Warmed contrast media temperature loss in traditional manifold systems during angiographic procedures.

BACKGROUND: Extrinsic warming of contrast media (CM) to 37 °C before angiographic procedures is performed to improve bolus kinetics and avoid potential adverse effects. Extrinsically warmed CM readily loses temperature after removal from the warming cabinet, but the extent of its cooling has not been previously investigated. PURPOSE: To assess temperature loss of extrinsically warmed CM in tubing of traditional angiographic manifolds during simulated angiography. MATERIAL AND METHODS: In total, 35 scheduled diagnostic angiographic procedures were observed in a hospital setting. Relevant time points of CM use during the procedures were recorded. The shortest, median, and longest procedures were then simulated in the experimental laboratory to measure CM temperatures at specific times at three locations along the tubing system. RESULTS: The angiographic procedures lasted 7.0-26.6 min (median = 11.7 min), with the total duration dependent primarily on the time from contrast being removed from the warming cabinet to the commencement of imaging. During the simulated procedures, consistent patterns of temperature loss were observed. By the last simulated angiographic run, injected CM temperature decreased by 7.4-16.4 °C, depending on procedure length. Most of the heat loss occurred in the tubing between the CM bottle and coronary control syringe. CONCLUSION: During angiographic procedures, prewarmed CM loses its temperature rapidly with the duration of exposure to ambient room temperature. If no additional measures are employed to maintain its temperature outside of the warming cabinet, extrinsic warming has limited impact on injected CM temperature.

A short-term evaluation of a prototype disposable Oscillating Positive Expiratory Pressure (OPEP) device in a cohort of children with cystic fibrosis.

BACKGROUND: Oscillating Positive Expiratory Pressure (OPEP) devices are important adjuncts to airway clearance therapy in patients with cystic fibrosis (CF). Current devices are typically reusable and require daily, or often more frequent, cleaning to prevent risk of infection by acting as reservoirs of potentially pathogenic organisms. In response, a daily disposable OPEP device, the UL-OPEP, was developed to mitigate the risk of contamination and eliminate the burdensome need for cleaning devices. METHODS: A convenience sample of 36 participants, all current OPEP device users, was recruited from a paediatric CF service. For one month, participants replaced their current OPEP device with a novel daily disposable device. Assessment included pre- and post-intervention lung function by spirometry, as well as Lung Clearance Index. Quality of life was assessed using the Cystic Fibrosis Questionnaire - Revised, while user experience was evaluated with a post-study survey. RESULTS: 31 participants completed the study: 18 males; median age 10 years, range 4-16 years. Lung function (mean difference ± SD, %FEV1 = 1.69 ± 11.93; %FVC = 0.58 ± 10.04; FEV1: FVC = 0.01 ± 0.09), LCI (mean difference ± SD, 0.08 ± 1.13), six-minute walk test, and CFQ-R were unchanged post-intervention. Participant-reported experiences of the device were predominantly positive. CONCLUSIONS: The disposable OPEP device maintained patients' lung function during short term use (≤ 1 month), and was the subject of positive feedback regarding functionality while reducing the risk of airway contamination associated with ineffective cleaning. REGISTRATION: The study was approved as a Clinical Investigation by the Irish Health Products Regulatory Authority (CRN-2209025-CI0085).

An initial evaluation of the safety of a disposable oscillating positive expiratory pressure device in patients with chronic obstructive pulmonary disease: a sort-term pilot study.

BACKGROUND: Handheld oscillating positive expiratory pressure (OPEP) devices have been a mainstay of treatment for patients with hypersecretory conditions such as cystic fibrosis (CF) and chronic obstructive pulmonary disease (COPD) since the 1970s. Current devices are reusable and require regular cleaning and disinfection to prevent harbouring potentially pathogenic organisms. Adherence to cleaning regimens for respiratory devices is often poor and in response to this, a prototype disposable OPEP device-the 'UL-OPEP' (University of Limerick-Oscillating Positive Expiratory Pressure device)-was developed to mitigate the risk of contamination by pathogens. The device was previously evaluated successfully in a group of paediatric CF patients. The aim of the current study was to initially evaluate the safety of the prototype in patients with COPD over a period of 1 month to ensure no adverse events, negative impacts on lung function, exercise tolerance, or quality of life. Data on user experience of the device were also collected during post-study follow-up. METHODS: A sample of 50 volunteer participants were recruited from pulmonary rehabilitation clinics within the local hospital network. The patients were clinically stable, productive, and not current or previous users of OPEP devices. Participants were invited to use a prototype disposable OPEP device daily for a period of 1 month. Pre- and post-study lung function was assessed with standard spirometry, and exercise tolerance with the 6-min-walk-test (6MWT). Quality of life was assessed using the St. George's Respiratory Questionnaire (SGRQ), and user experience of the prototype device evaluated using a post-study questionnaire. RESULTS: 24 Participants completed the study: 9 were female. Overall median age was 67.5 years, range 53-85 years. Lung function, 6-min walk test, and SGRQ scores showed no significant change post-study. User feedback was positive overall. CONCLUSIONS: The results indicate that the UL-OPEP is safe to use in patients with COPD. No adverse events were recorded during the study or in the follow-up period of 2 weeks. The device did not negatively impact patients' lung function, exercise tolerance, or quality of life during short term use (1 month), and usability feedback received was generally positive. Larger, longer duration studies will be required to evaluate efficacy. Registration The study was approved as a Clinical Investigation by the Irish Health Products Regulatory Authority (CRN-2209025-CI0085).

Relationship Between Interface Pressures and Pneumatic Cuff Inflation Pressure at Different Assessment Sites of the Lower Limb to Aid Soft Exoskeleton Design.

OBJECTIVE: The aim was to develop a means of predicting interface pressure from cuff inflation pressure during circumferential compression at the lower limb, in order to inform the design of soft exoskeletons. BACKGROUND: Excessive mechanical loading of tissues can cause discomfort and soft tissue injury. Most ergonomic studies on exoskeletons are of interface pressure, but soft exoskeletons apply circumferential pressures similar to tourniquet cuffs by way of cuff inflation pressure. This study details the relationship between interface and cuff inflation pressures for pneumatic tourniquet cuffs. METHOD: Pneumatic cuffs of different widths were inflated to target pressures on (A) a rigid cylinder, (B) the dominant thigh and calf, and (C) knee of healthy participants standing still. Interface pressures were measured under the cuffs using a pressure-sensing mat. Average interface pressures were then compared to cuff inflation pressures. The influence of cuff width, cuff inflation pressure, and participants' anthropometric data on pressure transmission was assessed. RESULTS: A strong linear relationship between cuff inflation pressures and interface pressures was observed. Interface pressures were generally higher than cuff inflation pressures. The efficiency of pressure transmission to the lower limb depended on assessment site, adipose tissue thickness, cuff size, cuff inflation pressure, and possibly limb circumference. Regression equations were developed to predict interface pressures at the thigh, calf, and knee. CONCLUSION: Interface pressures under pneumatic cuffs are influenced by the cuff size, cuff inflation pressure, and tissue compressibility. Predicted interface pressure from cuff inflation pressure and vice versa can be used to aid the design of soft exoskeletons.

Effects of industrial back-support exoskeletons on body loading and user experience: an updated systematic review.

This study is an updated systematic review of papers published in the last 5 years on industrial back-support exoskeletons. The research questions were aimed at addressing the recent findings regarding objective (e.g. body loading, user performance) and subjective evaluations (e.g. user satisfaction), potential side effects, and methodological aspects of usability testing. Thirteen studies of active and twenty of passive exoskeletons were identified. The exoskeletons were tested during lifting and bending tasks, predominantly in laboratory settings and among healthy young men. In general, decreases in participants' back-muscle activity, peak L5/S1 moments and spinal compression forces were reported. User endurance during lifting and static bending improved, but performance declined during tasks that required increased agility. The overall user satisfaction was moderate. Some side effects were observed, including increased abdominal/lower-limb muscle activity and changes in joint angles. A need was identified for further field studies, involving industrial workers, and reflecting actual work situations. Practitioner summary: Due to increased research activity in the field, a systematic review was performed of recent studies on industrial back-support exoskeletons, addressing objective and subjective evaluations, side effects, and methodological aspects of usability testing. The results indicate the efficiency of exoskeletons in back-load reduction and a need for further studies in real work situations. Abbrevaitions: BB: biceps brachii; BF: biceps femoris; CoM: centre of mass; DA: deltoideus anterior; EMG: electromyography; ES: erector spinae; ES-C: erector spinae-cervical; ESI: erector spinae iliocostalis; ESI-L: erector spinae iliocostalis-lumborum; ESL: erector spinae longissimus; ES-L: erector spinae-lumbar; ESL-L: erector spinae longissimus-lumborum; ESL-T: erector spinae longissimus-thoracis; ES-T: erector spinae-thoracic; GM: glutaeus maximus; LBP: low back pain; LD: latissimus dorsi; LPD: local perceived discomfort scale; LPP: local perceived pressure scale; MS: multifidus spinae; MSD: musculoskeletal disorder; M-SFS: modified spinal function sort; NMV: no mean value provided; OA: obliquus abdominis (internus and externus); OEA: obliquus externus abdominis; OIA : obliquus internus abdominis; RA: rectus abdominis; RF: rectus femoris; RoM: range of motion; SUS: system usability scale; T: trapezius (pars Ascendens and Descendens); TA: trapezius pars ascendens; TC: mid-cervical trapezius; TD: trapezius pars descendens; VAS: visual analog scale; VL: vastus lateralis; VM: vastus medialis.

Discomfort/Pain and Tissue Oxygenation at the Lower Limb During Circumferential Compression: Application to Soft Exoskeleton Design.

OBJECTIVE: To establish the relationship between circumferential compression on the lower limb during simulated ramp and staircase profile loading, and the resultant relationship with discomfort/pain and tissue oxygenation. BACKGROUND: Excessive mechanical loading by exoskeletons on the body can lead to pressure-related soft tissue injury. Potential tissue damage is associated with objective oxygen deprivation and accompanied by subjective perception of pain and discomfort. METHOD: Three widths of pneumatic cuffs were inflated at the dominant thigh and calf of healthy participants using two inflation patterns (ramp and staircase), using a computer-controlled pneumatic rig. Participants rated discomfort on an electronic visual analog scale and deep tissue oxygenation was monitored using near infrared spectroscopy. RESULTS: Circumferential compression with pneumatic cuffs triggered discomfort and pain at lower pressures at the thigh, with wider cuffs, and with a ramp inflation pattern. Staircase profile compression caused an increase in deep tissue oxygenation, whereas the ramp profile compression decreased it. CONCLUSION: Discomfort and pain during circumferential compression at the lower limb is related to the width of pneumatic cuffs, the inflation pattern, and the volume of soft tissue at the assessment site. The occurrence of pain is also possibly related to the decrease in deep tissue oxygenation during compression. APPLICATION: Our findings can be used to inform safe and comfortable design of soft exoskeletons to avoid discomfort and possible soft tissue injury.

Exoscore: A Design Tool to Evaluate Factors Associated With Technology Acceptance of Soft Lower Limb Exosuits by Older Adults.

OBJECTIVE: This pilot study proposed and performs initial testing with Exoscore, a design evaluation tool to assess factors related to acceptance of exoskeleton by older adults, during the technology development and testing phases. BACKGROUND: As longevity increases and our aging population continues to grow, assistive technologies such as exosuits and exoskeletons can provide enhanced quality of life and independence. Exoscore is a design and prototype stage evaluation method to assess factors related to perceptions of the technology, the aim being to optimize technology acceptance. METHOD: In this pilot study, we applied the three-phase Exoscore tool during testing with 11 older adults. The aims were to explore the feasibility and face validity of applying the design evaluation tool during user testing of a prototype soft lower limb exoskeleton. RESULTS: The Exoscore method is presented as part of an iterative design evaluation process. The method was applied during an exoskeleton research and development project. The data revealed the aspects of the concept design that rated favorably with the users and the aspects of the design that required more attention to improve their potential acceptance when deployed as finished products. CONCLUSION: Exoscore was effectively applied to three phases of evaluation during a testing session of a soft exoskeleton. Future exoskeleton development can benefit from the application of this design evaluation tool. APPLICATION: This study reveals how the introduction of Exoscore to exoskeleton development will be advantageous when assessing technology acceptance of exoskeletons by older adults.

Kinematic and kinetic functional requirements for industrial exoskeletons for lifting tasks and overhead lifting.

The aim of this study was to sample human kinematics and kinetics during simulated tasks to aid the design of industrial exoskeletons. Twelve participants performed two dynamic tasks; a simulated lifting task and an overhead lifting task. Based on the current data, to completely assist a worker with lifting loads up to 15 kg, hip actuators would need to supply up to 111 Nm of extensor torque at speeds up to 139°/s of extension velocity and 26°/s of flexion velocity. The actuators should allow the hip to extend to 11° and flex to 95°, and supply a power of 212 W. To completely assist workers lifting a 3 kg load overhead, actuators assisting shoulder flexion would need to supply up to 20 Nm of flexor torque at speeds up to 21°/s of extension velocity and 116°/s of flexion velocity. The actuators should also allow 67° of shoulder flexion and supply a power of 27 W. Practitioner summary: There is increasing interest in developing exoskeletons for industrial applications. This study details relevant kinetic and kinematic exposures for common production tasks, which can be used to inform functional requirements of industrial exoskeletons.AbbreviationsWMSD(s)work-related musculoskeletal disordersMMHmanual materials handlingDOFdegrees of freedomBLEEXBerkeley lower extremity exoskeletonLED(s)light emitting diodeRelrelativeHighlightsThis study sampled joint kinematic and kinetic activity to inform design of industrial exoskeletons.The study presents sample values to two types of common industrial tasks across the major joints as are often assisted.We also indicate considerations on which joints should be considered to be actively assisted.

The effect of simulated circumferential soft exoskeleton compression at the knee on discomfort and pain.

There is a lack of data and guidance on soft exoskeleton pressure contact with the body. The purpose of this research was to study the relationship between circumferential loading at the knee and discomfort/pain, to inform the design of soft exoskeletons/exosuits. The development of discomfort and pain was studied during standing and walking with circumferential compression using a pneumatic cuff. Our results show higher tolerance for intermittent than continuous compression during standing. Discomfort was triggered at pressures ranging from 13.7 kPa (continuous compression) to 30.4 kPa (intermittent compression), and pain at 52.9 kPa (continuous compression) to 60.6 kPa (intermittent compression). During walking, cyclic compression caused an increase in discomfort with time. Higher cuff inflation pressures caused an earlier onset and higher end intensities of discomfort than lower pressures. Cyclic cuff inflation of 10 kPa and 20 kPa was reasonably well tolerated. Practitioner summary Soft exoskeleton compression of the knee was simulated during static and dynamic compression cycles. The results can be used to understand how users tolerate pressure at the knee, and also to understand the levels at which discomfort and pain are experienced. Abbreviations: BMI: body mass index; DDT: discomfort detection threshold; EndVAS: end of experiment rating on visual analog discomfort scale; PDT: pain detection threshold; SD: standard deviation; SE: standard error; TSP: temporal summation of pain; VAS: visual analogue scale.

Age and sex related differences in shoulder abduction fatigue.

BACKGROUND: Injury prevalence data commonly indicate trends of higher rates of work-related musculoskeletal disorders in older workers over their younger counterparts, and for females more than males. The purpose of this study was to investigate age and sex-related differences in manifestations of shoulder muscle fatigue in a cohort of young and older working age males and females, in a single experiment design allowing for direct comparison of the fatigue effects between the target groups. METHODS: We report upper trapezius muscle fibre Conduction Velocity (CV) as an indicative measure of muscle fatigability, and isometric endurance time, at three levels of shoulder abduction lifting force set relative to participants' maximal strength. RESULTS: Upper trapezius conduction velocity was significantly different between the young and old groups (p = 0.002) as well as between males and females (p = 0.016). Shoulder abduction endurance time was affected by age (P = 0.024) but not sex (p = 0.170). CONCLUSIONS: The study identified age-related improvement in muscle fatigue resistance and increased resistance for females over males, contrary to injury prevalence trends. The muscle fatigue effects are most likely explained by muscle fibre type composition. Experimental fatigue treatments of the upper trapezius were tested at exposures relative to the participants' strength. Absolute strength is higher when young and is generally higher for males. The findings of this study point towards age and sex-related differences in strength rather than in muscle fatigue resistance as a primary cause for the differences in the injury trends.

Distress and worry as mediators in the relationship between psychosocial risks and upper body musculoskeletal complaints in highly automated manufacturing.

As a result of changes in manufacturing including an upward trend in automation and the advent of the fourth industrial revolution, the requirement for supervisory monitoring and consequently, cognitive demand has increased in automated manufacturing. The incidence of musculoskeletal disorders has also increased in the manufacturing sector. A model was developed based on survey data to test if distress and worry mediate the relationship between psychosocial factors (job control, cognitive demand, social isolation and skill discretion), stress states and symptoms of upper body musculoskeletal disorders in highly automated manufacturing companies (n = 235). These constructs facilitated the development of a statistically significant model (RMSEA 0.057, TLI 0.924, CFI 0.935). Cognitive demand was shown to be related to higher distress in employees, and distress to a higher incidence of self-reported shoulder and lower back symptoms. The mediation model incorporating stress states (distress, worry) as mediators is a novel approach in linking psychosocial risks to musculoskeletal disorders. Practitioners' Summary With little requirement for physical work in many modern automated manufacturing workplaces, there is often minimal management focus on Work-Related Musculoskeletal Disorders (WRMSDs) as important occupational health problems. Our model provides evidence that psychosocial factors are important risk factors in symptoms of WRMSD and should be managed.

Exoskeletons for industrial application and their potential effects on physical work load.

The aim of this review was to provide an overview of assistive exoskeletons that have specifically been developed for industrial purposes and to assess the potential effect of these exoskeletons on reduction of physical loading on the body. The search resulted in 40 papers describing 26 different industrial exoskeletons, of which 19 were active (actuated) and 7 were passive (non-actuated). For 13 exoskeletons, the effect on physical loading has been evaluated, mainly in terms of muscle activity. All passive exoskeletons retrieved were aimed to support the low back. Ten-forty per cent reductions in back muscle activity during dynamic lifting and static holding have been reported. Both lower body, trunk and upper body regions could benefit from active exoskeletons. Muscle activity reductions up to 80% have been reported as an effect of active exoskeletons. Exoskeletons have the potential to considerably reduce the underlying factors associated with work-related musculoskeletal injury. Practitioner Summary: Worldwide, a significant interest in industrial exoskeletons does exist, but a lack of specific safety standards and several technical issues hinder mainstay practical use of exoskeletons in industry. Specific issues include discomfort (for passive and active exoskeletons), weight of device, alignment with human anatomy and kinematics, and detection of human intention to enable smooth movement (for active exoskeletons).

Does Using a Chair Backrest or Reducing Seated Hip Flexion Influence Trunk Muscle Activity and Discomfort? A Systematic Review.

OBJECTIVE: This paper systematically reviews the effect of chair backrests and reducing seated hip flexion on low back discomfort (LBD) and trunk muscle activation. BACKGROUND: Prolonged sitting commonly exacerbates low back pain (LBP). Several modifications to seated posture and chair design have been recommended, including using chairs with backrests and chairs that reduce hip flexion. METHOD: Electronic databases were searched by two independent assessors. Part 1 of this review includes 26 studies comparing the effect of sitting with at least two different hip angles. In Part 2, seven studies that compared the effect of sitting with and without a backrest were eligible. Study quality was assessed using the PEDro scale. RESULTS: Significant confounding variables and a relatively small number of randomized controlled trials (RCTs) involving people with LBP complicates analysis of the results. There was moderate evidence that chair backrests reduce paraspinal muscle activation, and limited evidence that chair backrests reduce LBD. There was no evidence that chairs involving less hip flexion reduce LBP or LBD, or consistently alter trunk muscle activation. However, participants in several studies subjectively preferred the modified chairs involving less hip flexion. CONCLUSION: The limited evidence to support the use of chairs involving less seated hip flexion, or the effect of a backrest, is consistent with the limited evidence that other isolated chair design features can reduce LBP. APPLICATION: LBP management is likely to require consideration of several factors in addition to sitting position. Larger RCTs involving people with LBP are required.

Self-selected duty cycle times for grip force, wrist flexion postures and three grip types.

Performance and health issues are common in industry. On-the-job productivity gains related to good design, which could help justify ergonomics intervention, are often not considered. More quantitative data are needed to model the discomfort/productivity relationship for upper limb activity in simulated repetitive assembly type work. Eighteen participants completed an experiment, simulating a repetitive upper limb task with force, posture and grip type recorded as independent variables. Duty cycle time and discomfort were recorded as dependent variables. Participants performed 18 experiment combinations (block designed around force); each treatment lasted 35 min, including breaks. Analysis indicated a significant two-way interaction between posture and grip type. Results from this experiment were used to model the effect of these variables on operator discomfort and performance.

The effect of manual handling training on achieving training transfer, employee's behaviour change and subsequent reduction of work-related musculoskeletal disorders: a systematic review.

This systematic review investigated the effectiveness of manual handling training on achieving training transfer, leading to a positive change in employee's manual handling behaviour and a reduction of work-related musculoskeletal disorders (WRMSDs) following training. Six electronic databases were searched for randomised controlled trials, non-randomised controlled trials or cohort studies with a control and/or comparison group that investigated the effectiveness of manual handling training. Thirteen articles met the inclusion and exclusion criteria. Following quality assessment, nine of the included articles were found to be of high quality. This systematic review suggests that there has been very little research focusing on the effectiveness of manual handling training on training transfer to employees and the associated behavioural change. This review indicates that whilst employees report understanding and awareness following training, this does not always lead to the expected behavioural change. This review also suggests it cannot be demonstrated that training transfer will lead to a reduction of WRMSDs.

The effect of a backrest and seatpan inclination on sitting discomfort and trunk muscle activation in subjects with extension-related low back pain.

Few studies have demonstrated that seating modifications reduce low back pain (LBP). One recent study found that a forward-inclined seatpan reduced low back discomfort (LBD), however this was only examined in people with flexion-related LBP. No study has yet investigated its effectiveness among people with extension-related LBP. This crossover study examined 12 subjects with extension-related LBP. Sitting discomfort and surface electromyography of three trunk muscles were recorded during a 10-minute typing task while sitting with two different seatpan inclinations, both with and without a backrest. LBD (p < 0.001) and overall body discomfort (OBD) (p = 0.016) were significantly greater on the forward-inclined seatpan. The backrest did not alter trunk muscle activation or sitting discomfort. The results demonstrate that in a specific subgroup of people with extension-related LBP, increasing forward seatpan inclination significantly increased LBD and OBD. Future research should consider matching ergonomics prescriptions according to the individual presentation of people with LBP.

Effects of post-curing duration on the mechanical properties of complex 3D printed geometrical parts.

This study aims to assess the efficacy of post-curing guidance supplied by 3D printing resin manufacturers. Current guidance applies generically to all geometries with the caveat that post-curing should be extended for 'large' or 'complex' geometries but specific guidance is not provided. Two vat-polymerisation 3D printers (Form3B, Figure 4 Standalone) were used to print test models in 6 biocompatible resins (Pro Black, Med White, Med Amber, Biomed Black, Biomed White, Biomed Amber). The test model is of a complex geometry whilst also housing ISO 527 test specimens in concentric layers. Two separate intervals of curing were applied (100%, 500% stated guidance) creating different curing treatments of the specimens throughout the model. Post processed test models were disassembled and pull testing performed on each of the specimens to assess the mechanical properties. The analysis showed that extending the curing duration had significant effects on the mechanical properties of some materials but not all. The layers of the model had a significant effect except for elongation at break for the Med Amber material. This research demonstrates that generic post-curing guidance regarding UV exposures is not sufficient to achieve homogenous material strength properties for complex geometries. Large variations in mechanical properties throughout the models suggest some material was not fully-cured. This raises a query if such materials as originally marketed as biocompatible are fully cured and therefore safe to use for medical applications involving complex geometries.

Investigating the effect of real-time spinal postural biofeedback on seated discomfort in people with non-specific chronic low back pain.

A total of 24 participants with non-specific chronic low back pain (NSCLBP) sat for 2 h while their seated posture and low back discomfort (LBD) were analysed. A total of 16 pain developers (PDs), whose LBD increased by at least two points on the numeric rating scale, repeated the procedure 1 week later, while receiving postural biofeedback. PDs were older (p = 0.018), more disabled (p = 0.021) and demonstrated greater postural variability (p < 0.001). The ramping up of LBD was reduced (p = 0.002) on retesting, when sitting posture was less end-range (p < 0.001), and less variable (p = 0.032). Seated LBD appears to be related with modifiable characteristics such as sitting behaviour. Among people with sitting-related NSCLBP, the ramping up of LBD was reduced by modifying their sitting behaviour according to their individual clinical presentation. The magnitude of change, while statistically significant, was small and no follow-up of participants was completed. Further research should examine integrating biofeedback into comprehensive biopsychosocial management strategies for NSCLBP. PRACTITIONER SUMMARY: The effect of real-time postural biofeedback on LBD was examined among people with LBP. Postural biofeedback matched to the individual clinical presentation significantly reduced LBD within a single session. Further research should examine the long-term effectiveness of postural biofeedback as an intervention for LBP.

Specific flexion-related low back pain and sitting: comparison of seated discomfort on two different chairs.

No study has examined the effectiveness of prescribing seating modifications according to the individual clinical presentation of people with low back pain (LBP). A dynamic, forward-inclined chair ('Back App') can reduce seated paraspinal muscle activation among pain-free participants. This study examined 21 participants whose LBP was specifically aggravated by prolonged sitting and was eased by standing. Low back discomfort (LBD) and overall body discomfort (OBD) were assessed every 15 min while participants sat for 1 h on both the dynamic, forward-inclined chair and a standard office chair. LBD increased significantly more (p = 0.005) on the standard office chair, with no significant difference (p = 0.178) in OBD between the chairs. The results demonstrate that, in a specific flexion-related subgroup of people with LBP, increased LBD during sitting can be minimised through modifying chair design. Mechanisms that minimise seated discomfort may be of relevance in LBP management, as part of a biopsychosocial management plan. PRACTITIONER SUMMARY: This study examined low back discomfort (LBD) during a typing task among people with low back pain (LBP). Sitting on a dynamic, forward-inclined chair resulted in less seated LBD than sitting on a standard office chair. Further research is required to examine the long-term effectiveness of ergonomics interventions in LBP.