Hydrosilylation Adducts to Produce Wide-Temperature Flexible Polysiloxane Aerogel under Ambient Temperature and Pressure Drying.

Despite incorporation of organic groups into silica-based aerogels to enhance their mechanical flexibility, the wide temperature reliability of the modified silicone aerogel is inevitably degraded. Therefore, facile synthesis of soft silicone aerogels with wide-temperature stability remains challenging. Herein, novel silicone aerogels containing a high content of Si are reported by using polydimethylvinylsiloxane (PDMVS), a hydrosilylation adduct with water-repellent groups, as a "flexible chain segment" embedded within the aerogel network. The poly(2-dimethoxymethylsilyl)ethylmethylvinylsiloxane (PDEMSEMVS) aerogel is fabricated through a cost-effective ambient temperature/pressure drying process. The optimized aerogel exhibits exceptional performance, such as ultra-low density (50 mg cm-3), wide-temperature mechanical flexibility, and super-hydrophobicity, in comparison to the previous polysiloxane aerogels. A significant reduction in the density of these aerogels is achieved while maintaining a high crosslinking density by synthesizing gel networks with well-defined macromolecules through hydrolytic polycondensation crosslinking of PDEMSEMVS. Notably, the pore/nanoparticle size of aerogels can be fine-tuned by optimizing the gel solvent type. The as-prepared silicone aerogels demonstrate selective absorption, efficient oil-water separation, and excellent thermal insulation properties, showing promising applications in oil/water separation and thermal protection.

Engineering Sulfur-Containing Polymeric Fire-Retardant Coatings for Fire-Safe Rigid Polyurethane Foam.

With the advantages of lightweight and low thermal conductivity properties, polymeric foams are widely employed as thermal insulation materials for energy-saving buildings but suffer from inherent flammability. Flame-retardant coatings hold great promise for improving the fire safety of these foams without deteriorating the mechanical-physical properties of the foam. In this work, four kinds of sulfur-based flame-retardant copolymers are synthesized via a facile radical copolymerization. The sulfur-containing monomers serve as flame-retardant agents including vinyl sulfonic acid sodium (SPS), ethylene sulfonic acid sodium (VS), and sodium p-styrene sulfonate (VSS). Additionally, 2-hydroxyethyl acrylate (HEA) and 4-hydroxybutyl acrylate are employed to enable a strong interface adhesion with polymeric foams through interfacial H-bonding. By using as-synthesized waterborne flame-retardant polymeric coating with a thickness of 600 µm, the coated polyurethane foam (PUF) can achieve a desired V-0 rating during the vertical burning test with a high limiting oxygen index (LOI) of >31.5 vol%. By comparing these sulfur-containing polymeric fire-retardant coatings, poly(VS-co-HEA) coated PUF demonstrates the best interface adhesion capability and flame-retardant performance, with the lowest peak heat release rate of 166 kW m-2 and the highest LOI of 36.4 vol%. This work provides new avenues for the design and performance optimization of advanced fire-retardant polymeric coatings.

Effects of Ammonium Polyphosphate and Organic Modified Montmorillonite on Flame Retardancy of Polyethylene Glycol/Wood-Flour-Based Phase Change Composites.

With the depletion of fossil fuel energy and both the slow development and low utilization rate of new eco-friendly energy, finding new ways to efficiently store energy has become a research hotspot. Presently, polyethylene glycol (PEG) is an excellent heat storage material, but it is a typical solid-liquid phase change material (PCM) with a risk of leakage during phase transition. A combination of wood flour (WF) and PEG can effectively eliminate the risk of leakage after the melting of PEG. However, WF and PEG are both flammable materials, which impedes their application. Therefore, it is of great significance to expand their application by forming composites from among PEG, supporting mediums, and flame-retardant additives. This will improve both their flame retardancy and phase change energy storage performance, and will also lead to the preparation of excellent flame-retardant phase change composite materials with solid-solid phase change characteristics. To address this issue, ammonium polyphosphate (APP), organic modified montmorillonite (OMMT), and WF were blended into PEG in specific proportions to prepare a series of PEG/WF-based composites. Both thermal cycling tests and thermogravimetric analysis results demonstrated that the as-prepared composites had good thermal reliability and chemical stability. In addition, during differential scanning calorimetry tests, the PEG/WF/8.0APP@2.0OMMT composite presented the highest melting latent heat (176.6 J/g), and its enthalpy efficiency reached more than 98.3%. The PEG/WF/8.0APP@2.0OMMT composite also exhibited superior thermal insulation performance when compared to the pure PEG/WF composite. Furthermore, the PEG/WF/8.0APP@2.0OMMT composite exhibited a significant 50% reduction in peak heat release rate as a result of the synergistic effect between OMMT and APP in the gas and condensed phases. This work offers a useful strategy for the fabrication of multifunctional phase-change material, which is expected to broaden its industrial applications.

Synergistic Function between Phosphorus-Containing Flame Retardant and Multi-Walled Carbon Nanotubes towards Fire Safe Polystyrene Composites with Enhanced Electromagnetic Interference Shielding.

As a universal polymer material, polystyrene (PS) is widely applied in electrical devices and construction. Thus, it is necessary to improve the flame retardancy and electromagnetic shielding properties of PS material. In this work, PS/silicon-wrapped ammonium polyphosphate/Inorganic acid-treated multi-walled carbon nanotubes composites (PS/SiAPP/aMWCNT, abbreviated as PAC) were prepared via methods of filtration-induced assembly and hot-pressing. Morphology and structure characterization demonstrated that SiAPP and aMWCNT had good dispersion in PS and excellent compatibility with the PS matrix. Thermogravimetric analysis revealed that the addition of aMWCNT to PS improved its thermal stability and carbon-forming characteristics. The peak heat release rate, the peak carbon monoxide production rate, and the peak smoke production rate of the PAC10 composite decreased by 53.7%, 41.9%, and 45.5%, respectively, while its electromagnetic shielding effectiveness reached 12 dB. These enhancements were attributed to the reason that SiAPP and aMWCNT synergistically catalyzed the char generation and SiAPP produced free radical scavengers and numbers of incombustible gases, which could decrease the oxygen concentration and retard the combustion reaction. Therefore, the assembled PS/SiAPP/aMWCNT system provides a new pathway to improve the flame retardant and electromagnetic shielding properties of PS.

Efficient adsorption of diclofenac sodium in water by a novel functionalized cellulose aerogel.

In this work, a novel cellulose aerogel (CNC-PVAm/rGO) was fabricated using cellulose nanocrystalline (CNC) modified with polyvinylamine (PVAm) and reduced graphene oxide (rGO). The resultant CNC-PVAm/rGO was then applied for the adsorption of diclofenac sodium (DCF), a typical non-steroidal anti-inflammatory drug. Characterization using ultra-high-resolution field emission scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and the Brunauer-Emmett-Teller surface area revealed that the obtained CNC-PVAm/rGO displayed an evident 3D porous structure, which had an ultralight weight, good recovery, abundant surface functional groups (e.g., -NH2 and -OH), and rGO nanosheets. In addition, the material presented a stable crystal structure and large specific surface area (105.73 m2 g-1). During the adsorption of DCF, the CNC-PVAm/rGO aerogel showed a rather excellent adsorption performance, with a maximum adsorption capacity (qmax) of 605.87 mg g-1, which was approximately 53 times larger than that of the bare CNC aerogel (11.45 mg g-1). The adsorption performance of CNC-PVAm/rGO was also better than that of other reported adsorbents. The adsorption of DCF to CNC-PVAm/rGO obeyed the Langmuir isotherm and pseudo-second-order kinetic models, and underwent a spontaneous exothermic process. Moreover, DCF was easily desorbed from CNC-PVAm/rGO with sodium hydroxide solution (0.1 mol L-1), and the absorbent could be reused four times. The introduction of PVAm and rGO to the CNC-PVAm/rGO aerogel also greatly enhanced electrostatic interactions, π-π interactions, and hydrophobic effects. These enhancements significantly promoted the hydrogen bonding interactions between the DCF molecules and CNC-PVAm/rGO, thus resulting in a large improvement in the adsorption performance of the aerogel.

Improving the clinical outcomes by extended culture of day 3 embryos with low blastomere number to blastocyst stage following frozen-thawed embryo transfer.

PURPOSE: This study aimed to investigate whether the extended culture of day 3 (D3) embryos with low blastomere number to blastocyst following frozen-thawed embryo transfer improved the clinical outcomes. METHODS: This was a retrospective study of clinical data of women undergoing in vitro fertilization/intracytoplasmic sperm injection (IVF/ICSI) cycles in the Tangdu Hospital. The patients were divided into groups with 4-5, 6, 7-9 and > 9 cells based on the blastomere number of D3 embryos. The clinical outcomes were compared. RESULTS: In fresh transfer cycles, the implantation and clinical pregnancy rates significantly decreased, while the abortion rate significantly increased in the groups with 4-5 and 6 cells compared with those with 7-9 and > 9 cells. In frozen-thawed transfer cycles, the clinical pregnancy and implantation rates for a single blastocyst transfer cycle showed no significant differences in the groups with 4-5 and 6 cells compared with those with 7-9 and > 9 cells. However, the abortion rate was significantly higher in the group with 4-5 cells than in that with 7-9 and > 9 cells. In the double blastocyst transfer cycle, the clinical pregnancy rate showed no significant differences among the groups with 4-5, 6, and 7-9 cells. CONCLUSION: The implantation and clinical pregnancy rates of D3 embryos with 6 cells significantly decreased; these embryos were not considered as high-quality embryos. Extended culture of D3 embryos with ≤ 6 blastomeres to blastocysts, particularly 6-cell embryos, resulted in a similar clinical pregnancy rate as that of blastocysts derived from D3 embryos with ≥ 7 blastomeres.

Enhanced Fire Safety of Rigid Polyurethane Foam via Synergistic Effect of Phosphorus/Nitrogen Compounds and Expandable Graphite.

In order to explore highly efficient flame-retardant rigid polyurethane foam (RPUF), phosphorus/nitrogen compounds and expandable graphite (EG) were successfully incorporated into RPUF by a free one-spot method. The combustion results showed that the fire safety of the RPUF samples was remarkably improved by the addition of phosphoric/nitrogen compounds and EG. With the incorporation of 22.4 wt.% phosphorus/nitrogen compounds and 3.2 wt.% EG, the RPUF composites achieved UL-94 V-0 rating. Besides, the total heat release and total smoke release of RPUF composites were reduced by 29.6% and 32.4% respectively, compared to those of the pure RPUF sample. PO• and PO2• together with nonflammable gaseous products were evolved from phosphoric/nitrogen compounds in the gas phase, which quenched the flammable free radicals in the matrix and diluted the concentration of combustible gaseous products generated from PRUF during combustion. The compact char residues which acted as excellent physical barriers were formed by catalysis of EG and phosphoric/nitrogen compounds in the condense phase. The fire hazard of RPUF was significantly reduced by the synergistic effect of phosphorus-nitrogen compounds and EG. This work provides a promising strategy to enhance the fire safety of RPUF.

Loss of methylation of H19-imprinted gene derived from assisted reproductive technologies can be mitigated by cleavage-stage embryo transfer in mice.

PURPOSE: Studies on rodents have shown that assisted reproductive technologies (ARTs) are associated with perturbation of genomic imprinting in blastocyst-stage embryos. However, the vulnerable developmental window for ART influence on the genomic imprinting of embryos is still undetermined. The purpose of this study was to establish the specific embryonic development stage at which the loss of methylation of H19 imprinting control regions (ICRs) was caused by ART occurrence. Additionally, we explored protocols to safeguard against possible negative impacts of ART on embryo H19 imprinting. METHODS: Mouse embryos were generated under four different experimental conditions, divided into four groups: control, in vitro culture (IVC), in vitro fertilization (IVF), and intracytoplasmic sperm injection (ICSI). The methylation levels of H19 ICR of the grouped or individual embryos were analyzed by bisulfite-sequencing PCR. RESULTS: Our data showed that the loss of methylation of H19 ICR in mouse blastocysts was inflicted to a similar extent by IVC, IVF, and ICSI. Specifically, we observed a significant loss of methylation of H19 ICR between the mouse 8-cell and morula stages. In addition, we revealed that the transfer of mouse embryos generated by ARTs in the uterus at the 8-cell stage induced the occurrence of methylation patterns in the blastocysts closer to the in vivo ones. CONCLUSIONS: Our findings indicate that the loss of methylation of H19 ICR caused by ARTs occurs between the 8-cell and the morula stages, and the transfer of cleavage embryos to the uterus mitigates the loss methylation of H19 derived by mice ARTs.

Water vapor assisted aramid nanofiber reinforcement for strong, tough and ionically conductive organohydrogels as high-performance strain sensors.

Conductive organohydrogels have gained increasing attention in wearable sensors, flexible batteries, and soft robots due to their exceptional environment adaptability and controllable conductivity. However, it is still difficult for conductive organohydrogels to achieve simultaneous improvement in mechanical and electrical properties. Here, we propose a novel "water vapor assisted aramid nanofiber (ANF) reinforcement" strategy to prepare robust and ionically conductive organohydrogels. Water vapor diffusion can induce the pre-gelation of the polymer solution and ensure the uniform dispersion of ANFs in organohydrogels. ANF reinforced organohydrogels have remarkable mechanical properties with a tensile strength, stretchability and toughness of up to 1.88 ± 0.04 MPa, 633 ± 30%, and 6.75 ± 0.38 MJ m-3, respectively. Furthermore, the organohydrogels exhibit great crack propagation resistance with the fracture energy and fatigue threshold as high as 3793 ± 167 J m-2 and ∼328 J m-2, respectively. As strain sensors, the conductive organohydrogel demonstrates a short response time of 112 ms, a large working strain and superior cycling stability (1200 cycles at 40% strain), enabling effective monitoring of a wide range of complex human motions. This study provides a new yet effective design strategy for high performance and multi-functional nanofiller reinforced organohydrogels.

Large-Scale, Mechanically Robust, Solvent-Resistant, and Antioxidant MXene-Based Composites for Reliable Long-Term Infrared Stealth.

MXene-based thermal camouflage materials have gained increasing attention due to their low emissivity, however, the poor anti-oxidation restricts their potential applications under complex environments. Various modification methods and strategies, e.g., the addition of antioxidant molecules and fillers have been developed to overcome this, but the realization of long-term, reliable thermal camouflage using MXene network (coating) with excellent comprehensive performance remains a great challenge. Here, a MXene-based hybrid network comodified with hyaluronic acid (HA) and hyperbranched polysiloxane (HSi) molecules is designed and fabricated. Notably, the presence of appreciated HA molecules restricts the oxidation of MXene sheets without altering infrared stealth performance, superior to other water-soluble polymers; while the HSi molecules can act as efficient cross-linking agents to generate strong interactions between MXene sheets and HA molecules. The optimized MXene/HA/HSi composites exhibit excellent mechanical flexibility (folded into crane structure), good water/solvent resistance, and long-term stable thermal camouflage capability (with low infrared emissivity of ≈0.29). The long-term thermal camouflage reliability (≈8 months) under various outdoor weathers and the scalable coating capability of the MXene-coated textile enable them to disguise the IR signal of various targets in complex environments, indicating the great promise of achieved material for thermal camouflage, IR stealth, and counter surveillance.

A facile strategy for constructing lightweight, fire safety and compression resistance poly(vinylalcohol) aerogels with highly-efficient expansible graphene oxide/layered double hydroxides hybrid synergistic flame retardant.

Poly(vinyl alcohol) (PVA) aerogels with excellent environmentally friendly properties have been considered to replace undegradable polymer foams. However, due to highly flammable, hydrophilic, and worse compression resistance performance, PVA aerogels have always been excluded from practical. Herein, a fire safety and compression resistance PVA/expansible graphene oxide (EGO)/Layered double hydroxides (LDHs) (PGL) aerogel was prepared via the freeze-drying method and electrostatic adsorption of flame retardant. The ice crystals from aerogels were sublimated and left a mass of tree-like pore tunnel structures. Meantime, the compound of EGO and LDHs rendered PGL aerogels high compressive strength of 6.0917 MPa (at 80% of strains), a high specific modulus of 19.16 m2/s2, and an ultra-low density of 0.059 g/cm3. Especially, the as-prepared PGL aerogels showed heat release reduced by 55.4%, smoke release reduced by 54.3%, and the limiting oxygen index reaching up to 31%. Moreover, LDHs also enhanced the interface with PVA/EGO resulting in hydrophobic performance improvement. The proposed enhancements mechanism suggested that (i) chemical reactions between EGO and PVA matrix; (ii) a mass of negative potential sites from the interface of PVA/EGO composites made LDHs sheets easily adsorbing; (iii) oxygen-containing groups from EGO and LDHs absorbed mass of heat during combustion; (iv) the compact char residues on the surface of aerogels acting as barriers suppressed smoke and prevented PVA matrix from further combustion. Therefore, electrostatic adsorption as a facile production process was paved for meeting the compression resistance, flame-retardant, heat-insulating, and smoke-suppressed requirements of PVA aerogels in this work.

Architecting fire safe hierarchical polymer nanocomposite films with excellent electromagnetic interference shielding via interface engineering.

Integrating high flame retardancy and excellent electromagnetic interference (EMI) shielding into polymetric materials is extremely necessary, and well dispersing conductive fillers into polymeric materials is still a great challenge because of incompatible interfacial polarity between polymer matrix and conductive fillers. Therefore, under the premise of maintaining integral conductive films in the process of hot compression, constructing a novel EMI shielding polymer nanocomposites where conductive films closely adhere to polymer nanocmposites layers should be a fascinating stratety. In this work, salicylaldehyde-modified chitosan decorated titanium carbide nanohybrid (Ti3C2Tx-SCS) was combined with piperazine-modified ammonium polyphosphate (PA-APP) to fabricate thermoplastic polyurethane (TPU) nanocomposites, which were used for construction of hierarchical nanocomposite films by inserting reduced graphene oxide (rGO) films into TPU/PA-APP/Ti3C2Tx-SCS nanocomposite layers through our self-developed air assisted hot pressing technique. The total heat release, total smoke release and total carbon monoxide yield for TPU nanocomposite containing 4.0 wt% Ti3C2Tx-SCS nanohybrid were 58.0%, 58.4% and 75.8% lower than those of pristine TPU, respectively. Besides, the hierarchical TPU nanocomposite film containing 1.0 wt% Ti3C2Tx-SCS presented an averaged EMI shielding effectiveness of 21.3 dB in X band. This work provides a promising strategy for fabricating fire safe and EMI shielding polymer nanocomposites.

Tunable construction of fire safe and mechanically strong hierarchical composites towards electromagnetic interference shielding.

Cotton fabric composites were designed to be protected by fire safe thermoplastic polyurethane (TPU) composites for developing electromagnetic interference (EMI) shielding polymer composites with superior mechanical properties. Herein, the as-prepared MXene was coated onto the fiber surface of cotton and then thermally compressed with TPU composites, which were filled with the sodium dodecyl sulfate modified layered double hydroxides functionalized the short carbon fiber hybrids through melt blending method. Then, a series of highly fire safe cotton/TPU hierarchical composites were constructed by a designed thermal compression technique. For instance, the obtained cotton/TPU hierarchical sample showed greatly reduced peak of heat release rate, peak of carbon monoxide production rate and peak of carbon dioxide production rate of TPU by 50.1%, 52.1% and 55.4%, respectively. Furthermore, the cotton/TPU hierarchical composites possessed the EMI shielding effectiveness of 40.0 dB in the X band and 54.6 dB in the K band. The mechanical property of the cotton/TPU hierarchical composites was also reinforced, where the elongation at break and toughness values of the TPU/SCF/mLDH1/C2 hierarchical composite were 21.47 and 18.30 times higher than those of pure TPU, respectively. These mechanically strong hierarchical composites have brought a promising attempt to broaden their practical application, removing the fire hazards and electromagnetic waves radiation from the environment.

Stretchable, durable and asymmetrically wettable nanofiber composites with unidirectional water transportation capability for temperature sensing.

The one-way transportation of liquids plays an important role in smart and wearable electronics. Here, we report an asymmetric nanofibrous membrane (ANM) with unidirectional water transport (UWT) capability by integrating one superhydrophilic MXene/Chitosan/Polyurethane (PU) nanofiber membrane (MCPNM) and one ultrathin hydrophobic PU/Polyvinylpyrrolidone (PVP) layer with a "bead-on-string" structure. The UWT performance shows long-term stability and can be well maintained during the cyclic stretching, abrasion and ultrasonic washing tests. The ANM exhibits negative temperature coefficient and is served as a temperature sensor to monitor the temperature variation of the environment, which can provide efficient alarm signals in a hot or cold condition. When attached on person's skin, the ANM displays a unique anti-gravity UWT behavior. The stretchable, wearable and multi-functional nanofibrous composite membrane with an asymmetric wettability shows potential applications in flexible and wearable electronics, health monitoring, etc.

Fabrication of covalent organic frameworks modified nanofibrous membrane for efficiently enriching and detecting the trace polychlorinated biphenyls in water.

Enriching and detecting the trace pollutants in actual matrices are critical to evaluating the water quality. Herein, a novel nanofibrous membrane, named PAN-SiO2@TpPa, was prepared by in situ growing ß-ketoenamine-linked covalent organic frameworks (COF-TpPa) on the aminated polyacrylonitrile (PAN) nanofibers, and adopted for enriching the trace polychlorinated biphenyls (PCBs) in various natural water body (river, lake and sea water) through the solid-phase micro-extraction (SPME) process. The resulted nanofibrous membrane owned abundant functional groups (-NH-, -OH and aromatic groups), outstandingly thermal and chemical stability, and excellent ability in extracting PCBs congeners. Based on the SPME process, the PCBs congeners could be quantitatively analyzed by the traditional gas chromatography (GC) method, with the satisfactory linear relationship (R2>0.99), low detection limit (LODs, 0.1∼5 ng L-1), high enrichment factors (EFs, 2714∼3949) and multiple recycling (>150 runs). Meanwhile, when PAN-SiO2@TpPa was adopted in the real water samples, the low matrix effects on the enrichment of PCBs at both 5 and 50 ng L-1 over PAN-SiO2@TpPa membrane firmly revealed the feasibility of enriching the trace PCBs in real water. Besides, the related mechanism of extracting PCBs on PAN-SiO2@TpPa mainly involved the synergistic effect of hydrophobic effect, π-π stacking and hydrogen bonding.

Nanofiber Composite Reinforced Organohydrogels for Multifunctional and Wearable Electronics.

Composite organohydrogels have been widely used in wearable electronics. However, it remains a great challenge to develop mechanically robust and multifunctional composite organohydrogels with good dispersion of nanofillers and strong interfacial interactions. Here, multifunctional nanofiber composite reinforced organohydrogels (NCROs) are prepared. The NCRO with a sandwich-like structure possesses excellent multi-level interfacial bonding. Simultaneously, the synergistic strengthening and toughening mechanism at three different length scales endow the NCRO with outstanding mechanical properties with a tensile strength (up to 7.38 ± 0.24 MPa), fracture strain (up to 941 ± 17%), toughness (up to 31.59 ± 1.53 MJ m-3) and fracture energy (up to 5.41 ± 0.63 kJ m-2). Moreover, the NCRO can be used for high performance electromagnetic interference shielding and strain sensing due to its high conductivity and excellent environmental tolerance such as anti-freezing performance. Remarkably, owing to the organohydrogel stabilized conductive network, the NCRO exhibits superior long-term sensing stability and durability compared to the nanofiber composite itself. This work provides new ideas for the design of high-strength, tough, stretchable, anti-freezing and conductive organohydrogels with potential applications in multifunctional and wearable electronics.

Intelligent cyclic fire warning sensor based on hybrid PBO nanofiber and montmorillonite nanocomposite papers decorated with phenyltriethoxysilane.

An abundance of early warning graphene-based nano-materials and sensors have been developed to avoid and prevent the critical fire risk of combustible materials. However, there are still some limitations that should be addressed, such as the black color, high-cost and single fire warning response of graphene-based fire warning materials. Herein, we report an unexpected montmorillonite (MMT)-based intelligent fire warning materials that have excellent fire cyclic warning performance and reliable flame retardancy. Combining phenyltriethoxysilane (PTES) molecules, poly(p-phenylene benzobisoxazole) nanofiber (PBONF), and layers of MMT to form a silane crosslinked 3D nanonetwork system, the homologous PTES decorated MMT-PBONF nanocomposites are designed and fabricated via a sol-gel process and low temperature self-assembly method. The optimized nanocomposite paper shows good mechanical flexibility (good recovery after kneading or bending process), high tensile strength of âˆ¼81 MPa and good water resistance. Furthermore, the nanocomposite paper exhibits high-temperature flame resistance (almost unchanged structure and size after 120 s combustion), sensitive flame alarm response (∼0.3 s response once exposure onto a flame), cyclic fire warning performance (>40 cycles), and adaptability to complex fire situations (several fire attack and evacuation scenarios), showing promising applications for monitoring the critical fire risk of combustible materials. Therefore, this work paves a rational way for design and fabrication of MMT-based smart fire warning materials that combine excellent flame shielding and sensitive fire alarm functions.

[Telomere lengthening by trichostatin A treatment in cloned pigs].

Telomeres are repeated GC rich sequences at the end of chromosomes, and shorten with each cell division due to DNA end replication problem. Previously, reprogrammed somatic cells of cloned animals display variable telomere elongation. However, it was reported that the cloned animals including Dolly do not reset telomeres and show premature aging. In this study, we investigated telomere function in cloned or transgenic cloned pigs, including the cloned Northeast Min pigs, eGFP, Mx, and PGC1α transgenic cloned pigs, and found that the telomere lengths of cloned pigs were significantly shorter than the nuclear donor adult fibroblasts and age-matched noncloned pigs (P<0.05), indicating that nuclear reprogramming did not restore cellular age of donor cells after somatic cell nuclear transfer (SCNT). Trichostatin A (TSA), an inhibitor of histone deacetylase, has proven to enhance the efficiency of nuclear reprogramming in several species. In order to test whether TSA also can effectively enhance reprogramming of telomeres, TSA (40 nmol/L) was used to treat porcine cloned embryos at 1-cell stage for 24 h. Consistent with previous reports, the developmental rate of SCNT embryos to the blastocyst stage was significantly increased compared with those of the control group (16.35% vs. 27.09%, 21.60% vs. 34.90%, P<0.05). Notably, the telomere length of cloned porcine blastocysts was also significantly elongated (P<0.05). Although TSA did not improve the cloning efficiency (1.3% vs. 1.7%, TSA vs. control), the telomere lengths of cloned pig-lets were significantly longer compared with those of the control group and the donor fibroblasts (P<0.05). In conclusion, telomeres have not been effectively restored by SCNT in pigs but TSA can effectively lengthen the telomere lengths of cloned pigs.

Efficient extraction of trace organochlorine pesticides from environmental samples by a polyacrylonitrile electrospun nanofiber membrane modified with covalent organic framework.

Detecting and analyzing of the trace organochlorine pesticides (OCPs) in the real water has become a big challenge. In this work, a novel functional electrospun nanofiber membrane (PAN@COFs) was synthesized through the in situ growth of covalent organic frameworks (COFs) on a polyacrylonitrile electrospun nanofiber membranes under room temperature and used in the solid-phase micro-extraction (SPME) to enrich trace organochlorine pesticides (OCPs) in water. The resulted PAN@COFs composite consisted of numerous nanofibers coated ample porous COFs spheres (~ 500 nm) and owned stable crystal structure, abundant functional groups, good stability. In addition, the enrichment experiments clearly revealed that PAN@COFs exhibited rather outstanding performance on adsorbing the trace OCPs (as low as 10 ng L-1) with the enrichment of 482-2686 times. Besides, PAN@COFs displayed good reusability and could be reused 100 times. Notably, in the real water samples (sea water and river water), the high enrichment factors and recovery rates strongly confirmed the feasibility of PAN@COFs for detecting the trace OCPs. Furthermore, due to the synergy of π-π stacking interaction and hydrophobic interaction between the OCPs molecules and PAN@COFs, the OCPs could be efficiently adsorbed on PAN@COFs, even under the extremely low driving force.

Lightweight, amphipathic and fire-resistant prGO/MXene spherical beads for rapid elimination of hazardous chemicals.

Frequent leaks of hazardous chemicals have a huge impact on human lives, property and the ecological environment. Therefore, the three-dimensional functional porous materials with high absorption efficiency and special wettability for the disposal of hazardous chemical spills is an urgent demand. In this work, a series of spherical beads consisting of partially reduced graphene oxide (prGO) and MXene (Ti3C2Tx) nanosheets were constructed by hydrogen bond induced self-assembly along with freeze-drying and thermal treatment. The lightweight and amphipathic prGO/MXene spherical beads (prGMSBDs) had millimeter-level size, spherical morphology and highly porous internal structure, which were especially suitable for eliminating hazardous chemicals. Because of their excellent thermal stability and fire retardance, the prGMSBDs could be used to absorb flammable organic liquids, reducing the fire risk of the flammable hazardous chemical spills. Indeed, the prGMSBDs exhibited outstanding absorption performances for various hazardous chemicals, including organic solvents and water-based concentrated acid and alkali. Moreover, the prGMSBDs showed relatively stable absorption performance after five absorption-drying cycles. Due to meeting the requirements of both amphipathic characteristic and flame retardancy, the prGMSBDs reported in this work may offer a promising strategy for rapidly cleaning up various hazardous chemicals and open a feasible route to protecting the combustible hazardous chemical spills from fire.