High Hole Mobility and Nonsaturating Giant Magnetoresistance in the New 2D Metal NaCu4Se4 Synthesized by a Unique Pathway.

The new compound NaCu4Se4 forms by the reaction of CuO and Cu in a molten sodium polyselenide flux, with the existence of CuO being unexpectedly critical to its synthesis. It adopts a layered hexagonal structure (space group P63/ mmc with cell parameters a = 3.9931(6) Å and c = 25.167(5) Å), consisting of infinite two-dimensional [Cu4Se4]- slabs separated by Na+ cations. X-ray photoelectron spectroscopy suggests that NaCu4Se4 is mixed-valent with the formula (Na+)(Cu+)4(Se2-)(Se-)(Se2)2-. NaCu4Se4 is a p-type metal with a carrier density of ∼1021 cm-3 and a high hole mobility of ∼808 cm2 V-1 s-1 at 2 K based on electronic transport measurements. First-principles calculations suggest the density of states around the Fermi level are composed of Cu-d and Se-p orbitals. At 2 K, a very large transverse magnetoresistance of ∼1400% was observed, with a nonsaturating, linear dependence on field up to 9 T. Our results indicate that the use of metal oxide chemical precursors can open reaction paths to new low-dimensional compounds.

In Situ Synthesis of Highly Dispersed and Ultrafine Metal Nanoparticles from Chalcogels.

We report a unique reaction type for facile synthesis of ultrafine and well-dispersed Pt nanoparticles supported on chalcogel surfaces. The nanoparticles are obtained by in situ Pt2+ reduction of a chalcogel network formed by the metathesis reaction between K2PtCl4 and Na4SnS4. The rapid catalytic ability of the chalcogel-supported Pt nanoparticles is demonstrated in a recyclable manner by using 4-nitrophenol reduction as a probe reaction.

Highly Efficient Separation of Trivalent Minor Actinides by a Layered Metal Sulfide (KInSn2S6) from Acidic Radioactive Waste.

The elimination of trivalent minor actinides (Am3+, Cm3+) is of great concern for the safe management and operation of nuclear waste geological repository and environmental remediation. However, because of the effects of protonation, most of the present sorbents exhibit inferior removal properties toward minor actinides at low pH values. Finding stable ion-exchangers with high sorption capacities, fast kinetics, and good removal toward minor actinides from highly acidic solution remains a great challenge. This work reports a new family member of KMS materials with a robust acid-stable layered metal sulfide structure (KInSn2S6, KMS-5) bearing strong affinity toward trivalent minor actinides. KMS-5 can simultaneously separate trivalent 241Am and 152Eu from acidic solutions below pH 2 with high efficiency (>98%). The ion-exchange kinetics is extremely fast (<10 min) and the largest distribution coefficient is as high as 5.91 × 104 mL/g. KMS-5 is also capable of efficiently removing 241Am from acidic solution containing various competitive cations in large excess. In addition, the ion exchange process of 241Am by KMS-5 is reversible and the loaded material can be easily eluted by high concentration of potassium chloride. This work represents the first case for efficient minor actinides removal from highly acidic solution using layered metal sulfide materials.

Importance of Reducing Vapor Atmosphere in the Fabrication of Tin-Based Perovskite Solar Cells.

Tin-based halide perovskite materials have been successfully employed in lead-free perovskite solar cells, but the tendency of these materials to form leakage pathways from p-type defect states, mainly Sn4+ and Sn vacancies, causes poor device reproducibility and limits the overall power conversion efficiencies (PCEs). Here, we present an effective process that involves a reducing vapor atmosphere during the preparation of Sn-based halide perovskite solar cells to solve this problem, using MASnI3, CsSnI3, and CsSnBr3 as the representative absorbers. This process enables the fabrication of remarkably improved solar cells with PCEs of 3.89%, 1.83%, and 3.04% for MASnI3, CsSnI3, and CsSnBr3, respectively. The reducing vapor atmosphere process results in more than 20% reduction of Sn4+/Sn2+ ratios, which leads to greatly suppressed carrier recombination, to a level comparable to their lead-based counterparts. These results mark an important step toward a deeper understanding of the intrinsic Sn-based halide perovskite materials, paving the way to the realization of low-cost and lead-free Sn-based halide perovskite solar cells.

Copper Ion Binding Site in ß-Amyloid Peptide.

ß-Amyloid aggregates in the brain play critical roles in Alzheimer's disease, a chronic neurodegenerative condition. Amyloid-associated metal ions, particularly zinc and copper ions, have been implicated in disease pathogenesis. Despite the importance of such ions, the binding sites on the ß-amyloid peptide remain poorly understood. In this study, we use scanning tunneling microscopy, circular dichroism, and surface-enhanced Raman spectroscopy to probe the interactions between Cu2+ ions and a key ß-amyloid peptide fragment, consisting of the first 16 amino acids, and define the copper-peptide binding site. We observe that in the presence of Cu2+, this peptide fragment forms ß-sheets, not seen without the metal ion. By imaging with scanning tunneling microscopy, we are able to identify the binding site, which involves two histidine residues, His13 and His14. We conclude that the binding of copper to these residues creates an interstrand histidine brace, which enables the formation of ß-sheets.

Hexagons to Ribbons: Flipping Cyanide on Au{111}.

Cyanide monolayers on Au{111} restructure from a hexagonal close-packed lattice to a mixed-orientation "ribbon" structure through thermal annealing. The new surface structure loses most of the observed surface features characterizing the initial as-adsorbed system with "ribbon" domain boundaries isolating rotationally offset surface regions where the orientation is guided by the underlying gold lattice. A blue shift to higher frequencies of the CN vibration to 2235 cm-1 with respect to the as-adsorbed CN/Au{111} vibration at 2146 cm-1 is observed. In addition, a new low-frequency mode is observed at 145 cm-1, suggesting a chemical environment change similar to gold-cyanide crystallization. We discuss this new structure with respect to a mixed cyanide/isocyanide monolayer and propose a bonding scheme consisting of Au-CN and Au-NC bound molecules that are oriented normal to the Au{111} surface.

Integrated perovskite/bulk-heterojunction toward efficient solar cells.

We successfully demonstrated an integrated perovskite/bulk-heterojunction (BHJ) photovoltaic device for efficient light harvesting and energy conversion. Our device efficiently integrated two photovoltaic layers, namely a perovskite film and organic BHJ film, into the device. The device structure is ITO/TiO2/perovskite/BHJ/MoO3/Ag. A wide bandgap small molecule DOR3T-TBDT was used as donor in the BHJ film, and a power conversion efficiency (PCE) of 14.3% was achieved in the integrated device with a high short circuit current density (JSC) of 21.2 mA cm(-2). The higher JSC as compared to that of the traditional perovskite/HTL (hole transporting layer) device (19.3 mA cm(-2)) indicates that the BHJ film absorbs light and contributes to the current density of the device. Our result further suggests that the HTL in traditional perovskite solar cell, even with good light absorption capability, cannot contribute to the overall device photocurrent, unless this HTL becomes a BHJ layer (by adding electron transporting material like PC71BM).

Differences in the Toxicological Potential of 2D versus Aggregated Molybdenum Disulfide in the Lung.

2D molybdenum disulfide (MoS2 ) has distinct optical and electronic properties compared to aggregated MoS2 , enabling wide use of these materials for electronic and biomedical applications. However, the hazard potential of MoS2 has not been studied extensively. Here, a comprehensive analysis of the pulmonary hazard potential of three aqueous suspended forms of MoS2 -aggregated MoS2 (Agg-MoS2 ), MoS2 exfoliated by lithiation (Lit-MoS2 ), and MoS2 dispersed by Pluronic F87 (PF87-MoS2 )-is presented. No cytotoxicity is detected in THP-1 and BEAS-2B cell lines. However, Agg-MoS2 induces strong proinflammatory and profibrogenic responses in vitro. In contrast, Lit- and PF87-MoS2 have little or no effect. In an acute toxicity study in mice, Agg-MoS2 induces acute lung inflammation, while Lit-MoS2 and PF87-MoS2 have little or no effect. In a subchronic study, there is no evidence of pulmonary fibrosis in response to all forms of MoS2 . These data suggest that exfoliation attenuates the toxicity of Agg-MoS2 , which is an important consideration toward the safety evaluation and use of nanoscale MoS2 materials for industrial and biological applications.

The identification and characterization of defect states in hybrid organic-inorganic perovskite photovoltaics.

Thin film photovoltaic cells based on hybrid halide perovskite absorbers have emerged as promising candidates for next generation photovoltaics. Here, we have characterized and identified the defect energy distribution in the CH3NH3PbI3 perovskite using admittance spectroscopy, which reveals a deep defect state ∼0.16 eV above the valence band. According to theoretical calculations, the defect state is possibly attributed to iodine interstitials (Ii), which can become the non-radiative recombination centers in the absorber.

Controllable self-induced passivation of hybrid lead iodide perovskites toward high performance solar cells.

To improve the performance of the polycrystalline thin film devices, it requires a delicate control of its grain structures. As one of the most promising candidates among current thin film photovoltaic techniques, the organic/inorganic hybrid perovskites generally inherit polycrystalline nature and exhibit compositional/structural dependence in regard to their optoelectronic properties. Here, we demonstrate a controllable passivation technique for perovskite films, which enables their compositional change, and allows substantial enhancement in corresponding device performance. By releasing the organic species during annealing, PbI2 phase is presented in perovskite grain boundaries and at the relevant interfaces. The consequent passivation effects and underlying mechanisms are investigated with complementary characterizations, including scanning electron microscopy (SEM), X-ray diffraction (XRD), time-resolved photoluminescence decay (TRPL), scanning Kelvin probe microscopy (SKPM), and ultraviolet photoemission spectroscopy (UPS). This controllable self-induced passivation technique represents an important step to understand the polycrystalline nature of hybrid perovskite thin films and contributes to the development of perovskite solar cells judiciously.

Rational defect passivation of Cu2ZnSn(S,Se)4 photovoltaics with solution-processed Cu2ZnSnS4:Na nanocrystals.

An effective defect passivation route has been demonstrated in the rapidly growing Cu2ZnSn(S,Se)4 (CZTSSe) solar cell device system by using Cu2ZnSnS4:Na (CZTS:Na) nanocrystals precursors. CZTS:Na nanocrystals are obtained by sequentially preparing CZTS nanocrystals and surface decorating of Na species, while retaining the kesterite CZTS phase. The exclusive surface presence of amorphous Na species is proved by X-ray photoluminescence spectrum and transmission electron microscopy. With Na-free glasses as the substrate, CZTS:Na nanocrystal-based solar cell device shows 50% enhancement of device performance (∼6%) than that of unpassivated CZTS nanocrystal-based device (∼4%). The enhanced electrical performance is closely related to the increased carrier concentration and elongated minority carrier lifetime, induced by defect passivation. Solution incorporation of extrinsic additives into the nanocrystals and the corresponding film enables a facile, quantitative, and versatile approach to tune the defect property of materials for future optoelectronic applications.

Pluronic F108 coating decreases the lung fibrosis potential of multiwall carbon nanotubes by reducing lysosomal injury.

We compared the use of bovine serum albumin (BSA) and pluronic F108 (PF108) as dispersants for multiwalled carbon nanotubes (MWCNTs) in terms of tube stability as well as profibrogenic effects in vitro and in vivo. While BSA-dispersed tubes were a potent inducer of pulmonary fibrosis, PF108 coating protected the tubes from damaging the lysosomal membrane and initiating a sequence of cooperative cellular events that play a role in the pathogenesis of pulmonary fibrosis. Our results suggest that PF108 coating could serve as a safer design approach for MWCNTs.

Surface-enhanced Raman spectroscopy to probe photoreaction pathways and kinetics of isolated reactants on surfaces: flat versus curved substrates.

We identify and control the photoreaction paths of self-assembled monolayers (SAMs) of thiolate-linked anthracene phenylethynyl molecules on Au substrate surfaces, and study the effects of nanoscale morphology of substrates on regioselective photoreactions. Two types of morphologies, atomically flat and curved, are produced on Au surfaces by controlling substrate structure and metal deposition. We employ surface-enhanced Raman spectroscopy (SERS), combined with Raman mode analyses using density functional theory, to identify the different photoreaction paths and to track the photoreaction kinetics and efficiencies of molecules in monolayers. The SAMs on curved surfaces exhibit dramatically lower regioselective photoreaction kinetics and efficiencies than those on atomically flat surfaces. This result is attributed to the increased intermolecular distances and variable orientations on the curved surfaces. Better understanding of the morphological effects of substrates will enable control of nanoparticle functionalization in ligand exchange in targeted delivery of therapeutics and theranostics and in catalysis.

Out-of-equilibrium processes in crystallization of organic-inorganic perovskites during spin coating.

Complex phenomena are prevalent during the formation of materials, which affect their processing-structure-function relationships. Thin films of methylammonium lead iodide (CH3NH3PbI3, MAPI) are processed by spin coating, antisolvent drop, and annealing of colloidal precursors. The structure and properties of transient and stable phases formed during the process are reported, and the mechanistic insights of the underlying transitions are revealed by combining in situ data from grazing-incidence wide-angle X-ray scattering and photoluminescence spectroscopy. Here, we report the detailed insights on the embryonic stages of organic-inorganic perovskite formation. The physicochemical evolution during the conversion proceeds in four steps: i) An instant nucleation of polydisperse MAPI nanocrystals on antisolvent drop, ii) the instantaneous partial conversion of metastable nanocrystals into orthorhombic solvent-complex by cluster coalescence, iii) the thermal decomposition (dissolution) of the stable solvent-complex into plumboiodide fragments upon evaporation of solvent from the complex and iv) the formation (recrystallization) of cubic MAPI crystals in thin film.

Slow thermal equilibration in methylammonium lead iodide revealed by transient mid-infrared spectroscopy.

Hybrid organic-inorganic perovskites are emerging semiconductors for cheap and efficient photovoltaics and light-emitting devices. Different from conventional inorganic semiconductors, hybrid perovskites consist of coexisting organic and inorganic sub-lattices, which present disparate atomic masses and bond strengths. The nanoscopic interpenetration of these disparate components, which lack strong electronic and vibrational coupling, presents fundamental challenges to the understanding of charge and heat dissipation. Here we study phonon population and equilibration processes in methylammonium lead iodide (MAPbI3) by transiently probing the vibrational modes of the organic sub-lattice following above-bandgap optical excitation. We observe inter-sub-lattice thermal equilibration on timescales ranging from hundreds of picoseconds to a couple of nanoseconds. As supported by a two-temperature model based on first-principles calculations, the slow thermal equilibration is attributable to the sequential phonon populations of the inorganic and organic sub-lattices, respectively. The observed long-lasting thermal non-equilibrium offers insights into thermal transport and heat management of the emergent hybrid material class.

Multichannel Interdiffusion Driven FASnI3 Film Formation Using Aqueous Hybrid Salt/Polymer Solutions toward Flexible Lead-Free Perovskite Solar Cells.

Tin (Sn)-based perovskites are increasingly attractive because they offer lead-free alternatives in perovskite solar cells. However, depositing high-quality Sn-based perovskite films is still a challenge, particularly for low-temperature planar heterojunction (PHJ) devices. Here, a "multichannel interdiffusion" protocol is demonstrated by annealing stacked layers of aqueous solution deposited formamidinium iodide (FAI)/polymer layer followed with an evaporated SnI2 layer to create uniform FASnI3 films. In this protocol, tiny FAI crystals, significantly inhibited by the introduced polymer, can offer multiple interdiffusion pathways for complete reaction with SnI2 . What is more, water, rather than traditional aprotic organic solvents, is used to dissolve the precursors. The best-performing FASnI3 PHJ solar cell assembled by this protocol exhibits a power conversion efficiency (PCE) of 3.98%. In addition, a flexible FASnI3 -based flexible solar cell assembled on a polyethylene naphthalate-indium tin oxide flexible substrate with a PCE of 3.12% is demonstrated. This novel interdiffusion process can help to further boost the performance of lead-free Sn-based perovskites.

Perovskite Solar Cells Employing Dopant-Free Organic Hole Transport Materials with Tunable Energy Levels.

Conjugated small-molecule hole-transport materials (HTMs) with tunable energy levels are designed and synthesized for efficient perovskite solar cells. A champion device with efficiency of 16.2% is demonstrated using a dopant-free DERDTS-TBDT HTM, while the DORDTS-DFBT-HTM-based device shows an inferior performance of 6.2% due to its low hole mobility and unmatched HOMO level with the valence band of perovskite film.

Overcoming Short-Circuit in Lead-Free CH3NH3SnI3 Perovskite Solar Cells via Kinetically Controlled Gas-Solid Reaction Film Fabrication Process.

The development of Sn-based perovskite solar cells has been challenging because devices often show short-circuit behavior due to poor morphologies and undesired electrical properties of the thin films. A low-temperature vapor-assisted solution process (LT-VASP) has been employed as a novel kinetically controlled gas-solid reaction film fabrication method to prepare lead-free CH3NH3SnI3 thin films. We show that the solid SnI2 substrate temperature is the key parameter in achieving perovskite films with high surface coverage and excellent uniformity. The resulting high-quality CH3NH3SnI3 films allow the successful fabrication of solar cells with drastically improved reproducibility, reaching an efficiency of 1.86%. Furthermore, our Kelvin probe studies show the VASP films have a doping level lower than that of films prepared from the conventional one-step method, effectively lowering the film conductivity. Above all, with (LT)-VASP, the short-circuit behavior often obtained from the conventional one-step-fabricated Sn-based perovskite devices has been overcome. This study facilitates the path to more successful Sn-perovskite photovoltaic research.

Improved air stability of perovskite solar cells via solution-processed metal oxide transport layers.

Lead halide perovskite solar cells have recently attracted tremendous attention because of their excellent photovoltaic efficiencies. However, the poor stability of both the perovskite material and the charge transport layers has so far prevented the fabrication of devices that can withstand sustained operation under normal conditions. Here, we report a solution-processed lead halide perovskite solar cell that has p-type NiO(x) and n-type ZnO nanoparticles as hole and electron transport layers, respectively, and shows improved stability against water and oxygen degradation when compared with devices with organic charge transport layers. Our cells have a p-i-n structure (glass/indium tin oxide/NiO(x)/perovskite/ZnO/Al), in which the ZnO layer isolates the perovskite and Al layers, thus preventing degradation. After 60 days storage in air at room temperature, our all-metal-oxide devices retain about 90% of their original efficiency, unlike control devices made with organic transport layers, which undergo a complete degradation after just 5 days. The initial power conversion efficiency of our devices is 14.6 ± 1.5%, with an uncertified maximum value of 16.1%.

10.5% efficient polymer and amorphous silicon hybrid tandem photovoltaic cell.

Thin-film solar cells made with amorphous silicon (a-Si:H) or organic semiconductors are considered as promising renewable energy sources due to their low manufacturing cost and light weight. However, the efficiency of single-junction a-Si:H or organic solar cells is typically <10%, insufficient for achieving grid parity. Here we demonstrate an efficient double-junction photovoltaic cell by employing an a-Si:H film as a front sub-cell and a low band gap polymer:fullerene blend film as a back cell on planar glass substrates. Monolithic integration of 6.0% efficienct a-Si:H and 7.5% efficient polymer:fullerene blend solar cells results in a power conversion efficiency of 10.5%. Such high-efficiency thin-film tandem cells can be achieved by optical management and interface engineering of fully optimized high-performance front and back cells without sacrificing photovoltaic performance in both cells.