Viewpoint: Atomic-Scale Design Protocols toward Energy, Electronic, Catalysis, and Sensing Applications.

Nanostructured materials are essential building blocks for the fabrication of new devices for energy harvesting/storage, sensing, catalysis, magnetic, and optoelectronic applications. However, because of the increase of technological needs, it is essential to identify new functional materials and improve the properties of existing ones. The objective of this Viewpoint is to examine the state of the art of atomic-scale simulative and experimental protocols aimed to the design of novel functional nanostructured materials, and to present new perspectives in the relative fields. This is the result of the debates of Symposium I "Atomic-scale design protocols towards energy, electronic, catalysis, and sensing applications", which took place within the 2018 European Materials Research Society fall meeting.

Interface-Driven Strain in Heavy Ion-Irradiated Zr/Nb Nanoscale Metallic Multilayers: Validation of Distortion Modeling via Local Strain Mapping.

Nanolayered metallic alloys are promising materials for nuclear applications thanks to their resistance to radiation damage. Here, we investigate the effect of ion (C, Si, and Cu) irradiation at room temperature with different fluences into sputtered Zr/Nb metallic multilayer films with periods 27 nm (thin) and 96 nm (thick). After irradiation, while a high strain in the entire thin nanoscale metallic multilayer (NMM) is observed, a quite small strain in the entire thick NMM is established. This difference is further analyzed by a semianalytical model, and the reasons behind it are revealed, which are also validated by local strain mapping. Both methods show that within a thick layer, two opposite distortions occur, making the overall strain small, whereas in a thin layer, all the atomic planes are affected by the interface and are subjected to only a single type of distortion (Nb─tension and Zr─compression). In both thin and thick NMMs, with increasing damage, the strain around the interface increases, resulting in a release of the elastic energy at the interface (decrease in the lattice mismatch), and the radiation-induced transition of the Zr/Nb interfaces from incoherent to partially coherent occurs. Density functional theory simulations decipher that the inequality of point defect diffusion flux from the inner to the interface-affected region is responsible for the presence of opposite distortions within a layer. Technologically, based on this work, we estimated that Zr/Nb55 with thicknesses around Zr = 24 nm and Nb = 31 nm is the most promising multilayer system with the high radiation damage resistance and minimum swelling for nuclear applications.

Deformation-Controlled Design of Metallic Nanocomposites.

Achieving the theoretical strength of a metallic alloy material is a demanding task that usually requires utilizing one or more of the well-established routes: (1) Decreasing the grain size to stop or slow down the dislocation mobility, (2) adding external barriers to dislocation pathways, (3) altering the crystal structure, or (4) combining two of the previous discrete strategies, that is, implementing crystal seeds into an amorphous matrix. Each of the outlined methods has clear limitations; hence, further improvements are required. We present a unique approach that envelops all the different strength-building strategies together with a new phenomenon-phase transition. We simulated the plastic deformation of a Zr-Nb nanolayered alloy using molecular dynamics and ab initio methods and observed the transition of Zr from hexagonal close-packed to face-centered cubic and then to body-cenetered cubic during compression. The alloy, which was prepared by magnetron sputtering, exhibited near-theoretical hardness (10.8 GPa) and the predicted transition of the Zr structure was confirmed. Therefore, we have identified a new route for improving the hardness of metallic alloys.

Molecular entrapment of volatile organic compounds (VOCs) by electrospun cyclodextrin nanofibers.

In this paper, we reported the molecular entrapment performance of hydroxypropyl-beta-cyclodextrin (HPßCD) and hydroxypropyl-gamma-cyclodextrin (HPγCD) electrospun nanofibers (NF) for two common volatile organic compounds (VOCs); aniline and benzene. The encapsulation efficiency of CD samples were investigated depending on the various factors such as; CD form (NF and powder), electrospinning solvent (DMF and water), CD (HPßCD and HPγCD) and VOCs (aniline and benzene) types. BET analysis indicated that, electrospun CD NF have higher surface area compared to their powder form. In addition DMA measurement provided information about the mechanical properties of CD NF. The encapsulation capability of CD NF and CD powder was investigated by (1)H-NMR and HPLC techniques. The observed results suggested that, CD NF can entrap higher amount of VOCs from surroundings compared to their powder forms. Besides, molecular entrapment efficiency of CD NF also depends on CD, solvent and VOCs types. The inclusion complexation between CD and VOCs was determined by using TGA technique, from the higher decomposition temperature of VOCs. Finally, our results were fortified by the modeling studies which indicated the complexation efficiency variations between CD and VOC types. Here, the inclusion complexation ability of CD molecules was combined with very high surface area and versatile features of CD NF. So these findings revealed that, electrospun CD NF can serve as useful filtering material for air filtration purposes due to their molecular entrapment capability of VOCs.

Sulfisoxazole/cyclodextrin inclusion complex incorporated in electrospun hydroxypropyl cellulose nanofibers as drug delivery system.

Herein, hydroxypropyl-beta-cyclodextrin (HPßCD) inclusion complex (IC) of a hydrophobic drug, sulfisoxazole (SFS) was incorporated in hydroxypropyl cellulose (HPC) nanofibers (HPC/SFS/HPßCD-IC-NF) via electrospinning. SFS/HPßCD-IC was characterized by DSC to investigate the formation of inclusion complex and the stoichiometry of the complex was determined by Job's plot. Modeling studies were also performed on SFS/HPßCD-IC using ab initio technique. SEM images depicted the defect free uniform fibers and confirmed the incorporation of SFS/HPßCD-IC in nanofibers did not alter the fiber morphology. XRD analyses showed amorphous distribution of SFS/HPßCD-IC in the fiber mat. Release studies were performed in phosphate buffered saline (PBS). The results suggest higher amount of SFS released from HPC/SFS/HPßCD-IC-NF when compared to free SFS containing HPC nanofibers (HPC/SFS-NF). This was attributed to the increased solubility of SFS by inclusion complexation. Sandwich configurations were prepared by placing HPC/SFS/HPßCD-IC-NF between electrospun PCL nanofibrous mat (PCL-HPC/SFS/HPßCD-IC-NF). Consequently, PCL-HPC/SFS/HPßCD-IC-NF exhibited slower release of SFS as compared with HPC/SFS/HPßCD-IC-NF. This study may provide more efficient future strategies for developing delivery systems of hydrophobic drugs.

Spontaneous high piezoelectricity in poly(vinylidene fluoride) nanoribbons produced by iterative thermal size reduction technique.

We produced kilometer-long, endlessly parallel, spontaneously piezoelectric and thermally stable poly(vinylidene fluoride) (PVDF) micro- and nanoribbons using iterative size reduction technique based on thermal fiber drawing. Because of high stress and temperature used in thermal drawing process, we obtained spontaneously polar γ phase PVDF micro- and nanoribbons without electrical poling process. On the basis of X-ray diffraction (XRD) analysis, we observed that PVDF micro- and nanoribbons are thermally stable and conserve the polar γ phase even after being exposed to heat treatment above the melting point of PVDF. Phase transition mechanism is investigated and explained using ab initio calculations. We measured an average effective piezoelectric constant as -58.5 pm/V from a single PVDF nanoribbon using a piezo evaluation system along with an atomic force microscope. PVDF nanoribbons are promising structures for constructing devices such as highly efficient energy generators, large area pressure sensors, artificial muscle and skin, due to the unique geometry and extended lengths, high polar phase content, high thermal stability and high piezoelectric coefficient. We demonstrated two proof of principle devices for energy harvesting and sensing applications with a 60 V open circuit peak voltage and 10 µA peak short-circuit current output.