Compact, remote optical waveguide magnetic field sensing using double-pass Faraday rotation-induced optical attenuation.

Compact, magnetic field, B sensing is proposed and demonstrated by combining the two Faraday rotation elements and beam displacement crystals within a micro-optical fiber circulator with a fiber reflector and ferromagnets to allow high contrast attenuation in an optical fiber arm. Low optical noise sensing is measured at λ=1550n m as a change in attenuation, α, of optical light propagating through the rotators and back. The circulator's double-pass configuration, using a gold mirror as a reflector, achieves a magnetic field sensitivity s=Δ α/Δ B=(0.26±0.02)d B/m T with a resolution of Δ B=0.01m T, over a detection range B=0-89m T. The circulator as a platform provides direct connectivity to the Internet, allowing remote sensing to occur. The method described here is amenable to multisensor combinations, including with other sensor technologies, particularly in future integrated waveguide Faraday optical circuits and devices, extending its utility beyond point magnetic field sensing applications.

Effects of a UV absorber in silica-loaded resin on DLP silica fiber preform fabrication.

3D printing technologies have distinguished advantages in manufacturing arbitrary shapes and complex structures that have attracted us to use digital light processing (DLP) technology for specialty silica optical fiber preforms. One of the main tasks is to develop an appropriate recipe for DLP resin that is UV sensitive and loaded with silica nanoparticles. In this work, the effects of a UV absorber in highly silica-loaded resin on DLP printing are experimentally investigated. Spot tests and DLP printing are carried out on resins with varying dosages of a typical UV absorber, Sudan Orange G. Based on the experimental results, the UV absorber can significantly improve the resolution of DLP printed green bodies while requiring a larger exposure dose.

Voltage, thermal and magnetic field fiber sensors based on magnetic nanoparticles-doped photonic liquid crystal fibers.

In this article, highly sensitive voltage, thermal and magnetic field fiber sensors were obtained in magnetic nanoparticles-doped E7 liquid crystals filled into photonic crystal fibers (PLCF). The voltage and temperature sensitivity reached at 12.598 nm/V and -3.874 nm/°C, respectively. The minimum voltage response time is 48.2 ms. The phase transition temperature Tc of liquid crystal with magnetic dopant was reduced from 60 °C to 46 °C. The magnetic field sensor based on magnetic nanoparticles-doped PLCF were obtained with sensitivity of 118.2 pm/mT from 400 to 460 mT.

Compact terahertz birefringent gratings for dispersion compensation.

Terahertz radiation as an upcoming carrier frequency for next-generation wireless communication systems has great potential to enable ultra-high-capacity transmissions with several tens of gigahertz bandwidths. Nevertheless, dispersion is one of the main impairments in achieving a higher bit rate. Here, we experimentally demonstrate a compact terahertz dispersion compensator based on subwavelength gratings. The gratings are fabricated from the low-loss cyclic olefin copolymer exploiting micro-machining fabrication techniques. With the strong index modulation introduced in the subwavelength grating, the high negative group velocity dispersion of -188 (-88) ps/mm/THz is achieved at 0.15 THz for x-polarization (y-polarization), i.e., 7.5 times increase compared to the state-of-the-art reported to date for terahertz. Such high negative dispersion is realized in a grating of 43 mm length. The asymmetric cross-section and periodic-structural modulation along propagation direction lead to considerable birefringence that maintains and filters two orthogonal polarization states, respectively. These polymer-based birefringent gratings can be integrated into terahertz communication systems for dispersion compensation of both long-haul wireless links and waveguide-based interconnect links.

Compact Tri-FFPI sensor for measurement of ultrahigh temperature, vibration acceleration, and strain.

As a high-precision fiber optic sensor, a single optical fiber Fabry Pérot interferometer (FFPI) sensor is often used to measure parameters such as temperature or strain. However, the use of combined FFPIs to measure multiple parameters simultaneously has rarely been reported. In this paper, a compact Tri-FFPI sensor consisting of three series-connected FFPIs is proposed to measure high temperature, high acceleration, and large strain. The total length and diameter of the sensing part are only 2558.9 µm and 250 µm, respectively. One of the FFPIs, FFPI-1, contains a cantilever beam structure to measure vibration acceleration. FFPI-2 is used to measure temperature and the temperature compensation of the strain measurement. FFPI-3 is used to measure strain. To ensure that the sensor has high measurement sensitivity, two demodulation methods are used: the light intensity demodulation method for vibration acceleration and the wavelength demodulation method for temperature and strain. The sensor is capable of withstanding ultrahigh temperatures up to 1000°C.

Joint-peaks demodulation method based on multireflection peaks of a few-mode fiber Bragg grating for reducing sensing error.

A few-mode fiber Bragg grating (FM-FBG) inscribed in a few-mode fiber (FMF) can maintain multiple reflection peaks due to the stable multiple modes in FMF. This paper studies the sensing characteristics of multiple reflection peaks for a four-mode FBG (4M-FBG) and innovatively proposes a joint-peak demodulation method based on one FM-FBG to reduce measurement error in temperature or strain sensing. This joint-peak demodulation method, theoretically explained and experimentally verified, provides the possibility of generating miniature sensors with high measurement accuracy and stable measurement performance. The potential of 4M-FBG for simultaneous measurement of strain and temperature is studied in this paper. By measuring the changes of wavelength and intensity of the reflection peaks, temperature and strain can be measured effectively.

Adaptive high-precision demodulation method based on vector matching and cluster-competitive particle swarm optimization for multiplexed FPIs.

Multiplexed fiber optic Fabry-Perot interferometer (FPI) sensors are well known for their precision, simple construction, simpler wiring, and high sensing qualities. However, the limitations on existing demodulation methods degrade the measurement accuracy of multiplexed FPI sensors and necessitate large cavity length differences. In this paper, we propose an adaptive high-precision demodulation method based on vector matching and cluster-competitive particle swarm optimization (CCPSO), which transforms cavity length demodulation into searching for the global extreme. The proposed CCPSO, which uses agglomeration within clusters and competition between clusters simultaneously, enables the improvement of the global extreme search capabilities. The theoretical analysis and experimental results show that the proposed demodulation method decreases the lower limit of the needed cavity length differences to 22 µm, which is reduced by 76.9% compared with the fast Fourier transform-based method. An accuracy of 1.05 nm is achieved with a cavity length difference of 27.5 µm and a signal-to-noise ratio of 36.0 dB for the noise.

Characterization of YAG:Ce phosphor dosimeter by the co-precipitation method for radiotherapy.

Yttrium aluminum garnet (YAG) doped with Ce was synthesized via the co-precipitation method with NH4HCO3 as the precipitant. The spectroscopic properties and the effects of the Ce doping concentration and sintering atmosphere on the crystal phase were investigated. The dosimeter of YAG:Ce phosphor material was prepared to study the radioluminescence (RL) characteristics of a clinical linear accelerator. A satisfying linear relationship between the radiation dose and RL signal was obtained, which provided a reference for the YAG:Ce phosphor material used in radiotherapy and real-time remote radiation detection.

Helical distributed feedback fiber Bragg gratings and rocking filters in a 3D printed preform-drawn fiber.

Using induced UV attenuation across a twisted fiber asymmetric core drawn from a 3D printed preform, linear fiber Bragg gratings (FBGs) are produced on one side of the core. By removing the twist, a helical grating with a period matching the twist rate is produced. Balancing the rate with the polarization beat length in a form birefringent fiber allows the production of a combined rocking filter and FBG device with tunable properties. Direct observation of the fiber grating dispersion within the rocking filter rejection band is possible.

Thermal-induced luminescence enhancement of BAC-P in bismuth-doped phosphogermanosilicate fibers.

The thermal quenching effect has been systematically investigated in bismuth (Bi)-doped phosphogermanosilicate fiber with varying thermal conditions. For the first time, to the best of our knowledge, the activation of phosphor-related Bi active center (BAC-P) is achieved by thermal quenching at 400°C with a heating time of 10 min, evidenced by the enhanced luminescence of BAC-P (${\sim}{1.3}$∼1.3 times) at 1300 nm. The experimental results reveal that a relatively low heating temperature with prolonged heating time stimulates the growth of BAC-P, whereas higher operating temperatures ($ {\ge} 500^\circ $≥500∘C) result in the irreversible destruction of BAC-P. The underlying mechanism for the thermally stimulated BAC-P process is also analyzed and discussed.

Thermal bleaching of BACs in bismuth/erbium co-doped fiber fabricated through 3D silica lithography.

Bismuth/erbium co-doped optical fiber fabricated through 3D silica lithography is thermally treated with various conditions. Then the thermal treatment effect on bismuth active centers (BACs) in this fiber is investigated. The thermal bleaching of the BAC associated with Al and the BAC associated with Si is observed after thermal treatment at high temperatures (300°C-800°C). It is found that the absorption and luminescence of BACs dramatically decrease after the thermal treatment, even totally bleaching at 700°C. The results show that the temperature and dwell time have significant effects on the thermal bleaching and activation of BACs. The underlying mechanisms of these thermal-induced effects are further discussed.

Photo-induced bleaching and thermally stimulated recovery of BAC-P in Bi-doped phosphosilicate fibers.

The first results of the study on photobleaching and thermally induced recovery in Bi-doped phosphosilicate fiber have been presented. It was revealed that the rate of bleaching of phosphor-related Bi active center (BAC-P) becomes slower with the decrease of photon energy. The quadratic dependence of the bleaching rate of BAC-P on laser power is obtained under 532 nm laser irradiation. The effect of temperature on the bleaching dynamics of BAC-P is also investigated under 532 nm radiation, suggesting a thermally aggravated bleaching process upon heating at certain temperatures (≥300∘C). Furthermore, the thermal recovery of bleached Bi-doped silica-based fiber (BDF) is investigated and a 13% increase of luminescence is achieved upon thermal quenching for 5 min at 400ºC. The underlying mechanism of photobleaching and thermo-stimulated recovery process of BAC-P is also discussed.

Impact of Al2O3 doping on Bi active center photobleaching in Bi/Er-codoped fibers.

In this Letter, the impact of Al2O3 doping on the Bi active center (BAC) photobleaching is investigated in Bi/Er-codoped fibers (BEDFs). By measuring the evolution of emission attributed to the BAC associated with silica (BAC-Si) at ∼1400nm, the linear relationship between the ratio of unbleached/bleached part (γUB/γB) and 830 nm irradiation intensity (P830) was revealed in the log-log plot. The experimental results demonstrate that Al2O3 doping or its induced defects could be one key factor exaggerating the BAC photobleaching in BEDFs.

Thermal Stability of Type II Modifications by IR Femtosecond Laser in Silica-based Glasses.

Femtosecond (fs) laser written fiber Bragg gratings (FBGs) are excellent candidates for ultra-high temperature (>800 ºC) monitoring. More specifically, Type II modifications in silicate glass fibers, characterized by the formation of self-organized birefringent nanostructures, are known to exhibit remarkable thermal stability around 1000 ºC for several hours. However, to date there is no clear understanding on how both laser writing parameters and glass composition impact the overall thermal stability of these fiber-based sensors. In this context, this work investigates thermal stability of Type II modifications in various conventional glass systems (including pure silica glasses with various Cl and OH contents, GeO2-SiO2 binary glasses, TiO2- and B2O3-doped commercial glasses) and with varying laser parameters (writing speed, pulse energy). In order to monitor thermal stability, isochronal annealing experiments (Δt⁓ 30 min, ΔT⁓ 50 ºC) up to 1400 ºC were performed on the irradiated samples, along with quantitative retardance measurements. Among the findings to highlight, it was established that ppm levels of Cl and OH can drastically reduce thermal stability (by about 200 ºC in this study). Moreover, GeO2 doping up to 17 mole% only has a limited impact on thermal stability. Finally, the relationships between glass viscosity, dopants/impurities, and thermal stability, are discussed.

Ultra-wideband and flat-gain optical properties of the PbS quantum dots-doped silica fiber.

We investigate the microstructural characteristics and optical properties of PbS quantum dots-doped silica fiber (PQDF), prepared by atomic layer deposition (ALD) doping technique. The fiber exhibits ultra-wideband luminescence and flat-gain with 3 dB bandwidth of 300 nm. The on-off gain and net gain can reach to 7.1-15.0 dB and 6.0-9.2 dB at 1050-1350 nm, respectively. The results of high-resolution transmission electron microscopy (HRTEM) further reveal the effects of PbS QDs doping in PQDF. The broadband luminescence spectrum originating from three active centers (1086, 1179, and 1304 nm), can be attributed to the dimension effect of PbS QDs (3.7, 4.0, and 4.3 nm, respectively). Moreover, the calculation results indicate that the multi-sized PbS QDs concentrated at 3.65-4.45 nm make the 3 dB gain bandwidth increase, which is six times wider than that of traditional erbium-doped fiber (EDF). Therefore, this type of PQDF is a promising gain medium for optical amplifiers and broadband light sources.

Effect of thermal treatment parameters on the spectral characteristics of BAC-Al in bismuth/erbium-codoped aluminosilicate fibers.

For the first time, to the best of our knowledge, the effect of thermal quenching on the spectral properties of bismuth-related active centers (BAC)-Al is investigated systematically with varying quenching conditions. It is found that the peak luminescence of BAC-Al at 1140 nm is maximally enhanced by 1.6 times with a heating dwell time of 2 min at 500°C and subsequent quenching, suggesting that a short dwell time with a high heating temperature (500°C) favors the activation or growth of BAC-Al, whereas the prolonged heating time with a slow cooling rate results in the deactivation of BACs and the aggregation of background loss. The underlying mechanism of activation and destruction of BAC-Al is also analyzed and discussed. The experimental results demonstrate a promising strategy for enhancing the spectral performance of BAC-Al in the range of 1.1-1.35 µm.

Effect of pump wavelength and temperature on the spectral performance of BAC-Al in bismuth-doped aluminosilicate fibers.

The near-infrared luminescence of Bi-doped aluminosilicate fiber within pump wavelengths between 710 and 990 nm and under varying pump powers and operation temperatures has been investigated systematically. It is revealed that there exist two emission bands peaking around 1120 and at 1300 nm, which are believed to be associated with two different aluminum-related bismuth active centers (BAC-Al1 and BAC-Al2); the BAC-Al2 is found to be more efficiently excited at a lower temperature within the spectral range of 790-850 nm. This is the first time, to the best of our knowledge, that two sub-bands of BAC-Al are identified. The thermal annealing effect on the luminescence of BACs is also studied under 830 nm pumping. In contrast to the quenching of BAC-Si, the luminescence intensity of BAC-Al1 is enhanced by 1.5 times after 500°C heating and subsequent cooling. The results demonstrate an effective strategy for tuning the emission scheme in the range of 1100-1400 nm by adjusting the excitation wavelength and operation temperature.

Silica optical fiber drawn from 3D printed preforms.

Silica optical fiber was drawn from a three-dimensional printed preform. Both single mode and multimode fibers are reported. The results demonstrate additive manufacturing of glass optical fibers and its potential to disrupt traditional optical fiber fabrication. It opens up fiber designs for novel applications hitherto not possible.

Thermally aggravated photo-bleaching of BAC-Al in bismuth/erbium co-doped optical fiber.

The thermal effect upon the photo-bleaching of bismuth/erbium co-doped optical fiber (BEDF) containing Al has been investigated. The photo-bleaching effects of aluminum related bismuth active center (BAC-Al) in BEDF are studied from room temperature (RT) up to 350°C under the irradiation of a 980 nm laser. No visible bleaching of the luminescence associated with BAC-Al was observed at RT, but significant bleaching appeared at higher temperatures above 150°C under the same irradiation power. The underlying mechanism of significant thermal aggravation of photo-bleaching is discussed, and its impact needs to be considered in the design and application of optical amplifiers and lasers using Al-doped BEDF.

BAC activation by thermal quenching in bismuth/erbium codoped fiber.

We have investigated the thermal quenching effect on the bismuth active center (BAC) in a Bi/Er co-doped fiber (BEDF). The effects from varying quenching conditions are studied and discussed. We report, for the first time to our knowledge, a significant BAC activation achieved by thermal quenching. We observed that the peak luminescence at ∼1405 nm of the BAC associated with silica (BAC-Si) could be enhanced more than two times by thermal quenching. The experimental results indicate that thermal quenching could be an effective way for BAC activation of bismuth-doped fibers.