Long term performance of porous platinum coated neural electrodes.

Over the last several years, there has been a growing interest in neural implants for the study and diagnostics of neurological disorders as well as for the symptomatic treatment of central nervous system related diseases. One of the major challenges is the trade-off between small electrode sizes for high selectivity between single neurons and large electrode-tissue interface areas for excellent stimulation and recording properties. This paper presents an approach of increasing the real surface area of the electrodes by creating a surface microstructure. Two major novelties let this work stand out from existing approaches which mainly make use of porous coatings such as platinum black or iridium oxide, or Poly(3,4-ethylenedioxythiophene) (PEDOT). Roughening is carried out by a dry etching process on the silicon electrode core before being coated by a sputtered platinum layer, eliminating complicated deposition processes as for the materials described above. The technology is compatible with any commonly used coating material. In addition, the surface roughening is compatible with high aspect ratio penetrating electrode arrays such as the well-established Utah electrode array, whose unique geometry presents a challenge in the surface modification of active electrode sites. The dry etching process is well characterized and yields a high controllability of pore size and depth. This paper confirms the superior electrochemical properties including impedance, charge injection capacity, and charge storage capacity of surface engineered electrode arrays compared to conventional arrays over a period of 12 weeks. Furthermore, mechanical stability of the modified electrodes was tested by implantation in the brain of a recently deceased rat. In conclusion, the larger interface surface of the electrodes does not only decrease the impedance which should lead to enhanced Signal to noise ratio (SNR) for recording purposes, but also yields higher charge injection capacities, which improve the stimulation characteristics of the implants.

Reusable High Aspect Ratio 3-D Nickel Shadow Mask.

Shadow Mask technology has been used over the years for resistless patterning and to pattern on unconventional surfaces, fragile substrate and biomaterial. In this work, we are presenting a novel method to fabricate high aspect ratio (15:1) three-dimensional (3D) Nickel (Ni) shadow mask with vertical pattern length and width of 1.2 mm and 40 µm respectively. The Ni shadow mask is 1.5 mm tall and 100 µm wide at the base. The aspect ratio of the shadow mask is 15. Ni shadow mask is mechanically robust and hence easy to handle. It is also reusable and used to pattern the sidewalls of unconventional and complex 3D geometries such as microneedles or neural electrodes (such as the Utah array). The standard Utah array has 100 active sites at the tip of the shaft. Using the proposed high aspect ratio Ni shadow mask, the Utah array can accommodate 300 active sites, 200 of which will be along and around the shaft. The robust Ni shadow mask is fabricated using laser patterning and electroplating techniques. The use of Ni 3D shadow mask will lower the fabrication cost, complexity and time for patterning out-of-plane structures.

Different methods to alter surface morphology of high aspect ratio structures.

In various applications such as neural prostheses or solar cells, there is a need to alter the surface morphology of high aspect ratio structures so that the real surface area is greater than geometrical area. The change in surface morphology enhances the devices functionality. One of the applications of altering the surface morphology is of neural implants such as the Utah electrode array (UEA) that communicate with single neurons by charge injection induced stimulation or by recording electrical neural signals. For high selectivity between single cells of the nervous system, the electrode surface area is required to be as small as possible, while the impedance is required to be as low as possible for good signal to noise ratios (SNR) during neural recording. For stimulation, high charge injection and charge transfer capacities of the electrodes are required, which increase with the electrode surface. Traditionally, researchers have worked with either increasing the roughness of the existing metallization (Platinum grey, black) or other materials such as Iridium Oxide and PEDOT. All of these previously investigated methods lead to more complicated metal deposition processes that are difficult to control and often have a critical impact on the mechanical properties of the metal films. Therefore, a modification of the surface underneath the electrode's coating will increase its surface area while maintaining the standard and well controlled metal deposition process. In this work, the surfaces of the Silicon micro-needles were engineered by creating a defined microstructure on the electrodes surface using several methods such as Laser ablation, focused ion beam, sputter etching, reactive ion etching (RIE) and deep reactive ion etching (DRIE). The surface modification processes were optimized for the high aspect ratio Silicon structures of the UEA. The increase in real surface area while maintaining the geometrical surface area was verified using scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS). The best results were obtained by DRIE induced surface morphology. Decreases in impedance values of electrodes up to 76 % indicate the successful surface engineering of the high aspect ratio Silicon structures.

Correlation of partial env gene sequences with disease progression parameters in HIV-positive pregnant women from India.

Ever since the beginning of the epidemic of HIV, one of the poignant aspects of HIV infection is transmission of the virus from mother to child. It is not known whether pregnancy accelerates the progression of HIV infection from a clinically asymptomatic stage to a progressive clinical phase. Present study was carried out to understand disease progression in pregnant women from India. We studied co-receptor utilization (the major determinant of HIV disease progression), N-glycosylation sites, and sequence variability. Blood samples were collected from 25 HIV sero-positive patients, eleven from the antenatal risk group (experimental group), nine from heterosexual male, and five from heterosexual female risk group (control group). Partial env gene was amplified by PCR and sequenced. BLAST search and phylogenetic analysis were used to determine the subtype. The deduced amino acid sequence of the V3 region was used to predict co-receptor, determine sequence variability and N-glycosylation site. The experimental group comprising the antenatal risk group did not exhibit any difference in terms of co-receptor, N-glycosylation, and sequence variability when compared with the control, non-pregnant group. Pregnancy does not seem to accelerate the clinical course of HIV infection. The female body during the gestation phase possibly acquires certain strategies to impede or at least alleviate the disease progression during the crucial immune-compromised pregnancy phase, which would otherwise adversely affect the mother as well as the fetus during the infection.

Genetic analysis of precore/core and partial pol genes in an unprecedented outbreak of fulminant hepatitis B in India.

We investigated an unprecedented outbreak of fulminant hepatitis B virus (HBV) that occurred in Modasa, Gujarat (India) in 2009. Genomic analysis of all fulminant hepatic failure cases confirmed exclusive predominance of subgenotype D1. A1762T, G1764A basal core promoter (BCP) mutations, insertion of isoleucine after nt 1843, stop codon mutation G1896A, G1862T transversion plus seven other mutations in the core gene caused inhibition of HBeAg expression implicating them as circulating precore/BCP mutant virus. Two rare mutations at amino acids 89 (Ile→Ala) and 119 (Leu→Ser) in addition to other mutations in the polymerase (pol) gene may have caused some alteration in either of four pol gene domains to affect encapsidation of pregenomic RNA to enhance pathogenicity. Sequence similarity among patients' sequences suggested an involvement of a single hepatitis B mutant strain/source to corroborate the finding of gross and continued usage of HBV mutant-contaminated syringes/needles by a physician which resulted in this unprecedented outbreak of fulminant hepatitis B. The fulminant exacerbation of the disease might be attributed to mutations in the BCP/precore/core and pol genes that may have occurred due to selection pressure during rapid spread/mutation of the virus.

Significance of circulating toxin and antitoxin in unimmunized tetanus cases of neonates and infants.

The level of circulating tetanus toxin, antitoxin and their individual influence on the outcome of tetanus cases were determined in unimmunized 125 neonatal and 39 infant cases of tetanus. PHA (passive haemagglutination) test showed 40% positive cases for toxin while its absence in the remaining cases indicated of either toxin fixation to the central nervous system (CNS) or it got neutralized by antitoxin. TN (toxin neutralization) and PHA test carried out in 46 sera samples revealed a strong positive correlation (r = 0.9) showing that 35/46 (76%) and 38/46 (82.6%) samples were positive for antitoxin, respectively. 25.4% of the neonate and infant cases and 34% of the control group had a protective serum tetanus antitoxin level. 42.5% of the paired sera from unimmunized mothers and their neonates showing nonprotective antitoxin levels suggested that a high level of antitoxin is needed for transplacental transfer, although transfer may not play a decisive role in the resistance against the disease. The presence of toxin or antitoxin in the clinical cases did not affect the outcome of the disease, although in neonates, presence of toxin was found to be a bad prognostic sign. This study explicitly advocates for the need to improve the vaccination coverage strategy.

Pain relief after Frey's procedure for chronic pancreatitis.

BACKGROUND: Few studies have addressed long-term pain relief after Frey's procedure (local head resection with lateral pancreaticojejunostomy, LR-LPJ) for chronic pancreatitis. This retrospective study evaluated pain control using a validated score and risk factors associated with failure to achieve complete pain relief following LR-LPJ. METHODS: Sixty of 134 patients with chronic pancreatitis underwent LR-LPJ and were evaluated prospectively using the Izbicki pain score before surgery, and 1, 2, 5 and 7 years later. Analysis was on an intention-to-treat basis and predictors of complete pain relief were identified by multivariable analysis. RESULTS: After a median follow-up of 6.4 years, the median pain score was reduced from 46.4 to 10.0 (P < 0.001) with partial or complete pain relief in 75 per cent of patients, and a significant reduction in median number of episodes requiring hospitalization (from 4 to 0; P < 0.001). Preoperative use of opiate medication (odds ratio (OR) 30.14; P = 0.015), continuous pattern of pain (OR 22.65; P = 0.025) and occurrence of postoperative complications (OR 10.52; P = 0.030) were significant predictors of failure to achieve complete pain relief after surgery. CONCLUSION: Frey's procedure leads to significant and sustained long-term pain relief in patients with chronic pancreatitis. Patients should be referred for surgery before opiates are needed to relieve pain.

A Wafer-Scale Etching Technique for High Aspect Ratio Implantable MEMS Structures.

Microsystem technology is well suited to batch fabricate microelectrode arrays, such as the Utah electrode array (UEA), intended for recording and stimulating neural tissue. Fabrication of the UEA is primarily based on the use of dicing and wet etching to achieve high aspect ratio (15:1) penetrating electrodes. An important step in the array fabrication is the etching of electrodes to produce needle-shape electrodes with sharp tips. Traditional etching processes are performed on a single array, and the etching conditions are not optimized. As a result, the process leads to variable geometries of electrodes within an array. Furthermore, the process is not only time consuming but also labor-intensive. This report presents a wafer-scale etching method for the UEA. The method offers several advantages, such as substantial reduction in the processing time, higher throughput and lower cost. More importantly, the method increases the geometrical uniformity from electrode to electrode within an array (1.5 ± 0.5 % non-uniformity), and from array to array within a wafer (2 ± 0.3 % non-uniformity). Also, the etching rate of silicon columns, produced by dicing, are studied as a function of temperature, etching time and stirring rate in a nitric acid rich HF-HNO(3) solution. These parameters were found to be related to the etching rates over the ranges studied and more-importantly affect the uniformity of the etched silicon columns. An optimum etching condition was established to achieve uniform shape electrode arrays on wafer-scale.

Disseminated Histoplasmosis detected on peripheral blood smear examination in immunocompetent patients from non endemic region - Report of two cases from a tertiary care hospital.

Histoplasmosis is an opportunistic systemic infection caused by inhaling spores of a thermal dimorphic fungus Histoplasma capsulatum. Disseminated histoplasmosis is the most common form associated with acquired immune deficiency syndrome (AIDS). However, only a few cases of disseminated histoplasmosis are reported in immuno-competent hosts. Most infections in the immunocompetent hosts are asymptomatic or result in mild pulmonary disease. However the presence of Disseminated Histoplasmosis in immunocompetent host probably results due to prolonged exposure and delayed presentation We report two cases of progressive disseminated histoplasmosis in two immunocompetent patients from non-endemic region in Western Rajasthan, India. Also in both the cases, the first diagnosis was suggested by a peripheral blood smear, which is not a classical biological diagnostic method for fungal infection. Careful examination of Peripheral blood smear along with correct clinical history can aid in early diagnosis of disseminated histoplasmosis even in immunocompetent patients.

Integrated wireless neural interface based on the Utah electrode array.

This report presents results from research towards a fully integrated, wireless neural interface consisting of a 100-channel microelectrode array, a custom-designed signal processing and telemetry IC, an inductive power receiving coil, and SMD capacitors. An integration concept for such a device was developed, and the materials and methods used to implement this concept were investigated. We developed a multi-level hybrid assembly process that used the Utah Electrode Array (UEA) as a circuit board. The signal processing IC was flip-chip bonded to the UEA using Au/Sn reflow soldering, and included amplifiers for up to 100 channels, signal processing units, an RF transmitter, and a power receiving and clock recovery module. An under bump metallization (UBM) using potentially biocompatible materials was developed and optimized, which consisted of a sputter deposited Ti/Pt/Au thin film stack with layer thicknesses of 50/150/150 nm, respectively. After flip-chip bonding, an underfiller was applied between the IC and the UEA to improve mechanical stability and prevent fluid ingress in in vivo conditions. A planar power receiving coil fabricated by patterning electroplated gold films on polyimide substrates was connected to the IC by using a custom metallized ceramic spacer and SnCu reflow soldering. The SnCu soldering was also used to assemble SMD capacitors on the UEA. The mechanical properties and stability of the optimized interconnections between the UEA and the IC and SMD components were measured. Measurements included the tape tests to evaluate UBM adhesion, shear testing between the Au/Sn solder bumps and the substrate, and accelerated lifetime testing of the long-term stability for the underfiller material coated with a a-SiC(x):H by PECVD, which was intended as a device encapsulation layer. The materials and processes used to generate the integrated neural interface device were found to yield a robust and reliable integrated package.

Sex Conversion in a Male Vitis vinifera L. by a Kinin.

A synthetic (reputed) kinin, SD 8339, at 1000 parts per million in alcohol solution, applied to flower clusters of a male grapevine about 3 weeks before anthesis, completely converted the flower sex from male to hermaphrodite. Indolebutyric acid, 2,3,5-triiodobenzoic acid, 2-chloroethyltrimethylammonium chloride beta-naphthoxyacetic acid, beta-indoleacetic acid, alpha-naphthaleneacetic acid, and gibberellin A(3) failed to modify the sex.

Fine-tuning the photosynthetic light harvesting apparatus for improved photosynthetic efficiency and biomass yield.

Photosynthetic electron transport rates in higher plants and green algae are light-saturated at approximately one quarter of full sunlight intensity. This is due to the large optical cross section of plant light harvesting antenna complexes which capture photons at a rate nearly 10-fold faster than the rate-limiting step in electron transport. As a result, 75% of the light captured at full sunlight intensities is reradiated as heat or fluorescence. Previously, it has been demonstrated that reductions in the optical cross-section of the light-harvesting antenna can lead to substantial improvements in algal photosynthetic rates and biomass yield. By surveying a range of light harvesting antenna sizes achieved by reduction in chlorophyll b levels, we have determined that there is an optimal light-harvesting antenna size that results in the greatest whole plant photosynthetic performance. We also uncover a sharp transition point where further reductions or increases in antenna size reduce photosynthetic efficiency, tolerance to light stress, and impact thylakoid membrane architecture. Plants with optimized antenna sizes are shown to perform well not only in controlled greenhouse conditions, but also in the field achieving a 40% increase in biomass yield.

Cutaneous leishmaniasis in Bikaner, India: Clinicoepidemiological profile; parasite identification using conventional, molecular methods and CL Detect™ rapid test, a new Food and Drug Administration-approved test.

BACKGROUND AND OBJECTIVE: Cutaneous Leishmaniasis (CL) is a dermal manifestation caused by various species of Leishmania. This is the most common Leishmanial syndrome seen worldwide and is emerging as and threatens to become an uncontrollable disease. The present study was planned to understand the current epidemiology of CL in the conventionally endemic area of Bikaner, Rajasthan. Species characterization was also done. MATERIAL AND METHODS: The diagnostic modalities used in the study were microscopy, histopathologic examination, antigen testing and confirmation and species characterization by PCR. Field evaluation of the new antigen detection kit approved by FDA in 2016 CL Detect™ IC-RDT was done and its results compared with other available diagnostic tests. RESULTS: A total of 14 cases with 25 skin lesions presented to the Skin OPD during the six month study period (January to June 2018). Out of these, 5 were males and 9 were females, average age being 32 yrs. Students and housewives of poor socio economic group were the most frequently affected groups. Lesions were found on the exposed areas of the body, mainly on the upper limbs and facial region. Majority of them were ulcerated plaques. Out of 14 cases under study, antigen test confirmed 7 positives; thereby yielding a positive rate of 50% against 71.4% for microscopy, 72.7% for PCR and a mere 38.5% for histopathology. Species characterization revealed Leishmania tropica as the causative organism. INTERPRETATION AND CONCLUSION: The study indicates that the number of cases have declined substantially over the past decade in Bikaner. Despite being the oldest technique used, microscopy still is a good option for diagnosis. Combined with PCR, diagnostic accuracy and hence utility is increased multifold. In its current form, IC-RDT may not be very useful.

A Novel Method of Fabricating Convoluted Shaped Electrode Arrays for Neural and Retinal Prostheses.

A novel fabrication technique has been developed for creating high density (6.25 electrodes/mm(2)), out of plane, high aspect ratio silicon-based convoluted microelectrode arrays for neural and retinal prostheses. The convoluted shape of the surface defined by the tips of the electrodes could compliment the curved surfaces of peripheral nerves and the cortex, and in the case of retina, its spherical geometry. The geometry of these electrode arrays has the potential to facilitate implantation in the nerve fascicles and to physically stabilize it against displacement after insertion. This report presents a unique combination of variable depth dicing and wet isotropic etching for the fabrication of a variety of convoluted neural array geometries. Also, a method of deinsulating the electrode tips using photoresist as a mask and the limitations of this technique on uniformity are discussed.

First Report of Plum pox virus on Plum in New York State.

Plum pox, also known as Sharka, is one of the more significant viral diseases of stone fruit trees such as plum, peach, and apricot. It was first reported in Europe in the early 1900s and more recently in Chile in 1992, the United States (Pennsylvania) in 1999, Canada (Ontario and Nova Scotia) in 2000, China in 2001, and Argentina in 2004. Plum pox virus (PPV) was recently detected in two plum (Prunus domestica) trees in an orchard in Niagara County, NY, located within 5 miles from a Canadian plum pox eradication zone. Typical symptoms of chlorotic rings and spots were observed on some of the leaves from these trees. No symptoms were reported prior to the survey collection in July 2006. Survey samples were screened for the presence of PPV by ELISA using the Agdia PPV (Agdia, Elkhart, IN) specific kit that recognizes all strains but C of PPV. Approximately 5% of the survey samples were additionally analyzed by a validated immunocapture reverse transcription (IC-RT)-PCR TaqMan assay in a Cepheid SmartCycler (Cepheid, Sunnyvale, CA). Both replicates of the two New York plum trees produced a positive ELISA reaction in two consecutive tests. The ELISA-positive samples also produced positive results when subjected to the real-time IC-RT-PCR test. The PPV-positive trees were sampled again and an additional 53 samples were collected from trees in the surrounding area. Suspect trees again tested positive, while all the trees in the surrounding area tested negative. The methods used for confirmation included two ELISA tests (Durviz [Valencia, Spain] DAS indirect monoclonal ELISA and Agdia DAS polyclonal ELISA). Confirmatory real-time IC-RT-PCR was performed using universal 3' nontranslated region (NTR) primers (2,3) in a SYBR Green assay format and a coat protein (CP) primers/probe TaqMan assay (3,4). Further, the New York PPV isolate was identified as PPV D group using a subgroup specific conventional IC-RT-PCR (1). A 1.4-kb sequence fragment from the 3' end of the New York PPV was sequenced (GenBank Accession No. DG 883816). Comparison of the sequence with the database confirmed this isolate as subgroup D and exhibited a high degree of identity with other PPV D accessions (PPV D Teycheney [Accession No. X16415]; Penn4 [Accession No. DQ465243] Cnd 123-1 [Accession No. AY9553267]; and Cnd 3 [Accession No. AY953262]). To our knowledge, this is the first report of PPV in New York. References: (1) T. Candresse et al. Phytopathology. 88:198, 1998. (2) L. Levy et al. J. Virol. Methods. 49:295, 1994. (3) V. Mavrodieva and L. Levy. Acta Hortic. 657:141, 2004. (4) T. Wetzel et al. J.Virol. Methods 33:355, 1991.

Direct injection of calcitriol or its analog into hyperplastic parathyroid glands induces apoptosis of parathyroid cells.

Hyperplasia of the parathyroid gland (PTG) is associated not only with excessive secretion of parathyroid hormone (PTH) but also with changes in the parathyroid cell (PTC) characteristics (i.e. hyperproliferative activity, and low contents of vitamin D and calcium-sensing receptors). Control of PTG hyperplasia is most important in the management of secondary hyperparathyroidism, but the advanced stage of hyperplasia is considered irreversible. In the present study, dialysis patients with PTG hyperplasia underwent direct injection of calcitriol or maxacalcitol (OCT) into the PTG. Ultrasonography showed that this treatment had significantly reduced PTG volume and tissue analysis using the terminal deoxynucleotidyl transferase-mediated dUTP nick end-labeling (TUNEL) method and DNA electrophoresis indicated that cellular apoptosis had been induced. The mechanism of apoptosis was evaluated in detail in uremic rats fed a high-phosphate diet. OCT or its vehicle was directly injected into the rats' PTGs. In the PTGs treated by OCT, there was a significantly increased number of TUNEL-positive PTCs and DNA electrophoresis revealed the characteristic ladder pattern of DNA fragmentation, both findings indicative of apoptosis. There was also a significant upregulation of both vitamin D and Ca-sensing receptors in the PTCs and a clear shift of the Ca-PTH response curve to the left and downward. None of these findings was observed in the PTGs treated by vehicle. This novel treatment is successful in causing regression of PTG hyperplasia. Thus, it is expected to significantly reduce the PTH level and ameliorate the abnormal bone turnover and mineral metabolism.

Risk factors for perforation in microbial corneal ulcers in north India.

AIM: To identify predisposing factors leading to corneal perforation in patients with microbial keratitis. METHOD: Two groups of 60 patients each, with perforated corneal ulcers and healed/healing corneal ulcers, respectively, were recruited in a case-control study conducted in northern India. The cases and controls were matched by age and time of presentation. A standardised proforma was used to identify potential predisposing factors for demographic, social, medical, ocular, and treatment history. All participants underwent a detailed ocular examination. Corneal scrapings were performed where relevant. RESULTS: The characteristics associated with corneal perforation in microbial keratitis were outdoor occupation (p = 0.005), illiteracy (p = 0.02), excessive alcohol use (p = 0.03), history of "something falling into eye" (p = 0.003), trauma with vegetable matter (p = 0.008), vision less than counting fingers at referral (p<0.001), central location of ulcer (p<0.001), lack of corneal vascularisation (p<0.001), delay in starting initial treatment (p<0.001), failure to start fortified antibiotics (p<0.001), and monotherapy with fluoroquinolones (p = 0.002). The lack of corneal vascularisation (OR 6.4, 95% CI 4.2 to 13.5), delay in starting initial treatment (OR 35.6, 95% CI 6.9 to 68.2), and failure to start fortified antibiotics (OR 19.9, 95% CI 2.7 to 64.7) retained significance on a logistic regression model. CONCLUSIONS: This study characterises microbial keratitis cases at increased risk of corneal perforation and reinforces the need for standardised referral and treatment protocols for patients with corneal ulcer on their first contact at primary care level in the developing world.

Protein antigen b (Pab) based PCR test in diagnosis of pulmonary and extra-pulmonary tuberculosis.

BACKGROUND AND OBJECTIVES: Diagnosis of tuberculosis (TB) is largely based on microscopy and culture examination which are either less sensitive, or time consuming. In the present study a PCR (polymerase chain reaction) test based on DNA sequence coding for a 38-kilodalton protein antigen b (Pab) ,specific for Mycobacterium tuberculosis was compared with Ziehl-Neelsen (ZN) stained AFB (acid fast bacilli) smear examination, culture based on conventional Lowenstein-Jensen (LJ) medium and radiometric BACTEC 460 system for the diagnosis of TB using clinical samples obtained from pulmonary and extra-pulmonary cases of TB. METHODS: Clinical samples obtained from 168 patients of suspected TB (pulmonary and extrapulmonary) were subjected to ZN smear examination, LJ culture, radiometric BACTEC culture and a PCR test by amplifying 419 bp sequence coding for Pab, a glycoprotein of molecular weight 38 kDa. RESULTS: A significant difference was seen in the sensitivity of different tests, the figures being 74.2 per cent for PCR test, 53.4 per cent for BACTEC culture, 47.1 per cent for LJ medium based culture and 35.2 per cent for ZN smear examination (P<0.05). However, there was no significant difference between different tests as far as specificity was concerned. PCR test sensitivity in pulmonary and extra-pulmonary clinical samples were 74.3 and 71.5 per cent respectively, being significantly higher (P<0.05) when compared with sensitivity of other tests. The mean detection time for M. tuberculosis was 24.0 days by LJ media culture, 12.8 days by BACTEC culture and less than 1 day by smear examination and PCR test. INTERPRETATION AND CONCLUSION: PCR test is more sensitive than ZN smear examination, LJ medium culture and BACTEC culture for diagnosing TB in pulmonary and extra-pulmonary clinical samples.

Common nitrogen control of caesium uptake, caesium toxicity and ammonium (methylammonium) uptake in the cyanobacterium Nostoc muscorum.

Studies were carried out to examine the role of ammonium transport activity in the control of caesium uptake and toxicity in Nostoc muscorum. The results showed a definite specific role of the ammonium-repressible/derepressible ammonium transport system of the cyanobacterium in caesium uptake, accumulation and toxicity. Furthermore, the results showed that N. muscorum can acquire resistance against diazotrophically-associated caesium toxicity when supplied with ammonium as a nitrogen source. In addition, alternatively, a mutant strain was Cs-resistant in the absence of any effect on NH(+4)-transport, suggesting that Cs+ resistance may be determined at more than one cellular site.