Crystalline Structure and Thermal Stability of an Unknown ZIF-L300 Phase.

In recent years, the synthesis, crystalline structure, and applications of zeolite imidazole frameworks (ZIFs) have attracted extensive attention. Since the ZIF-L phase was synthesized, a new phase was observed during the heating process, but its crystal structure is unknown. The unknown new phase, which was named ZIF-L300 in this study, was confirmed again. In this study, the X-ray powder diffraction technique and Rietveld refinement were used to solve the crystalline structure of the unknown ZIF-L300 phase. The results demonstrate that ZIF-L300 has the same chemical formula (ZnC8N4H10) as in ZIF-8 and belongs to a hexagonal structure with a space group of P61. The lattice parameters have been determined as follows: a = b = 8.708(7) Å, c = 24.195(19) Å, α = ß = 90°, and γ = 120°. The X-ray absorption fine structure (XAFS) technique was also used to extract the local atomic structures. The in situ X-ray diffraction (XRD) technique was used to monitor the structural evolution of the as-prepared ZIF-L in a temperature range from room temperature to 600 °C. The results show that the sample experiences a change process from the initial ZIF-L orthorhombic phase (<210 °C), to the ZIF-L300 hexagonal phase (∼300 °C), then to an amorphous phase (∼390 °C), and finally to a zincite ZnO phase (>420 °C). These sorts of structural information are helpful to the application of ZIF materials and enrich the knowledge of the thermal stability of ZIF materials.

Efficient Electrocatalytic Reduction of CO2 to Ethane over Nitrogen-Doped Fe2O3.

Non-copper electrocatalysts are seldom reported to generate C2+ products, and the efficiency over these catalysts is low. In this work, we report a nitrogen-doped γ-Fe2O3 (xFe2O3-N@CN) electrocatalyst, which yield C2H6 as the major product in an H-cell. At -2.0 V vs Ag/Ag+, the Faradaic efficiency (FE) for ethane reaches 42% with a current density of 32 mA cm-2. This is the first report about selective CO2 reduction to ethane (C2H6) over an iron-based catalyst. The results showed that the catalyst possessing FeO1.5-nNn sites enriched with oxygen vacancies was beneficial for the stabilization of *COOH intermediates. The exposure of two adjacent surfaces of Fe atoms was conducive to lowering the energy barrier for C-C coupling over FeO1.5-nNn sites, facilitating the generation of C2H6. This work provides a strategy for the design of a novel iron-based catalyst with tunable local coordination and electronic structures for converting CO2 into C2 products in the CO2RR.

A polycrystalline diamond micro-detector for X-ray absorption fine-structure measurements.

The microminiaturization of detectors used to record the intensity of X-ray beams is very favorable for combined X-ray experimental techniques. In this paper, chemical-vapor-deposited (CVD) polycrystalline diamond film was used to fabricate a micro-detector owing to its well controlled size, good thermostability, and appropriate conductivity. The preparation process and the main components of the CVD diamond micro-detector are described. The external dimensions of the packaged CVD diamond micro-detector are 15 mm × 7.8 mm × 5.8 mm. To demonstrate the performance of the detector, K-edge X-ray absorption fine-structure (XAFS) spectra of Cr, Fe, Cu, and Se foils were collected using the CVD diamond micro-detector and routine ion chamber. These XAFS measurements were performed at beamline 1W2B of Beijing Synchrotron Radiation Facility, covering an energy range from 5.5 to 13.5 keV. By comparison, it can be seen that the CVD diamond micro-detector shows a more excellent performance than the routine ion-chamber in recording these XAFS spectra. The successful application of the CVD diamond micro-detector in XAFS measurements shows its feasibility in recording X-ray intensity.

Hydrothermal Synthesis and Structures of Unknown Intermediate Phase Zn(HCO3)2·H2O Nanoflakes and Final ZnO Nanorods.

The formation mechanism of nanoparticles is of great significance for the controllable synthesis, structural design, and performance optimization of nanomaterials. In this paper, an economical hydrothermal method was used to synthesize zinc oxide (ZnO) nanorods. X-ray diffraction, X-ray absorption fine structure, and small-angle X-ray scattering techniques were used to probe the structural changes. Scanning electron microscopy and high-resolution transmission electron microscopy were used to observe the morphologies of the products. A self-designed in situ temperature-pressure sample cell was used to control the hydrothermal conditions. The results demonstrate that an unknown intermediate phase, Zn(HCO3)2·H2O, was first formed at 50 °C, having a morphology of nanoflakes with a average thickness of about 35 nm. The intermediate phase Zn(HCO3)2·H2O was determined to have a monoclinic structure with space group P1211 and the following lattice parameters: a = 11.567 Å, b = 3.410 Å, c = 5.358 Å, ß = 96.0011°, and Z = 2. After a hydrothermal temperature of 140 °C, CO2 and H2O were evaporated from the Zn(HCO3)2·H2O intermediate product and the ZnO nanorods with a wurtzite structure were formed. The final ZnO nanorods have an average diameter of about 45 nm and an average length of about 2 µm. The axial direction of the ZnO nanorods is the [001] crystallographic direction. By virtue of understanding the formation mechanism, this work is helpful for the controllable synthesis of ZnO nanoparticles.

The distinct effects of two imidazolium-based ionic liquids, [C4mim][OAc] and [C6mim][OAc], on the phase behaviours of DPPC.

Ionic liquids (ILs) are potential green solvents with very broad application prospects. Their toxicity and other biological effects are largely related to their hydrophobic properties. In this work, the effects of two imidazolium-based ILs with either a butyl or a hexyl chain, [C4mim][OAc] or [C6mim][OAc], on the phase behaviours of a representative phospholipid, dipalmitoylphosphatidylcholine (DPPC), were examined using synchrotron small- and wide-angle X-ray scattering and differential scanning calorimetry techniques. A series of samples with a lipid : IL molar ratio ranging from 1 : 0 to 1 : 4/1 : 5 were prepared as aqueous dispersions in the form of multi-lamellar vesicles. The two ILs were found to have distinct effects on the phase behaviours of DPPC. For [C4mim][OAc], its effect is very limited. In contrast, for [C6mim][OAc], it could eliminate the pre-transition of DPPC, markedly affect the main phase transition of the lipid, and insert into the DPPC bilayer at gel state to form an interdigitated gel phase. The findings increased our understanding on the biological effects of imidazolium-based ILs and might shed light on the design of novel IL-based antimicrobials.

Highly Electrocatalytic Ethylene Production from CO2 on Nanodefective Cu Nanosheets.

The electrochemical synthesis of chemicals from carbon dioxide, which is an easily available and renewable carbon resource, is of great importance. However, to achieve high product selectivity for desirable C2 products like ethylene is a big challenge. Here we design Cu nanosheets with nanoscaled defects (2-14 nm) for the electrochemical production of ethylene from carbon dioxide. A high ethylene Faradaic efficiency of 83.2% is achieved. It is proved that the nanoscaled defects can enrich the reaction intermediates and hydroxyl ions on the electrocatalyst, thus promoting C-C coupling for ethylene formation.

Actinide Separation Inspired by Self-Assembled Metal-Polyphenolic Nanocages.

The separation of actinides has a vital place in nuclear fuel reprocessing, recovery of radionuclides, and remediation of environmental contamination. Here we propose a new paradigm of nanocluster-based actinide separation, namely, nanoextraction, that can achieve efficient sequestration of uranium in an unprecedented form of giant coordination nanocages using a cone-shaped macrocyclic pyrogallol[4]arene as the extractant. The U24-based hexameric pyrogallol[4]arene nanocages with distinctive [U2(PG)2] binuclear units (PG = pyrogallol) that rapidly assembled in situ in monophasic solvent were identified by single-crystal X-ray diffraction, MALDI-TOF mass spectrometry, NMR spectroscopy, and small-angle X-ray and neutron scattering. Comprehensive biphasic extraction studies showed that this novel separation strategy has enticing advantages such as fast kinetics, high efficiency, and good selectivity over lanthanides, thereby demonstrating its potential for efficient separation of actinide ions.

Temperature-driven directional coalescence of silver nanoparticles.

Silver nanoparticles were synthesized with a chemical reduction method in the presence of polyvinylpyrrolidone as stabilizing agent. The thermal stability behavior of the silver nanoparticles was studied in the temperature range from 25 to 700°C. Thermal gravimetric analysis was used to measure the weight loss of the silver nanoparticles. Scanning electron microscopy and high-resolution transmission electron microscopy were used to observe the morphology and the change in shape of the silver nanoparticles. In situ temperature-dependent small-angle X-ray scattering was used to detect the increase in particle size with temperature. In situ temperature-dependent X-ray diffraction was used to characterize the increase in nanocrystal size and the thermal expansion coefficient. The results demonstrate that sequential slow and fast Ostward ripening are the main methods of nanoparticle growth at lower temperatures (<500°C), whereas successive random and directional coalescences are the main methods of nanoparticle growth at higher temperatures (>500°C). A four-stage model can be used to describe the whole sintering process. The thermal expansion coefficient (2.8 × 10(-5) K(-1)) of silver nanoparticles is about 30% larger than that of bulk silver. To our knowledge, the temperature-driven directional coalescence of silver nanocrystals is reported for the first time. Two possible mechanisms of directional coalescence have been proposed. This study is of importance not only in terms of its fundamental academic interest but also in terms of the thermal stability of silver nanoparticles.

Water-in-Supercritical CO2 Microemulsion Stabilized by a Metal Complex.

Herein we propose for the first time the utilization of a metal complex for forming water-in-supercritical CO2 (scCO2 ) microemulsions. The water solubility in the metal-complex-stabilized microemulsion is significantly improved compared with the conventional water-in-scCO2 microemulsions stabilized by hydrocarbons. Such a microemulsion provides a promising route for the in situ CO2 reduction catalyzed by a metal complex at the water/scCO2 interface.

Semi-crystalline polymethylene-b-poly(acrylic acid) diblock copolymers: aggregation behavior, confined crystallization and controlled growth of semicrystalline micelles from dilute DMF solution.

In this paper, we have systematically investigated the aggregation behavior, confined crystallization and controlled growth of a novel polyolefin analogue-containing block copolymers (BCPs), i.e., polymethylene-b-poly(acrylic acid) diblock copolymers (PM-b-PAA). On cooling from a homogenous DMF solution at 80 °C, PM-b-PAA was found to crystallize and aggregate with well-defined disk-like micelles. The aggregate behavior and in-plane morphology of PM-b-PAA could be easily controlled by modifying the block ratio, solution pH and solvent composition (DMF-water), by manipulating the crystallization of PM block and the stretching degree of solvated PAA corona. Further investigation of the crystalline feature of PM-b-PAA indicated that the crystallization of PM was retarded by tethered amorphous PAA segments. The crystalline micelle could construct a nano-confined environment with PM folding as the core into a thickness of the mono-layered polyethylene. Finally, when cultured in dilute DMF solution at 50 °C, the initial crystalline micelles, being as self-seeds, could follow a living growth mechanism and develop into single crystals, with well-defined lozenge-shaped morphology.

One-step synthesis of highly efficient nanocatalysts on the supports with hierarchical pores using porous ionic liquid-water gel.

Stable porous ionic liquid-water gel induced by inorganic salts was created for the first time. The porous gel was used to develop a one-step method to synthesize supported metal nanocatalysts. Au/SiO2, Ru/SiO2, Pd/Cu(2-pymo)2 metal-organic framework (Cu-MOF), and Au/polyacrylamide (PAM) were synthesized, in which the supports had hierarchical meso- and macropores, the size of the metal nanocatalysts could be very small (<1 nm), and the size distribution was very narrow even when the metal loading amount was as high as 8 wt %. The catalysts were extremely active, selective, and stable for oxidative esterification of benzyl alcohol to methyl benzoate, benzene hydrogenation to cyclohexane, and oxidation of benzyl alcohol to benzaldehyde because they combined the advantages of the nanocatalysts of small size and hierarchical porosity of the supports. In addition, this method is very simple.

A concise synthesis of benzimidazoles via the microwave-assisted one-pot batch reaction of amino acids up to a 10-g scale.

An efficient method for the synthesis of aminomethyl benzimidazoles is developed by using a one-pot batch reaction between amino acids and o-phenylenediamines. This reaction proceeds smoothly in an unmodified household microwave oven, even though scale-up is to 10 g. A desirable method for the quick synthesis of benzimidazoles, which are used as a kind of important intermediates in drug synthesis, is provided by the scale-up utilization of amino acid resource.

Benzimidazole derivatives: selective fluorescent chemosensors for the picogram detection of picric acid.

1,3,5-Tri(1H-benzo[d]imidazol-2-yl)benzene derivatives, as a new kind of fluorescent chemosensor for the detection of nitroaromatic explosives, are designed and synthesized by simple N-hydrocarbylation. Among 16 obtained compounds, compound 4g has the best capability for detection of picric acid (PA), having good selectivity and high sensitivity. The detection of PA with 4g solution-coated paper strips at the picogram level is developed. A simple, portable, and low-cost method is provided for detecting PA in solution and contact mode.

Docking and molecular dynamics studies of the binding between Peloruside A and tubulin.

The molecular docking, MD simulation and binding free energy calculation were performed to explore the probable binding modes between PLA and tubulin. Through docking study, three possible binding sites for PLA were speculated as follows: the taxane site, the alternative site and a new site in α-tubulin. Then, 12.0 ns MD simulations show that these binding modes predicted by docking have been changed more or less, whereas the MD simulations offer more reliable binding details. The MM-PBSA binding free-energy calculations reasonably identify that the taxane site is the most favorable binding site of PLA and the alternative site is the secondary one, which can be used to explain some experimental facts. These studies theoretically resolve the priority of binding sites for PLA and offer the reliable binding modes between PLA and tubulin, and thus help to understanding the action mechanism for this kind of inhibitor.

High-pressure study of a 3d-4f heterometallic CuEu-organic skeleton.

We prepared a 3d-4f heterobimetallic CuEu-organic framework NBU-8 with a density of 1921 kg m-3 belonging to the family of dense packing materials (dense metal-organic frameworks or MOFs). This MOF material was prepared from 4-(pyrimidin-5-yl)benzoic acid (HPBA) with a bifunctional ligand site as a tripodal ligand and Cu2+ and Eu3+ as the metal centres; the molecular formula is Cu3Eu2(PBA)6(NO3)6·H2O. This material is a very promising dimethylformamide (DMF) molecular chemical sensor. Systematic high-pressure studies of NBU-8 were carried out by powder X-ray diffraction, high-pressure X-ray diffraction and molecular dynamics simulation. The high-pressure experiment shows that the (006) diffraction peak of the crystal structure moves toward a low angle with increasing pressure, accompanied by the phenomenon that the d-spacing increases, and as the pressure increases, the (10-2) diffraction peak moves to a higher angle, the amplitude of the d-spacing is significantly reduced and finally merges with the (006) diffraction peak into one peak. The amplitude of the d-spacing is significantly reduced, indicating that NBU-8 compresses and deforms along the a-axis direction when subjected to uniform pressure. This is caused by tilting of the ligands to become more vertical along the c direction, leading to its expansion. This allows greater contraction along the a direction. We also carried out a Rietveld structure refinement and a Birch-Murnaghan solid-state equation fitting for the high-pressure experimental results. We calculated the bulk modulus of the material to be 45.68 GPa, which is consistent with the calculated results. The framework is among the most rigid MOFs reported to date, exceeding that of Cu-BTC. Molecular dynamics simulations estimated that the mechanical energy absorbed by the system when pressurized to 5.128 GPa was 249.261 kcal mol-1. The present work will provide fresh ideas for the study of mechanical energy in other materials.

Recent advances in battery characterization using in situ XAFS, SAXS, XRD, and their combining techniques: From single scale to multiscale structure detection.

Revealing and clarifying the chemical reaction processes and mechanisms inside the batteries will bring a great help to the controllable preparation and performance modulation of batteries. Advanced characterization techniques based on synchrotron radiation (SR) have accelerated the development of various batteries over the past decade. In situ SR techniques have been widely used in the study of electrochemical reactions and mechanisms due to their excellent characteristics. Herein, the three most wide and important synchrotron radiation techniques used in battery research were systematically reviewed, namely X-ray absorption fine structure (XAFS) spectroscopy, small-angle X-ray scattering (SAXS), and X-ray diffraction (XRD). Special attention is paid to how these characterization techniques are used to understand the reaction mechanism of batteries and improve the practical characteristics of batteries. Moreover, the in situ combining techniques advance the acquisition of single scale structure information to the simultaneous characterization of multiscale structures, which will bring a new perspective to the research of batteries. Finally, the challenges and future opportunities of SR techniques for battery research are featured based on their current development.

Shape evolution with temperature of a thermotolerant protein (PeaT1) in solution detected by small angle X-ray scattering.

The protein elicitor from Alternaria tenuissima (PeaT1) presented excellent thermotolerance and potential application in agriculture as a pesticide. Previous synchrotron radiation circular dichroism study demonstrated that the secondary structures in PeaT1 protein are reversible with temperature change. To further clarify the mechanism of its thermotolerance, synchrotron radiation small angle x-ray scattering (SAXS) technique was used to study the shape change of PeaT1 protein with temperature in this article. Ab initio structure restorations based on the SAXS data revealed that PeaT1 protein has a prolate shape with a P2 symmetry axis along the prolate anisometric direction. With temperature increase, a gooseneck vase-like (25°C), to jug-like (55°C), then to oval (85°C) shape change can be found, and these shape changes are also approximately reversible with temperature decrease. PeaT1 protein contains two homogenous molecules, and each of them consists of F, NAC, T, and UBA domains. The structures of the four domains were predicted. Simulated annealing algorithm was used to superimpose the domain structures onto the SAXS shapes. It was found that all the structural domains have position rotation and translation with temperature change, but the NAC domains are relatively stable, playing a role of frame. This shape change information provides clues for further exploring its biological function and application.

Shape and size controlled synthesis of MOF nanocrystals with the assistance of ionic liquid mircoemulsions.

In this work, the La-metal-organic frameworks (La-MOFs) were synthesized using lanthanum(III) nitrate and 1,3,5-benzenetricarboxylic acid (BTC) in H2O-in-1-butyl-3-methylimidazolium hexafluorophosphate (bmimPF6), bmimPF6-in-water, and the bicontinuous microemulsions stabilized by surfactant TX-100. The MOFs prepared were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), powder X-ray diffraction (XRD), thermal gravimetric analysis (TGA), and FT-IR methods, and the microstructures of the microemulsions in the H2O/bmimPF6/TX-100 system were studied by small-angle X-ray scattering (SXAS) technique. It was shown that the dispersed droplets in the water-in-bmimPF6, bicontinuous and bmimPF6-in-water microemulsions were spherical, lamellar, and cylindrical, respectively. The shapes of the La-MOFs synthesized were similar to that of the droplets in the corresponding microemulsions. This indicated that the morphology of MOFs could be controlled by the microstructures of the microemulsions. On the basis of the systematic experimental results, the mechanism for controlling the morphology of the MOFs was proposed.

Structural change of human hair induced by mercury exposure.

Mercury is one of the most hazardous pollutants in the environment. In this paper, the structural change of human hair induced by mercury exposure was studied. Human hair samples were, respectively, collected from the normal Beijing area and the Hg-contaminated Wanshan area of the Guizhou Province, China. Inductively coupled plasma mass spectroscopy was used to detect the element contents. A small angle X-ray scattering technique was used to probe the structural change. Three reflections with 8.8, 6.7, and 4.5 nm spacing were compared between the normal and the Hg-contaminated hair samples. The results confirm that the 4.5 nm reflection is from the ordered fibrillar structure of glycosaminoglycan (GAG) in proteoglycan (PG) that composes the matrix around the intermediate filaments. The increase of Ca content makes the regular oriented fibrillar structure of GAG transform to a random oriented one, broadening the angular extent of the reflection with 4.5 nm spacing. However, overdose Hg makes the core proteins where the ordered fibrils of GAG are attached become coiled, which destroys the ordered arrangements of fibrillar GAG in PG, resulting in the disappearance of the reflections with 4.5 nm spacing. The disappearance of the 4.5 nm reflection can be used as a bioindicator of overdose Hg contamination to the human body. A supercoiled-coil model of hair nanoscale structure and a possible mechanism of mercury effect in human hair are proposed in this paper.

Strain-driven Kovacs-like memory effect in glasses.

Studying complex relaxation behaviors is of critical importance for understanding the nature of glasses. Here we report a Kovacs-like memory effect in glasses, manifested by non-monotonic stress relaxation during two-step high-to-low strains stimulations. During the stress relaxation process, if the strain jumps from a higher state to a lower state, the stress does not continue to decrease, but increases first and then decreases. The memory effect becomes stronger when the atomic motions become highly collective with a large activation energy, e.g. the strain in the first stage is larger, the temperature is higher, and the stimulation is longer. The physical origin of the stress memory effect is studied based on the relaxation kinetics and the in-situ synchrotron X-ray experiments. The stress memory effect is probably a universal phenomenon in different types of glasses.