Oxidative Spin-Spray-Assembled Coordinative Multilayers as Platforms for Capacitive Films.

The spin-spray-assisted layer-by-layer (LbL) assembly technique was used to prepare coordinative oxidative multilayers from Ce(IV), inorganic polyphosphate (PP), and graphene oxide (GO). The films consist of successive tetralayers and have a general structure (PP/Ce/GO/Ce)n. Such oxidative multilayers have been shown to be a general platform for the electrodeless generation of conducting polymer and melanin-type films. Although the incorporation of GO enhances the film growth, the conventional dip LbL method is very time consuming. We show that the spin-spray method reduces the time required to grow thick multilayers by the order of magnitude and the film growth is linear from the beginning, which implies a stratified structure. We have deposited poly(3,4-ethylenedioxothiophene), PEDOT, on the oxidative multilayers and studied these redox-active films as models for melanin-type capacitive layers for supercapacitors to be used in biodegradable electronics, both before and after the electrochemical reduction of GO to rGO. The amount of oxidant and PEDOT scales linearly with the film thickness, and the charge transfer kinetics is not mass transfer-limited, especially after the reduction of GO. The areal capacitance of the films grows linearly with the film thickness, reaching a value of ca. 1.6 mF cm-2 with 20 tetralayers, and the specific volumetric (per film volume) and mass (per mass of PEDOT) capacitances are ca. 130 F cm-3 and 65 F g-1, respectively. 5,6-Dihydroxyindole can also be polymerized to a redox-active melanin-type film on these oxidative multilayers, with even higher areal capacitance values.

Oxidative Layer-By-Layer Multilayers Based on Metal Coordination: Influence of Intervening Graphene Oxide Layers.

Layer-by-layer (LbL) fabricated oxidative multilayers consisting of successive layers of inorganic polyphosphate (PP) and Ce(IV) can electrolessly form thin conducting polymer films on their surface. We describe the effect of substituting every second PP layer in the (PP/Ce) multilayers for graphene oxide (GO) as a means of modifying the structure and mechanical properties of these (GO/Ce/PP/Ce) films and enhancing their growth. Both types of LbL films are based on reversible coordinative bonding between the metal ions and the oxygen-bearing groups in PP and GO, instead of purely electrostatic interactions. The GO incorporation leads to the doubling of the areal mass density and to a dry film thickness close to 300 nm after 4 (GO/Ce/PP/Ce) tetralayers. The film roughness increases significantly with thickness. The (PP/Ce) films are soft materials with approximately equal shear storage and loss moduli, but the incorporation of GO doubles the storage modulus. PP displays a marked terminating layer effect and practically eliminates mechanical losses, making the (GO/Ce/PP/Ce) films almost pure soft elastomers. The smoothness of the (PP/Ce) films and the PP-termination effects are attributed to the reversible coordinative bonding. The (GO/Ce/PP/Ce) films oxidize pyrrole and 3,4-ethylenedioxythiophene (EDOT) and form polypyrrole and PEDOT films on their surfaces. These polymer films are considerably thicker than those formed using the (PP/Ce) multilayers with the same nominal amount of cerium layers. The GO sheets interfere with the polymerization reaction and make its kinetics biphasic. The (GO/Ce) multilayers without PP are brittle and thin.

Effective Shielding of NaYF4:Yb3+,Er3+ Upconverting Nanoparticles in Aqueous Environments Using Layer-by-Layer Assembly.

Aqueous solutions are the basis for most biomedical assays, but they quench the upconversion luminescence significantly. Surface modifications of upconverting nanoparticles are vital for shielding the obtained luminescence. Modifications also provide new possibilities for further use by introducing attaching sites for biomolecule conjugation. We demonstrate the use of a layer-by-layer surface modification method combining varying lengths of negatively charged polyelectrolytes with positive neodymium ions in coating the upconverting NaYF4:Yb3+,Er3+ nanoparticles. We confirmed the formation of the bilayers and investigated the surface properties with Fourier transform infrared and reflectance spectroscopy, thermal analysis, and ζ-potential measurements. The effect of the coating on the upconversion luminescence properties was characterized, and the bilayers with the highest improvement in emission intensity were identified. In addition, studies for the nanoparticle and surface stability were carried out in aqueous environments. It was observed that the bilayers were able to shield the materials' luminescence from quenching also in the presence of phosphate buffer that is currently considered the most disruptive environment for the nanoparticles.

Preparation of Thin Melanin-Type Films by Surface-Controlled Oxidation.

The preparation of thin melanin films suitable for applications is challenging. In this work, we present a new alternative approach to thin melanin-type films using oxidative multilayers prepared by the sequential layer-by-layer deposition of cerium(IV) and inorganic polyphosphate. The interfacial reaction between cerium(IV) in the multilayer and 5,6-dihydroxyindole (DHI) in the adjacent aqueous solution leads to the formation of a thin uniform film. The oxidation of DHI by cerium(IV) proceeds via known melanin intermediates. We have characterized the formed DHI-melanin films using scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), UV-vis spectroscopy, and spectroelectrochemistry. When a five-bilayer oxidative multilayer is used, the film is uniform with a thickness of ca. 10 nm. Its chemical composition, as determined using XPS, is typical for melanin. It is also redox active, and its oxidation occurs in two steps, which can be assigned to semiquinone and quinone formation within the indole structural motif. Oxidative multilayers can also oxidize dopamine, but the reaction stops at the dopamine quinone stage because of the limited amount of the multilayer-based oxidizing agent. However, dopamine oxidation by Ce(IV) was studied also in solution by UV-vis spectroscopy and mass spectrometry in order to verify the reaction mechanism and the final product. In solution, the oxidation of dopamine by cerium shows that the indole ring formation takes place already at low pH and that the mass spectrum of the final product is practically identical with that of commercial melanin. Therefore, layer-by-layer formed oxidative multilayers can be used to deposit functional melanin-type thin films on arbitrary substrates by a surface-controlled reaction.

Developing Solution-Processed Distributed Bragg Reflectors for Microcavity Polariton Applications.

Improving the performance of organic optoelectronics has been under vigorous research for decades. Recently, polaritonics has been introduced as a technology that has the potential to improve the optical, electrical, and chemical properties of materials and devices. However, polaritons have been mainly studied in optical microcavities that are made by vacuum deposition processes, which are costly, unavailable to many, and incompatible with printed optoelectronics methods. Efforts toward the fabrication of polariton microcavities with solution-processed techniques have been utterly absent. Herein, we demonstrate for the first time strong light-matter coupling and polariton photoluminescence in an organic microcavity consisting of an aluminum mirror and a distributed Bragg reflector (DBR) made by sequential dip coating of titanium hydroxide/poly(vinyl alcohol) (TiOH/PVA) and Nafion films. To fabricate and develop the solution-processed DBRs and microcavities, we automatized a dip-coating device that allowed us to produce sub-100 nm films consistently over many dip-coating cycles. Owning to the solution-based nature of our DBRs, our results pave the way to the realization of polariton optoelectronic devices beyond physical deposition methods.

Surface chemistry, reactivity, and pore structure of porous silicon oxidized by various methods.

Oxidation is the most commonly used method of passivating porous silicon (PSi) surfaces against unwanted reactions with guest molecules and temporal changes during storage or use. In the present study, several oxidation methods were compared in order to find optimal methods able to generate inert surfaces free of reactive hydrides but would cause minimal changes in the pore structure of PSi. The studied methods included thermal oxidations, liquid-phase oxidations, annealings, and their combinations. The surface-oxidized samples were studied by Fourier transform infrared spectroscopy, isothermal titration microcalorimetry, nitrogen sorption, ellipsometry, X-ray diffraction, electron paramagnetic resonance spectroscopy, and scanning electron microscopy imaging. Treatment at high temperature was found to have two advantages. First, it enables the generation of surfaces free of hydrides, which is not possible at low temperatures in a liquid or a gas phase. Second, it allows the silicon framework to partially accommodate a volume expansion because of oxidation, whereas at low temperature the volume expansion significantly consumes the free pore volume. The most promising methods were further optimized to minimize the negative effects on the pore structure. Simple thermal oxidation at 700 °C was found to be an effective oxidation method although it causes a large decrease in the pore volume. A novel combination of thermal oxidation, annealing, and liquid-phase oxidation was also effective and caused a smaller decrease in the pore volume with no significant change in the pore diameter but was more complicated to perform. Both methods produced surfaces that were not found to react with a model drug cinnarizine in isothermal titration microcalorimetry experiments. The study enables a reasonable choice of oxidation method for PSi applications.

Effect of Water on a Hydrophobic Deep Eutectic Solvent.

Deep eutectic solvents (DESs) formed by hydrogen bond donors and acceptors are a promising new class of solvents. Both hydrophilic and hydrophobic binary DESs readily absorb water, making them ternary mixtures, and a small water content is always inevitable under ambient conditions. We present a thorough study of a typical hydrophobic DES formed by a 1:2 mole ratio of tetrabutyl ammonium chloride and decanoic acid, focusing on the effects of a low water content caused by absorbed water vapor, using multinuclear NMR techniques, molecular modeling, and several other physicochemical techniques. Already very low water contents cause dynamic nanoscale phase segregation, reduce solvent viscosity and fragility, increase self-diffusion coefficients and conductivity, and enhance local dynamics. Water interferes with the hydrogen-bonding network between the chloride ions and carboxylic acid groups by solvating them, which enhances carboxylic acid self-correlation and ion pair formation between tetrabutyl ammonium and chloride. Simulations show that the component molar ratio can be varied, with an effect on the internal structure. The water-induced changes in the physical properties are beneficial for most prospective applications but water creates an acidic aqueous nanophase with a high halide ion concentration, which may have chemically adverse effects.

Copolymers of bipyridinium and metal (Zn & Ni) porphyrin derivatives; theoretical insights and electrochemical activity towards CO2.

This study reports the electropolymerization of novel keto functionalized octaethyl metal porphyrins (Zn2+ and Ni2+) in the presence of 4,4'-bipyridine (4,4'-bpy) as a bridging nucleophile. The polymer films were characterized by electrochemical, spectroscopic (UV-Vis, XPS, FT-IR and Raman spectroscopy) and imaging (AFM and SEM) techniques. The absorption and electronic spectra confirm the presence of both porphyrin and 4,4'-bipyridine units in the film. The surface morphology reveals homogeneous film deposition with average roughness values of approx. 8 nm. The theoretical studies performed offered insights into the interplay of different metal centres (Zn2+ and Ni2+) and the keto functionality of the porphyrin unit in the formation of copolymer films. The electrochemical interaction of polymer films with CO2 suggests a reversible trap and release of CO2 with low energy barriers for both the polymers.

Influence of synthetic polyelectrolytes on the growth and properties of hyaluronan-chitosan multilayers.

Both hyaluronan (HA) and chitosan (CHI) are biocompatible polysaccharide electrolytes. The multilayers formed by these polyelectrolytes alone are known to be rather soft and strongly viscoelastic. In this work we study multilayers formed by incorporating synthetic nonsaccharide polyelectrolytes such as polyallylamine (PAH) and poly(acrylic acid) (PAA) in various proportions into the HA/CHI layers. The buildup was followed on a quartz crystal resonator. Surface acoustic impedance recorded in these measurements, in suitable conditions, gives a spiral when plotted in the complex plane. The shape of this spiral depends on the viscoelasticity of the layer material and regularity of the growth process. We found that poly(acrylic acid) destroys the soft diffuse matrix formed by hyaluronan. It forms diffusion barriers when deposited sparsely between the layers. If its proportion is higher, the film growth adopts a linear buildup in the layer-by-layer process. The linear buildup of CHI/PAA reveals that the buildup regime of a multilayer film does not determine the viscoelastic properties of the film. Linearly and exponentially growing films may have very similar mechanical properties. Polyacrylic acid forms a kind of scaffold inside the film giving the natively soft hyaluronan/chitosan film more mechanical strength. The optimal combination gave more than 100-fold increase in the shear modulus.

Restraining fluoride loss from NaYF4:Yb3+,Er3+ upconverting nanoparticles in aqueous environments using crosslinked poly(acrylic acid)/poly(allylamine hydrochloride) multilayers.

The use of upconverting nanoparticles in various applications in aqueous media relies on their surface modifications as most synthesis routes yield hydrophobic particles. However, introducing upconverting nanoparticles in aqueous solutions commonly results in the quenching of their luminescence intensity and in the worst case, disintegration of the nanoparticles. We demonstrate the use of poly(acrylic acid) and poly(allylamine hydrochloride) as a protecting layer-by-layer coating for the upconverting NaYF4:Yb3+,Er3+ nanoparticles. The formation and crosslinking of the bilayer coating was confirmed with Fourier transform infrared spectroscopy, thermal analysis and zeta potential. The release of internal fluoride ions from the nanoparticle structure and subsequent particle disintegration was decelerated especially by crosslinking the bilayer coating on the surface. In addition, we studied the effect of the coating on the upconversion luminescence properties and learned that with additional fluoride ions present during the layer-by-layer assembly the most intense enhancement in the luminescent intensity is obtained. This is due both to not allowing the disintegration of the particles during the surface modification process as well as preventing the water molecules accessing the surface by crosslinking the bilayer coating.

Polydopamine Nanoparticles Prepared Using Redox-Active Transition Metals.

Autoxidation of dopamine to polydopamine by dissolved oxygen is a slow process that requires highly alkaline conditions. Polydopamine can be formed rapidly also in mildly acidic and neutral solutions by using redox-active transition-metal ions. We present a comparative study of polydopamine nanoparticles formed by autoxidation and aerobic or anaerobic oxidation in the presence of Ce(IV), Fe(III), Cu(II), and Mn(VII). The UV-vis spectra of the purified nanoparticles are similar, and dopaminechrome is an early intermediate species. At low pH, Cu(II) requires the presence of oxygen and chloride ions to produce polydopamine at a reasonable rate. The changes in dispersibility and surface charge take place at around pH 4, which indicates the presence of ionizable groups, especially carboxylic acids, on their surface. X-ray photoelectron spectroscopy shows the presence of three different classes of carbons, and the carbonyl/carboxylate carbons amount to 5-15 atom %. The N 1s spectra show the presence of protonated free amino groups, suggesting that these groups may interact with the π-electrons of the intact aromatic dihydroxyindole moieties, especially in the metal-induced samples. The autoxidized and Mn(VII)-induced samples do not contain metals, but the metal content is 1-2 atom % in samples prepared with Ce(IV) or Cu(II), and ca. 20 atom % in polydopamine prepared in the presence of Fe(III). These differences in the metal content can be explained by the oxidation and complexation properties of the metals using the general model developed. In addition, the nitrogen content is lower in the metal-induced samples. All of the metal oxidants studied can be used to rapidly prepare polydopamine at room temperature, but the possible influence of the metal content and nitrogen loss should be taken into account.

Effects of pH and Oxidants on the First Steps of Polydopamine Formation: A Thermodynamic Approach.

We present a general thermodynamic top-down analysis of the effects of oxidants and pH on dopamine oxidation and cyclization, supplemented with UV-vis and electrochemical studies. The model is applicable to other catecholamines and various experimental conditions. The results show that the decisive physicochemical parameters in autoxidation are the p K values of the semiquinone and the amino group in the oxidized quinone. Addition of Ce(IV) or Fe(III) enhances dopamine oxidation in acidic media in aerobic and anaerobic conditions by the direct oxidation of dopamine and, in the presence of oxygen, also by the autoxidation of the formed semiquinone. At pH 4.5, the enhancement of the one-electron oxidation of dopamine explains the overall reaction enhancement, but at a lower pH, cyclization becomes rate-determining. Oxidation by Cu(II) at reasonable rates requires the presence of oxygen or chloride ions.

Modeling the growth processes of polyelectrolyte multilayers using a quartz crystal resonator.

The layer-by-layer buildup of chitosan/hyaluronan (CH/HA) and poly(l-lysine)/hyaluronan (PLL/HA) multilayers was followed on a quartz crystal resonator (QCR) in different ionic strengths and at different temperatures. These polyelectrolytes were chosen to demonstrate the method whereby useful information is retrieved from acoustically thick polymer layers during their buildup. Surface acoustic impedance recorded in these measurements gives a single or double spiral when plotted in the complex plane. The shape of this spiral depends on the viscoelasticity of the layer material and regularity of the growth process. The polymer layer is assumed to consist of one or two zones. A mathematical model was devised to represent the separation of the layer to two zones with different viscoelastic properties. Viscoelastic quantities of the layer material and the mode and parameters of the growth process were acquired by fitting a spiral to the experimental data. In all the cases the growth process was mainly exponential as a function of deposition cycles, the growth exponent being between 0.250 and 0.275.

Surface modification of upconverting nanoparticles by layer-by-layer assembled polyelectrolytes and metal ions.

Modificating and protecting the upconversion luminescence nanoparticles is important for their potential in various applications. In this work we demonstrate successful coating of the nanoparticles by a simple layer-by-layer method using negatively charged polyelectrolytes and neodymium ions. The layer fabrication conditions such as number of the bilayers, solution concentrations and selected polyelectrolytes were studied to find the most suitable conditions for the process. The bilayers were characterized and the presence of the desired components was studied and confirmed by various methods. In addition, the upconversion luminescence of the bilayered nanoparticles was studied to see the effect of the surface modification on the overall intensity. It was observed that with selected deposition concentrations the bilayer successfully shielded the particle resulting in stronger upconversion luminescence. The layer-by-layer method offers multiple possibilities to control the bilayer growth even further and thus gives promises that the use of upconverting nanoparticles in applications could become even easier with less modification steps in the future.

Layer-by-layer assembled oxidative films as general platform for electrodeless formation of conducting polymers.

Fabrication of precisely tailored layers of conductive polymers in thin film assemblies is an attractive extension of the layer-by-layer technique. This approach provides tools for fabricating thin films with customized optical and electrical properties. In this paper, we study inorganic layer-by-layer assembled films prepared using polyphosphate and cerium(IV). It is shown that these multilayers can oxidize certain monomers from the adjacent aqueous solution to produce conducting polymer layers. We studied the thermodynamic factors that allow the aforementioned autopolymerization. A five bilayer polyphosphate/cerium(IV) film was shown to possess high oxidative power in acidic solutions. It was found that the polymerization of pyrrole, aniline and 3,4-ethylenedioxythiophene in contact with the redox active multilayer is thermodynamically favored. The rate of polymer formation and the thickness of the conducting film could be controlled by the concentration of the monomer in solution and the number of cerium/polyphosphate bilayers in the oxidative film. The oxidative polymerization of pyrrole was unambiguously recognized on UV-vis spectra with characteristic reduction and oxidation bands. The film formation was not restricted by charge diffusion and the reaction formally followed first-order kinetics. The results suggest that the reaction takes place effectively within the whole pre-existing polypyrrole film and it continues until all oxidant in the film was used. The spectral changes that are characteristic for conducting polypyrrole are shown on spectroelectrochemical analysis of the films indicating that cationic (polaron) and dicationic (bipolaron) species are involved in the redox processes of the film. The functional polymer films formed are found to be electroactive and conducting. Therefore, they fully resemble of conducting polymer films prepared using traditional electropolymerization.

Selection and characterization of peptides binding to diamond-like carbon.

Phage display was used to find peptides specific for amorphous diamond-like carbon (DLC). A set of putative binders was analyzed in detail and one sequence was found that functioned both as a peptide fused to the pIII protein in M13 phage and as a peptide fused to the enzyme alkaline phosphatase (AP). The dissociation constant of the peptide-AP fusion on DLC was 63nM and the maximum binding capacity was 6.8pmol/cm(2). Multiple ways of analysis, including phage titer, enzyme-linked immunosorbent assay, and ellipsometry were used to analyze binding and to exclude possible false positive results. DLC binding peptides can be useful for self-assembling coatings for modifying DLC in specific ways.

Method for measuring the losses and loading of a quartz crystal microbalance.

A novel, experimentally simple, and highly sensitive method for measuring the loading of a quartz crystal resonator was developed. The method is based on the use of double-sideband suppressed-carrier modulated high-frequency signal, which is swept through the resonance range of the resonator. Induced current in the resonator is passed through a capacitor, and the voltage over the capacitor is demodulated on an analog multiplier. The phase and amplitude information is carried to the frequency-doubled modulation signal and measured on a conventional low-frequency two-phase lock-in amplifier. A complex dimensionless loading parameter is obtained from the experimental data by nonlinear model fitting. The real and complex parts of this loading parameter have a simple relationship with other parameters commonly used for characterizing the resonator loading. The performance of the method was demonstrated by measuring a series of different glycerol-water mixtures ranging from 0 up to 100% glycerol. The results were close to the shear acoustic impedance of these mixtures measured and calculated from their viscosities and densities.

Effect of temperature on the buildup of polyelectrolyte multilayers.

The effect of temperature on the buildup of polyelectrolyte multilayers consisting of poly(styrenesulfonate) (PSS), poly(diallyldimethylammonium) (PDADMA), and poly(allylamine) (PAH) was studied by using a quartz crystal microbalance. The increase of temperature in the deposition process was shown to have a considerable effect on the rate of the layer-by-layer buildup. The effect of temperature on the PDADMA/PSS deposition was found to be stronger than on the PAH/PSS deposition. The increasing temperature was found to extend the exponential buildup regime in all of the studied systems. A buildup model was created to simulate the buildup and to explain the effect of temperature. The model is based on the assumption that each deposition step leads to a quasi-equilibrium between the concentration of the polymer repeating unit in solution and the composition of the layer. According to the model, the layer-by-layer buildup is inherently exponential, becoming linear whenever diffusion is not fast enough to carry the polymer within the entire thickness of the film. This buildup model is discussed jointly with the earlier published three-zone model of the polyelectrolyte multilayers. The rate of the buildup is characterized by growth exponent beta. The temperature dependence of the growth exponent is discussed in connection with the thermodynamic parameters of the deposition.

Large apparent interfacial slippage at polyelectrolyte-perfluorocarbon interfaces on a quartz crystal resonator.

The apparent negative areal mass densities obtained for a polyelectrolyte multilayer on a quartz crystal resonator in contact with four different perfluorocarbon liquids are explained by the interfacial slippage between the multilayer and the liquids. It is shown that the zone of interfacial slipping can be conveniently treated as a separate layer with distinct physical parameters. Three models of slippage were taken into a closer study. In the first model, the so-called de Gennes model, a very thin gas-filled cavity is formed between the moving phase and the stationary phase. The second model is based on the slipping layer consisting of water. In the third model, the so-called "true slipping" model, it is assumed that the particle velocity has a discontinuity at the interface. In each case, the slipping admittances and slippage lengths as well as the corrected areal mass densities were calculated from the experimental data. Although no unambiguous experimental evidence was found to favor strongly any of these three models, the slightly smaller variation in the slipping admittance and the areal mass density seems to give more credibility to the de Gennes model.