Superhydrophobic surfaces for extreme environmental conditions.

Superhydrophobic surfaces for repelling impacting water droplets are typically created by designing structures with capillary (antiwetting) pressures greater than those of the incoming droplet (dynamic, water hammer). Recent work has focused on the evolution of the intervening air layer between droplet and substrate during impact, a balance of air compression and drainage within the surface texture, and its role in affecting impalement under ambient conditions through local changes in the droplet curvature. However, little consideration has been given to the influence of the intervening air-layer thermodynamic state and composition, in particular when departing from standard atmospheric conditions, on the antiwetting behavior of superhydrophobic surfaces. Here, we explore the related physics and determine the working envelope for maintaining robust superhydrophobicity, in terms of the ambient pressure and water vapor content. With single-tier and multitier superhydrophobic surfaces and high-resolution dynamic imaging of the droplet meniscus and its penetration behavior into the surface texture, we expose a trend of increasing impalement severity with decreasing ambient pressure and elucidate a previously unexplored condensation-based impalement mechanism within the texture resulting from the compression, and subsequent supersaturation, of the intervening gas layer in low-pressure, humid conditions. Using fluid dynamical considerations and nucleation thermodynamics, we provide mechanistic understanding of impalement and further employ this knowledge to rationally construct multitier surfaces with robust superhydrophobicity, extending water repellency behavior well beyond typical atmospheric conditions. Such a property is expected to find multifaceted use exemplified by transportation and infrastructure applications where exceptional repellency to water and ice is desired.

Freezing-induced wetting transitions on superhydrophobic surfaces.

Supercooled droplet freezing on surfaces occurs frequently in nature and industry, often adversely affecting the efficiency and reliability of technological processes. The ability of superhydrophobic surfaces to rapidly shed water and reduce ice adhesion make them promising candidates for resistance to icing. However, the effect of supercooled droplet freezing-with its inherent rapid local heating and explosive vaporization-on the evolution of droplet-substrate interactions, and the resulting implications for the design of icephobic surfaces, are little explored. Here we investigate the freezing of supercooled droplets resting on engineered textured surfaces. On the basis of investigations in which freezing is induced by evacuation of the atmosphere, we determine the surface properties required to promote ice self-expulsion and, simultaneously, identify two mechanisms through which repellency falters. We elucidate these outcomes by balancing (anti-)wetting surface forces with those triggered by recalescent freezing phenomena and demonstrate rationally designed textures to promote ice expulsion. Finally, we consider the complementary case of freezing at atmospheric pressure and subzero temperature, where we observe bottom-up ice suffusion within the surface texture. We then assemble a rational framework for the phenomenology of ice adhesion of supercooled droplets throughout freezing, informing ice-repellent surface design across the phase diagram.

Transparent Photothermal Metasurfaces Amplifying Superhydrophobicity by Absorbing Sunlight.

Imparting and maintaining surface superhydrophobicity has been receiving significant research attention over the last several years, driven by a broad range of important applications and enabled by advancements in materials and surface nanoengineering. Researchers have investigated the effect of temperature on droplet-surface interactions, which poses additional challenges when liquid nucleation manifests itself, due to ensuing condensation into the surface texture that compromises its antiwetting behavior. Maintaining surface transparency at the same time poses an additional and significant challenge. Often, the solutions proposed are limited by working temperatures or are detrimental to visibility through the surface. Here we introduce a scalable method employing plasmonic photothermal metasurface composites, able to harvest sunlight and naturally heat the surface, sustaining water repellency and transparency under challenging environmental conditions where condensation and fogging would otherwise be strongly promoted. We demonstrate that these surfaces, when illuminated by sunlight, can prevent impalement of impacting water droplets, even when the droplet to surface temperature difference is 50 °C, by suppressing condensate formation within the texture, maintaining transparency. We also show how the same transparent metasurface coating could be combined and work collaboratively with hierarchical micro- and nanorough textures, resulting in simultaneous superior pressure-driven impalement resistance and avoidance of water nucleation and related possible frosting in supercooled conditions. Our work can find a host of applications as a sustainable solution against impacting water on surfaces such as windows, eyewear, and optical components.