Evaluation of new compositions of 10% hydrogen peroxide-based bleaching agents containing trimetaphosphate and fluoride on enamel demineralization.

This study evaluated the effect on enamel demineralization of 10% hydrogen peroxide (H2 O2 ) gels containing different concentrations of sodium trimetaphosphate (TMP) and sodium fluoride (NaF) combined with the daily use of fluoridated or placebo dentifrice. Bovine enamel blocks were selected by surface hardness (n = 72) and randomly assigned to one of the following experimental treatments: 10% H2 O2 ; 10% H2 O2  + 3% TMP + 0.1% NaF; and 10% H2 O2  + 0.3% TMP + 0.05% NaF, each with or without fluoridated dentifrice. H2 O2 -based gels were applied for 30 min d-1 followed by treatment with dentifrice (1 min). Enamels blocks were stored in artificial saliva at 37°C between sessions during the 14 days of experiment. Percentage of surface hardness loss (%SH) was calculated, and the blocks were cut into halves to analyze cross-sectional hardness (ΔKHN). Polarized light microscopy images were obtained of the longitudinal sections of the samples. Enamel treated with fluoridated dentifrice presented lower hardness loss than those treated with placebo dentifrice (%SH and ΔKHN). Use of TMP- and NaF-based gels, regardless of concentration, led to the lowest %SH values. Specimens treated with 10% H2 O2 gel had the highest %SH and ΔKHN values. Gels with 10% H2 O2  + 3% TMP + 0.1% NaF showed the lowest ΔKHN values. Microscopy images clearly showed that the addition of TMP and NaF to the H2 O2 -based gels was effective in reducing the loss of hardness, and the fluoridated dentifrice helped minimize it in all treatments.

Effect of long-term water storage on etch-and-rinse and self-etching resin-dentin bond strengths.

This study sought to evaluate the long-term bond strength of etch-and-rinse and self-etch adhesive systems to dentin after one year of water storage. Crown fragments from the buccal surface of extracted bovine incisors were ground flat to expose dentin surfaces. Four etch-and-rinse and two self-etch bonding agents were used according to manufacturers' instructions. Bonded specimens were stored in water for either 24 hours or one year at 37 delete C. After elapsed storage times, specimens were tested for shear bond strength (SBS) at 0.5 mm/min. Data were analyzed by ANOVA and Tukey's tests (p < 0.05). Both evaluated factors (adhesive system and storage time) and their interactions were statistically significant. Single Bond produced the highest SBS regardless of the water degradation period. One-year water storage reduced the SBS of Prime & Bond NT and One-Up Bond F significantly; the other adhesives performed similarly. Long-term bond strengths of etch-and-rinse and self-etch adhesive systems are susceptible to hygroscopic and hydrolytic effects to varying extents, depending on their chemistry and structure. The presence of monomers with different properties might induce preferential degradation of specific adhesive polymer systems.

Characterization of biomodified dentin matrices for potential preventive and reparative therapies.

Biomodification of existing hard tissue structures, specifically tooth dentin, is an innovative approach proposed to improve the biomechanical and biochemical properties of tissue for potential preventive or reparative therapies. The objectives of the study were to systematically characterize dentin matrices biomodified by proanthocyanidin-rich grape seed extract (GSE) and glutaraldehyde (GD). Changes to the biochemistry and biomechanical properties were assessed by several assays to investigate the degree of interaction, biodegradation rates, proteoglycan interaction, and effect of collagen fibril orientation and environmental conditions on the tensile properties. The highest degree of agent-dentin interaction was observed with GSE, which exhibited the highest denaturation temperature, regardless of the agent concentration. Biodegradation rates decreased remarkably following biomodification of dentin matrices after 24h collagenase digestion. A significant decrease in the proteoglycan content of GSE-treated samples was observed using a micro-assay for glycosaminoglycans and histological electron microscopy, while no changes were observed for GD and the control. The tensile strength properties of GD-biomodified dentin matrices were affected by dentin tubule orientation, most likely due to the orientation of the collagen fibrils. Higher and/or increased stability of the tensile properties of GD- and GSE-treated samples were observed following exposure to collagenase and 8 months water storage. Biomodification of dentin matrices using chemical agents not only affects the collagen biochemistry, but also involves interaction with proteoglycans. Tissue biomodifiers interact differently with dentin matrices and may provide the tissue with enhanced preventive and restorative/reparative abilities.

Fluoride-containing adhesive: durability on dentin bonding.

OBJECTIVES: To evaluate (1) the influence of fluoride-containing adhesive on microtensile bond strength (microTBS) and (2) in vitro secondary caries inhibition at the resin-dentin interface after 24 h and 3 months water-storage and (3) the degree of conversion of different adhesives after 24h 1 month. METHODS: Flat surfaces of human teeth were ground and randomly assigned to six groups: (SBMP-24) Scotchbond Multi-Purpose control [SBMP], 24 h; (SE-24) SBMP etch and primer+Clearfil SE Bond adhesive [SE], 24h; (PB-24) SBMP etch and primer+Clearfil Protect Bond adhesive [PB], 24h; (SBMP-3) SBMP, 3 months; (SE-3) SBMP+SE, 3 months; and (PB-3) SBMP+PB, 3 months. To evaluate the effect of the adhesive resin alone, all teeth were etched with 35% phosphoric acid and primed with SBMP primer prior to applying the adhesive resin. Bonded assemblies were prepared for microTBS and stored in distilled water at 37 degrees C for 24h and 3 months. Sections of restored teeth of each group were exposed to an acid challenge. The specimens were sectioned, polished, and then observed with polarized light microscopy (PLM). Also, the degree of conversion (DC) of the adhesives was measured using Fourier Transform-Infrared spectroscopy (FTIR) at 24 h and 1 month, after polymerization. RESULTS: microTBS values obtained in MPa (24h/3m) were: (MP) 61.5+/-10.5/52.9+/-8.9, (SE) 55.5+/-11.8/55.6+/-13, and (PB) 50.3+/-9.9/61.0+/-13.6. For interface analysis by PLM, an inhibition zone (IZ) adjacent to the hybrid layer was created only when the fluoride-containing adhesive (PB) was used. The DC in percentage (24 h, 1 month) were: (MP) 60.5+/-2.8/61.3+/-0.6, (SE) 69.6+/-1.3/70.7+/-0.05, and (PB) 53.1+/-0.4/58.3+/-1.6. SIGNIFICANCE: The fluoride-containing adhesive demonstrated significant increase of bond strength values after water-storage. This material was also able to create an acid inhibition zone in dentin. There was a significant increase of degree of conversion after 1 month only for PB.