Solar to hydrocarbon production using metal-free water-soluble bulk heterojunction of conducting polymer nanoparticle and graphene oxide.

This work demonstrates the first example of interfacial manipulation in a hybrid photocatalyst based on poly(3-hexylthiophene-2,5-diyl) (P3HT) nanoparticle and graphene oxide (GO) bulk heterojunctions to efficiently reduce CO2 into selective industrial hydrocarbons under gas-phase reaction and visible-light illumination. High selectivity of chemical products (methanol and acetaldehyde) was observed. Moreover, the hybrid photocatalyst's solar-to-fuel conversion efficiency was 13.5 times higher than that of pure GO. The increased production yield stems from the co-catalytic and sensitizing role of P3HT in the hybrid system due to its ability to extend light absorption to the visible range and improve interfacial charge transfer to GO. The hybrid P3HT-GO formed a type II heterojunction, and its static and dynamic exciton behaviors were examined using fluorescence spectroscopy and exciton lifetime mapping. A reduced fluorescence decay time was observed by interfacial manipulation for improved dispersion, indicating a more efficient charge transfer from the excited P3HT to GO. Thus, the conducting polymer nanoparticles, 2D nanocarbon, have demonstrated superior performance as a metal-free, non-toxic, low-cost, and scalable heterogeneous photocatalyst for CO2 reduction to solar fuel, a solid-gas system.

Ni-Nanocluster Modified Black TiO2 with Dual Active Sites for Selective Photocatalytic CO2 Reduction.

One of the key challenges in artificial photosynthesis is to design a photocatalyst that can bind and activate the CO2 molecule with the smallest possible activation energy and produce selective hydrocarbon products. In this contribution, a combined experimental and computational study on Ni-nanocluster loaded black TiO2 (Ni/TiO2[Vo] ) with built-in dual active sites for selective photocatalytic CO2 conversion is reported. The findings reveal that the synergistic effects of deliberately induced Ni nanoclusters and oxygen vacancies provide (1) energetically stable CO2 binding sites with the lowest activation energy (0.08 eV), (2) highly reactive sites, (3) a fast electron transfer pathway, and (4) enhanced light harvesting by lowering the bandgap. The Ni/TiO2[Vo] photocatalyst has demonstrated highly selective and enhanced photocatalytic activity of more than 18 times higher solar fuel production than the commercial TiO2 (P-25). An insight into the mechanisms of interfacial charge transfer and product formation is explored.

Probing the active site in single-atom oxygen reduction catalysts via operando X-ray and electrochemical spectroscopy.

Nonnoble metal catalysts are low-cost alternatives to Pt for the oxygen reduction reactions (ORRs), which have been studied for various applications in electrocatalytic systems. Among them, transition metal complexes, characterized by a redox-active single-metal-atom with biomimetic ligands, such as pyrolyzed cobalt-nitrogen-carbon (Co-Nx/C), have attracted considerable attention. Therefore, we reported the ORR mechanism of pyrolyzed Vitamin B12 using operando X-ray absorption spectroscopy coupled with electrochemical impedance spectroscopy, which enables operando monitoring of the oxygen binding site on the metal center. Our results revealed the preferential adsorption of oxygen at the Co2+ center, with end-on coordination forming a Co2+-oxo species. Furthermore, the charge transfer mechanism between the catalyst and reactant enables further Co-O species formation. These experimental findings, corroborated with first-principle calculations, provide insight into metal active-site geometry and structural evolution during ORR, which could be used for developing material design strategies for high-performance electrocatalysts for fuel cell applications.

Side group of poly(3-alkylthiophene)s controlled dispersion of single-walled carbon nanotubes for transparent conducting film.

Controlled dispersion of single-walled carbon nanotubes (SWCNTs) in common solvents is a challenging issue, especially for the rising need of low cost flexible transparent conducting films (TCFs). Utilizing conductive polymer as surfactant to facilitate SWCNTs solubility is the most successful pragmatic approach to such problem. Here, we show that dispersion of SWCNT with polymer significantly relies on the length of polymer side groups, which not only influences the diameter distribution of SWCNTs in solution, also eventually affects their effective TCF performance. Surfactants with longer side groups covering larger nanotube surface area could induce adequate steric effect to stabilize the wrapped SWCNTs against the nonspecific aggregation, as discerned by the optical and microscopic measurements, also evidenced from the resultant higher electrokinetic potential. This approach demonstrates a facile route to fabricate large-area SWCNTs-TCFs exhibiting high transmittance and high conductivity, with considerable uniformity over 10 cm × 10 cm.

Effect of copper oxide oxidation state on the polymer-based solar cell buffer layers.

Transporting buffer layers are important components of polymer-based organic photovoltaic devices. In this study, we have investigated the effects of the oxidation state in copper oxide based buffer layer in conjunction to its role in device performance. We have shown that variation in the oxidation state affects the band alignment and built-in voltage of the device, therefore leading to variation in device performance. Specifically, the fully oxidized copper oxide buffer layer has a valence band position at 5.12 eV, much closer to the highest occupied molecular orbital of poly(3-hexylthiophene-2,5-diyl) (P3HT) (∼5.2 eV), giving a best fill factor and efficiency at 57% and 4.06%, respectively. Lastly, we also demonstrate significant enhancement in device stability, with power conversion efficiency maintained at 75% of the original value even after 40 days, and propose a strategy for recovering the device performance based on the observed property of the oxide buffer layer.