Plesionika grandis Doflein, 1902 were successfully reared in the laboratory for the first time. The larvae reached the eighth zoeal stage in 36 days, both of which are longest records for the genus. Early larval stages of P. grandis bear the general characters of pandalid shrimps and differ from the other two species of Plesionika with larval morphology known in the number of spines on the anteroventral margin of carapace, number of tubercles on antennule, endopod segmentation in antenna, and third maxilliped setation. Although members in Plesionika are often separated into species groups, members of the same species group do not necessarily have similar early larval morphology. Since the zoea VIII of P. grandis still lacks pleopods and fifth pereiopod, this shrimp likely has at least 12 zoeal stages and a larval development of 120 days.

Redescription of the early larval stages of the pandalid shrimp Chlorotocus crassicornis (Decapoda: Caridea: Pandalidae).

The first four larval stages of the pandalid shrimp Chlorotocus crassicornis (A. Costa, 1871) are described and illustrated from laboratory-reared material obtained from ovigerous females collected in the southwestern Spain and south Taiwan. The second to fourth larval stages of this species are reported for the first time to science. Detailed examination of the first larval stages reveals that previous description misidentified some key larval characters which have prevented its identification in plankton samples. It is found that the zoeal morphology of Chlorotocus is not very different from other pandalid larvae, and in fact closely resembles Plesionika and Heterocarpus.