Poly(Allylamine Hydrochloride) and ZnO Nanohybrid Coating for the Development of Hydrophobic, Antibacterial, and Biocompatible Textiles.

In healthcare facilities, infections caused by Staphylococcus aureus (S. aureus) from textile materials are a cause for concern, and nanomaterials are one of the solutions; however, their impact on safety and biocompatibility with the human body must not be neglected. This study aimed to develop a novel multilayer coating with poly(allylamine hydrochloride) (PAH) and immobilized ZnO nanoparticles (ZnO NPs) to make efficient antibacterial and biocompatible cotton, polyester, and nylon textiles. For this purpose, the coated textiles were characterized with profilometry, contact angles, and electrokinetic analyzer measurements. The ZnO NPs on the textiles were analyzed by scanning electron microscopy and inductively coupled plasma mass spectrometry. The antibacterial tests were conducted with S. aureus and biocompatibility with immortalized human keratinocyte cells. The results demonstrated successful PAH/ZnO coating formation on the textiles, demonstrating weak hydrophobic properties. Furthermore, PAH multilayers caused complete ZnO NP immobilization on the coated textiles. All coated textiles showed strong growth inhibition (2-3-log reduction) in planktonic and adhered S. aureus cells. The bacterial viability was reduced by more than 99%. Cotton, due to its better ZnO NP adherence, demonstrated a slightly higher antibacterial performance than polyester and nylon. The coating procedure enables the binding of ZnO NPs in an amount (<30 µg cm-2) that, after complete dissolution, is significantly below the concentration causing cytotoxicity (10 µg mL-1).

Microplastics encapsulation in aragonite: efficiency, detection and insight into potential environmental impacts.

Plastic pollution in aquatic ecosystems has become a significant problem especially microplastics which can encapsulate into the skeletons of organisms that produce calcium carbonates, such as foraminifera, molluscs and corals. The encapsulation of microplastics into precipitated aragonite, which in nature builds the coral skeleton, has not yet been studied. It is also not known how the dissolved organic matter, to which microplastics are constantly exposed in aquatic ecosystems, affects the encapsulation of microplastics into aragonite and how such microplastics affect the mechanical properties of aragonite. We performed aragonite precipitation experiments in artificial seawater in the presence of polystyrene (PS) and polyethylene (PE) microspheres, untreated and treated with humic acid (HA). The results showed that the efficiency of encapsulating PE and PE-HA microspheres in aragonite was higher than that for PS and PS-HA microspheres. The mechanical properties of resulting aragonite changed after the encapsulation of microplastic particles. A decrease in the hardness and indentation modulus of the aragonite samples was observed, and the most substantial effect occurred in the case of PE-HA microspheres encapsulation. These findings raise concerns about possible changes in the mechanical properties of the exoskeleton and endoskeleton of calcifying marine organisms such as corals and molluscs due to the incorporation of pristine microplastics and microplastics exposed to dissolved organic matter.

Antibacterial evaluation of different prosthetic liner textiles coated by CuO nanoparticles.

Prosthetic liners are mainly used as an interface between residual limbs and prosthetic sockets to minimize physical and biological damage to soft tissue. However, the closed and moist conditions within liners and the amputee's skin provide a suitable environment for bacterial growth to cause infections. This study aimed to coat a comprehensive variant material with copper oxide nanoparticles (CuO NPs) and compare their surface analysis and antibacterial properties. These materials were covered with CuO NPs solution at a concentration of 70 µg mL-1 to achieve this purpose. After drying, their surface characteristics were analyzed by measuring zeta potential, contact angle, surface roughness, and fiber arrangement. Cu-released concentration from the coatings into the acetate buffer solution by inductively coupled plasma mass spectrometry indicated that lycra and nylon quickly released Cu ions to concentrations up to ∼0.2 µg mL-1 after 24 h, causing low metabolic activity of human bone-marrow mesenchymal stem cells (bMSC) in the indirect assay. Antibacterial activity of the coated specimens was evaluated by infecting their surfaces with the Gram-positive bacteria Staphylococcus epidermidis, reporting a significant ∼40 % reduction of metabolic activity for x-dry after 24 h; in addition, the number of viable bacterial colonies adhered to the surface of this material was reduced by ∼23 times in comparison with non-treated x-dry that were visually confirmed by scanning electron microscope. In conclusion, CuO NPs x-dry shows optimistic results to pursue further experiments due to its slow speed of Cu release and prolonged antibacterial activity, as well as its compatibility with human cells.

Investigation of the Influence of Wound-Treatment-Relevant Buffer Systems on the Colloidal and Optical Properties of Gold Nanoparticles.

Biocompatible gold nanoparticles (AuNPs) are used in wound healing due to their radical scavenging activity. They shorten wound healing time by, for example, improving re-epithelialization and promoting the formation of new connective tissue. Another approach that promotes wound healing through cell proliferation while inhibiting bacterial growth is an acidic microenvironment, which can be achieved with acid-forming buffers. Accordingly, a combination of these two approaches appears promising and is the focus of the present study. Here, 18 nm and 56 nm gold NP (Au) were prepared with Turkevich reduction synthesis using design-of-experiments methodology, and the influence of pH and ionic strength on their behaviour was investigated. The citrate buffer had a pronounced effect on the stability of AuNPs due to the more complex intermolecular interactions, which was also confirmed by the changes in optical properties. In contrast, AuNPs dispersed in lactate and phosphate buffer were stable at therapeutically relevant ionic strength, regardless of their size. Simulation of the local pH distribution near the particle surface also showed a steep pH gradient for particles smaller than 100 nm. This suggests that the healing potential is further enhanced by a more acidic environment at the particle surface, making this strategy a promising approach.

Cation Adsorption in TiO2 Nanotubes: Implication for Water Decontamination.

TiO2 nanotubes constitute very promising nanomaterials for water decontamination by the removal of cations. We combined a range of experimental techniques from structural analyses to measurements of the properties of aqueous suspensions of nanotubes, with (i) continuous solvent modeling and (ii) quantum DFT-based simulations to assess the adsorption of Cs+ on TiO2 nanotubes and to predict the separation of metal ions. The methodology is set to be operable under realistic conditions, which, in this case, include the presence of CO2 that needs to be treated as a substantial contaminant, both in experiments and in models. The mesoscopic model, based on the Poisson-Boltzmann equation and surface adsorption equilibrium, predicts that H+ ions are the charge-determining species, while Cs+ ions are in the diffuse layer of the outer surface with a significant contribution only at high concentrations and high pH. The effect of the size of nanotubes in terms of the polydispersity and the distribution of the inner and outer radii is shown to be a third-order effect that is very small when the nanotube layer is not very thick (ranging from 1 to 2 nm). Besides, DFT-based molecular dynamics simulations demonstrate that, for protonation, the one-site and successive association assumption is correct, while, for Cs+ adsorption, the size of the cation is important and the adsorption sites should be carefully defined.

Nanoparticles: From synthesis to applications and beyond.

In modern-day research, nanoparticles (size < 100nm) are an indispensable tool for various applications, especially in the field of biomedicine. Although enormous efforts have been made to understand the properties and specificities of nanoparticles, many questions are still not answered and the new ones arise. In this review we summarize current trends in the nanoparticle synthesis and characterization and interpret the stability of nanoparticles in various media from aqueous solutions to biological milieu important for the in vitro and in vivo studies. To get more detailed insight into nanoparticle charging properties and interactions of nanoparticles with interfaces the theoretical models are presented. Finally, the overview of nanoparticle applications is given and the future prospects are discussed.

Selenite as a Lipid Inductor in Marine Microalga Dunaliella tertiolecta: Comparison of One-Stage and Two-Stage Cultivation Strategies.

Microalgae have emerged as one of the most promising alternative sources of biofuels due to their high lipid accumulation ability. High lipid content is of pivotal importance for biodiesel production. In order to obtain high lipid content, modifications of culture conditions and development of an efficient lipid induction method are called for. In the present study, the possibility of using selenium in a form of sodium selenite as a lipid inductor in marine microalga Dunaliella tertiolecta was investigated during one- and two-stage cultivation modes. The effects of selenite on algal growth, pigment content, oxidative stress, and neutral lipid content were determined during both cultivation modes. The results revealed that the two-stage cultivation on 10.00-40.00 mg L-1 of selenite resulted in up to twofold higher algal cell density compared to the one-stage cultivation. Selenite concentrations from 2.50 to 20.00 mg L-1 increased lipid peroxidation during both cultivation modes, emphasizing the selenite-induced oxidative stress accompanied by the increased lipid accumulation in microalgae cells. During one- and two-stage cultivation on 20.00 mg L-1 of selenite, lipid content increased 2.39- and 5.73-fold at days 9 and 14 of cultivation, respectively. Moreover, the highest obtained neutral lipid content during the two-stage cultivation was 5.40-fold higher than lipid content obtained during the one-stage cultivation. Collectively, these results suggest that the two-stage cultivation strategy, initiated with optimal culture conditions for biomass production and followed by the addition of selenite as a stress inductor, can be successfully deployed to enhance the lipid content in D. tertiolecta.

Thiolated Chitosan Conjugated Liposomes for Oral Delivery of Selenium Nanoparticles.

This study aimed to design a hybrid oral liposomal delivery system for selenium nanoparticles (Lip-SeNPs) to improve the bioavailability of selenium. Thiolated chitosan, a multifunctional polymer with mucoadhesive properties, was used for surface functionalization of Lip-SeNPs. Selenium nanoparticle (SeNP)-loaded liposomes were manufactured by a single step microfluidics-assisted chemical reduction and assembling process. Subsequently, chitosan-N-acetylcysteine was covalently conjugated to the preformed Lip-SeNPs. The Lip-SeNPs were characterized in terms of composition, morphology, size, zeta potential, lipid organization, loading efficiency and radical scavenging activity. A co-culture system (Caco-2:HT29-MTX) that integrates mucus secreting and enterocyte-like cell types was used as a model of the human intestinal epithelium to determine adsorption, mucus penetration, release and transport properties of Lip-SeNPs in vitro. Thiolated Lip-SeNPs were positively charged with an average size of about 250 nm. Thiolated Lip-SeNPs tightly adhered to the mucus layer without penetrating the enterocytes. This finding was consistent with ex vivo adsorption studies using freshly excised porcine small intestinal tissues. Due to the improved mucoadhesion and retention in a simulated microenvironment of the small intestine, thiolated Lip-SeNPs might be a promising tool for oral selenium delivery.

Preparation and detailed characterization of the thiomer chitosan-cysteine as a suitable mucoadhesive excipient for nasal powders.

The therapeutic application of nasal powders requires the development of novel mucoadhesive excipients. Thiolated polymers exhibit significant potential for this purpose based on their increased mucoadhesion attributable to the formation of disulfide bonds between the polymer and mucus surface. A chitosan-cysteine (chit-cyst) conjugate was synthesized using 1-(3-Dimethylaminopropyl)-3-ethylcarbodiimide hydrochloride and N-hydroxysuccinimide in aqueous solution. The synthetic yield and synthesis conditions were optimized, and the efficiency of the reaction was evaluated. Rheological measurements revealed that the polymer derivative exhibited increased mucoadhesive properties in comparison to chitosan powder. To characterize the polymer, a novel purity investigation method was developed and verified to investigate the residual l-cysteine content. The results revealed that l-cysteine was not detectable in the resultant polymer matrix. Based on the cytotoxicity studies, chit-cyst was found to be safe for nasal application. Thereafter, nasal powder formulations were prepared using the polymer and the antiparkinsonian drug levodopa methyl ester hydrochloride by freeze-drying to investigate their nasal applicability. Based on the in vitro studies, these powders might be suitable for reducing the off periods of Parkinson's disease because of their expected higher in vivo mucoadhesion.

Precipitation at Room Temperature as a Fast and Versatile Method for Calcium Phosphate/TiO2 Nanocomposites Synthesis.

The constantly growing need for advanced bone regeneration materials has motivated the development of calcium phosphates (CaPs) composites with a different metal or metal-oxide nanomaterials and their economical and environmentally friendly production. Here, two procedures for the synthesis of CaPs composites with TiO2 nanoplates (TiNPl) and nanowires (TiNWs) were tested, with the immersion of TiO2 nanomaterials (TiNMs) in corrected simulated body fluid (c-SBF) and precipitation of CaP in the presence of TiNMs. The materials obtained were analyzed by powder X-ray diffraction, spectroscopic and microscopic techniques, Brunauer-Emmett-Teller surface area analysis, thermogravimetric analysis, dynamic and electrophoretic light scattering, and their hemocompatibility and ability to induce reactive oxygen species were evaluated. After 28 days of immersion in c-SBF, no significant CaP coating was formed on TiNMs. However, the composites with calcium-deficient apatite (CaDHA) were obtained after one hour in the spontaneous precipitation system. In the absence of TiNMs, CaDHA was also formed, indicating that control of the CaP phase formed can be accomplished by fine-tuning conditions in the precipitation system. Although the morphology and size of crystalline domains of CaDHA obtained on the different nanomaterials differed, no significant difference was detected in their local structure. Composites showed low reactive oxygen species (ROS) production and did not induce hemolysis. The results obtained indicate that precipitation is a suitable and fast method for the preparation of CaPs/TiNMs nanocomposites which shows great potential for biomedical applications.

Antifungal activities of silver and selenium nanoparticles stabilized with different surface coating agents.

BACKGROUND: Extensive and growing use of different chemical pesticides that affect both the environment and human health raises a need for new and more suitable methods to deal with plant pathogens. Nanotechnology has enabled the use of materials at the nanoscale with exceptional functionality in different economic domains including agricultural production. This study aimed to evaluate antifungal potential of selenium nanoparticles (SeNPs) and silver nanoparticles (AgNPs) stabilized with different surface coatings and characterized by different surface charge on plant pathogenic fungi Macrophomina phaseolina, Sclerotinia sclerotiorum and Diaporthe longicolla. RESULTS: AgNPs were coated with three different stabilizing agents: mono citrate (MC-AgNPs), cetyltrimethyl ammonium bromide (CTAB-AgNPs) and polyvinylpyrrolidon (PVP-AgNPs). SeNPs were coated with poly-l-lysine (PLL-SeNPs), polyacrylic acid (PAA-SeNPs), and polyvinylpyrrolidon (PVP-SeNPs). Seven different concentrations (0.1, 0.5, 1, 5, 10, 50 and 100 mg L-1 ) of nanoparticles were applied. All AgNPs and SeNPs significantly inhibited the growth of the tested fungi. Among the tested NPs, PVP-AgNPs showed the best inhibitory effect on the tested plant pathogenic fungi, especially against S. sclerotiorum. The similar inhibition of the sclerotia formation was observed for S. sclerotiorum treated with PLL-SeNPs. CONCLUSION: Obtained results provides new insights on fungicide effect of AgNPs and SeNPs stabilized with different coating agents on different plant pathogens. Further work should focus on detailed risk/benefit ratio assessment of using SeNPs or AgNPs in agriculture taking into account whole agroecosystem. © 2020 Society of Chemical Industry.

Stability and toxicity of differently coated selenium nanoparticles under model environmental exposure settings.

This study, motivated to fill the knowledge gap on environmental safety of selenium nanoparticles (SeNPs), provides information on the stability and environmental safety of four differently coated SeNPs rendering both positive and negative surface charges. The stability and dissolution behaviour of SeNPs were determined in an aquatic model media of different ionic strength to provide information regarding the environmental fate of SeNPs in different environmental conditions. The environmental safety of SeNPs was evaluated by acute regulatory toxicity tests using Daphina magna and Vibrio fischeri as model organisms. Agglomeration was observed for all studied SeNPs in test media with higher ionic strength caused by the disruption of surface charge leading to electrostatic instability. Toxicity of SeNPs on both aquatic species was dose-dependent and increased with exposure time. The obtained data indicated that all of the tested SeNPs could be classified as harmful to the natural bacteria V. fischeri and harmful to toxic to crustaceans D. magna, but dependent on the coating agent used for SeNPs stabilization. Although SeNPs have attracted great interest for use in biomedicine, this study demonstrated that their ecotoxicological effects should be considered during the design of new of SeNPs-based products.

Tailoring the stability/aggregation of one-dimensional TiO2(B)/titanate nanowires using surfactants.

The increased utilization of one-dimensional (1D) TiO2 and titanate nanowires (TNWs) in various applications was the motivation behind studying their stability in this work, given that stability greatly influences both the success of the application and the environmental impact. Due to their high abundance in aqueous environments and their rich technological applicability, surfactants are among the most interesting compounds used for tailoring the stability. The aim of this paper is to determine the influence of surfactant molecular structure on TNW stability/aggregation behavior in water and aqueous NaBr solution by dynamic and electrophoretic light scattering. To accomplish this, two structurally different quaternary ammonium surfactants (monomeric DTAB and the corresponding dimeric 12-2-12) at monomer and micellar concentrations were used to investigate TNW stability in water and NaBr. It was shown that TNWs are relatively stable in Milli-Q water. However, the addition of NaBr induces aggregation, especially as the TNW mass concentration increases. DTAB and 12-2-12 adsorb on TNW surfaces as a result of the superposition of favorable electrostatic and hydrophobic interactions. As expected, the interaction of TNWs with 12-2-12 was stronger than with DTAB, due to the presence of two positively charged head groups and two hydrophobic tails. As a consequence of the higher adsorption of 12-2-12, TNWs remained stable in both media, while DTAB showed an opposite behavior. In order to gain more insight into changes in the surface properties after surfactant adsorption on the TNW surface, a surface complexation model was employed. With this first attempt to quantify the contribution of the surfactant structure on the adsorption equilibrium according to the observed differences in the intrinsic log K values, it was shown that 12-2-12 interacts more strongly with TNWs than DTAB. The modelling results enable a better understanding of the interaction between TNWs and surfactants as well as the prediction of the conditions that can promote stabilization or aggregation.

Tuning the Viscoelastic-Gel Transition of Single-Wall Carbon Nanotubes Embedded in pH-Responsive Polyelectrolyte Solutions.

We present the detailed rheological changes that occur when small quantities of single-wall carbon nanotubes are dispersed in a poly(acrylic acid) water solution, around the overlap polymer concentration, up to the gel point. Here, pH is used to tune the gel formation. Suspensions of nanotubes at pH ≤ 5 are exfoliated and dispersed by the polymer. Contacts between the nanotubes are mainly through polymer entangling, and the suspension is viscoelastic. At pH > 5, the polymer is charged, and the solution is not a good solvent for the nanotubes anymore. Nanotube bundles covered with polymer are formed and mechanically percolate along the fluid until they become arrested. As a consequence, the rheological behavior is dominated by a mesoscale superstructure formed by nanotubes and polymer, where viscoelasticity is lost and the suspension becomes elastic. At pH ≥ 9, the surroundings for the nanotubes are worse, bundles and flocs grow to a larger extent, and they can be observable by scanning microscopies. When the suspension becomes a critical gel, the relaxation moduli can be modeled by a power law in the frequency domain in agreement with the model developed by Winter and co-workers.

Charge Properties of TiO2 Nanotubes in NaNO3 Aqueous Solution.

Charging of material surfaces in aqueous electrolyte solutions is one of the most important processes in the interactions between biomaterials and surrounding tissue. Other than a biomaterial, titania nanotubes (TiO2 NTs) represent a versatile material for numerous applications such as heavy metal adsorption or photocatalysis. In this article, the surface charge properties of titania NTs in NaNO3 solution were investigated through electrophoretic mobility and polyelectrolyte colloid titration measuring techniques. In addition, we used high-resolution transmission electron microscopy imaging to determine the morphology of TiO2 NTs. A theoretical model based on the classical density functional theory coupled with the charge regulation method in terms of mass action law was developed to understand the experimental data and to provide insights into charge properties at different physical conditions, namely, pH and NaNO3 concentration. Two intrinsic protonation constants and surface site density have been obtained. The electrostatic properties of the system in terms of electrostatic potentials and ion distributions were calculated and discussed for various pH values. The model can quantitatively describe the titration curve as a function of pH for higher bulk salt concentrations and the difference in the equilibrium amount of charges between the inner and outer surfaces of TiO2 NTs. Calculated counterion (NO3-) distributions show a pronounced decrease of NO3- ions for high bulk pH (both inside and outside TiO2 NT) because of the strong electric field. With the decrease of bulk pH or the increase of the salt concentration, NO3- is able to accumulate near the TiO2 NTs surfaces.

Biocompatibility assessment of up-and down-converting nanoparticles: implications of interferences with in vitro assays.

The safety assessment of nanoparticles (NPs) is crucial during their design and development for biomedicine. One of the prerequisite steps during this evaluation is in vitro testing that employs cell-based assays not always validated and well-adapted for NPs. Interferences with in vitro assays may arise due to the nano-related optical, oxidative, fluorescent, surface and catalytic properties of NPs. Thus, proper validation of each assay system has to be performed for each NP type. This study aimed to evaluate the applicability of the most common in vitro cytotoxicity assays for the safety assessment of up- and down-converting lanthanide-doped NPs. Conventional cell viability tests and fluorescence-based assays for oxidative stress response were selected to determine the biological effects of up- and down-converting NPs to human brain cells. Comparison with known silver and iron oxide NPs was made for verification purposes. Both the plate reader and flow cytometric measurements were examined. The obtained results indicated that both types of Ln-doped NPs interfered to a much lesser extent than metallic NPs. In addition, the great potential of both up- and down-converting NPs for biomedicine was manifested due to their biocompatibility and low toxicity.

Surface and zeta-potentials of silver halide single crystals: pH-dependence in comparison to particle systems.

We have carried out surface and zeta-potential measurements on AgCl and AgBr single crystals. As for particle systems we find that, surprisingly and previously unnoted, the zeta-potential exhibits pH-dependence, while the surface potential does not. A possible interpretation of these observations is the involvement of water ions in the interfacial equilibria and in particular, stronger affinity of the hydroxide ion compared to the proton. The pH-dependence of the zeta-potential can be suppressed at sufficiently high silver concentrations, which agrees with previous measurements in particle systems where no pH-dependence was found at high halide ion concentrations. The results suggest a subtle interplay between the surface potential determining the halide and silver ion concentrations, and the water ions. Whenever the charge due to the halide and silver ions is sufficiently high, the influence of the proton/hydroxide ion on the zeta-potential vanishes. This might be related to the water structuring at the relevant interfaces which should be strongly affected by the surface potential. Another interesting observation is accentuation of the assumed water ion effect on the zeta-potential at the flat single crystal surfaces compared to the corresponding silver halide colloids. Previous generic MD simulations have indeed predicted that hydroxide ion adsorption is accentuated on flat/rigid surfaces. A thermodynamic model for AgI single crystals was developed to describe the combined effects of iodide, silver and water ions, based on two independently previously published models for AgI (that only consider constituent and background electrolyte ions) and inert surfaces (that only consider water and background electrolyte ions). The combined model correctly predicts all the experimentally observed trends.

pH and the surface tension of water.

Despite the strong adsorption of hydroxide ions, the surface tension of water is almost independent of pH between pH 1 and 13 when the pH is adjusted by addition of HCl or NaOH. This is consistent with the Gibbs adsorption isotherm which measures the surface excess of all species in the double layer, if hydronium ions and hydroxide ions are adsorbed and sodium and chloride ions are not. The surface tension becomes pH dependent around pH 7 in millimolar NaCl or KCl solutions, for now sodium ions can replace hydronium ions as counterions to the adsorbed hydroxide ions.