Quality Evaluation of Zirconium Dioxide Frameworks Produced in Five Dental Laboratories from Different Countries.

PURPOSE: The aim of this study was to assess and compare quality as well as economic aspects of CAD/CAM high strength ceramic three-unit FDP frameworks ordered from dental laboratories located in emerging countries and Switzerland. MATERIAL AND METHODS: The master casts of six cases were sent to five dental laboratories located in Thailand (Bangkok), China (Peking and Shenzhen), Turkey (Izmir), and Switzerland (Bern). Each laboratory was using a different CAD/CAM system. The clinical fit of the frameworks was qualitatively assessed, and the thickness of the framework material, the connector height, the width, and the diameter were evaluated using a measuring sensor. The analysis of the internal fit of the frameworks was performed by means of a replica technique, whereas the inner and outer surfaces of the frameworks were evaluated for traces of postprocessing and damage to the intaglio surface with light and electronic microscopes. Groups (dental laboratories and cases) were compared for statistically significant differences using Mann-Whitney U-tests after Bonferroni correction. RESULTS: An acceptable clinical fit was found at 97.9% of the margins produced in laboratory E, 87.5% in B, 93.7% in C, 79.2% in A, and 62.5% in D. The mean framework thicknesses were not statistically significantly different for the premolar regions; however, for the molar area 4/8 of the evaluated sites were statistically significantly different. Circumference, surface, and width of the connectors produced in the different laboratories were statistically significantly different but not the height. There were great differences in the designs for the pontic and connector regions, and some of the frameworks would not be recommended for clinical use. Traces of heavy postprocessing were found in frameworks from some of the laboratories. The prices per framework ranged from US$177 to US$896. CONCLUSIONS: By ordering laboratory work in developing countries, a considerable price reduction was obtained compared to the price level in Switzerland. Despite the use of the standardized CAD/CAM chains of production in all laboratories, a large variability in the quality aspects, such as clinical marginal fit, connector and pontic design, as well as postprocessing traces was noted. Recommended sound handling of postprocessing was not applied in all laboratories. Dentists should be aware of the true and factitious advantages of CAD/CAM production chains and not lose control over the process.

A 3D printed TCP/HA structure as a new osteoconductive scaffold for vertical bone augmentation.

INTRODUCTION: OsteoFlux(®) (OF) is a 3D printed porous block of layered strands of tricalcium phosphate (TCP) and hydroxyapatite. Its porosity and interconnectivity are defined, and it can be readily shaped to conform the bone bed's morphology. We investigated the performance of OF as a scaffold to promote the vertical growth of cortical bone in a sheep calvarial model. MATERIALS AND METHODS: Six titanium hemispheres were filled with OF, Bio-Oss (particulate bovine bone, BO), or Ceros (particulate TCP, CO) and placed onto the calvaria of 12 adult sheep (6 hemispheres/sheep). Histomorphometric analyses were performed after 8 and 16 weeks. RESULTS: OF led to substantial vertical bone growth by 8 weeks and outperformed BO and CO by a factor 2 yielding OF 22% ± 2.1; BO 11.5% ± 1.9; and CO 12.9% ± 2.1 total new bone. 3 mm away from the bony bed, OF led to a fourfold increase in new bone relative to BO and CO (n = 8, P < 0.002). At 16 weeks, OF, BO, and CO behaved similarly and showed marked new bone synthesis. A moderate degradation was observed at 16 weeks for all bone substitutes. CONCLUSION: When compared to existing bone substitutes, OF enhances vertical bone growth during the first 2 months after implantation in a sheep calvarial model. The controlled porous structure translated in a high osteoconductivity and resulted in a bone mass 3 mm above the bony bed that was four times greater than that obtained with standard substitutes. These results are promising but must be confirmed in clinical tests.

Three- to nine-year survival estimates and fracture mechanisms of zirconia- and alumina-based restorations using standardized criteria to distinguish the severity of ceramic fractures.

OBJECTIVES: The aims of this study were set as follows: 1. To provide verifiable criteria to categorize the ceramic fractures into non-critical (i.e., amenable to polishing) or critical (i.e., in need of replacement) 2. To establish the corresponding survival rates for alumina and zirconia restorations 3. To establish the mechanism of fracture using fractography MATERIALS AND METHODS: Fifty-eight patients restored with 115 alumina-/zirconia-based crowns and 26 zirconia-based fixed dental prostheses (FDPs) were included. Ceramic fractures were classified into four types and further subclassified into "critical" or "non-critical." Kaplan-Meier survival estimates were calculated for "critical fractures only" and "all fractures." Intra-oral replicas were taken for fractographic analyses. RESULTS: Kaplan-Meier survival estimates for "critical fractures only" and "all fractures" were respectively: Alumina single crowns: 90.9 and 68.3 % after 9.5 years (mean 5.71 ± 2.6 years). Zirconia single crowns: 89.4 and 80.9 % after 6.3 years (mean 3.88 ± 1.2 years). Zirconia FDPs: 68.6 % (critical fractures) and 24.6 % (all fractures) after 7.2 and 4.6 years respectively (FDP mean observation time 3.02 ± 1.4 years). No core/framework fractures were detected. CONCLUSIONS: Survival estimates varied significantly depending on whether "all" fractures were considered as failures or only those deemed as "critical". For all restorations, fractographic analyses of failed veneering ceramics systematically demonstrated heavy occlusal wear at the failure origin. Therefore, the relief of local contact pressures on unsupported ceramic is recommended. Occlusal contacts on mesial or distal ridges should systematically be eliminated. CLINICAL RELEVANCE: A classification standard for ceramic fractures into four categories with subtypes "critical" and "non-critical" provides a differentiated view of the survival of ceramic restorations.

Resin-bonded restorations: a strategy for managing anterior tooth loss in adolescence.

In children or adolescents with anterior tooth loss, space closure with the patient's own teeth should be considered as the first choice to avoid lifelong restorative needs. Thorough diagnostics and treatment planning are required when autotransplantation or orthodontic space closure is considered. If these options are not indicated and a single tooth implant restoration is considered, implant placement should be postponed until adulthood, particularly in young women and in patients with hyperdivergent skeletal growth pattern. A ceramic resin-bonded fixed dental prosthesis with 1 retainer is an excellent treatment solution for the interim period; it may also serve as a long-term restoration, providing that sound enamel structure is present, sufficient framework dimensions have been provided, adhesive cementation techniques have been meticulously applied, and functional contacts of the cantilever pontic avoided. In contrast, a resin-bonded fixed dental prosthesis with a metal framework and retentive preparation is indicated if the palatal enamel structure is compromised, interocclusal clearance is limited, splinting (such as after orthodontic treatment) is required, or more than 1 tooth has to be replaced.

Strength-limiting damage and defects of dental CAD/CAM full-contour zirconia ceramics.

OBJECTIVE: This study aimed to compare the four-point flexural strength of CAM-milled and sintered (as-sintered, AS) specimens with those of high-polished (HP) specimens using chairside polishing systems to simulate clinical surface conditions. METHODS: Seven full-contour zirconia CAM/CAM blanks with various yttria contents (3, 4, 5 mol%) including three high-translucent groups (5Y) were selected to prepare flexural specimens. The bend bar specimens (2.0 × 4.0 × 25.0 mm3) were fabricated by using STL file and dental CAM machine with the respective zirconia blanks (98 mm ϕ and 10-14 mm in height). Twelve bar specimens were machined from one zirconia puck and a total of 24 specimens were prepared from each group. The pre-sintered bar specimens were sintered by using a dental zirconia furnace at 1530-1550 °C for 2 h according to the instructions. All sintered specimens were divided into two groups: as-sintered (AS) group and high-polished (HP) groups (n = 12). HP groups were subjected to polishing one surface of specimens using a three-step polishing system and finally finished with diamond polishing. After cleaning and drying, the flexural strength of all specimens was determined by a fully articulating four-point flexure fixture consisting of a 1/4-point test configuration with an inner/outer span of 10/20 mm. Statistical differences between AS and HP groups were conducted with Weibull analysis. The fractured surfaces of zirconia specimens were observed using a field emission SEM and EDS to detect failure origins. RESULTS: The mean AS flexural strength values were significantly lower than those of HP counterparts. However, Weibull moduli expressing the reliability of HP groups were generally decreased although not significantly in comparison to their AS. The fracture of the AS specimens mostly originated from extrinsic CAM-milling defects, while the HP specimens were fractured from intrinsic subsurface or volume defects including pores, large grain clusters, inclusions, and corner-located critical flaws. Two high-translucent (5Y) zirconia groups were not affected in their strength and reliability after polishing, whereas one 5Y zirconia significantly increased its strength but significantly lowered its reliability. SIGNIFICANCE: The extrinsic and intrinsic strength-limiting defects should be considered in evaluating the flexural strength and reliability of dental CAD/CAM zirconia ceramics for full-contour restorations. For the materials tested in this study, more optimized processing of blanks and milling protocols of pre-sintered zirconia blanks should be developed including post-sintering surface finishing to reduce the flaw population regulating strength and reliability which will affect the survivability of dental zirconia prostheses.

Recent advances in dental zirconia: 15 years of material and processing evolution.

OBJECTIVES: The objective was to discuss the research on zirconia published in the past 15 years to help the dental materials community understand the key properties of the types of zirconia and their clinical applications. METHODS: A literature search was performed in May/2023 using Web of Science Core Collection with the term "dental zirconia". The search returned 5102 articles, which were categorized into 31 groups according to the research topic. RESULTS: The current approach to improving the translucency of zirconia is to decrease the alumina content while increasing the yttria content. The resulting materials (4Y-, 5Y-, and above 5 mol% PSZs) may contain more than 50% of cubic phase, with a decrease in mechanical properties. The market trend for zirconia is the production of CAD/CAM disks containing more fracture resistant 3Y-TZP at the bottom layers and more translucent 5Y-PSZ at the top. Although flaws located between layers in multilayered blocks might represent a problem, newer generations of zirconia layered blocks appear to have solved this problem with novel powder compaction technology. Significant advancements in zirconia processing technologies have been made, but there is still plenty of room for improvement, especially in the fields of high-speed sintering and additive manufacturing. SIGNIFICANCE: The wide range of zirconia materials currently available in the market may cause confusion in materials selection. It is therefore imperative for dental clinicians and laboratory technicians to get the needed knowledge on zirconia material science, to follow manufacturers' instructions, and to optimize the design of the prosthetic restoration with a good understanding where to reinforce the structure with a tough and strong zirconia.

An In Vitro Evaluation of the Effects of Air-Polishing Powders on Sound and Demineralised Enamel.

AIM: To evaluate the effects of two air-polishing powders, during orthodontic treatment, on the surface roughness of sound and demineralised enamel. MATERIALS AND METHODS: Forty-two caries-free human molars were collected, and the enamel surfaces were flattened and polished. Teeth were assigned to two groups (n = 21 each), a sound- and a demineralised-enamel group (subjected to pH-cycling over 2 weeks to create artificially induced white spot-like lesions). Within each group, teeth were further assigned to three groups (n = 7 each), air polished with either sodium bicarbonate, erythritol, or a negative control (water). Each sample was treated for 5 and 150 s. The average surface roughness (Ra) for each sample was measured using white-light-sensor profilometry. RESULTS: On sound enamel, the Ra was roughly 0.17 ± 0.07 µm. After 150 s of air polishing, the Ra increased with erythritol (by 0.28 µm), and even more so with bicarbonate treatment (by 0.68 µm) (p < 0.01). On demineralised enamel, the Ra was roughly 0.79 ± 0.56 µm. The Ra increased after 5 s of air-polishing treatment similarly with erythritol and bicarbonate powders (by 1.03 µm and 1.04 µm, respectively) (p = 0.025), and even more after 150 s (by 2.48 µm and 2.49 µm, respectively) (p < 0.001). CONCLUSIONS: On white spot lesions, one should be aware that enamel surface roughness will increase with both erythritol and bicarbonate air-polishing powders, especially with longer exposure times.

Implementation of the "loaded implant" model in the rat using a miniaturized setup--description of the method and first results.

OBJECTIVE: To miniaturize the "loaded implant" model to permit its application to small rodents. In this model, two titanium implants are placed 8 mm apart with their heads protruding from the skin and are forced together by a dedicated actuator. To assess the effect of (i) the post-implantation healing period and the duration of stimulation and (ii) the intratissular strain level on the microtomographical bone parameters BV/TV, Tb.N., Tb.Th. and BIC. MATERIALS AND METHODS: Implants, 1 × 8 mm, were machined, inserted into the tibiae of rats and activated. A total of 123 animals were used. In series 1, the implants were left to heal for 2/4 weeks and then loaded to generate intratissular strains of 1125 ± 5% µÎµ for 4/8 weeks. Series 2 had their implants loaded to 750, 1500 and 2250 ± 5% µÎµ, respectively. RESULTS: Bone to implant contact increased upon loading. In series 1, no difference was observed regarding the duration of healing or the stimulation period. In series 2, at 750 µÎµ, the bone parameters did not differ from baseline. At 1500 µÎµ, all four parameters increased. At 2250 µÎµ, three of four parameters decreased relative to 1500 µÎµ. CONCLUSIONS: (i) The loaded implant model can be miniaturized to the millimeter range; (ii) in the present model, implant activation beyond 4 weeks did not affect the bone parameters; (iii) mechanical stimulation increased bone to implant contact by up to 20%; (iv) the results obtained are consistent with the concept of an anabolic effect from 750 to 1500 µÎµ and deleterious effects at strains in the 2250 µÎµ range; and (v) strains at 2250 µÎµ did not lead to implant dis-integration.

Identification of Type-H-like Blood Vessels in a Dynamic and Controlled Model of Osteogenesis in Rabbit Calvarium.

Angiogenesis and bone regeneration are closely interconnected processes. Whereas type-H blood vessels are abundantly found in the osteogenic zones during endochondral long bone development, their presence in flat bones' development involving intramembranous mechanisms remains unclear. Here, we hypothesized that type-H-like capillaries that highly express CD31 and Endomucin (EMCN), may be present at sites of intramembranous bone development and participate in the control of osteogenesis. A rabbit model of calvarial bone augmentation was used in which bone growth was controlled over time (2-4 weeks) using a particulate bone scaffold. The model allowed the visualization of the entire spectrum of stages throughout bone growth in the same sample, i.e., active ossification, osteogenic activity, and controlled inflammation. Using systematic mRNA hybridization, the formation of capillaries subpopulations (CD31-EMCN staining) over time was studied and correlated with the presence of osteogenic precursors (Osterix staining). Type-H-like capillaries strongly expressing CD31 and EMCN were identified and described. Their presence increased gradually from the regenerative zone up to the osteogenic zone, at 2 and 4 weeks. Type-H-like capillaries may thus represent the initial vascular support encountered in flat bones' development and which organize osteogenic niches.

Preferences of dental care providers in maintaining compromised teeth in relation to their professional status: implants instead of periodontally involved maxillary molars?

AIM: The purpose of this study was to evaluate the dentists' decision making in the maxillary molar region to find out how it is influenced by general practitioners' and specialists' characteristics as well as by the external evidence. MATERIAL AND METHODS: A questionnaire was developed containing clinical cases and statements to assess practitioners' opinions on the treatment of periodontally involved maxillary molars and implant therapy with sinus grafting. Data were analysed with respect to the dentists' age and specialty. RESULTS: Three hundred and forty questionnaires were evaluated (24% from universities, 76% from educational courses, overall response rate 35.1%). Forty six per cent of all participants indicated they had specialised, 52% placed dental implants, while 33% performed sinus grafting and 64% periodontal surgeries. Forty six per cent were against or were indecisive about having sinus grafting performed on themselves. The treatment proposals given for the clinical cases revealed a preference among older dentists and general practitioners for regenerative treatments even when these were not evidence based in through-and-through furcation involvements. Resective therapies were most often selected by periodontists. Prosthodontists tended to prefer more invasive treatment options with extractions and augmentations. More experienced general practitioners favoured conventional fixed dental prostheses in free-end situations or no treatment rather than the complicated augmentation procedures, which were preferred by younger dentists. CONCLUSIONS: Implant placement seems to be widely accepted by almost all subjects, who may either place implants themselves or refer patients. More information seems to be needed on the indications for regenerative therapies for furcation involved maxillary molars, and guidelines required for decision making in complex clinical situations.

Fractography of clinical failures of indirect resin composite endocrown and overlay restorations.

OBJECTIVES: Compare failure modes and fracture origins using fractography on recovered clinically fractured parts of indirect resin composite endocrowns and overlay restorations on endodontically treated teeth (ETT). METHODS: Four endocrowns (3 molars, 1 premolar) and one overlay (molar) adhesively luted on ETT were recovered after fracturing during function. The time in service ranged between 4 and 48 months. The composite materials were (i) CAD/CAM LAVA Ultimate (N = 1), (ii) Premise Indirect (N = 2), and (iii) Colombus (N = 2). Fractography was performed by means of digital microscopy and SEM. Occlusal surfaces were checked for signs of fatigue degradation and contact wear. Cuspal plane angles were measured from profiles obtained from 3D digital microscope images with respect to the horizontal plane of the occlusal central crown groove. RESULTS: All five cases showed a wedge-opening mode I fracture, splitting the crown and tooth in two parts through the crown's central groove. Classic brittle fracture features (arrest lines, twist and wake hackle) were easily identified on the fracture surfaces. Multiple origins were located along the central groove in conjunction with the presence of fatigue cracks. Contact wear surfaces showed pitting and cracking. Cuspal plane angles were around 30-35°, except a 50° palatal cusp slope for the Lava Ultimate overlay. SIGNIFICANCE: Fractography on clinical fractures of resin composites was enlightening. Occlusal surface fatigue degradation from cyclic loading, mode I fracture from applied mastication forces on cuspal planes, and stress concentration within the crown's central groove, indicate limitations of use of these materials for endocrowns in posterior teeth.

Pre-Treat Xenogenic Collagenous Blocks of Bone Substitutes with Saline Facilitate Their Manipulation and Guarantee High Bone Regeneration Rates, Qualitatively and Quantitatively.

Deproteinized bovine bone mineral particles embedded in collagen (DBBM-C) are widely used for bone regenerations with excellent, albeit sometimes variable clinical outcomes. Clinicians usually prepare DBBM-C by mixing with blood. Replacing blood by saline represents an alternative. We investigated if saline treatment could improve DBBM-C i. handling in vitro and ii. biological performances in a rabbit calvarial model. In vitro, DBBM-C blocks soaked in saline or blood were submitted to compression tests. In vivo, four poly ether ether ketone (PEEK)cylinders were placed on 16 rabbit skulls, filled with DBBM-C soaked in blood or saline for 2-4-8-12 weeks before histomorphometry. DBBM-C blocks were fully hydrated after 30 s in saline when 120 s in blood could not hydrate blocks core. Stiffness gradually decreased 2.5-fold after blood soaking whereas a six-fold decrease was measured after 30 s in saline. In vivo, saline treatment allowed 50% more bone regeneration during the first month when compared to blood soaking. This difference was then no longer visible. New bone morphology and maturity were equivalent in both conditions. DBBM-C saline-soaking facilitated its handling and accelerated bone regeneration of highly qualitative tissues when compared to blood treatment. Saline pretreatment thus may increase the clinical predictability of bone augmentation procedures.

A dual-ink 3D printing strategy to engineer pre-vascularized bone scaffolds in-vitro.

A functional vascular supply is a key component of any large-scale tissue, providing support for the metabolic needs of tissue-remodeling cells. Although well-studied strategies exist to fabricate biomimetic scaffolds for bone regeneration, success rates for regeneration in larger defects can be improved by engineering microvascular capillaries within the scaffolds to enhance oxygen and nutrient supply to the core of the engineered tissue as it grows. Even though the role of calcium and phosphate has been well understood to enhance osteogenesis, it remains unclear whether calcium and phosphate may have a detrimental effect on the vasculogenic and angiogenic potential of endothelial cells cultured on 3D printed bone scaffolds. In this study, we presented a novel dual-ink bioprinting method to create vasculature interwoven inside CaP bone constructs. In this method, strands of a CaP ink and a sacrificial template material was used to form scaffolds containing CaP fibers and microchannels seeded with vascular endothelial and mesenchymal stem cells (MSCs) within a photo-crosslinkable gelatin methacryloyl (GelMA) hydrogel material. Our results show similar morphology of growing vessels in the presence of CaP bioink, and no significant difference in endothelial cell sprouting was found. Furthermore, our initial results showed the differentiation of hMSCs into pericytes in the presence of CaP ink. These results indicate the feasibility of creating vascularized bone scaffolds, which can be used for enhancing vascular formation in the core of bone scaffolds.

Fractal analysis at varying locations of clinically failed zirconia dental implants.

OBJECTIVES: Previous studies have shown that the fracture toughness of ceramics can be determined from the fractal dimensions (D) of their fracture surfaces and that the surface should be leveled to obtain an accurate D measurement. This study was to determine the effects of leveling operations and distance from the failure origin on the D values. METHODS: Twelve clinically failed zirconia implants from four different manufacturers: Axis Biodental (n=7), Z-Systems (n=3), Straumann (n=1), and Swiss Dental Solutions (n=1) were obtained from one of the authors and thoroughly cleaned. Epoxy replicas were made of three locations along the crack path in the center region of each fracture surface (near origin (O), hackle (H), and near compression curl (CC)) using a light body polyvinyl siloxane impression material. Surfaces were scanned in ScanAsyst mode with a scan size of 5µm×5µm and a scan rate of 0.592Hz using the atomic force microscope. The surface scans were then leveled using 1st order flattening operation in the AFM analysis software. The height data before and after the operation were imported into a custom MathCAD script, and FRACTALS software was used to determine the D value by Minkowski Cover algorithm, which was shown previously to be the algorithm with the highest precision. A Wilcoxon signed-rank test, two-way repeated-measures ANOVA, and one-way repeated-measures ANOVA were performed as detailed below. RESULTS: The data were not normally distributed (S-W p≤0.05), so a non-parametric repeated measures test (Wilcoxon signed-rank test) was selected. The median D values before and after leveling were 2.161 and 2.174, respectively. There was a significant difference before and after leveling (p<0.001). The two-way repeated-measures ANOVA showed no significant difference among the D values for different implant brands (p=0.66) and scanning locations on the fracture surface (p=0.83). After eliminating the implant brand as a factor, the data passed normality and equal variance tests (S-W p=0.88, BF p=0.15). The mean D values and standard deviations from the three locations (O, H, CC) were 2.183±0.031, 2.179±0.024, and 2.175±0.018, respectively. One-way repeated measures ANOVA showed no significant effect of scanning location (p=0.74). SIGNIFICANCE: The leveling operation successfully removed the tilt without decreasing surface tortuosity, as it increased the D values significantly. The fractal dimension was the same at the three locations on the fracture surfaces. This means that hackle and compression curl regions can be used to determine fracture toughness when the failure origin has been lost.

The effect of water storage, elapsed time and contaminants on the bond strength and interfacial polymerization of a nanohybrid composite.

PURPOSE: To systematically characterize the effect of time lapse, water storage, and selected contaminants on the bond strength of a nanofilled dental composite. MATERIALS AND METHODS: Half-dumbbell-shaped samples were fabricated out of light-polymerizing composite resin. To function as substrates they were aged for 30 days in water. Prior to bonding, the substrates' surfaces were subjected to the following treatments: 1) Removing a 0.2- to 0.4-mm layer using a fluted carbide bur; 2) grit blasting with 50 microm alumina particles; 3) etching with phosphoric acid gel; 4) grit blasting followed by etching; 5) blasting with tribochemical particles followed by silane application; 6) sanding with 400-grit paper, air aging of the adherent half-sample before bonding; 7) surface contamination with saliva; 8) surface contamination with blood. In each group (n = 30), freshly polymerized (except in group 6) adherent half-samples were bonded to the substrate half-samples by a layer of unfilled adhesive resin. Fifteen full dumbbell-shaped specimens were subjected to tensile testing after 1 h and 15 after 7 days water storage. In a positive control group, freshly cured half-samples were bonded shortly after fabrication. The tensile strength was analyzed using Weibull statistics and presented in terms of the material's characteristic strength and shape parameter. Fractographs of the two weakest and strongest samples of each group were produced. The surfaces were searched to locate hackle, wake hackle and the origin of the fracture. RESULTS: Surface roughness and time lapse increased the bond strength of the repaired specimens. All groups in which surface roughness was produced before bonding increased in repair strength. Post-bonding aging improved strength. Fractographs yielded interpretable data whenever larger surfaces of single phase bonding resin were present. CONCLUSION: 1) Roughening and etching an aged composite's surface prior to applying a coat of unfilled resin and the filled material increases repair bond strength by up to 100%. 2) The repair bond strength of a roughened aged composite is 25% to 30% inferior to the tensile strength of solid specimens. 3) After 7 days' storage in water, no detrimental effect could be seen from saliva or blood contamination if the surfaces were properly rinsed.

Translational research on clinically failed zirconia implants.

OBJECTIVES: To provide fractographic analysis of clinically fractured zirconia implants recovered with their cemented crown. To calculate bending moments, corresponding stress and crack onset location on the implant's fracture surface using a mathematical model integrating spatial coordinates of the crown-implant part and occlusal loading obtained from 2D and 3D images. METHODS: 15 fractured zirconia implants parts (11 posterior and 4 anterior) with their all- ceramic crowns still cemented on it were recovered. The implants were first generations from four manufacturers (AXIS Biodental, Z-Systems, Straumann, Swiss Dental Solutions). The time-to-failure varied between 2weeks and 9years. Fractography was performed identifying the failure origin and characteristic surface crack features. From 2D and 3D digital images of the crown-implant part, spatial coordinates anchoring the crown's occlusal contacts with the implant's central axis and reference plane were integrated in a mathematical model spreadsheet. Loads of 500 N in total were selectively distributed over identified occlusal contacts from wear patterns. The resultant bending and torsion moments, corresponding shear, tensile, maximum principal stress and von Mises stress were calculated. The fracture crack onset location on the implant's fracture surface was given by an angular position with respect to an occlusal reference and compared with the location of the fracture origin identified from fractographic analysis. RESULTS: Implants fractured from the periphery of the smaller inner diameter between two threads at the bone-entrance level except for one implant which failed half-way within the bone. The porous coating (AXIS Biodental) and the large grit alumina sandblasting (Z-System) created surface defects directly related to the fracture origin. The model spreadsheet showed how occlusal loading with respect to the implant's central axis affects bending moments and crack onset. Dominant loads distributed on contacts with important wear pattern provided a calculated crack onset location in good agreement with the fractographic findings of the fracture origin. SIGNIFICANCE: Recovered broken zirconia implant parts with their restorative crowns can provide not only information regarding the failure origin using fractography but also knowledge regarding occlusal crown loading with respect to the implant's axis. The mathematical model was helpful in showing how occlusal loading affects the location of the fracture initiation site on clinical zirconia implant fracture cases.

Calvarial Model of Bone Augmentation in Rabbit for Assessment of Bone Growth and Neovascularization in Bone Substitution Materials.

The basic principle of the rabbit calvarial model is to grow new bone tissue vertically on top of the cortical part of the skull. This model allows assessment of bone substitution materials for oral and craniofacial bone regeneration in terms of bone growth and neovascularization support. Once animals are anesthetized and ventilated (endotracheal intubation), four cylinders made of polyether ether ketone (PEEK) are screwed onto the skull, on both sides of the median and coronal sutures. Five intramedullary holes are drilled within the bone area delimited by each cylinder, allowing influx of bone marrow cells. The material samples are placed into the cylinders which are then closed. Finally, the surgical site is sutured, and animals are awaken. Bone growth may be assessed on live animals by using microtomography. Once animals are euthanized, bone growth and neovascularization may be evaluated by using microtomography, immune-histology and immunofluorescence. As the evaluation of a material requires maximum standardization and calibration, the calvarial model appears ideal. Access is very easy, calibration and standardization are facilitated by the use of defined cylinders and four samples may be assessed simultaneously. Furthermore, live tomography may be used and ultimately a large decrease in animals to be euthanized may be anticipated.

Bone reactions to controlled loading of endosseous implants: a pilot study.

OBJECTIVES: To validate an experimental setup designed to apply load onto bone tissue using osseointegrated implants in a rabbit model. Specifically, (1) to design an apparatus capable of generating controlled forces, (2) to assess implant placement, maintenance and loading and (3) to evaluate outcome variables using three radiological methods. MATERIAL AND METHODS: New Zealand White rabbits were used. Two dental implants were inserted 15-18 mm apart in the animals' tibiae. After 3 months of healing, the implants were loaded normal to their long axes using a pneumatically activated device. A 15 min load regimen at 1 Hz was applied 5 days per week. Every week the applied load was increased by 5 N up to week 8 and by 10 N up to 100 N by week 14. Groups of animals (n=3) were sacrificed at load levels 25, 50 and 100 N. One unloaded controlateral implant in each group provided the baseline data. The rabbits were computer tomography (CT) scanned and radiographed using conventional frames every 4-5 weeks. After sacrifice, a volume of interest (VOI) located in the inter-implant zones and a VOI set as a ring surrounding the distal implant were analyzed using micro computer tomography (microCT). RESULTS: A variety of osseous responses was observed, ranging from minor alterations to significant increases in porosity and lamelling of the cortical layer. microCT data of the inter-implant VOI demonstrated an initial increase in total volume (upto 50 N) followed by stabilization. Concomitantly, bone volumetric density first decreased and then augmented until the end of the experiment. This phenomenon was not observed in the peri-implant VOI, for which volumetric density augmented from the beginning to the end of the experiment. CONCLUSIONS: 1. In future trials the loading devices must be constructed so as to sustain heavy cyclic loads over prolonged periods. 2. When properly handled, rabbits are cooperative animals in this application. In a third of the sites, signs of inflammation were observed. 3. In the inter-implant VOI, the cortical bone tended to react in two phases: first, as an increase in porosity and lamelling and second, as an augmentation of bone volumetric density. The peri-implant VOI adapted only by augmenting volumetric density.

Fractographic failure analysis of a Procera AllCeram crown using stereo and scanning electron microscopy.

OBJECTIVES: Presentation of a methodological approach using stereo and scanning electron microscope examination for the failure analysis of an alumina all-ceramic premolar crown (Procera AllCeram). METHODS: The recovered part of a fractured Procera alumina crown was examined utilizing first a stereomicroscope and second a scanning electron microscope (SEM). The stereomicroscope analysis was performed at low magnifications with oblique lighting in order to enhance spatial relationships and gross detection of crack features. A preliminary fracture surface map of the stereo observations was drawn and used as a guide for the SEM analysis that followed. Specific sites of interest identified under the stereo microscope were analyzed using the SEM at high magnifications searching for small fracture features such as wake hackle and twist hackle within the veneering ceramic in order to confirm the direction of crack propagation. RESULTS: At low magnifications and oblique illumination, the stereomicroscope analysis provided an excellent overview of the fractured topography, showing sites of major interest such as a primary edge chip at a margin, a compression curl indicating the end of the fracture event as well as larger hackle lines distributed over the cracked surface. The greater magnifications with the SEM analysis of the sites of interest showed the presence of wake and twist hackle, indicators of the crack propagation direction. A general map of the fracture events could be reconstructed starting with a primary veneer edge chip at the mesial margin. Hackle and wake hackle of the crack front emanating from this margin arose from hoop stresses and propagated through the full crown thickness towards the distal end of the restoration where the compression curl was located. Additional occlusal surface damage in the form of veneer chipping containing arrest lines and twist hackle running in the opposite direction as the main crack path were observed, but occurred as a secondary event without penetrating the alumina core material. SIGNIFICANCE: Stereo and scanning electron microscopy are complementary analysis techniques useful for the mapping and interpretation of the fracture surface. This case examination is intended to guide the clinical researcher in using qualitative (descriptive) fractography as a tool for understanding the failure process in brittle restorative materials, as well as for assessing possible design inadequacies.

Microstructural characterization and fracture behavior of a microhybrid and a nanofill composite.

OBJECTIVES: To characterize the microstructure and composition of two different composites, and to determine their influence on the physical properties and fracture behavior. METHODS: The microstructure and composition of a microhybrid (Filtek Z250-Z2) and a nanofill (Filtek Supreme-SU) composite were analyzed using scanning electron microscopy (SEM) and electron dispersive spectroscopy (EDS). Filler wt% was determined by thermogravimetric analysis. Hardness (H) and degree of conversion (DC) were evaluated at top and bottom surfaces of 2-mm thick specimens, and the dynamic elastic modulus (E) was determined with ultrasonic waves. Bar specimens (n=30) were subjected to flexure loading and flexural strength (sigmaf) was calculated (MPa). Fractographic analysis (FA) was performed to determine the fracture origin (c) for calculation of fracture toughness (KIc), and these results were compared to those from the single edge notch beam (SENB) method. Results were statistically analyzed using two-way ANOVA, Student's t-test and Weibull analysis (alpha=0.05). RESULTS: Z2 had higher filler wt%, H, E and DC at 2-mm depth as compared with SU. The fracture behavior (sigmaf and KIc) and the structural reliability (m) of the composites were similar. Results of KIc tested by SENB or calculated from fracture surfaces from flexure testing were similar. SIGNIFICANCE: The microstructural organization of the composites determines their physical properties, in spite of the similar filler content. In contrast, the microstructure did not influence the fracture behavior and the structural reliability of these highly filled composites. FA was shown to be a reliable method for determining the KIc of composites.