Design of a Planar Sensor Based on Split-Ring Resonators for Non-Invasive Permittivity Measurement.

The permittivity of a material is an important parameter to characterize the degree of polarization of a material and identify components and impurities. This paper presents a non-invasive measurement technique to characterize materials in terms of their permittivity based on a modified metamaterial unit-cell sensor. The sensor consists of a complementary split-ring resonator (C-SRR), but its fringe electric field is contained with a conductive shield to intensify the normal component of the electric field. It is shown that by tightly electromagnetically coupling opposite sides of the unit-cell sensor to the input/output microstrip feedlines, two distinct resonant modes are excited. Perturbation of the fundamental mode is exploited here for determining the permittivity of materials. The sensitivity of the modified metamaterial unit-cell sensor is enhanced four-fold by using it to construct a tri-composite split-ring resonator (TC-SRR). The measured results confirm that the proposed technique provides an accurate and inexpensive solution to determine the permittivity of materials.

Investigation of the JPA-Bandwidth Improvement in the Performance of the QTMS Radar.

Josephson parametric amplifier (JPA) engineering is a significant component in the quantum two-mode squeezed radar (QTMS) to enhance, for instance, radar performance and the detection range or bandwidth. We simulated a proposal of using engineered JPA (EJPA) to enhance the performance of a QTMS radar. We defined the signal-to-noise ratio (SNR) and detection range equations of the QTMS radar. The engineered JPA led to a remarkable improvement in the quantum radar performance, i.e., a large enhancement in SNR of about 6 dB more than the conventional QTMS radar (with respect to the latest version of the QTMS radar and not to the classical radar), a substantial improvement in the probability of detection through far fewer channels. The important point in this work was that we expressed the importance of choosing suitable detectors for the QTMS radars. Finally, we simulated the transmission of the signal to the target in the QTMS radar and obtained a huge increase in the QTMS radar range, up to 482 m in the current study.

Localization in Structured Environments with UWB Devices without Acceleration Measurements, and Velocity Estimation Using a Kalman-Bucy Filter.

In this work, a novel scheme for velocity and position estimation in a UWB range-based localization system is proposed. The suggested estimation strategy allows to overcome two main problems typically encountered in the localization systems. The first one is that it can be suitable for use in environments where the GPS signal is not present or where it might fail. The second one is that no accelerometer measurements are needed for the localization task. Moreover, to deal with the velocity estimation problem, a suitable Kalman-Bucy filter is designed and it is compared, experimentally, with a particle filter by showing the features of the two algorithms in order to be used in a localization context. Additionally, further experimental tests are carried out on a suitable developed test setup in order to confirm the goodness of the proposed approach.

Entanglement Robustness via Spatial Deformation of Identical Particle Wave Functions.

We address the problem of entanglement protection against surrounding noise by a procedure suitably exploiting spatial indistinguishability of identical subsystems. To this purpose, we take two initially separated and entangled identical qubits interacting with two independent noisy environments. Three typical models of environments are considered: amplitude damping channel, phase damping channel and depolarizing channel. After the interaction, we deform the wave functions of the two qubits to make them spatially overlap before performing spatially localized operations and classical communication (sLOCC) and eventually computing the entanglement of the resulting state. This way, we show that spatial indistinguishability of identical qubits can be utilized within the sLOCC operational framework to partially recover the quantum correlations spoiled by the environment. A general behavior emerges: the higher the spatial indistinguishability achieved via deformation, the larger the amount of recovered entanglement.

Advanced Monitoring Systems Based on Battery-Less Asset Tracking Modules Energized through RF Wireless Power Transfer.

Asset tracking involving accurate location and transportation data is highly suited to wireless sensor networks (WSNs) featuring battery-less nodes that can be deployed in virtually any environment and require little or no maintenance. In response to the growing demand for advanced battery-less sensor tag solutions, this article presents a system for identifying and monitoring the speeds of assets in a WSN with battery-less tags that receive all their operating energy through radio frequency (RF) wireless power transfer (WPT) architecture, and a unique measurement approach to generate time-domain speed readouts. The assessment includes performance characteristics and key features of a system on chip (SoC) purposely designed to power a node through RF WPT. The result is an innovative solution for RF to DC conversion able to address the principal difficulties associated with maximum power conversion efficiency (PCE) with sensitivity and vice versa, a strategy, and a design optimization model to indicate the number of readers required for reliable asset identification and speed measurement. Model validation is performed through specific tests. Experimental results demonstrating the viability of the proposed advanced monitoring system are provided.

A Novel Energy Harvester for Powering Small UAVs: Performance Analysis, Model Validation and Flight Results.

The proposed work aims at exploring and developing new strategies to extend mission parameters (measured as travel distance and mission duration (MD)) of a new class of unmanned vehicles, named Micro Air Vehicles (MAVs). In this paper, a new analytical model, identifying all factors, which determine the MAV power consumption, is presented. Starting from the new model, the design of a nanoarray energy harvester, based on plasmonics nano-antenna technology is proposed. The preliminary study was based on a 22,066,058 22,066,058 × 62,800-dipole rectenna array producing an output power level of 84.14 mW, and an energy value of 2572 J under a power density of 100 mW/cm² and a resonant frequency of 350 THz as input conditions. The preliminary analytical results show a possible recharge of an ultra-fast rechargeable battery on board of a MAV and an MD improvement of 16.30 min.

Strategies and Techniques for Powering Wireless Sensor Nodes through Energy Harvesting and Wireless Power Transfer.

The continuous development of internet of things (IoT) infrastructure and applications is paving the way for advanced and innovative ideas and solutions, some of which are pushing the limits of state-of-the-art technology. The increasing demand for Wireless Sensor Nodes (WSNs) able to collect and transmit data through wireless communication channels, while often positioned in locations that are difficult to access, is driving research into innovative solutions involving energy harvesting (EH) and wireless power transfer (WPT) to eventually allow battery-free sensor nodes. Due to the pervasiveness of radio frequency (RF) energy, RF EH and WPT are key technologies with the potential to power IoT devices and smart sensing architectures involving nodes that need to be wireless, maintenance free, and sufficiently low in cost to promote their use almost anywhere. This paper presents a state-of-the-art, ultra-low power 2.5 µ W highly integrated mixed signal system on chip (SoC), for multi-source energy harvesting and wireless power transfer. It introduces a novel architecture that integrates an ultra-low power intelligent power management, an RF to DC converter with very low power sensitivity and high power conversion efficiency (PCE), an Amplitude-Shift-Keying/Frequency-Shift-Keying (ASK/FSK) receiver and digital circuitry to achieve the advantage to cope, in a versatile way and with minimal use of external components, with the wide variety of energy sources and use cases. Diverse methods for powering Wireless Sensor Nodes through energy harvesting and wireless power transfer are implemented providing related system architectures and experimental results.

Quantum teleportation in Heisenberg chain with magnetic-field gradient under intrinsic decoherence.

One of the most appealing quantum communication protocols is quantum teleportation, which involves sharing entanglement between the sender and receiver of the quantum state. We address the two-qubit quantum teleportation based on the Heisenberg XYZ chain with a magnetic-field gradient affected by intrinsic decoherence. An atomic spin chain is primarily coupled to the linear gradient of the magnetic field in the x-direction, with the assumption that the magnetic field varies linearly with the position of the atom. By using the concepts of fidelity and average fidelity in the presence of the magnetic field gradient and under the effect of intrinsic decoherence in the current model, and considering the variables of the system, an improved quantum teleportation can be achieved. In addition, using the concept of remote quantum estimation, we examine remote quantum sensing in this article, which is very useful in quantum communication.

Progress in THz Rectifier Technology: Research and Perspectives.

Schottky diode (SD) has seen great improvements in the past few decades and, for many THz applications, it is the most useful device. However, the use and recycling of forms of energy such as solar energy and the infrared thermal radiation that the Earth continuously emits represent one of the most relevant and critical issues for this diode, which is unable to rectify signals above 5 THz. The goal is to develop highly efficient diodes capable of converting radiation from IR spectra to visible ones in direct current (DC). A set of performance criteria is investigated to select some of the most prominent materials required for developing innovative types of electrodes, but also a wide variety of insulator layers is required for the rectification process, which can affect the performance of the device. The current rectifying devices are here reviewed according to the defined performance criteria. The main aim of this review is to provide a wide overview of recent research progress, specific issues, performance, and future directions in THz rectifier technology based on quantum mechanical tunneling and asymmetric structure.

Engineering in-plane mechanics of electrospun polyurethane scaffolds for cardiovascular tissue applications.

Effective cardiovascular tissue surrogates require high control of scaffold structural and mechanical features to match native tissue properties, which are dependent on tissue-specific mechanics, function heterogenicity, and morphology. Bridging scaffold processing variables with native tissue properties is recognized as a priority for advancing biomechanical performance of biomedical materials and, when translated to the clinical practice, their efficacy. Accordingly, this study selected electrospinning on a rotating cylindrical target as an apparatus of broad application and mapped the relationship between key processing variables and scaffold mechanics and structure. This information was combined with mechanical anisotropy ranges of interest for the three main categories of tissue surrogated in cardiovascular tissue engineering: heart valve leaflets, ventricle wall, and large diameter blood vessels. Specifically, three processing variables have been considered: the rotational velocity and the rastering velocity of the mandrel and the dry (single nozzle - polymer only) vs wet (double nozzle - polymer plus phosphate buffer saline solution) fabrication configuration. While the dry configuration is generally utilized to obtain micro-fiber based polymeric mats, the wet fabrication is representative of processing conditions utilized to incorporate cells, growth factors, or micro-particles within the fibrous scaffold matrix. Dry and wet processed electrospun mats were fabricated with tangential and rastering velocities within the 0.3-9.0 m/s and 0.16-8 cm/s range respectively. Biaxial mechanics, fiber network, and pore micro-architectures were measured for each combination of velocities and for each fabrication modality (dry and wet). Results allowed identification of the precise combination of rotational and rastering velocities, for both dry and wet conditions, that is able to recapitulate the native cardiovascular tissue anisotropy ratio. By adopting a simple and broadly utilized electrospinning layout, this study is meant to provide a repeatable and easy to access methodology to improve biomimicry of the in plane-mechanics of heart valve leaflets, ventricular wall, and large diameter blood vessels.

High gain/bandwidth off-chip antenna loaded with metamaterial unit-cell impedance matching circuit for sub-terahertz near-field electronic systems.

An innovative off-chip antenna (OCA) is presented that exhibits high gain and efficiency performance at the terahertz (THz) band and has a wide operational bandwidth. The proposed OCA is implemented on stacked silicon layers and consists of an open circuit meandering line. It is shown that by loading the antenna with an array of subwavelength circular dielectric slots and terminating it with a metamaterial unit cell, its impedance bandwidth is enhanced by a factor of two and its gain on average by about 4 dB. Unlike conventional antennas, where the energy is dissipated in a resistive load, the technique proposed here significantly reduces losses. The antenna is excited from underneath the antenna by coupling RF energy from an open-circuited feedline through a slot in the ground-plane of the middle substrate layer. The feedline is shielded with another substrate layer which has a ground-plane on its opposite surface to mitigate the influence of the structure on which the antenna is mounted. The antenna has the dimensions 12.3 × 4.5 × 0.905 mm3 and operates across the 0.137-0.158 THz band corresponding to a fractional bandwidth of 14.23%. Over this frequency range the average measured gain and efficiency are 8.6 dBi and 77%, respectively. These characteristics makes the proposed antenna suitable for integration in sub-terahertz near-field electronic systems such as radio frequency identification (RFID) devices with high spatial resolution.

Fluorescent Biosensors Based on Silicon Nanowires.

Nanostructures are arising as novel biosensing platforms promising to surpass current performance in terms of sensitivity, selectivity, and affordability of standard approaches. However, for several nanosensors, the material and synthesis used make the industrial transfer of such technologies complex. Silicon nanowires (NWs) are compatible with Si-based flat architecture fabrication and arise as a hopeful solution to couple their interesting physical properties and surface-to-volume ratio to an easy commercial transfer. Among all the transduction methods, fluorescent probes and sensors emerge as some of the most used approaches thanks to their easy data interpretation, measure affordability, and real-time in situ analysis. In fluorescent sensors, Si NWs are employed as substrate and coupled with several fluorophores, NWs can be used as quenchers in stem-loop configuration, and have recently been used for direct fluorescent sensing. In this review, an overview on fluorescent sensors based on Si NWs is presented, analyzing the literature of the field and highlighting the advantages and drawbacks for each strategy.

Ultrathin Silicon Nanowires for Optical and Electrical Nitrogen Dioxide Detection.

The ever-stronger attention paid to enhancing safety in the workplace has led to novel sensor development and improvement. Despite the technological progress, nanostructured sensors are not being commercially transferred due to expensive and non-microelectronic compatible materials and processing approaches. In this paper, the realization of a cost-effective sensor based on ultrathin silicon nanowires (Si NWs) for the detection of nitrogen dioxide (NO2) is reported. A modification of the metal-assisted chemical etching method allows light-emitting silicon nanowires to be obtained through a fast, low-cost, and industrially compatible approach. NO2 is a well-known dangerous gas that, even with a small concentration of 3 ppm, represents a serious hazard for human health. We exploit the particular optical and electrical properties of these Si NWs to reveal low NO2 concentrations through their photoluminescence (PL) and resistance variations reaching 2 ppm of NO2. Indeed, these Si NWs offer a fast response and reversibility with both electrical and optical transductions. Despite the macro contacts affecting the electrical transduction, the sensing performances are of high interest for further developments. These promising performances coupled with the scalable Si NW synthesis could unfold opportunities for smaller sized and better performing sensors reaching the market for environmental monitoring.

High-Mobility, Wet-Transferred Graphene Grown by Chemical Vapor Deposition.

We report high room-temperature mobility in single-layer graphene grown by chemical vapor deposition (CVD) after wet transfer on SiO2 and hexagonal boron nitride (hBN) encapsulation. By removing contaminations, trapped at the interfaces between single-crystal graphene and hBN, we achieve mobilities up to ∼70000 cm2 V-1 s-1 at room temperature and ∼120 000 cm2 V-1 s-1 at 9K. These are more than twice those of previous wet-transferred graphene and comparable to samples prepared by dry transfer. We also investigate the combined approach of thermal annealing and encapsulation in polycrystalline graphene, achieving room-temperature mobilities of ∼30 000 cm2 V-1 s-1. These results show that, with appropriate encapsulation and cleaning, room-temperature mobilities well above 10 000 cm2 V-1 s-1 can be obtained in samples grown by CVD and transferred using a conventional, easily scalable PMMA-based wet approach.