RESUMO
Hydrogen (H2 ) produced from renewables will have a growing impact on the global energy dynamics towards sustainable and carbon-neutral standards. The share of green H2 is still too low to meet the net-zero target, while the demand for high-quality hydrogen continues to rise. These factors amplify the need for economically viable H2 generation technologies. The present article aims at evaluating the existing technologies for high-quality H2 production based on solar energy. Technologies such as water electrolysis, photoelectrochemical and solar thermochemical water splitting, liquid metal reactors and plasma conversion utilize solar power directly or indirectly (as carbon-neutral electrons) and are reviewed from the perspective of their current development level, technical limitations and future potential.
RESUMO
Pt dissolution has already been intensively studied in aqueous model systems and many mechanistic insights have been gained. Nevertheless, transfer of new knowledge to real-world fuel cell systems is still a significant challenge. To close this gap, we present a novel inâ situ method combining a gas diffusion electrode (GDE) half-cell with inductively coupled plasma mass spectrometry (ICP-MS). With this setup, Pt dissolution in realistic catalyst layers and the transport of dissolved Pt species through Nafion membranes were evaluated directly. We observed that 1)â specific Pt dissolution increased significantly with decreasing Pt loading, 2)â in comparison to experiments on aqueous model systems with flow cells, the measured dissolution in GDE experiments was considerably lower, and 3)â by adding a membrane onto the catalyst layer, Pt dissolution was reduced even further. All these phenomena are attributed to the varying mass transport conditions of dissolved Pt species, influencing re-deposition and equilibrium potential.
RESUMO
Invited for this month's cover is the group of Dunwei Wang from Boston College and Serhiy Cherevko from the Helmholtz Institute Erlangen-Nürnberg for Renewable Energy. The image illustrates the impact of different electrolyte environments on the stability of hematite decorated with an iridium molecular catalyst used for solar water splitting. The Research Article itself is available at 10.1002/cssc.202202319.
RESUMO
Molecular catalysts are promising oxygen evolution promoters in conjunction with photoanodes for solar water splitting. Maintaining the stability of both photoabsorber and cocatalyst is still a prime challenge, with many efforts tackling this issue through sophisticated material designs. Such approaches often mask the importance of the electrode-electrolyte interface and overlook easily tunable system parameters, such as the electrolyte environment, to improve efficiency. We provide a systematic study on the activity-stability relationship of a prominent Fe2 O3 photoanode modified with Ir molecular catalysts using in situ mass spectroscopy. After gaining detailed insights into the dissolution behavior of the Ir cocatalyst, a comprehensive pH study is conducted to probe the impact of the electrolyte on the performance. An inverse trend in Fe and Ir stability is found, with the best activity-stability synergy obtained at pHâ 9.7. The results bring awareness to the overall photostability and electrolyte engineering when advancing catalysts for solar water splitting.
RESUMO
Electrodeposition of high-surface-area nanoporous Au-Cu foams under conditions of hydrogen codeposition is studied. The honeycomb-like Au(x)Cu(100-x) foams with 0 ≤ x ≤ 100 are electrodeposited by controlling the amount of corresponding ions in the solution. The amount of metal ions in deposited films follows that in used electrolytes. Compared to monometallic foams, the Au(x)Cu(100-x) structures are characterized by smaller ligament or particle sizes (less than 10 nm) and improved stability. The addition of even a small amount of Cu to the Au matrix is found to dramatically improve the stability of the structure in air environment or an acidic medium. Pt@Au(x)Cu(100-x) structures are formed by the galvanic displacement of Cu from Au(x)Cu(100-x) templates. During the displacement of Cu by Pt, Au serves as a buffer, decreasing mechanical stresses and preventing the detachment of the foam from the substrate. The surface ratio of Pt to Au atoms is controlled by adjusting the amount of Cu in the template. Pt@Au(x)Cu(100-x) electrodes are investigated as novel electrocatalysts for methanol oxidation in alkaline media. The Au-enriched surfaces show higher catalytic activity toward methanol oxidation, while the electrodes with a higher amount of Pt are more stable.
RESUMO
Palladium nanotube and nanowire arrays were fabricated by electrodeposition into anodic alumina oxide (AAO) templates. By using alumina templates with different pore sizes and hole mouth morphologies, nanotubes with various diameters and lengths were obtained. The mechanism of nano-structure formation was studied by analyzing the current-time curves. It was found that the time needed for the transformation of the nanostructure from a tube to a wire depends on the size and structure of the template. However, the overall behaviour of the current-time transient is similar and can be divided into four main stages, which provides a powerful in-situ method to control nanotube-nanowire transition during growth. The palladium nanotube arrays have a polycrystalline structure, but a preferred orientation along the (110) direction was observed for the arrays of nanowires. Moreover, the degree of texture increases with decreasing alumina pore size.
RESUMO
One of the most important practical issues in low-temperature fuel-cell catalyst degradation is platinum dissolution. According to the literature, it initiates at 0.6-0.9â VRHE, whereas previous time- and potential-resolved inductively coupled plasma mass spectrometry (ICP-MS) experiments, however, revealed dissolution onset at only 1.05â VRHE. In this manuscript, the apparent discrepancy is addressed by investigating bulk and nanoparticulated catalysts. It is shown that, given enough time for accumulation, traces of platinum can be detected at potentials as low as 0.85â VRHE. At these low potentials, anodic dissolution is the dominant process, whereas, at more positive potentials, more platinum dissolves during the oxide reduction after accumulation. Interestingly, the potential and time dissolution dependence is similar for both types of electrode. Dissolution processes are discussed with relevance to fuel-cell operation and plausible dissolution mechanisms are considered.
RESUMO
High surface area Pd foams with roughness factors of more than 1000 and a specific surface area of 60 m(2) g(-1) are obtained by electrodeposition. The foams are composed of dendrites with branches on the 10 nm scale. The resulting electrodes show high activity towards the oxidation of C(2) alcohols.
RESUMO
Hydrogen evolution assisted electrodeposition is a new bottom-up technique allowing the fast and simple synthesis of nanometals. Electrochemical dealloying is a top-down approach with the same purpose. In this work, we show that a combination of these two methods in sequence by pulse-reverse electrodeposition can be used to prepare high-surface-area nanostructured metals. Highly porous adherent platinum is obtained by the deposition of CuPt alloy during the cathodic cycles and the selective dissolution of copper during the anodic cycles. The convection created by the movement of the hydrogen bubbles increases the deposition rate and removes the dissolved copper ions from the diffusion layer, which ensures the deposition of a film with the same stoichiometry throughout the whole process. Due to the relatively high ratio of copper atoms on the surface in the as-deposited layer, it is proposed that the dealloying kinetics is significantly higher than that usually observed during the dealloying process in a model system. The proposed approach has several advantages over other methods, such as a very high growth rate and needlessness of any post-treatment processes. A detailed analysis of the effect of pulse-reverse waveform parameters on the properties of the films is presented. Mesoporous platinum with pores and ligaments having characteristic sizes of less than 10 nm, an equivalent surface area of up to ca. 220 m(2) cm(-3), and a roughness factor of more than 1000 is fabricated.