Valorization of Kraft Lignins from Different Poplar Genotypes as Vegetable Oil Structuring Agents via Electrospinning for Biolubricant Applications.

This work explores the use of Kraft lignins sourced from different poplar genotypes (Populus alba L. "PO-10-10-20" and Populus × canadensis "Ballotino") isolated by selective acid precipitation (at pHs 5 and 2.5) to produce electrospun nanostructures that can be further employed for structuring vegetable oils. This approach offers a new avenue for converting these waste materials into high-value-added ingredients of eco-friendly structured lubricants. Electrospinning of poplar Kraft lignin (PKL)/cellulose acetate (CA) solutions yielded homogeneous beaded nanofiber mats that were able to generate stable dispersions when they were blended with different vegetable oils (castor, soybean, and high-oleic sunflower oils). Electrospun PKL/CA nanofiber mats with larger average fiber diameters were achieved using the lignins isolated at pH 5. Dispersions of PKL/CA nanofibers in vegetable oils presented gel-like viscoelastic characteristics and shear-thinning flow behavior, which slightly differ depending on the nanofiber morphological properties and can be tuned by selecting the poplar lignin genotype and precipitation pH. The rheological properties and tribological performance of PKL/CA nanofibers suitably dispersed in vegetable oils were found to be comparable to those obtained for conventional lubricating greases. Additionally, lignin nanofibers confer suitable oxidative stability to the ultimate formulations to different extents depending on the vegetable oil used.

Bioethanol lignin-rich residue from olive stones for electrospun nanostructures development and castor oil structuring.

This work describes the chemical and structural characterization of a lignin-rich residue from the bioethanol production of olive stones and its use for nanostructures development by electrospinning and castor oil structuring. The olive stones were treated by sequential acid/steam explosion pretreatment, further pre-saccharification using a hydrolytic enzyme, and simultaneous saccharification and fermentation (PSSF). The chemical composition of olive stone lignin-rich residue (OSL) was evaluated by standard analytical methods, showing a high lignin content (81.3 %). Moreover, the structural properties were determined by Fourier-transform infrared spectroscopy, nuclear magnetic resonance, and size exclusion chromatography. OSL showed a predominance of ß-ß' resinol, followed by ß-O-4' alkyl aryl ethers and ß-5' phenylcoumaran substructures, high molecular weight, and low S/G ratio. Subsequently, electrospun nanostructures were obtained from solutions containing 20 wt% OSL and cellulose triacetate with variable weight ratios in N, N-Dimethylformamide/Acetone blends and characterized by scanning electron microscopy. Their morphologies were highly dependent on the rheological properties of polymeric solutions. Gel-like dispersions can be obtained by dispersing the electrospun OSL/CT bead nanofibers and uniform nanofiber mats in castor oil. The rheological properties were influenced by the membrane concentration and the OSL:CT weight ratio, as well as the morphology of the electrospun nanostructures.

Exploring Cellulose Triacetate Nanofibers as Sustainable Structuring Agent for Castor Oil: Formulation Design and Rheological Insights.

Developing gelled environmentally friendly dispersions in oil media is a hot topic for many applications. This study aimed to investigate the production of electrospun cellulose triacetate (CTA) nanofibers and to explore their potential application as a thickening agent for castor oil. The key factors in the electrospinning process, including the intrinsic properties of CTA solutions in methylene chloride (DCM)/ethanol (EtOH), such us the shear viscosity, surface tension, and electrical conductivity, were systematically studied. The impact of the CTA fiber concentration and the ratio of DCM/EtOH on the rheological properties of the gel-like dispersions in castor oil was then investigated. It was found that dispersions with a non-Newtonian response and above a critical concentration (5 wt.%), corresponding to approximately 2-2.5 times the entanglement concentration, are required to produce defect-free nanofibers. The average fiber diameter increased with CTA concentration. Further, the morphology and texture of the electrospun nanofibers are influenced by the ratio of solvents used. The rheological properties of dispersions are strongly influenced by the concentration and surface properties of nanofibers, such as their smooth or porous textures, which allow their modulation. Compared to other commonly used thickeners, such as synthetic polymers and metal soaps, CTA electrospun nanofibers have a much higher oil structuring capacity. This work illustrated the potential of using CTA nanofibers as the foundation for fabricating gel-like dispersions in oil media, and thus exerting hierarchical control of rheological properties through the use of a nanoscale fabrication technique.

Assessment of the Tribological Performance of Electrospun Lignin Nanofibrous Web-Thickened Bio-Based Greases in a Nanotribometer.

The tribological performance of novel bio-based lubricating greases thickened with electrospun lignin nanostructures was investigated in a nanotribometer using a steel-steel ball-on-disc configuration. The impact of electrospun nanofibrous network morphology on friction and wear is explored in this work. Different lignin nanostructures were obtained with electrospinning using ethylcellulose or PVP as co-spinning polymers and subsequently used as thickeners in castor oil at concentrations of 10-30% wt. Friction and wear generally increased with thickener concentration. However, friction and wear decreased when using homogeneous bead-free nanofiber mats (with higher fiber diameter and lower porosity) rather than nanostructures dominated by the presence of particles or beaded fibers, which was favored by reducing the lignin:co-spinning polymer ratio.

Study of CdS/CdS Nanoparticles Thin Films Deposited by Soft Chemistry for Optoelectronic Applications.

Chalcogenides semiconductors are currently being studied as active layers in the development of electronic devices in the field of applied technology. In the present paper, cadmium sulfide (CdS) thin films containing nanoparticles of the same material as the active layer were produced and analyzed for their application in fabricating optoelectronic devices. CdS thin films and CdS nanoparticles were obtained via soft chemistry at low temperatures. The CdS thin film was deposited via chemical bath deposition (CBD); the CdS nanoparticles were synthesized via the precipitation method. The construction of a homojunction was completed by incorporating CdS nanoparticles on CdS thin films deposited via CBD. CdS nanoparticles were deposited using the spin coating technique, and the effect of thermal annealing on the deposited films was investigated. In the modified thin films with nanoparticles, a transmittance of about 70% and a band gap between 2.12 eV and 2.35 eV were obtained. The two characteristic phonons of the CdS were observed via Raman spectroscopy, and the CdS thin films/CdS nanoparticles showed a hexagonal and cubic crystalline structure with average crystallite size of 21.3-28.4 nm, where hexagonal is the most stable for optoelectronic applications, with roughness less than 5 nm, indicating that CdS is relatively smooth, uniform and highly compact. In addition, the characteristic curves of current-voltage for as-deposited and annealed thin films showed that the metal-CdS with the CdS nanoparticle interface exhibits ohmic behavior.

Impact of the Morphology of Electrospun Lignin/Ethylcellulose Nanostructures on Their Capacity to Thicken Castor Oil.

This study reports on a novel strategy for manufacturing thickened gel-like castor oil formulations by dispersing electrospun lignin/ethylcellulose nanostructures. These thickened formulations were rheologically and tribologically evaluated with the aim of being proposed as alternative ecofriendly lubricating greases. Low-sulfonate kraft lignin (LSL) and ethylcellulose (EC) were dissolved in a DMAc:THF mixture at different concentrations (8, 10, and 15 wt.%) and LSL:EC ratios (50:50, 70:30, and 90:10) and subjected to electrospinning. The resulting electrospun nanostructures were morphologically characterized. EC acting as the cospinning polymer improved both LSL spinnability and the oil structuring ability. Solutions with a high lignin content achieved microsized particles connected by fibrils, whereas solutions with a high EC content (50:50 ratio) and LSL/EC total concentration (10 and 15 wt.%) yielded beaded or bead-free nanofibers, due to enhanced extensional viscoelastic properties and nonNewtonian characteristics. The gel-like properties of electrospun nanostructure dispersions in castor oil were strengthened with the nanostructure concentration and the EC:LSL ratio, as a result of the formation of a more interconnected fiber network. The oleodispersions studied exhibited a satisfactory frictional response in a tribological contact, with friction coefficient values that were comparable to those achieved with traditional lithium-lubricating greases.

Impact of Vegetable Oil Type on the Rheological and Tribological Behavior of Montmorillonite-Based Oleogels.

We formulated and characterized oleogels based on montmorillonite clay and vegetable oils that could serve as eco-friendly semi-solid lubricants. In particular, we studied the influence of the physical-chemical properties of olive, castor, soybean, linseed, and sunflower oils on the rheological, chemical, thermal, and tribological properties of the semi-solid lubricants. We prepared the oleogels via the highly intensive mixing of vegetable oils with clay at a concentration of 30 wt.%. The oleogels exhibited shear-thinning, thixotropy, structural recovery, and gel-like behavior commonly related to that of a three-dimensional network. The results were corroborated via XRD measurements showing the presence of intercalated nanoclay structures well-dispersed in the vegetable oil. Empirical correlations between the content of saturated (SFAs), unsaturated (UFAs), mono-unsaturated (MUFAs) and poly-unsaturated (PUFAs) fatty acids and the plateau modulus of the aerogels were found. From these experimental results, we can conclude that the fatty acid profile of the vegetable oils exerts an important influence on the rheological and tribological properties of resulting clay and vegetable oil oleogels.

Electrospun lignin-PVP nanofibers and their ability for structuring oil.

This work explores the electrospinnability of low-sulfonate Kraft lignin (LSL)/polyvinylpyrrolidone (PVP) solutions in N,N-dimethylformamide (DMF) and the ability of the different micro- and nano-architectures generated to structure castor oil. LSL/PVP solutions were prepared at different concentrations (8-15 wt%) and LSL:PVP ratios (90:10-0:100) and physico-chemically and rheologically characterized. The morphology of electrospun nanostructures mainly depends on the rheological properties of the solution. Electrosprayed nanoparticles or micro-sized particles connected by thin filaments were obtained from solutions with low LSL/PVP concentrations and/or high LSL:PVP ratios, whereas beaded or bead-free nanofibers were produced by increasing concentration and/or decreasing LSL:PVP ratio, due to enhanced extensional viscoelastic properties and non-Newtonian characteristics. Electrospun LSL/PVP nanofibers are able to form oleogels by simply dispersing them into castor oil at concentrations between 10 and 30 wt%. The rheological properties of the oleogels may be tailored by modifying the LSL:PVP ratio and nanofibers content. The potential application of these oleogels as bio-based lubricants was also explored in a tribological cell. Satisfactory friction and wear results are achieved when using oleogels structured by nanofibers mats with enhanced gel-like properties as lubricants. Overall, electrospinning of lignin/PVP solutions can be proposed as a simple and effective method to produce nanofibers for oil structuring.

Electrohydrodynamic Processing of PVP-Doped Kraft Lignin Micro- and Nano-Structures and Application of Electrospun Nanofiber Templates to Produce Oleogels.

The present work focuses on the development of lignin micro- and nano-structures obtained by means of electrohydrodynamic techniques aimed to be potentially applicable as thickening or structuring agents in vegetable oils. The micro- and nano-structures used were mainly composed of eucalyptus kraft lignin (EKL), which were doped to some extent with polyvinylpyrrolidone (PVP). EKL/PVP solutions were prepared at different concentrations (10-40 wt.%) and EKL:PVP ratios (95:5-100:0) in N, N-dimethylformamide (DMF) and further physico-chemically and rheologically characterized. Electrosprayed micro-sized particles were obtained from solutions with low EKL/PVP concentrations (10 and 20 wt.%) and/or high EKL:PVP ratios, whereas beaded nanofiber mats were produced by increasing the solution concentration and/or decreasing EKL:PVP ratio, as a consequence of improved extensional viscoelastic properties. EKL/PVP electrospun nanofibers were able to form oleogels by simply dispersing them into castor oil at nanofiber concentrations higher than 15 wt.%. The rheological properties of these oleogels were assessed by means of small-amplitude oscillatory shear (SAOS) and viscous flow tests. The values of SAOS functions and viscosity depended on both the nanofiber concentration and the morphology of nanofiber templates and resemble those exhibited by commercial lubricating greases made from traditional metallic soaps and mineral oils.