Glycerol Valorization towards a Benzoxazine Derivative through a Milling and Microwave Sequential Strategy.

Glycerol and aminophenol intermolecular condensation has been investigated through a milling and microwave-assisted sequential strategy, towards the synthesis of a benzoxaxine derivative. Mechanochemical activation prior to the microwave-assisted process could improve the probability of contact between the reagents, and greatly favors the higher conversion of aminophenol. At the same time, following a mechanochemical-microwave sequential approach could tune the selectivity towards the formation of a benzoxazine derivative, which could find application in a wide range of biomedical areas.

Single-Step Methylation of Chitosan Using Dimethyl Carbonate as a Green Methylating Agent.

N,N,N-Trimethyl chitosan (TMC) is one chitosan derivative that, because of its improved solubility, has been studied for industrial and pharmaceutic applications. Conventional methods for the synthesis of TMC involve the use of highly toxic and harmful reagents, such as methyl iodide and dimethyl sulfate (DMS). Although the methylation of dimethylated chitosan to TMC by dimethyl carbonate (DMC, a green and benign methylating agent) was reported recently, it involved a formaldehyde-based procedure. In this paper we report the single-step synthesis of TMC from chitosan using DMC in an ionic liquid. The TMC synthesised was characterised by 1H NMR spectroscopy and a functionally meaningful degree of quaternisation of 9% was demonstrated after a 12-h reaction time.

Precursor-Dependent Photocatalytic Activity of Carbon Dots.

This work systematically compares both structural features and photocatalytic performance of a series of graphitic and amorphous carbon dots (CDs) prepared in a bottom-up manner from fructose, glucose, and citric acid. We demonstrate that the carbon source and synthetic procedures diversely affect the structural and optical properties of the CDs, which in turn unpredictably influence their photo electron transfer ability. The latter was evaluated by studying the photo-reduction of methyl viologen. Overall, citric acid-CDs were found to provide the best photocatalytic performance followed by fructose- and glucose-CDs. However, while the graphitization of glucose- and citric acid-CDs favored the photo-reaction, a reverse structure-activity dependence was observed for fructose-CDs due to the formation of a large graphitic-like supramolecular assembly. This study highlights the complexity to design in advance photo-active bio-based carbon nanomaterials.

Towards a Rational Design of a Continuous-Flow Method for the Acetalization of Crude Glycerol: Scope and Limitations of Commercial Amberlyst 36 and AlF3·3H2O as Model Catalysts.

The acetalization of six different types of glycerol including pure, wet, and crude-like grade compounds of compositions simulating those of crude glycerols produced by the biodiesel manufacture, was carried out with two model ketones such as acetone and 2-butanone. The reaction was investigated under continuous-flow (CF) conditions through a comparative analysis of an already known acetalization catalyst such as Amberlyst 36 (A36), and aluminum fluoride three hydrate (AlF3·3H2O, AF) whose use was never previously reported for the synthesis of acetals. At 10 bar and 25 °C, A36 was a highly active catalyst allowing good-to-excellent conversion (85%-97%) and selectivity (99%) when either pure or wet glycerol was used as a reagent. This catalyst however, proved unsuitable for the CF acetalization of crude-like glycerol (CG) since it severely and irreversibly deactivated in a few hours by the presence of low amounts of NaCl (2.5 wt %) which is a typical inorganic impurity of raw glycerol from the biorefinery. Higher temperature and pressure (up to 100 °C and 30 bar) were not successful to improve the outcome. By contrast, at 10 bar and 100 °C, AF catalyzed the acetalization of CG with both acetone and 2-butanone, yielding stable conversion and productivity up to 78% and 5.6 h(-1), respectively. A XRD analysis of fresh and used catalysts proved that the active phase was a solid solution (SS) of formula Al2[F1-x(OH)x]6(H2O)y present as a component of the investigated commercial AF sample. A hypothesis to explain the role of such SS phase was then formulated based on the Brønsted acidity of OH groups of the solid framework. Overall, the AF catalyst allowed not only a straightforward upgrading of CG to acetals, but also a more cost-efficient protocol avoiding the expensive refining of raw glycerol itself.

Synthesis of the Fatty Esters of Solketal and Glycerol-Formal: Biobased Specialty Chemicals.

The caprylic, lauric, palmitic and stearic esters of solketal and glycerol formal were synthesized with high selectivity and in good yields by a solvent-free acid catalyzed procedure. No acetal hydrolysis was observed, notwithstanding the acidic reaction conditions.

Ionic liquids as transesterification catalysts: applications for the synthesis of linear and cyclic organic carbonates.

The use of ionic liquids (ILs) as organocatalysts is reviewed for transesterification reactions, specifically for the conversion of nontoxic compounds such as dialkyl carbonates to both linear mono-transesterification products or alkylene carbonates. An introductory survey compares pros and cons of classic catalysts based on both acidic and basic systems, to ionic liquids. Then, innovative green syntheses of task-specific ILs and their representative applications are introduced to detail the efficiency and highly selective outcome of ILs-catalyzed transesterification reactions. A mechanistic hypothesis is discussed by the concept of cooperative catalysis based on the dual (electrophilic/nucleophilic) activation of reactants.

Carbonate phosphonium salts as catalysts for the transesterification of dialkyl carbonates with diols. The competition between cyclic carbonates and linear dicarbonate products.

At 90-120 °C, in the presence of methylcarbonate and bicarbonate methyltrioctylphosphonium salts as catalysts ([P8881][A]; [A] = MeOCO2 and HOCO2), the transesterification of non-toxic dimethyl- and diethyl-carbonate (DMC and DEC, respectively) with 1,X-diols (2 ≤ X ≤ 6) proceeds towards the formation of cyclic and linear products. In particular, 1,2-propanediol and ethylene glycol afford propylene- and ethylene-carbonate with selectivity and yields up to 95 and 90%, respectively; while, the reaction of DMC with higher diols such 1,3-butanediol, 2-methyl-1,3-propanediol, 1,3-propanediol, 2,2-dimethyl, 1,3-propanediol, 1,4-butanediol and 1,6-hexanediol produce linear C8-C10 dicarbonates of general formula MeOC(O)O∼∼∼OC(O)OMe as the almost exclusive products. Of note, these dicarbonate derivatives are not otherwise accessible in good yields by other conventional base catalyzed methods. Among 1,3-diols, the only exception was 2-methyl 2,4-pentandiol that yields the corresponding cyclic carbonate, i.e. 4,4,6-trimethyl-1,3-dioxan-2-one. In no one case, polycarbonates are observed. Such remarkable differences of product distributions are ascribed to the structure (branching and relative position of OH groups) of diols and to the role of cooperative (nucleophilic and electrophilic) catalysis which has been proved for onium salts. The investigated carbonate salts are not only effective in amounts as low as 0.5 mol%, but they are highly stable and recyclable.

Green extraction of chitin from hard spider crab shells.

A green protocol to extract chitin from crab shells using water soluble ionic liquids (ILs) is here reported. Compared to conventional multistep acid-base extraction methods, this one-pot procedure achieves pulping of recalcitrant crustacean waste shells by employing ammonium acetate, ammonium formate and hydroxylammonium acetate as water-soluble, low-cost and easy to prepare ILs. An extensive parametric analysis of the pulping process has been carried out with different ILs, different ratios, temperature and time. The optimized protocol provides a high-quality chitin comparable, if not better, to commercial chitin. The best results were obtained at 150 °C with ammonium formate prepared in-situ from aqueous ammonia and formic acid: chitin was isolated in a 17 wt% yield (based on dried crab shells as starting biowaste), a degree of acetylation (DA) > 94 %, a crystallinity index of 39-46 %, a molecular weight up to 6.6 × 105 g/mol and a polydispersity of ca 2.0.

Selective Multiphase-Assisted Oxidation of Bio-Sourced Primary Alcohols over Ru- and Mo- Carbon Supported Catalysts.

The oxidation of representative bio-based benzyl-type alcohols has been successfully carried out in a multiphase (MP) system comprised of three mutually immiscible liquid components as water, isooctane, and a hydrophobic ionic liquid as methyltrioctylammonium chloride ([N8881][Cl]), a heterogeneous catalyst (either ad-hoc synthesized carbon-supported Mo or a commercial 5% Ru/C), and air as an oxidant. The MP-reaction proceeded as an interfacial process with Mo/C or Ru/C perfectly segregated in the ionic liquid phase and the reactant(s)/products(s) dissolved in the aqueous solution. This environment proved excellent to convert quantitatively benzyl alcohols into the corresponding aldehydes with a selectivity up to 99%, without overoxidation to carboxylic acids. The nature of the catalyst, however, affected the operating conditions with Ru/C active at a lower T and t (130 °C, 4-6 h) compared to Mo/C (150 °C, 24 h). The phase confinement was advantageous also to facilitate the products isolation and the recycle of the catalyst. Notably, in the Mo/C-catalyzed oxidation of benzyl alcohol, benzaldehyde was achieved with unaltered selectivity (>99%) at complete conversion, for 5 subsequent reactions through a semicontinuous procedure in which the catalyst was reused in-situ, without ever removing it from the reactor or treating it in any way.

UPCYCLING OF CHITIN TO CROSS-COUPLING CATALYSTS: TAILORED SUPPORTS AND OPPORTUNITIES IN MECHANOCHEMISTRY.

In this study chitin derived from shrimp shells was used in the design of heterogeneous Pd-based catalysts for Heck and Suzuki-Miyaura cross-coupling reactions. The synthesis of Pd nanoparticles supported on N-doped carbons was performed through different approaches, including a sustainable mechanochemical approach, by using a twin-screw extruder. All catalytic systems were characterized by a multitechnique approach and the effect of nanoparticles size, N-doping on the support, and their synergistic interactions were elucidated. Specifically, Kelvin Probe Atomic Force Microscopy provided valuable insights on charge transfer and metal-support interactions. The catalytic behaviour of the samples was investigated in cross-coupling reactions under batch conditions and under semi-continuous flow solvent-free conditions, respectively obtaining a quantitative yield and a noteworthy productivity of 8.7 mol/(gPdh).

Chitin-Derived Nanocatalysts for Reductive Amination Reactions.

Chitin, the second most abundant biopolymer in the planet after cellulose, represents a renewable carbon and nitrogen source. A thrilling opportunity for the valorization of chitin is focused on the preparation of biomass-derived N-doped carbonaceous materials. In this contribution, chitin-derived N-doped carbons were successfully prepared and functionalized with palladium metal nanoparticles. The physicochemical properties of these nanocomposites were investigated following a multi-technique strategy and their catalytic activity in reductive amination reactions was explored. In particular, a biomass-derived platform molecule, namely furfural, was upgraded to valuable bi-cyclic compounds under continuous flow conditions.

Methylcarbonate and bicarbonate phosphonium salts as catalysts for the nitroaldol (Henry) reaction.

Phosphonium ionic liquids exchanged with bicarbonate and methylcarbonate anions (CILs) exhibit catalytic performances comparable to those of sterically hindered (non nucleophilic) organosuperbases such as DBU. At 25-50 °C, under solventless conditions, CILs efficiently catalyze the Henry addition of different aldehydes and ketones to nitroalkanes: not only they allow the selective formation of nitroaldols but they unlock a novel high-yielding access to dinitromethyl derivatives of ketones.

Carbonate, acetate and phenolate phosphonium salts as catalysts in transesterification reactions for the synthesis of non-symmetric dialkyl carbonates.

Methyl trioctylphosphonium methyl carbonate [P(8881)](+)[MeOCO(2)](-) was prepared by the alkylation of trioctyl phosphine with the non-toxic dimethyl carbonate. This salt was a convenient source to synthesize different ionic liquids where the methyl trioctylphosphonium cation was coupled to weakly basic anions such as bicarbonate, acetate, and phenolate. At 90-220 °C, all these compounds [P(8881)](+)X(-); X = MeOCO(2); HOCO(2); AcO; PhO were excellent organocatalysts for the transesterification of dimethyl and diethyl carbonate with primary and secondary alcohols, including benzyl alcohol, cyclopentanol, cyclohexanol, and the rather sterically hindered menthol. Conditions were optimized to operate with very low catalyst loadings up to 1 mol% and to obtain non-symmetric dialkyl carbonates (ROCO(2)R'; R = Me, Et) with selectivity up to 99% and isolated yields >90%. The catalytic performance of the investigated ionic liquids was discussed through a cooperative mechanism of simultaneous activation of both electrophilic and nucleophilic reactants.

Fish-Waste-Derived Gelatin and Carbon Dots for Biobased UV-Blocking Films.

The fish industry produces every year huge amounts of waste that represent an underutilized source of chemical richness. In this contribution, type I collagen was extracted from the scales of Mugil cephalus and carbon dots (CDs) were synthesized from the scales of Dicentrarchus labrax. These materials were combined to make hybrid films with UV-blocking ability, by casting a mixture of gelatin, glycerol (15%), and CDs (0, 1, 3, and 5%). The films were fully characterized from the mechanical, morphological, and optical point of view. Here, 40 µm thick films were obtained, characterized by a high water solubility (70%); moreover, the presence of CDs improved the film mechanical properties, in particular increasing the tensile strength (TS) up to 17 MPa and elongation at break (EAB) up to 40%. The CDs also modulated water vapor permeability and the thermal stability of the films. From the optical point of view, with just 5% loading of CDs the films blocked almost 70% of the UV radiation with negligible change in transparency (88.6% for the nonloaded vs 84.4% for 5% CDs) and opacity (1.32 for nonloaded vs 1.61 for 5% CDs). These types of hybrid biobased films hold promise for the production of sustainable UV-shields both for human health and for prolonging the shelf life of food.

Tunable Multi-Phase System for Highly Chemo-Selective Oxidation of Hydroxymethyl-Furfural.

Three different multiphase systems (MP 1-3) comprised of two immiscible liquids, with or without an ionic liquid (IL: methyltrioctyl ammonium chloride), were investigated for the oxidation of 5-hydroxymethyl-furfural (HMF) over 5 % Ru/C as a catalyst and air (8 bar) as an oxidant. These conditions proved versatile for an excellent control of the reaction selectivity to 4 distinct products derived from full or partial oxidation of the carbonyl and alcohol functions of HMF, and each one achieved in 87-96 % isolated yield at complete conversion. MP1 based on water and isooctane, yielded 2,5-furandicarboxylic acid (FDCA, 91 % yield). In MP2, obtained by adding the IL to MP1, the oxidation proceeded towards the formation of 5-formyl-2-furancarboxylic acid (FFCA, 87-89 % yield). MP2 also proved successful in the design of a one pot-two step oxidation/reduction sequence to prepare 5-hydroxymethyl-2-furancarboxylic acid (HMFCA, 85 % yield). In MP3, the use of an acetonitrile/cyclooctane biphase yielded 2,5-diformylfuran (DFF, 96 % yield). All the multiphase systems MP 1-3 allowed a perfect segregation of the catalyst in a single phase (either the hydrocarbon or the IL) distinct from the one containing HMF and its oxidation products. This was crucial not only for the catalyst/product separation but also for the recycle of Ru/C that was possible under all the tested conditions. Accordingly, MP-reaction were run in a semicontinuous mode without removing the catalyst from the reactor nor resorting to conventional separation and activation techniques. Negligible Ru leaching, less than 0.96 ppb, was measured in all cases.

Tuning the Selectivity of the Hydrogenation/Hydrogenolysis of 5-Hydroxymethylfurfural under Batch Multiphase and Continuous-Flow Conditions.

The hydrogenation/hydrogenolysis of 5-hydroxymethylfurfural (HMF) has been carried out either under single (aqueous) phase or batch multiphase (MP) conditions using mutually immiscible aqueous/hydrocarbon phases, 5 % Ru/C as a catalyst, and both with and without the use of trioctylmethyl phosphonium bis-(trifluoro methane) sulfonimide ([P8881 ][NTf2 ]) as an ionic liquid (IL). Alternatively, the hydrogenation of HMF was explored in the continuous-flow (CF) mode with the same catalyst. By changing reaction parameters, experiments were optimized towards the formation of three products: 2,5-bis(hydroxy methyl)furan (BHMF), 2,5-bis(hydroxymethyl)tetrahydrofuran (BHMTHF), and 1-hydroxyhexane-2,5-dione (HHD), which were obtained in up to 92, 90, and 99 % selectivity, respectively, at quantitative conversion. In particular, the single (aqueous) phase reaction of HMF (0.2 m) carried out for 18 h at 60 °C under 30 bar of H2 , allowed the exclusive synthesis of BHMF from the partial (carbonyl) hydrogenation of HMF, while the MP reaction run at a higher T and p (100 °C and 50 bar) proved excellent to achieve only HHD derived from a sequence of hydrogenation/hydrogenolysis. It is worth noting that under MP conditions, the catalyst was perfectly segregated in the IL, where it could be recycled without any leaching in the aqueous/hydrocarbon phases. Finally, the hydrogenation of HMF was explored in a H-Cube® flow reactor in the presence of different solvents, such as ethyl acetate, tetrahydrofuran, and ethanol. At 100 °C, 50 bar H2 , and a flow rate of 0.1 mL min-1 , the process was optimized towards the formation of the full hydrogenation product BHMTHF. Ethyl acetate proved the best solvent.

Metal-Free N-Doped Carbons for Solvent-Less CO2 Fixation Reactions: A Shrimp Shell Valorization Opportunity.

High anthropogenic CO2 emissions are among the main causes of climate change. Herein, we investigate the use of CO2 for the synthesis of organic cyclic carbonates on metal-free nitrogen-doped carbon catalysts obtained from chitosan, chitin, and shrimp shell wastes, both in batch and in continuous flow (CF). The catalysts were characterized by N2 physisorption, CO2-temperature-programmed desorption, X-ray photoelectron spectroscopy, scanning electron microscopy, and CNHS elemental analysis, and all reactivity tests were run in the absence of solvents. Under batch conditions, the catalyst obtained by calcination of chitin exhibited excellent performance in the conversion of epichlorohydrin (selected as a model epoxide), resulting in the corresponding cyclic carbonate with 96% selectivity at complete conversion, at 150 °C and 30 bar CO2, for 4 h. On the other hand, in a CF regime, a quantitative conversion and a carbonate selectivity >99% were achieved at 150 °C, by using the catalyst obtained from shrimp waste. Remarkably, the material displayed an outstanding stability over a reaction run time of 180 min. The robustness of the synthetized catalysts was confirmed by their good operational stability and reusability: ca. (75 ± 3)% of the initial conversion was achieved/retained by all systems, after six recycles. Also, additional batch experiments proved that the catalysts were successful on different terminal and internal epoxides.

N-Doped Carbon Dot Hydrogels from Brewing Waste for Photocatalytic Wastewater Treatment.

The brewery industry annually produces huge amounts of byproducts that represent an underutilized, yet valuable, source of biobased compounds. In this contribution, the two major beer wastes, that is, spent grains and spent yeasts, have been transformed into carbon dots (CDs) by a simple, scalable, and ecofriendly hydrothermal approach. The prepared CDs have been characterized from the chemical, morphological, and optical points of view, highlighting a high level of N-doping, because of the chemical composition of the starting material rich in proteins, photoluminescence emission centered at 420 nm, and lifetime in the range of 5.5-7.5 ns. With the aim of producing a reusable catalytic system for wastewater treatment, CDs have been entrapped into a polyvinyl alcohol matrix and tested for their dye removal ability. The results demonstrate that methylene blue can be efficiently adsorbed from water solutions into the composite hydrogel and subsequently fully degraded by UV irradiation.

Carbon dots for cancer nanomedicine: a bright future.

Cancer remains one of the main causes of death in the world. Early diagnosis and effective cancer therapies are required to treat this pathology. Traditional therapeutic approaches are limited by lack of specificity and systemic toxicity. In this scenario, nanomaterials could overcome many limitations of conventional approaches by reducing side effects, increasing tumor accumulation and improving the efficacy of drugs. In the past few decades, carbon nanomaterials (i.e., fullerenes, carbon nanotubes, and carbon dots) have attracted significant attention of researchers in various scientific fields including biomedicine due to their unique physical/chemical properties and biological compatibility and are among the most promising materials that have already changed and will keep changing human life. Recently, because of their functionalization and stability, carbon nanomaterials have been explored as a novel tool for the delivery of therapeutic cancer drugs. In this review, we present an overview of the development of carbon dot nanomaterials in the nanomedicine field by focusing on their synthesis, and structural and optical properties as well as their imaging, therapy and cargo delivery applications.

Biobased Carbon Dots: From Fish Scales to Photocatalysis.

The synthesis, characterization and photoreduction ability of a new class of carbon dots made from fish scales is here described. Fish scales are a waste material that contains mainly chitin, one of the most abundant natural biopolymers, and collagen. These components make the scales rich, not only in carbon, hydrogen and oxygen, but also in nitrogen. These self-nitrogen-doped carbonaceous nanostructured photocatalyst were synthesized from fish scales by a hydrothermal method in the absence of any other reagents. The morphology, structure and optical properties of these materials were investigated. Their photocatalytic activity was compared with the one of conventional nitrogen-doped carbon dots made from citric acid and diethylenetriamine in the photoreduction reaction of methyl viologen.