Assessment and source identification of As and Cd contamination in soil and plants in the vicinity of the Nui Phao Mine, Vietnam.

This study investigated the contamination levels and sources of As and Cd vicinity area from Nui Phao mine that is one of the largest tungsten (W) open pit mines in the world. Soil and plant samples were collected from the study area to identify the concentrations of As and Cd using aqua-regia or HNO3 digestion. According to the Vietnamese agricultural soil criteria, all soil samples were contaminated with As and Cd. The distribution of As concentration is related to the distance from the Nui Phao mine. The higher As concentrations were measured in the area close to the mine. However, the Cd distribution in the soil showed a different pattern from As. Enrichment factor and Geoaccumulation Index (Igeo) indicated that As in the soil is derived from the mining activities, while Cd could have other geogenic or anthropogenic sources. The ranges of As and Cd concentration in polished rice grains in the Nui Phao mine area exceeded the CODEX criteria (0.2 mg/kg), which indicated extreme contamination. The arsenic concentration between soil and plant samples was determined to be a positive correlation, while the Cd concentration showed a negative correlation, implying that As and Cd have different geochemical behavior based on their sources.

Dual-line fabrication method in direct laser lithography to reduce the manufacturing time of diffractive optics elements.

To reduce the manufacturing time of DOEs (Diffractive Optics Elements) and POEs (Periodical Optics Elements), a new fabrication method in direct laser lithography is proposed based on the laser ablation phenomenon and the thermochemical effect of chrome. The basic mechanism of the proposed method and experimental results are also presented. It was found that when a 3 × 3 rectangular pattern is fabricated, the proposed method can reduce the total lithographic length by approximately 33%. The manufacturing time is reduced by nearly 52%. When fabricating a 1,000 × 1,000 rectangular pattern, the manufacturing time was reduced by more than 90%. The time reduction rate is drastically improved when the number of patterns is increased. Various patterns including rectangular, triangular, parallelogram, and diamond shape were fabricated by using the proposed method.

Low cost wafer metrology using a NIR low coherence interferometry.

In this investigation, a low cost Si wafer metrology system based on low coherence interferometry using NIR light is proposed and verified. The whole system consists of two low coherence interferometric principles: low coherence scanning interferometry (LCSI) for measuring surface profiles and spectrally-resolved interferometry (SRI) to obtain the nominal optical thickness of the double-sided polished Si wafer. The combination of two techniques can reduce the measurement time and give adequate dimensional information of the Si wafer. The wavelength of the optical source is around 1 µm, for which transmission is non-zero for undoped silicon and can be also detected by a typical CCD camera. Because of the typical CCD camera, the whole system can be constructed inexpensively.

Quantifiable and feasible estrus detection using the ultrasonic sensor array and digital infrared thermography.

Detection of estrus is an essential factor as a method of successful breeding in the sow. As increasing the adaption of the information and communication technology (ICT) into swine industry, this study focuses on a possibility and quantification of standing time, vulva and body temperature as methods of estrus detection, comparing each time and temperature in estrus and non-estrus period, and analyzing each success rate of new and existing methods. Ultrasonic sensor array and digital infrared thermography were used to evaluate whether new methods such as standing time and number, and vulva and skin temperature can be replaced, or these methods can be quantifiable in estrus period. Ultrasonic sensor array was installed beside the stall and digital infrared thermography was placed in the rear of sow to collect the dates of sow in estrus and non-estrus period. This study showed total standing time, number and number over 10 minutes, and vulva temperature of the sow in estrus period were increased (p < 0.05) compared with those of sow in non-estrus period, respectively. Detection of estrus using standing time and vulva temperature tended (p = 0.06) to increase the success rate when artificial insemination (AI) was performed. In conclusion, standing time and vulva temperature increased when estrus happened. Success rate of AI of sow using these methods showed an increasing trend. Therefore, existing method using the naked eye can be replaced to new method such as vulvar temperature and standing time when detecting the estrus.