Phase Transformations Caused by Heat Treatment and High-Pressure Torsion in TiZrHfMoCrCo Alloy.

In this work the high-entropy alloy studied contained six components, Ti/Zr/Hf/Mo/Cr/Co, and three phases, namely one phase with body-centered cubic lattice (BCC) and two Laves phases C14 and C15. A series of annealings in the temperature range from 600 to 1000 °C demonstrated not only a change in the microstructure of the TiZrHfMoCrCo alloy, but also the modification of phase composition. After annealing at 1000 °C the BCC phase almost fully disappeared. The annealing at 600 and 800 °C leads to the formation of new Laves phases. After high-pressure torsion (HPT) of the as-cast TiZrHfMoCrCo alloy, the grains become very small, the BCC phase prevails, and C14 Laves phase completely disappears. This state is similar to the state after annealing at high effective temperature Teff. The additional annealing at 1000 °C after HPT returns the phase composition back to the state similar to that of the as-cast alloy after annealing at 1000 °C. At 1000 °C the BCC phase completely wets the C15/C15 grain boundaries (GBs). At 600 and 800 °C the GB wetting is incomplete. The big spread of nanohardness and Young's modulus for the BCC phase and (C15 + C14) Laves phases is observed.

Influence of the Phase Composition of Titanium Alloys on Cell Adhesion and Surface Colonization.

The pivotal role of metal implants within the host's body following reconstructive surgery hinges primarily on the initial phase of the process: the adhesion of host cells to the implant's surface and the subsequent colonization by these cells. Notably, titanium alloys represent a significant class of materials used for crafting metal implants. This study, however, marks the first investigation into how the phase composition of titanium alloys, encompassing the volume fractions of the α, ß, and ω phases, influences cell adhesion to the implant's surface. Moreover, the research delves into the examination of induced hemolysis and cytotoxicity. To manipulate the phase composition of titanium alloys, various parameters were altered, including the chemical composition of titanium alloys with iron and niobium, annealing temperature, and high-pressure torsion parameters. By systematically adjusting these experimental parameters, we were able to discern the distinct impact of phase composition. As a result, the study unveiled that the colonization of the surfaces of the examined Ti-Nb and Ti-Fe alloys by human multipotent mesenchymal stromal cells exhibits an upward trend with the increasing proportion of the ω phase, concurrently accompanied by a decrease in the α and ß phases. These findings signify a new avenue for advancing Ti-based alloys for both permanent implants and temporary fixtures, capitalizing on the ability to regulate the volume fractions of the α, ß, and ω phases. Furthermore, the promising characteristics of the ω phase suggest the potential emergence of a third generation of biocompatible Ti alloys, the ω-based materials, following the first-generation α-Ti alloys and second-generation ß alloys.

Formation and Thermal Stability of the ω-Phase in Ti-Nb and Ti-Mo Alloys Subjected to HPT.

This paper discusses the features of ω-phase formation and its thermal stability depending on the phase composition, alloying element and the grain size of the initial microstructure of Ti-Nb and Ti-Mo alloys subjected to high-pressure torsion (HPT) deformation. In the case of two-phase Ti-3wt.% Nb and Ti-20wt.% Nb alloys with different volume fractions of α- and ß-phases, a complete ß→ω phase transformation and partial α→ω transformation were found. The dependence of the α→ω transformation on the concentration of the alloying element was determined: the greater content of Nb in the α-phase, the lower the amount of ω-phase that was formed from it. In the case of single-phase Ti-Mo alloys, it was found that the amount of ω-phase formed from the coarse-grained ß-phase of the Ti-18wt.% Mo alloy was less than the amount of the ω-phase formed from the fine α'-martensite of the Ti-2wt.% Mo alloy. This was despite the fact that the ω-phase is easier to form from the ß-phase than from the α- or α'-phase. It is possible that the grain size of the microstructure also affected the phase transformation, namely, the fine martensitic plates more easily gain deformation and overcome the critical shear stresses necessary for the phase transformation. It was also found that the thermal stability of the ω-phase in the Ti-Nb and Ti-Mo alloys increased with the increasing concentration of Nb or Mo.

Omega Phase Formation in Ti-3wt.%Nb Alloy Induced by High-Pressure Torsion.

It is well known that severe plastic deformation not only leads to strong grain refinement and material strengthening but also can drive phase transformations. A study of the fundamentals of α → ω phase transformations induced by high-pressure torsion (HPT) in Ti-Nb-based alloys is presented in the current work. Before HPT, a Ti-3wt.%Nb alloy was annealed at two different temperatures in order to obtain the α-phase state with different amounts of niobium. X-ray diffraction analysis, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were applied for the characterisation of phase transitions and evolution of the microstructure. A small amount of the ß-phase was found in the initial states, which completely transformed into the ω-phase during the HPT process. During HPT, strong grain refinement in the α-phase took place, as did partial transformation of the α- into the ω-phase. Therefore, two kinds of ω-phase, each with different chemical composition, were obtained after HPT. The first one was formed from the ß-phase, enriched in Nb, and the second one from the α-phase. It was also found that the transformation of the α-phase into the ω-phase depended on the Nb concentration in the α-Ti phase. The less Nb there was in the α-phase, the more of the α-phase was transformed into the ω-phase.

Microstructure, Microhardness and Corrosion Resistance of WE43 Alloy Based Composites after High-Pressure Torsion.

The structure and properties of a composite consisting of Mg-Y-Nd-Zr alloy (WE43) and various oxides are studied. The particles of the WE43 powder were coated by the nanocrystalline oxide layer by means of a wet chemical deposition process. After that the powder is compressed into solid samples and deformed using high-pressure torsion at room temperature. A second phase is present, both, in pure WE43 alloy and in the one with deposited oxides. We observed that the modification of the alloy by the oxide layer deposition and deformation by high-pressure torsion changes the phase composition and properties of the samples. The samples modified by TiO2 showed the best microhardness and corrosion resistance.

Dissolution of Ag Precipitates in the Cu⁻8wt.%Ag Alloy Deformed by High Pressure Torsion.

The aim of this work was to study the influence of severe plastic deformation (SPD) on the dissolution of silver particles in Cu⁻8wt.%Ag alloys. In order to obtain different morphologies of silver particles, samples were annealed at 400, 500 and 600 °C. Subsequently, the material was subjected to high pressure torsion (HPT) at room temperature. By means of scanning and transmission electron microscopy, as well as X-ray diffraction techniques, it was found that during SPD, the dissolution of second phase was strongly affected by the morphology and volume fraction of the precipitates in the initial state. Small, heterogeneous precipitates of irregular shape dissolved more easily than those of large size, round-shaped and uniform composition. It was also found that HPT led to the increase of solubility limit of silver in the copper matrix as the result of dissolution of the second phase. This unusual phase transition is discussed with respect to diffusion activation energy and mixing enthalpy of the alloying elements.

Microstrain and electrochemical performance of garnet solid electrolyte integrated in a hybrid battery cell.

Garnet type solid electrolytes are promising candidates for replacing the flammable liquid electrolytes conventionally used in Li-ion batteries. Al-doped Li7La3Zr2O12 (LLZO) is synthesized using nebulized spray pyrolysis and field assisted sintering technology (FAST), a novel synthesis route ensuring the preparation of samples with a homogeneous elemental distribution and dense ceramic electrolytes. Ceramic preparation utilizing field assisted sintering, in particular the applied pressure, has significant influence on the material structure, i.e. microstrain, and thereby its electrochemical performance. The phenomenon of microstrain enhancement of electrochemical performance might open a new route towards improved garnet solid electrolytes. A detailed mechanism is proposed for the lattice distortion and resulting microstrain during sintering. The charge transfer resistance of Li-ions at the interface between LLZO and Li is characterized using AC impedance spectroscopy and is amongst the best reported values to date. Additionally, the solid electrolyte is integrated in a full hybrid cell, a practical approach combining all the advantages of the solid electrolyte, while maintaining good contact with the cathode material.

Structural and Mechanical Properties of Ti⁻Co Alloys Treated by High Pressure Torsion.

The microstructure and properties of titanium-based alloys can be tailored using severe plastic deformation. The structure and microhardness of Ti⁻4 wt.% Co alloy have been studied after preliminary annealing and following high pressure torsion (HPT). The Ti⁻4 wt.% Co alloy has been annealed at 400, 500, and 600 °C, i.e., below the temperature of eutectoid transformation in the Ti⁻4 wt.% Co system. The amount of Co dissolved in α-Ti increased with increasing annealing temperature. HPT led to the transformation of α-Ti in ω-Ti. After HPT, the amount of ω-phase in the sample annealed at 400 °C was about 80-85%, i.e., higher than in pure titanium (about 40%). However, with increasing temperature of pre-annealing, the portion of ω-phase decreased (60⁻65% at 500 °C and about 5% at 600 °C). The microhardness of all investigated samples increased with increasing temperature of pre-annealing.