Achievable pin spanning angulation in anterosuperior pelvic external fixation.

INTRODUCTION: Pelvic external fixation using anterosuperior pins provides a quick method of stabilization without necessitating fluoroscopic guidance. Various locations, depths, and inclinations have been cited for external fixator pins; however, the existing literature lacks clear indications for the angular difference between pins. Thus, we aimed to determine the greatest degree of sagittal pin spanning angulation (SPSA) between two iliac crest pins and how intraosseous depth (ID) affects these angulations. MATERIALS AND METHODS: A newly developed computer algorithm produced cross sections of 3D pelvic reconstructions in the sagittal plane in 5° increments. Computer-generated pins with IDs of 60, 75, and 90 mm were positioned in 5° increments transversely. Pins were assessed for cortical containment to define values for SPSA and transverse pin spanning angulation (TPSA). RESULTS: A bimodal distribution revealed varying degrees of insertion frequency and SPSA, cranially and caudally. The caudal distribution exhibited greater cortical containment with larger values for SPSA and TPSA. The highest insertion frequency (85.7%) and largest SPSA (155°) were observed for the 60-mm ID. Increasing ID resulted in further bony penetration and smaller values for SPSA and TPSA. CONCLUSIONS: Expanding the degree of SPSA between inserted pins in anterosuperior pelvic external fixation can be challenging due to the thinning of the iliac wing, which affords a narrow corridor for intraosseous pin containment. An ID of 60 mm allows larger degrees of SPSA while maintaining higher rates of cortical pin containment when compared to pins with greater IDs.

Segmental acetabular rim defects, bone loss, oversizing, and press fit cup in total hip arthroplasty evaluated with a probabilistic finite element analysis.

PURPOSE: Management of segmental rim defects and bone mineral density (BMD) loss in the elderly prior to total hip replacement is unclear within classification systems for acetabular bone loss. In this study, our objectives were (1) to understand how a reduction in BMD in the elderly affects the oversizing of a press-fit cup for primary fixation and (2) to evaluate whether the location of the segmental defect affected cup fixation. METHODS: A finite element (FE) model was used to simulate and evaluate cup insertion and fixation in the context of segmental rim defects. We focused on the distribution of patients over age 70 and used BMD (estimated from CT) as a proxy for aging's implications on THR and used probabilistic FE analysis to understand how BMD loss affects oversizing of a press-fit cup. RESULTS: A cup oversized by 1.10 ± 0.28 mm provides sufficient fixation and lower stresses at the cup-bone interface for elderly patients. Defects in the anterior column and posterior column both required the same mean insertion force for cup seating of 84% (taken as an average of 2 anterior column and 2 posterior column defects) compared to the control configuration, which was 5% greater than the insertion force for a superior rim defect and 12% greater than the insertion force for an inferior rim defect. CONCLUSIONS: A defect along the superior or inferior rim had a minimal effect on cup fixation, while a defect in the columns created cup instability and increased stress at the defect location.

Biomechanical evaluation of distal biceps tendon repair using tension slide technique and knotless fixation technique.

BACKGROUND: Acute distal biceps tendon ruptures are uncommon injuries that often affect young active males, typically resulting from an eccentric load on their dominant extremity. The purpose of this study was to compare pullout strength and tendon gapping in the tension slide technique (TST) versus a knotless fixation technique (KFT). METHODS: Two sets of experiments were performed using cadaveric elbow specimens. In the first experiment, eight elbows from different cadavers were tested to compare TST with a standard locking whipstitch with KFT, four elbows in each group, using a standard locking whipstitch. In the second experiment, 12 elbows were used to study the differences between TST with a standard locking whipstitch with KFT using suture tape reinforced whipstitch (RKFT), using the TST data from the first and second experiment. Each experiment evaluated gapping after cyclic loading and the second experiment also tested the construct to load to failure. RESULTS: Gapping for KFT with a standard locking whipstitch was 10.64 mm versus 2.69 mm for the TST after 1000 cycles (P = 0.016). A reinforced whipstitch significantly improved the failure to gap on the KFT with no significant difference in gapping when compared to TST after 3000 cycles (P = 0.36). The resultant gapping for TST and KST was 2.08 mm and 2.99 mm (P = 0.91), respectively. Load to failure for TST and KFT were 282 Nm and 328 Nm (P = 0.20), respectively. CONCLUSION: Bone-tendon gap resistance of a KFT repair of a torn distal biceps tendon is limited by suture technique. Using a tape reinforced locking whipstitch, the repair is as strong as TST repair. LEVELS OF EVIDENCE: Basic Science.

Validating a Modified Circle Theorem Method for the Measurement of Acetabular Cup Anteversion on Plain Radiography with Intra-Operative Data from Robotic Assisted Total Hip Arthroplasty.

This study aims to validate a modified circle theorem method for the calculation of true version of the acetabular component on anteroposterior x-rays with intra-operative version data derived from robotic assisted total hip arthroplasty (THA). Planar anteversion measurements recorded intraoperatively in 80 THAs were correlated to measurements on anteroposterior radiographs. The mean anteversion of the cohort measured by the robotic system and on plain radiography was 21.2° ± 2.0° and 19.9° ± 3.4° respectively and 97.5% of cases were in a 30% relative error. The correlation between the true and planar measurements of anteversion on plain radiographs was strong (Pearson correlation coefficient of 0.9422). We conclude that the circle theorem method can be validated with data from robotic guided THA.

Biomechanical Comparison of Perpendicular Versus Oblique In Situ Screw Fixation of Slipped Capital Femoral Epiphysis.

BACKGROUND: Percutaneous in situ single screw fixation is the preferred treatment for stable and unstable slipped capital femoral epiphysis (SCFE). The recommended screw placement is in the center of the epiphysis and perpendicular to the physis, which necessitates an anterior starting point for most SCFEs. A recent clinical study has shown good clinical results with a laterally based screw for SCFE, which is oblique to the physis. We sought to biomechanically compare these 2 techniques for load to failure and hypothesized that the laterally based oblique screw is equivalent or superior to an anteriorly based perpendicular screw. METHODS: Twenty-two paired immature porcine femurs were used to compare the techniques. A SCFE model was created in all femurs using a previously published technique by performing a 30-degree posterior closing wedge osteotomy through the proximal physis. In the control group, a screw was placed perpendicular to the slip with an anterior starting point. In the experimental group, the screw was started as close to the mid-lateral cortex of the proximal femur as possible while maintaining the screw anterior to the posterior cortex of the femoral neck and ending at the apex of the epiphysis ignoring the resultant angle to the physis for the experimental group. The specimens were then potted and loaded in a physiologically relevant posteroinferior direction (30 degrees posterior from vertical) to determine load to failure (N) and stiffness (N/mm). RESULTS: No statistical difference was found between the 2 groups in maximum load to failure or stiffness (P>0.05). CONCLUSIONS: A laterally based screw oblique to the physis for in situ fixation in mild SCFE is not significantly different than an anteriorly based screw perpendicular to the physis in load to failure and stiffness in our study model. CLINICAL RELEVANCE: In light of no difference in load to failure of these 2 constructs, surgeons may be more comfortable with the traditional lateral entry point while still aiming for screw placement in the center of head.

Biomechanical Comparison of All-Suture, All-Inside Meniscus Repair Devices in a Human Cadaveric Meniscus Model.

OBJECTIVE: Newer all-suture, all-inside meniscus repair devices utilize soft suture anchors. The purpose of this study was to compare the biomechanical performance of 4 meniscus repair devices in human cadaver menisci: the JuggerStitch (all-suture, all-inside), the FiberStitch (all-suture, all-inside), a polyether ether ketone (PEEK) all-inside, and an inside-out device. DESIGN: Forty human cadaver menisci were tested after creating 20 mm longitudinal tears in the posterior meniscus. Each knee was randomized to 1 of 4 meniscus repair groups: JuggerStitch (all-suture, all-inside), FiberStitch (all-suture, all-inside), FAST-FIX 360 (PEEK-based anchor all-inside), and inside-out (with BroadbandTM tape meniscus needles). For each meniscus, 2 devices were used to prepare vertical mattress repair construct. The specimens were tested by pre-conditioning 20 cycles between 5 N and 30 N and then the tear diastasis was measured, followed by distraction to failure phase after imposing a displacement at a rate of 0.5 mm/s. RESULTS: Ten menisci were tested in each of the 4 groups. After pre-conditioning, there was no significant difference in the gap formation among groups (P = 0.212). The average failure load for the JuggerStitch, FiberStitch, PEEK all-inside, and inside-out was 384 N, 311 N, 207 N, and 261 N, respectively, with a significant difference between groups (P = 0.034). Post hoc analysis showed the JuggerStitch failure load was higher than the PEEK all-inside and inside-out (P = 0.005, and P = 0.045, respectively). There was no significant difference between the failure load of the JuggerStitch and FiberStitch (P = 0.225). CONCLUSION: The JuggerStitch all-suture device, FiberStitch all-suture device, PEEK all-inside, and inside-out devices have similar biomechanical properties for gapping and stiffness. The JuggerStitch all-suture, all-inside device has superior failure load compared with the PEEK all-inside and inside-out repair for longitudinal meniscus tear repair.

The Joystick Method: A Mini Open Technique for Repairing Patellar Osteochondral Fractures With Concomitant Medial Patellofemoral Ligament Reconstruction.

Fixation of osteochondral fractures after patellar dislocation is typically done using an open approach due to the location of the defect. This is traditionally performed through a medial parapatellar arthrotomy to allow adequate visualization. By using the joystick method, adequate visualization is achieved with a smaller arthrotomy. Careful placement of the joystick in the planned anchor site of the medial patellofemoral ligament reconstruction reduces the number of drill sites in the patella.

Suture Tying Force for Cut-Out during Radial Meniscus Tear Repair: A Biomechanical Evaluation of Failure Loads during the Knot-Tying Process.

OBJECTIVE: The purpose of the study was to determine average tensile forces resulting in suture failure while tying a knot during repair of complete radial meniscus tears and to compare the failure tensile force based on meniscus tissue location: the peripheral (red-red) versus inner (white-white). DESIGN: This study was designed as a cadaveric biomechanical study using 24 menisci harvested from fresh frozen cadaveric knees with midbody radial tears. Tears were repaired using 2-0 nonabsorbable suture in both the inner meniscus and the peripheral meniscus. A force gauge was used to measure the tension of a surgeon's knot until failure of either the suture or the meniscus tissue. Statistical analysis was performed comparing suture failure tensile forces between inner and peripheral sutures using 2-sample t test. RESULTS: Suture repairs primarily failed due to meniscal tissue cut-out after suture tensioning (96%). There was no statistical difference in failure mode between medial and lateral meniscus for both the inner (100% cut-out) and the peripheral (92% cut-out; P = 0.703) sutures. The peripheral sutures failed as significantly higher loads (54 ± 26 N) than the inner sutures (36 ± 11 N, P = 0.006). The peripheral meniscus tissue tolerated significantly higher tension at failure (36 ± 7 N) than the inner meniscus (26 ± 7 N, P < 0.001). CONCLUSION: When tying parallel sutures to repair a radial meniscus tear, suture tensile forces above 30 N may tear through meniscus tissue. Surgeons should not use suture tying forces above 30 N when repairing radial meniscus tears with parallel sutures. The peripheral meniscus can withstand higher knot-tying forces than the inner meniscus, so surgeons should consider tying the peripheral suture before the inner suture.

Enhanced Manual Ventilation with a Handheld Audiovisual Device - BENGI - Insights from a Pilot Study in Special Operations Medicine.

BACKGROUND: In emergency casualty and evacuation situations, manual ventilation using self-inflating bags remains a critical skill; however, significant challenges exist in ensuring safety and effectiveness, since inaccurate manual ventilation is associated with life-threatening risks (e.g., gastric insufflation with aspiration, barotrauma, and reduced venous return). METHODS: This study assessed the impact of audiovisual feedback from the bag-valve-mask (BVM) emergency narration guided instrument (BENGI), a handheld manual ventilation guidance device, on improving performance and safety, immediately and 2 weeks after, with no additional manual ventilation training. In a crossover manikin simulation study with 20 participants, BENGI immediately and significantly improved tidal volume and respiratory rate accuracy. RESULTS: Intraand inter-participant variations were lower with BENGI, with Poincaré plot analysis showing improved performance that remained for at least 2 weeks following BENGI training. CONCLUSION: BENGI's audiovisual feedback improves manual immediately and persistently, making it invaluable for training and clinical use in diverse scenarios, from battlespace to civilian emergencies.

Effects of A2 Pulley Venting on Bowstringing and Tendon Slack: A Biomechanical Investigation.

BACKGROUND: A2 pulley release is often needed for exposure of the lacerated tendon, retrieval of retracted tendons, placement of core sutures, or to permit full motion and gliding of the repaired and edematous tendon. However, there is no agreement in the literature on the specific quantity of pulley venting that can be performed and recommendations are limited to an undefined "judicious release" of the pulleys when necessary. METHODS: Following a previously developed testing protocols, finger kinematics, tendon excursion, and bowstringing were evaluated on cadaveric hands for venting in increments of 20% of the pulley length. RESULTS: In our study, we found a statistically significant influence of venting on bowstringing, although no difference was found between fingers, and a significant difference in tendon slack, which was variable depending on the finger. Bowstringing started increasing at 20% of A2 venting and peaked at full release. Tendon slack did not start until 40% of A2 venting on the index finger, but started at 20% on the middle, ring, and small fingers. CONCLUSIONS: Venting of the A2 pulley leads to an incremental increase in tendon bowstringing and tendon slack. However, differences in metacarpophalangeal flexion angle were not observed until full A2 pulley release, and only observed in the index finger, and no differences were observed in proximal interphalangeal flexion angles. Therefore, the benefit of releasing the A2 pulley when clinically necessary will likely outweigh the risks of loss of motion or strength.

Impact of bone density and integrated screw configuration on standalone anterior lumbar interbody construct strength.

Background: In anterior lumbar interbody fusion (ALIF), the use of integrated screws is attractive to surgeons because of the ease of implantation and no additional profile. However, the number and length of screws necessary for safe and stable implantation in various bone densities is not yet fully understood. The current study aims to determine how important both length and number of screws are for stability of ALIFs. Methods: Three bone models with densities of 10, 15, and 20 pounds per cubic foot (PCF) were chosen as surrogates. These were instrumented using the Z-Link lumbar interbody system with either 2, 3, or 4 integrated 4.5 × 20 mm screws or 4.5 × 25 mm screws (Zavation, LLC, Flowood, MS). The bone surrogates were tested with loading conditions resulting in spine extension to measure construct stiffness and peak force. Results: The failure load of the construct was influenced by the length of screws (p=.01) and density of the bone surrogate (p<.01). There was no difference in failure load between using 2 screws and 3 screws (p=.32) or when using four 20 mm screws versus three 25 mm screws (p=.295). Conclusion: In our study, both bone density and length of screws significantly affected the construct's load to failure. In certain cases where a greater number of screws are unable to be implanted, the same stability can potentially be conferred with use of longer screws. Future clinical studies should be performed to test these biomechanical results.

In Vitro Evaluation of Lateral Femur Condyle Free Chondral Fragment Swelling after Soaking in Normal Saline.

OBJECTIVE: After traumatic knee injuries, chondral fragments can avulse off bone with the progeny fragment becoming a loose body. The loose fragment may be larger than expected when trying to surgically repair the fragment back to its original site. The purpose of this study was to determine whether a loose chondral fragment from the lateral femur condyle would increase in size and weight after soaking in normal saline (NS) for 14 days. DESIGN: Twelve 6-mm OAT (osteoarticular transfer) plugs were harvested from 6 cadaver knees on the lateral femoral condyle to simulate a chondral fragment. The chondral fragments were then placed inside an airtight specimen container with NS (0.9% sodium chloride) and were measured over 14 days. RESULTS: After 14 days, the chondral fragments showed no increase in diameter as they measured an average of 5.567 ± 0.448 mm on Day 1 and 5.702 ± 0.253 mm on Day 14 (P = 0.183). The chondral fragments showed an increase in mass from an average of 0.058 ± 0.012 g on Day 1 to 0.073 ± 0.012 g on Day 14 (P < 0.001) and an increase in thickness from an average of 2.038 ± 0.346 mm on Day 1 to 2.229 ± 0.297 mm on Day 14 (P = 0.033). CONCLUSIONS: Chondral fragments in NS increase in mass and thickness over time, but do not change in diameter. When surgeons are evaluating loose chondral fragments for fixation, they should consider that these fragments may appear thicker than the recipient location.

Compressibility of Osteochondral Autograft Transfer Donor Grafts: A Comparison of Different Donor Regions and How Much Shortening Occurs of Plugs After Impaction.

Background: Osteochondral autograft transfer (OAT) is a useful technique for full-thickness cartilage lesions of the distal femur. Various techniques recommend harvesting a plug 2 mm longer than the recipient hole to allow for graft impaction. Grafts with limited compressibility may not sit flush when impacted. Purpose: To compare the compressibility/shortening of OAT donor plug regions from the distal femur of human cadaveric knees after impaction. Study Design: Controlled laboratory study. Methods: A total of 20 cadaveric knees (mean age, 70.3 ± 8.4 years) were divided into 4 donor regions: medial intercondylar (IC) notch, lateral IC notch, medial trochlea, and lateral trochlea. Each region was subdivided into 4 zones: far superior (FSZ), middle superior (MSZ), middle inferior (MIZ), and far inferior (FIZ). A total of 320 grafts (6-mm diameter, 15-mm depth) were extracted, and a custom-built machine was used to strike the graft 5 times using a predetermined energy of 0.11 J. The graft length was measured initially and after each impact. Statistical analysis of the compressibility for each of the 4 regions and all 16 zones was performed utilizing analysis of variance, with post hoc testing using the Fisher's least significant difference. Results: Compression in the lateral IC notch, medial IC notch, medial trochlea, and lateral trochlea was 2.4 ± 1.5, 2.1 ± 0.7, 3.1 ± 2.2, and 2.1 ± 0.6 mm, respectively, with significant differences between the 4 regions (P < .01) and the most compression in the medial trochlea (P < .01). Subgroup analysis showed that the lateral trochlea had higher compressibility for FIZ versus MIZ (P = .02) and the lateral IC notch had higher compressibility for FSZ versus FIZ and MIZ (P < .05 for both). Conclusion: Compressibility varied between OAT donor sites in the distal femur. OAT donor grafts showed the highest compressibility in the medial trochlea (3.1 mm) and lateral IC notch FSZ (3.0 mm). Clinical Relevance: The lateral trochlea, medial IC notch, and the lower zones of the lateral IC notch grafts should not be oversized more than 2 mm in length, as these grafts may not compress adequately.

Acetabular Wall Weakening in Total Hip Arthroplasty: A Pilot Study.

Total hip arthroplasty is a widely performed operation allowing disabled patients to improve their quality of life to a degree greater than any other elective procedure. Planning for a THA requires adequate patient assessment and preoperative characterizations of acetabular bone loss via radiographs and specific classification schemes. Some surgeons may be inclined to ream at a larger diameter thinking it would lead to a more stable press-fit, but this could be detrimental to the acetabular wall, leading to intraoperative fracture. In the attempt to reduce the incidence of intraoperative fractures, the current study aims to identify how increased reaming diameter degrades and weakens the acetabular rim strength. We hypothesized that there is proportionality between the reaming diameter and the reduction in acetabular strength. To test this hypothesis, this study used bone surrogates, templated from CT scans, and reamed at different diameters. The obtained bone surrogate models were then tested using an Intron 8874 mechanical testing machine (Instron, Norwood, MA) equipped with a custom-made fixture. Analysis of variance (ANOVA) was used to identify differences among reamed diameters while linear regression was used to identify the relationship between reamed diameters and acetabular strength. We found a moderate correlation between increasing reaming diameter that induced thinning of the acetabular wall and radial load damage. For the simplified acetabular model used in this study, it supported our hypothesis and is a promising first attempt in providing quantitative data for acetabular weakening induced by reaming.

Experimental validation of a portable tidal volume indicator for bag valve mask ventilation.

INTRODUCTION: Short-term emergency ventilation is most typically accomplished through bag valve mask (BVM) techniques. BVMs like the AMBU® bag are cost-effective and highly portable but are also highly prone to user error, especially in high-stress emergent situations. Inaccurate and inappropriate ventilation has the potential to inflict great injury to patients through hyper- and hypoventilation. Here, we present the BVM Emergency Narration-Guided Instrument (BENGI) - a tidal volume feedback monitoring device that provides instantaneous visual and audio feedback on delivered tidal volumes, respiratory rates, and inspiratory/expiratory times. Providing feedback on the depth and regularity of respirations enables providers to deliver more consistent and accurate tidal volumes and rates. We describe the design, assembly, and validation of the BENGI as a practical tool to reduce manual ventilation-induced lung injury. METHODS: The prototype BENGI was assembled with custom 3D-printed housing and commercially available electronic components. A mass flow sensor in the central channel of the device measures air flow, which is used to calculate tidal volume. Tidal volumes are displayed via an LED ring affixed to the top of the BENGI. Additional feedback is provided through a speaker in the device. Central processing is accomplished through an Arduino microcontroller. Validation of the BENGI was accomplished using benchtop simulation with a clinical ventilator, BVM, and manikin test lung. Known respiratory quantities were delivered by the ventilator which were then compared to measurements from the BENGI to validate the accuracy of flow measurements, tidal volume calculations, and audio cue triggers. RESULTS: BENGI tidal volume measurements were found to lie within 4% of true delivered tidal volume values (95% CI of 0.53 to 3.7%) when breaths were delivered with 1-s inspiratory times, with similar performance for breaths delivered with 0.5-s inspiratory times (95% CI of 1.1 to 6.7%) and 2-s inspiratory times (95% CI of -1.1 to 2.3%). Audio cues "Bag faster" (1.84 to 2.03 s), "Bag slower" (0.35 to 0.41 s), and "Leak detected" (43 to 50%) were triggered close to target trigger values (2.00 s, 0.50 s, and 50%, respectively) across varying tidal volumes. CONCLUSIONS: The BENGI achieved its proposed goals of accurately measuring and reporting tidal volumes delivered through BVM systems, providing immediate feedback on the quality of respiratory performance through audio and visual cues. The BENGI has the potential to reduce manual ventilation-induced lung injury and improve patient outcomes by providing accurate feedback on ventilatory parameters.

Efficacy and safety testing of a COVID-19 era emergency ventilator in a healthy rabbit lung model.

BACKGROUND: The COVID-19 pandemic revealed a substantial and unmet need for low-cost, easily accessible mechanical ventilation strategies for use in medical resource-challenged areas. Internationally, several groups developed non-conventional COVID-19 era emergency ventilator strategies as a stopgap measure when conventional ventilators were unavailable. Here, we compared our FALCON emergency ventilator in a rabbit model and compared its safety and functionality to conventional mechanical ventilation. METHODS: New Zealand white rabbits (n = 5) received mechanical ventilation from both the FALCON and a conventional mechanical ventilator (Engström Carestation™) for 1 h each. Airflow and pressure, blood O2 saturation, end tidal CO2, and arterial blood gas measurements were measured. Additionally, gross and histological lung samples were compared to spontaneously breathing rabbits (n = 3) to assess signs of ventilator induced lung injury. RESULTS: All rabbits were successfully ventilated with the FALCON. At identical ventilator settings, tidal volumes, pressures, and respiratory rates were similar between both ventilators, but the inspiratory to expiratory ratio was lower using the FALCON. End tidal CO2 was significantly higher on the FALCON, and arterial blood gas measurements demonstrated lower arterial partial pressure of O2 at 30 min and higher arterial partial pressure of CO2 at 30 and 60 min using the FALCON. However, when ventilated at higher respiratory rates, we observed a stepwise decrease in end tidal CO2. Poincaré plot analysis demonstrated small but significant increases in short-term and long-term variation of peak inspiratory pressure generation from the FALCON. Wet to dry lung weight and lung injury scoring between the mechanically ventilated and spontaneously breathing rabbits were similar. CONCLUSIONS: Although conventional ventilators are always preferable outside of emergency use, the FALCON ventilator safely and effectively ventilated healthy rabbits without lung injury. Emergency ventilation using accessible and inexpensive strategies like the FALCON may be useful for communities with low access to medical resources and as a backup form of emergency ventilation.

Characterization of regional variation of bone mineral density in the geriatric human cervical spine by quantitative computed tomography.

BACKGROUND: Odontoid process fractures are among the most common in elderly cervical spines. Their treatment often requires fixation, which may include use of implants anteriorly or posteriorly. Bone density can significantly affect the outcomes of these procedures. Currently, little is known about bone mineral density (BMD) distributions within cervical spine in elderly. This study documented BMD distribution across various anatomical regions of elderly cervical vertebrae. METHODS AND FINDINGS: Twenty-three human cadaveric C1-C5 spine segments (14 males and 9 female, 74±9.3 y.o.) were imaged via quantitative CT-scan. Using an established experimental protocol, the three-dimensional shapes of the vertebrae were reconstructed from CT images and partitioned in bone regions (4 regions for C1, 14 regions for C2 and 12 regions for C3-5). The BMD was calculated from the Hounsfield units via calibration phantom. For each vertebral level, effects of gender and anatomical bone region on BMD distribution were investigated via pertinent statistical tools. Data trends suggested that BMD was higher in female vertebrae when compared to male ones. In C1, the highest BMD was found in the posterior portion of the bone. In C2, BMD at the dens was the highest, followed by lamina and spinous process, and the posterior aspect of the vertebral body. In C3-5, lateral masses, lamina, and spinous processes were characterized by the largest values of BMD, followed by the posterior vertebral body. CONCLUSIONS: The higher BMD values characterizing the posterior aspects of vertebrae suggest that, in the elderly, posterior surgical approaches may offer a better fixation quality.

Medial Transmalleolar Portal Technique for Ankle Arthroscopic Headless Screw Fixation of Talar Osteochondritis Dissecans Lesions.

This article describes a technique for arthroscopic fixation of an osteochondritis dissecans (OCD) lesion of the medial talar dome with headless compression screws. This technique involves creation of a medial transmalleolar portal using a guide and drill. The medial transmalleolar portal grants perpendicular access for screw fixation of OCD lesions in addition to the potential for osteochondral autograft transplantation (OAT). Advantages include access to the medial talar dome without performing a medial malleolar osteotomy. After completion of OCD fixation, an inverted osteochondral plug can be used to backfill the portal.

Variability in rod to bone distance needed in pelvic subcutaneous internal fixation to avoid nerve compression: A tridimensional population-based study.

INTRODUCTION: Pelvic internal fixation has become a popular method for treatment of unstable pelvic ring injuries. Although successful, one complication is femoral nerve palsy from compression of the connecting rod. In light of this complication, this study was designed to evaluate sagittal inclinations of the rod and the feasibility of using a rod with a constant curvature. HYPOTHESIS: It is hypothesized that that there is a connection between the sagittal inclination of the rod and the rod to bone distance, as well as single rod can be contoured with a constant curvature to be used in the majority of all patients. METHODS: Three dimensional models of pelvis CTs from a single level 1 trauma center were created and imported into a program where software superimposed a pre-contoured rod in the sagittal planes upon the pelvic slices. The sagittal inclination was deemed acceptable is no interference occurred between the area of compression risk and the rod. For each pelvis and considered sagittal rod inclination, the rod radius of curvature (ROC), minimal rod to bone distance (RTB) and transverse inclinations (φL and φR) were measured at which the pedicle screws should be inserted to follow the direction of the smallest RTB. RESULTS: The sagittal inclinations feasible for all subjects were between 15° to 30°. In this sagittal range, the average RTB varied in values ranging from 4.0±0.9mm to 25.4±11.4mm (p<0.01). Only 46% of subjects allowed a rod with constant curvature. DISCUSSION AND CONCLUSION: Our study found that a rod to bone distance of 15mm was not safe for all models. As well, many subject models did not allow placement of pre-contoured rod. Patient specific templating of pelvic subcutaneous internal fixation is strictly needed to limit complications. LEVEL OF EVIDENCE: VII; Basic Science.

Salvaging Pull-Out Strength in a Previously Stripped Screw Site: A Comparison of Three Rescue Techniques.

Screw stripping during bone fixation is a common occurrence during operations that results in decreased holding capacity and bone healing. We aimed to evaluate the rescue of the stripped screw site using screws of different dimensions. Five screw configurations were tested on cadaveric specimens for pull-out strength (POS). The configurations included a control screw tightened without stripping, a configuration voluntarily stripped and left in place, and three more configurations in which the stripped screws were replaced by a different screw with either increased overall length, diameter, or thread length. Each configuration was tested five times, with each screw tested once. The POS of the control screw, measured to be 153.6 ± 27 N, was higher than the POS measured after stripping and leaving the screw in place (57.1 ± 18 N, p = 0.001). The replacement of the stripped screw resulted in a POS of 158.4 ± 64 N for the screw of larger diameter, while the screws of the same diameter but increased length or those with extended thread length yielded POS values of 138.4 ± 42 and 185.7 ± 48 N, respectively. Screw stripping is a frequent intraoperative complication that, according to our findings, cannot be addressed by leaving the screw in place. The holding capacity of a stripped screw implanted in cancellous bone can successfully be restored with a different screw of either larger diameter, longer length, or extended thread length.