Remotely Bonded Bridging Dioxygen Ligands Enhance Hydrogen Transfer in a Silica-Supported Tetrairidium Cluster Catalyst.

A longstanding challenge in catalysis by noble metals has been to understand the origin of enhancements of rates of hydrogen transfer that result from the bonding of oxygen near metal sites. We investigated structurally well-defined catalysts consisting of supported tetrairidium carbonyl clusters with single-atom (apical iridium) catalytic sites for ethylene hydrogenation. Reaction of the clusters with ethylene and H2 followed by O2 led to the onset of catalytic activity as a terminal CO ligand at each apical Ir atom was removed and bridging dioxygen ligands replaced CO ligands at neighboring (basal-plane) sites. The presence of the dioxygen ligands caused a 6-fold increase in the catalytic reaction rate, which is explained by the electron-withdrawing capability induced by the bridging dioxygen ligands, consistent with the inference that reductive elimination is rate-determining. Electronic-structure calculations demonstrate an additional role of the dioxygen ligands, changing the mechanism of hydrogen transfer from one involving equatorial hydride ligands to that involving bridging hydride ligands. This mechanism is made evident by an inverse kinetic isotope effect observed in ethylene hydrogenation reactions with H2 and, alternatively, with D2 on the cluster incorporating the dioxygen ligands and is a consequence of quasi-equilibrated hydrogen transfer in this catalyst. The same mechanism accounts for rate enhancements induced by the bridging dioxygen ligands for the catalytic reaction of H2 with D2 to give HD. We posit that the mechanism involving bridging hydride ligands facilitated by oxygen ligands remote from the catalytic site may have some generality in catalysis by oxide-supported noble metals.

Spectroscopic Characterization of µ-η1:η1-Peroxo Ligands Formed by Reaction of Dioxygen with Electron-Rich Iridium Clusters.

Although oxygen is a common ligand in supported metal catalysts, its coordination has been challenging to elucidate. We now characterize a diiridium complex that has been previously shown by X-ray diffraction crystallography to incorporate a µ-η1:η1-peroxo ligand. We observe markedly enhanced intensity at 788 cm-1 in the Raman spectrum of this complex, which is a consequence of bonding of the peroxo ligand but does not shift upon 18O labeling. Electronic structure calculations at the density functional theory level suggest that this increase in Raman intensity results from bands associated with rocking of CH2 substituents directly attached to P(Ph)2 groups coupling with the O-O band. These results provide part of the foundation for understanding oxygen ligands on a silica-supported tetrairidium carbonyl cluster stabilized with bulky electron-donating phosphine ligands [p-tert-butyl-calix[4]arene(OPr)3(OCH2PPh2) (Ph = phenyl; Pr = propyl)]. Reaction of the cluster with O2 also led to the growing in of a Raman band at 788 cm-1, similar to that in the diiridium complex and also assigned to the bonding of a bridging peroxo ligand. Infrared spectra recorded as the supported cluster reacted in sequential exposures to (i) H2, (ii) O2, (iii) H2, and (iv) CO indicate that two bridging peroxo ligands were bonded irreversibly per tetrairidium cluster, replacing bridging carbonyl ligands without altering either the cluster frame or the phosphine ligands. X-ray absorption near edge and infrared spectra include isosbestic points signifying a stoichiometrically simple reaction of the cluster with O2, and mass spectra of the effluent gas show that CO2 formed by oxidation of one terminal CO ligand per cluster as H2 (and not H2O) formed, evidence that hydride ligands had been present on the cluster following treatment (i). The understanding of how O2 reacts with the metal polyhedron provides a foundation for understanding of how oxidation catalysis may proceed on the surfaces of noble metals.

Weakly interacting solvation spheres surrounding a calixarene-protected tetrairidium carbonyl cluster: contrasting effects on reactivity of alkane solvent and silica support.

The tetrairidium carbonyl cluster Ir4L3(CO)9 (L = tert-butyl-calix[4]arene(OPr)3(OCH2PPh2) (Ph = phenyl; Pr = propyl)) on a partially dehydroxylated silica support undergoes hydrogen activation at a rate and with a mechanism different from those pertaining to the cluster in alkane solution. These results are unobvious in view of the sterically bulky ligands protecting the cluster and the nearly identical CO band frequencies in the infrared spectra characterizing the supported and dissolved Ir4L3(CO)9, both before reaction and during reaction involving decarbonylation in the presence of either helium or H2 (and H2 reacted with the clusters to form hydrides with the same Ir-H band frequencies for clusters in alkane solvent and supported on silica). The initial rates of CO loss from the supported clusters in the presence of helium were the same as those in the presence of H2. The comparison demonstrates that the rate-determining step for hydride formation on the silica-supported cluster is CO dissociation. In contrast, the comparable dissociation of CO from the cluster in n-decane solution requires a higher temperature, 343 K, and is at least an order of magnitude slower than when the clusters were supported on silica. CO dissociation is not the rate-determining step for hydrogen activation on the cluster in n-decane, as the rate is influenced by reactant H2 as well.