Comparison of Mechanical and Structural Properties of Nickel-titanium Alloy with Titanium-molybdenum Alloy and Titanium-niobium Alloy as Potential Metals for Endodontic Files.

Introduction: The objective of this study was to compare the mechanical and structural properties of the nickel-titanium (Ni-Ti) alloy already used in endodontics with titanium-molybdenum (Ti-Mo) and titanium-niobium (Ti-Nb) alloys to determine if these can be suggested in the manufacture of endodontic files. Methods and Materials: Orthodontic wires made of the different alloys were used. The previously mentioned alloys were characterized by energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) and torsion tests. Cyclic fatigue tests were performed on a simulated canal with a curvature of 86° to 375 rpm. The fractured surfaces of the wires were observed by means of scanning electron microscopy (SEM). A Kruskal-Wallis test and U Mann Whitney test were used to determine significant differences in cyclic fatigue between groups. Results: In the mechanical tests, similar values of torsion were found for the three alloys. In XRD, the Ti-Nb showed less structural changes. In the cyclic fatigue test, Ti-Nb was found to be significantly more resistant with respect to Ni-Ti and Ti-Mo. Conclusion: Based on our in vitro study, Ti-Nb is suggested as a possible alloy for the manufacture of rotary files due to its impressive properties.

Pulp revascularization with and without platelet-rich plasma in two anterior teeth with horizontal radicular fractures: a case report.

Pulp revascularization is an alternative treatment in immature traumatized teeth with necrotic pulp. However, this procedure has not been reported in horizontal root fractures. This is a case report of a 9-year-old patient with multiple horizontal root fractures in 2 upper central incisors that were successfully treated with pulp revascularization. The patient presented for treatment 2 years after the initial trauma, and revascularization was attempted after the initial treatment with calcium hydroxide had failed. Prior to pulp revascularization, cone-beam computed tomography and autoradiograms demonstrated multiple horizontal fractures in the middle and apical thirds of the roots of the 2 affected teeth. Revascularization was performed in both teeth; platelet-rich plasma (PRP) was used in one tooth (#11) and the conventional method (blood clot) was used in the other tooth (#21). Clinical and radiographic follow-up over 4 years demonstrated pulp calcification in the PRP-treated tooth. Neither of the 2 teeth were lost, and the root canal calcification of tooth #11 was greater than that of tooth #21. This case suggests that PRP-based pulp revascularization may be an alternative for horizontal root fractures.

Assessment of the relationship between the maxillary sinus floor and the upper posterior root tips: Clinical considerations.

AIM: The purpose of the present study was to evaluate the relationship between the maxillary sinus floor and the upper posterior root tips in the Colombian population using cone-beam computed tomography. METHODS: A total of 1656 roots were analyzed (1104 molars and 552 premolars), classified as types I (outside the maxillary sinus) and II (inside the maxillary sinus). RESULTS: The results showed that the palatal root of the maxillary first molar was most frequently found inside the antrum. CONCLUSIONS: Understanding the relationship between the maxillary sinus floor and the upper posterior root tips is important to the clinician when performing conventional or surgical endodontic treatment and conventional surgery procedures in order to minimize or avoid the risk of damaging the maxillary sinus.

Surgical management with intentional replantation on a tooth with palato-radicular groove.

A palato-radicular groove (PRG) is a developmental anomaly primarily found in the maxillary lateral incisors. It is a potential communication path between the root canal and the periodontium that decreases the survival prognosis of the affected tooth, therefore compromising the stability of the dental structure in the oral cavity. The aim of this case report is to present an original technique where a PRG was treated by means of intracanal disinfection, PRG sealing with glass ionomer, replantation with intentional horizontal 180 degree rotation of the tooth, and an aesthetic veneer placed to provide adequate tooth morphology. The clinical and biological benefits of this novel technique are presented and discussed.

Utilidad de la conformación del túnel liso antes de usar limas rotatorias endodónticas de níquel-titanio / Usefulness of shaping the glide path before using rotary nickel-titanium endodontic files

Introducción: para prevenir la fractura de instrumentos endodonticos actualmente se siguen investigando materiales, técnicas y diseños los cuales buscan reducir su incidencia. La conformación de túnel liso (Glide Path) se ha propuesto con este fin, sin embargo su utilidad ha sido controvertida. Objetivo: comprobar teóricamente mediante la utilización de un análisis de elementos finitos, la utilidad de la conformación de túnel liso, antes de la utilización de limas rotatorias endodonticas de níquel-titanio. Métodos: se realizó una simulación numérica mediante un análisis de elementos finitos, para lo cual se construyeron modelos matemáticos de las limas rotatorias de níquel-titanio S1 y S2 de la serie Protaper®. Con el software Simulation multyphisics de Autodesk® se programaron las propiedades mecánicas de las limas y un límite de falla por fractura de 1270,588 MPa. Posteriormente se aplicó el torque recomendado por el fabricante y se fijo la punta del instrumento (sin conformación de túnel liso) aplicando allí restricciones en todos los grados de libertad.Para simular la realización de la conformación de túnel liso, se aplicaron restricciones en todos los grados de libertad a una determinada distancia de la punta del instrumento, simulando de esta forma que la punta del instrumento permanecía libre. Resultados: al fijar la punta de las limas, los esfuerzos máximos fueron 1545,77 MPa para la S1 y 1306,47 MPa para la S2, observando fractura de los instrumentos. Al fijar las limas a distancia de la punta no se observó fractura. Conclusiones: se demostró teóricamente que al impedir que se atrapen la punta de las limas, se previene su fractura y que dicho atrapamiento se evita con una conformación de túnel liso, por lo que se concluye que este procedimiento es útil para prevenir la fractura de los instrumentos rotatorios de níquel-titanio(AU)

Introduction: materials, techniques and designs continue to be studied with the purpose of reducing the incidence of fracture in endodontic instruments. Shaping of the glide path has been proposed for this end; however, its usefulness has been a matter of controversy. Objective: based on the finite element method, carry out a theoretical analysis of the usefulness of shaping the glide path before using rotary nickel-titanium endodontic files. Methods: numerical simulation was performed based on finite element analysis, to achieve which mathematical models were built of rotary nickel-titanium files S1 and S2 of the Protaper™ series. Autodesk™ Simulation Multiphysics software was used to program the mechanical properties of the files, as well as a fracture failure limit of 1270.588 MPa. The torque recommended by the manufacturer was then applied and the instrument tip fixed into place (without shaping the glide path) with restrictions on all degrees of freedom. In order to simulate glide path shaping, restrictions were applied to all degrees of freedom at a certain distance from the instrument tip, thus simulating that the instrument tip remained free. Results: on fixing the file tips, maximum efforts were 1545.77 Mpa for S1 and 1306.47 Mpa for S2. Instrument fracture was observed. When files were fixed at a distance from the tip, no fracture was observed. Conclusions: it was theoretically demonstrated that when file tips are prevented from being caught, fracture is prevented as well, and such catch is avoided by shaping the glide path. It is therefore concluded that the procedure is useful to prevent the fracture of rotary nickel-titanium instruments(AU)

Morfogénesis de los túbulos dentinales: un modelo matemático / Morphogenesis of dentinal tubules: a mathematical model

La diferenciación mesenquimal a odontoblasto es un proceso complejo que determina la formación de los túbulos dentinales. Este proceso involucra una cuidadosa y regulada secuencia de cambios en el comportamiento de las células mesenquimales, coordinados por la expresión de diferentes factores moleculares, entre ellos, principalmente, el Noggin y BMP2. En este artículo se simula la formación de los túbulos dentinales a partir de un modelo matemático de reacción difusión que es solucionado por el método de los elementos finitos...

Mesenchymal differentiation into odontoblasts is a complex process determining the formation of dentinal tubules. The process involves a carefully regulated sequence of changes in the behavior of mesenchymal cells, coordinated by the expression of various molecular factors, particularly Noggin and BMP2. In this paper the formation of dentinal tubules is simulated using a reaction-diffusion mathematical model solved by the finite element method...