Self-Supporting Multicomponent Hierarchical Network Aerogel as Sulfur Anchoring-Catalytic Medium for Highly Stable Lithium-Sulfur Battery.

The low utilization rate of active materials, shuttle effect of lithium polysulfides (LiPSs), and slow reaction kinetics lead to the extremely low efficiency and poor high current cycle stability of lithium sulfur batteries (Li-S batteries). In this paper, a self-supporting multicomponent hierarchical network aerogel is proposed as the modified cathode (S/GO@MX@VS4 ). It consists of graphene (GO) and MXene nanosheets (MX) loaded with VS4 nanoparticles. The experimental results and first-principles calculations show that the GO@MX@VS4 aerogel has strong adsorption and reversible conversion effects on LiPSs. It can not only inhibit the shuttle effect and improve the utilization rate of active substances by keeping the chain crystal structure of VS4 , but also promote the reversibility and kinetics of the reaction by accelerating the liquid-solid transformation in the reduction process and the decomposition of insoluble Li2 S in the oxidation process. The GO@MX@VS4 aerogel modified cathode with a multicomponent synergy exhibits the capacity ratios (Q1 /Q2 ) at different discharge stages is close to the theoretical value (1:2.8), and the capacity decay per cycle is 0.019% in 1200 cycles at 5C. Also, a high areal capacity of 6.90 mAh cm-2 is provided even at high sulfur loading (7.39 mg cm-2 ) and low electrolyte/sulfur ratio (E/S, 8.0 µL mg-1 ).

Facile Vertical Structure Broadband Photodetectors Enabled by Polyvinylpyrrolidone-Regulated Perovskite and Near-Infrared-Sensitive Lead Phthalocyanine.

Broadband photodetectors have drawn tremendous attention in many application areas such as imaging, optical communication, and biochemical sensing. Perovskite is a star material with broad spectral absorption, but it is challenging to develop ultraviolet-visible-near-infrared (UV-Vis-NIR) ultra-broadband photodetectors due to the insufficient absorption in the near-infrared region. Moreover, it is difficult to construct a diode-type photodetector with a simple vertical structure based only on perovskite materials. Here, facile vertical structure broadband photodetectors were fabricated based on heterojunctions that were composed of perovskite MAPbI3 films with UV-Vis absorption spectrum and small organic molecule lead phthalocyanine (PbPc) with strong NIR optical absorption, resulting in UV-Vis-NIR ultra-broadband photodetection. The quality of MAPbI3 films was improved by introducing polyvinylpyrrolidone (PVP) modification, and subsequently, the corresponding MAPbI3/PbPc heterojunction-based photodetectors exhibited rectification characteristics and reduced reverse dark currents. When the PVP mass ratio is 1 wt%, the photodetector achieved the best performance that the spectral response uniformity factor was as high as 0.77, the photoresponsivity exceeded 10 A/W, and the photoresponse time was less than 0.5 ms under a light intensity of 0.013 mW/cm2 in the UV-Vis to NIR spectral range. These results are comparable or superior to those of some inorganic, organic, and perovskite photodetectors reported previously. This study would provide an effective strategy to construct high-performance perovskite photodetectors based on a simple vertical structure, paving the way to the realization of UV-Vis-NIR broadband photodetection.

Preparation and antifouling performance of low-pressure carbon nanotube membranes based on polydopamine biomimetic modification.

In order to investigate the antifouling performance of low-pressure carbon nanotube membranes based on polydopamine (PDA) biomimetic modification, layered multi-walled carbon nanotubes PDA membrane (layered MWCNTs-PDA) and PDA blended MWCNTs membrane (blended PDA/MWCNTs) were prepared. The MWCNTs membranes' antifouling performance and recoverability was significantly improved in filtrating BSA, HA and SA after PDA biomimetic modification, and the total fouling and irreversible fouling were all decreased. Compared with the blended PDA/MWCNTs membrane, the layered MWCNTs-PDA membrane had higher antifouling property as it further improved the electronegativity and hydrophilicity of membrane surface. In addition, denser surface pore size of the layered MWCNTs-PDA membrane can effectively reduce the fouling by trapping foulants on its surface. The combination of PDA biomimetic modification with MWCNTs membrane had a superior antifouling performance and rejection performance in processing NOM and artificial wastewater, and the majority of humic-like foulants could be excluded by the layered MWCNTs-PDA membrane. PDA biomimetic modification alleviated the adhesion of FITC-BSA on the MWCNTs membrane. The layered MWCNTs-PDA membrane especially alleviated the attachment of bacteria and processed excellent antimicrobial ability for bacteria.

Topoarchitected polymer networks expand the space of material properties.

Many living tissues achieve functions through architected constituents with strong adhesion. An Achilles tendon, for example, transmits force, elastically and repeatedly, from a muscle to a bone through staggered alignment of stiff collagen fibrils in a soft proteoglycan matrix. The collagen fibrils align orderly and adhere to the proteoglycan strongly. However, synthesizing architected materials with strong adhesion has been challenging. Here we fabricate architected polymer networks by sequential polymerization and photolithography, and attain adherent interface by topological entanglement. We fabricate tendon-inspired hydrogels by embedding hard blocks in topological entanglement with a soft matrix. The staggered architecture and strong adhesion enable high elastic limit strain and high toughness simultaneously. This combination of attributes is commonly desired in applications, but rarely achieved in synthetic materials. We further demonstrate architected polymer networks of various geometric patterns and material combinations to show the potential for expanding the space of material properties.