RESUMO
Multitip probes are very useful diagnostics for analyzing and controlling the physical phenomena occurring in low temperature discharge plasmas. However, DC biased probes often fail to perform well in processing plasmas. The objective of the work was to deduce simple designs of DC biased multitip probes for parametric study of radio frequency plasmas. For this purpose, symmetric double probe, asymmetric double probe, and symmetric triple probe diagnostic systems and their driving circuits were designed and tested in an inductively coupled plasma (ICP) generated by a 13.56 MHz radio frequency (RF) source. Using I-V characteristics of these probes, electron temperature, electron number density, and ion saturation current was measured as a function of input power and filling gas pressure. An increasing trend was noticed in electron temperature and electron number density for increasing input RF power whilst a decreasing trend was evident in these parameters when measured against filling gas pressure. In addition, the electron energy probability function (EEPF) was also studied by using an asymmetric double probe. These studies confirmed the non-Maxwellian nature of the EEPF and the presence of two groups of the energetic electrons at low filling gas pressures.
Assuntos
Desenho Assistido por Computador , Condutometria/instrumentação , Eletrodos , Gases em Plasma/análise , Gases em Plasma/química , Transdutores , Desenho de Equipamento , Análise de Falha de Equipamento , Ondas de RádioRESUMO
The objective of the research was to understand and improve the unusual physical and atomization properties of the complexes/adhesives derived from the tapioca starch by addition of borate and urea. The characterization of physical properties of the synthesized adhesives was carried out by determining the effect of temperature, shear rate, and mass concentration of thickener/stabilizer on the complex viscosity, density, and surface tension. In later stage, phenomenological analyses of spray jet breakup of heated complexes were performed in still air. Using a high speed digital camera, the jet breakup dynamics were visualized as a function of the system input parameters. The further analysis of the grabbed images confirmed the strong influence of the input processing parameters on full cone spray patternation. It was also predicted that the heated starch adhesive solutions generate a dispersed spray pattern by utilizing the partial evaporation of the spraying medium. Below 40°C of heating temperature, the radial spray cone width and angle did not vary significantly with increasing Reynolds and Weber numbers at early injection phases leading to increased macroscopic spray propagation. The discharge coefficient, mean flow rate, and mean flow velocity were significantly influenced by the load pressure but less affected by the temperature.
Assuntos
Aerossóis/química , Manihot/química , Amido/química , Adesivos/química , Boratos/química , Técnicas de Química Sintética/instrumentação , Temperatura Alta , Ureia/químicaRESUMO
Melamine formaldehyde (MF) resins have been synthesized at different reaction temperature and pH values. Different molar ratios of melamine and formaldehyde were used to synthesize the corresponding resins. The prepared resin samples were characterized by using molecular weight determination viscometry and thermogravimetric analysis (TGA). The maximum percentage of solid content (69.7%) was obtained at pH 8.5 and 75°C temperature. The molecular weight of MF resin was increased with an increase of melamine monomer concentration. The highest residual weight 14.125 wt.% was obtained with sample 10.
Assuntos
Resinas Sintéticas/síntese química , Temperatura , Triazinas/síntese química , Triazinas/metabolismo , Resinas Sintéticas/metabolismoRESUMO
The hot water sprays are an important part of many industrial processes, where the detailed knowledge of physical phenomena involved in jet transportation, interaction, secondary breakup, evaporation, and coalescence of droplets is important to reach more efficient processes. The objective of the work was to study the water spray jet breakup dynamics, vortex cloud formation, and droplet size distribution under varying temperature and load pressure. Using a high speed camera, the spray patterns generated by axisymmetric full cone nozzles were visualized as a function water temperature and load pressure. The image analysis confirmed that the spray cone angle and width do not vary significantly with increasing Reynolds and Weber numbers at early injection phases leading to increased macroscopic spray propagation. The formation and decay of semitorus like vortex clouds were also noticed in spray structures generated at near water boiling point temperature. For the nozzle with smallest orifice diameter (1.19 mm), these vortex clouds were very clear at 90°C heating temperature and 1 bar water load pressure. In addition, the sauter mean diameter (SMD) of the spray droplets was also measured by using Phase Doppler Anemometry (PDA) at different locations downstream of the nozzle exit. It was noticed that SMD varies slightly w.r.t. position when measured at room temperature whereas at higher temperature values, it became almost constant at distance of 55 mm downstream of the nozzle exit.
Assuntos
Hidrodinâmica , Tecnologia/instrumentação , Desenho de Equipamento , Temperatura Alta , Tamanho da Partícula , Pressão , ÁguaRESUMO
Although photocatalytic technology has emerged as an effective means of alleviating the projected future fuel crisis by converting sunlight directly into chemical energy, no visible-light-driven, low-cost, and highly stable photocatalyst has been developed to date. Due to considerably higher interfacial contact with numerous reactive sites, effective charge transmission and separation ability, and strong redox potentials, the focus has now shifted to 2D/2D heterojunction systems, which have exhibited effective photocatalytic performance. The fundamentals of 2D/2D photocatalysis for different applications and the classification of 2D/2D materials are first explained in this paper, followed by strategies to improve the photocatalytic performance of various 2D/2D heterojunction systems. Following that, current breakthroughs in 2D/2D metal-based and metal-free heterojunction photocatalysts, as well as their applications for H2 evolution via water splitting, CO2 reduction, and N2 fixation, are discussed. Finally, a brief overview of current constraints and predicted results for 2D/2D heterojunction systems is also presented. This paper lays out a strategy for developing efficient 2D/2D heterojunction photocatalysts and sophisticated technology for solar fuel applications in order to address the energy issue.
RESUMO
An argon plasma jet was sustained in open air and characterized for its chemical composition. The optically characterized plasma jet was used to treat industrial wastewater containing mixed textile dyes and heavy metals. Since plasma jet produces UV-radiations, the photocatalytic TiO2 was used to enhance plasma treatment efficiency especially for degradation of dyes. Mixed anatase and rutile phases of TiO2 (5.2-8.5 nm) were produced through surfactant assisted sol-gel approach. The emission spectrum confirmed the presence of excited argon, OH, excited nitrogen, excited oxygen, ozone and nitric oxide in the plasma jet. The spectral lines of excited Ar, NO, O3, OH-, N2, [Formula: see text], O, [Formula: see text] and O+ species were observed at wavelength of 695-740 nm, 254.3 nm, 307.9 nm, 302-310 nm, 330-380 nm, 390-415 nm, 715.6 nm, 500-600 nm and 400-500 nm. These reactive species decompose the organic pollutants and separate the heavy metals from the water samples. The conductivity of plasma exposed water samples increased while pH and hardness decreased. The atomic absorption spectrophotometry analysis confirmed the presence of heavy metals in the samples, which were effectively removed through plasma treatment. Finally, the effect of plasma treatment on Staphylococcus aureus strains was more pronounced than Escherichia coli strains.
RESUMO
Fluidized bed technology is being used in several industrial processes. The well-controlled fluidization of a bed material is a prerequisite for successful implementation of this technology. Several variants of distributors are being tested for fluidized beds; however, scant information is available on their working regimes. In this study, an annular distributor was constructed by fixing blades between two concentric rings and covering the assembly with a wire mesh. This new distributor design was tested for fluidization of batches of a spherical bed material at different blade angles and superficial air velocities (SAVs). High-speed imaging and MATLAB supported velocimetry techniques were used to generate velocity vector fields of fluidized beds. These fields were analyzed further for bed velocity measurements at different bed zones. A response surface regression model was applied on the data to predict the response of the bed parameters. Statistically, the bed velocity was predicted to be about 0.497 m/s with the confidence interval in the range of 0.4948-0.4999. The experimental bed velocity remained between 0.531 m/s and 0.538 m/s under an optimized blade angle of 60°, SAV of 2.3 m/s, and bed weight of 500 g.
RESUMO
This study examines the analytical and numerical solution of electromagnetic surface waves supported by a resistive metasurface-covered grounded metamaterial structure. To simulate the metamaterial, the Kramers-Kronig relation based on the causality principle is used, while the modeling of the resistive metasurface has been done by implementing the impedance boundary conditions. The analytical expressions for the field phasors of surface waves are developed for the transverse magnetic (TM) polarized mode and transverse electric (TE) polarized mode. The characteristic equations are computed for both modes, and the unknown propagation constant is evaluated numerically in the kernel. After computation, the dispersion curves, electric field profiles, effective mode index ([Formula: see text]), and phase speeds ([Formula: see text]) are presented for both the TM and TE polarized modes. To study the tunability of surface waves, the influence of the thickness of the metamaterial slab ([Formula: see text]), effective permittivity of the metamaterial ([Formula: see text]), thickness of the resistive metasurface ([Formula: see text]), and effective permittivity of the metasurface ([Formula: see text]) on all the numerical results has been studied. However, the geometrical parameters are found to be more sensitive to the effective mode index ([Formula: see text]) and phase speed ([Formula: see text]) of the surface waves. The results are consistent with the published results, which reflects the accuracy of the work. It is concluded that the appropriate choice of parameters can be used to achieve surface waves with the desired characteristics in the GHz range. The present work may have potential applications in surface waveguide design, surface wave speed controllers, surface communication devices, and light trapping configurations.
RESUMO
The world does not have too much time to ensure that the fast-growing population has enough land, food, water and energy. The rising food demand has brought a positive surge in fertilizers' demand and agriculture-based economy. The world is using 170 million tons of fertilizer every year for food, fuel, fiber, and feed. The nitrogenous fertilizers are being used to meet 48% of the total food demand of the world. High fertilizer inputs augment the reactive nitrogen levels in soil, air, and water. The unassimilated reactive nitrogen changes into a pollutant and harms the natural resources. The use of controlled-release fertilizers for slowing down the nutrients' leaching has recently been practiced by farmers. However, to date, monitoring of the complete discharge time and discharge rate of controlled released fertilizers is not completely understood by the researchers. In this work, corn starch was thermally processed into a week gel-like coating material by reacting with urea and borate. The granular urea was coated with native and processed starch in a fluidized bed reactor having bottom-up fluid delivery system. The processed starch exhibited better thermal and mechanical stability as compared to the native starch. Unlike the pure starch, the storage modulus of the processed starch dominated the loss modulus. The release time of urea, coated with processed starch, remained remarkably larger than the uncoated urea.
RESUMO
This study investigated the dry and aqueous erosion of mild steel using electrochemical and dry sand impact techniques. In dry sand impact experiments, mild steel was eroded with 45 µm and 150 µm sand particles. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX) and micro-hardness techniques were used to elaborate the surface morphology of the eroded samples. The results revealed significant change in morphology of the eroded samples. In-depth analysis showed that although the metal erosion due to larger particles was significantly higher, the fines also notably damaged the metal surface. The surface damages were appreciably reduced with decrease in impact angle of the accelerated particles. The maximum damages were observed at an impact angle of 90°. The hardness of the samples treated with 45 µm and 150 µm sand remained in the range of 88.34 to 102.31 VHN and 87.7 to 97.55 VHN, respectively. In electrochemical experiments, a triple electrode probe was added into the metal treatment process. The linear polarization resistance (LPR) measurements were performed in slurries having 5% (by weight) of sand particles. LPR of the samples treated with 45 µm and 150 µm sand slurries was calculated about 949 Ω.cm(2) and 809 Ω.cm(2), respectively.