Influence of Surface-Active Substances and Substrates on the Wettability of Individual Aerosol Particles during Condensation by Environmental Scanning Electron Microscopy.

The formation of liquid cloud droplets from aerosol particles in the Earth atmosphere is still under debate particularly because of the difficulties to quantify the importance of bulk and surface effects in these processes. Recently, single-particle techniques have been developed to access experimental key parameters at the scale of individual particles. Environmental scanning electron microscopy (ESEM) has the advantage to provide in situ monitoring of the water uptake of individual microscopic particles deposited on solid substrates. In this work, ESEM was used to compare droplet growth on pure ammonium sulfate (NH4)2SO4 and mixed sodium dodecyl sulfate/ammonium sulfate (SDS/(NH4)2SO4) particles and to explore the role of experimental parameters, such as the hydrophobic-hydrophilic character of the substrate, on this growth. With hydrophilic substrates, the growth on pure salt particles was strongly anisotropic, but this anisotropy was suppressed by the presence of SDS. With hydrophobic substrates, it is the wetting behavior of the liquid droplet that is impacted by the presence of SDS. The wetting behavior of the pure (NH4)2SO4 solution on a hydrophobic surface shows a step-by-step mechanism that can be attributed to successive pinning-depinning phenomena at the triple-phase line frontier. Unlike the pure (NH4)2SO4 solution, the mixed SDS/(NH4)2SO4 solution did not show such a mechanism. Therefore, the hydrophobic-hydrophilic character of the substrate plays an important role in the stability and dynamics of the liquid droplets' nucleation by water vapor condensation. In particular, hydrophilic substrates are not suited for the investigation of the hygroscopic properties (deliquescence relative humidity (DRH) and hygroscopic growth factor (GF)) of particles. Using hydrophobic substrates, data show that the DRH of (NH4)2SO4 particles is measured within 3% accuracy on the RH and their GF could indicate a size-dependent effect in the micrometer range. The presence of SDS does not seem to modify the DRH and GF of (NH4)2SO4 particles. This study shows that the water uptake on deposited particles is a complex process but, once carefully taken into account, ESEM is a suitable technique to study them.

Advanced synthesis of highly crystallized hexagonal boron nitride by coupling polymer-derived ceramics and spark plasma sintering processes-influence of the crystallization promoter and sintering temperature.

Hexagonal boron nitride nanosheets (BNNSs) are promising 2D materials due to their exceptional chemical and thermal stabilities together with their electrical insulation properties. A combined synthesis method involving the polymer-derived ceramics (PDCs) route and the spark plasma sintering (SPS) process is proposed, leading to well-crystallized and pure layered h-BN crystals, prone to be exfoliated into large BNNSs. Here we focus more specifically on the influence of two key parameters of the process to be optimized: the Li3N concentration (0-10 wt%) and the SPS temperature (1200 °C-1950 °C). The presence of Li3N, added as crystal promoter in the pre-ceramic powder, significantly improves the crystallinity level of the product, as evidenced by XRD, SEM and Raman spectrometry. SPS temperature strongly modifies the size of the resulting h-BN flakes. The influence of SPS temperature on both purity and crystallinity is studied using cathodoluminescence. h-BN flakes larger than 200 µm2 (average flake area) are obtained. Few-layered BNNSs are successfully isolated, through exfoliation process.

Comparative Study of Exsolved and Impregnated Ni Nanoparticles Supported on Nanoporous Perovskites for Low-Temperature CO Oxidation.

This study investigated the redox exsolution of Ni nanoparticles from a nanoporous La0.52Sr0.28Ti0.94Ni0.06O3 perovskite. The characteristics of exsolved Ni nanoparticles including their size, population, and surface concentration were deeply analyzed by environmental scanning electron microscopy (ESEM), transmission electron microscopy-energy dispersive X-ray spectroscopy (TEM-EDX) mapping, and hydrogen temperature-programmed reduction (H2-TPR). Ni exsolution was triggered in hydrogen as early as 400 °C, with the highest catalytic activity for low-temperature CO oxidation achieved after a reduction step at 500 °C, despite only a 10% fraction of Ni exsolved. The activity and stability of exsolved nanoparticles were compared with their impregnated counterparts on a perovskite material with a similar chemical composition (La0.65Sr0.35TiO3) and a comparable specific surface area and Ni loading. After an aging step at 800 °C, the catalytic activity of exsolved Ni nanoparticles at 300 °C was found to be 10 times higher than that of impregnated ones, emphasizing the thermal stability of Ni nanoparticles prepared by redox exsolution.

ZrCuAg Thin-Film Metallic Glasses: Toward Biostatic Durable Advanced Surfaces.

A combinatorial approach has served as a high-throughput strategy to identify compositional windows with optimized desired properties. Here, ZrCuAg thin-film metallic glasses were deposited by DC magnetron sputtering. For the purpose of using these coatings as biomedical surfaces, their durability in terms of mechanical and physicochemical properties as well as antibacterial properties were characterized. The effect of the chemical composition of thin films was studied. In particular, two key parameters were highlighted: the atomic ratio of Zr/Cu (with three values of 65/35, 50/50, and 35/65) and the silver content (from 1 to 16 at. %). All thin films are XRD amorphous and exhibit a typical veinlike pattern, which is characteristic of metallic glasses. They also show a dense and smooth surface and a hydrophobic behavior. Mechanical properties are found to be deeply influenced by the Zr/Cu ratio and the atomic structure. Although a low Zr/Cu ratio and/or a high silver content is detrimental to corrosion behavior, it favors the bactericidal effect of thin films. For all Zr/Cu ratios, ZrCuAg thin-film metallic glasses with silver contents higher than 12 at % are fully bactericidal. For lower silver contents, the bactericidal effect progressively decreases, which paves the way for a biostatic behavior of these surfaces.

Electron Tomography of Plasmonic Au Nanoparticles Dispersed in a TiO2 Dielectric Matrix.

Plasmonic Au nanoparticles (AuNPs) embedded into a TiO2 dielectric matrix were analyzed by combining two-dimensional and three-dimensional electron microscopy techniques. The preparation method was reactive magnetron sputtering, followed by thermal annealing treatments at 400 and 600 °C. The goal was to assess the nanostructural characteristics and correlate them with the optical properties of the AuNPs, particularly the localized surface plasmon resonance (LSPR) behavior. High-angle annular dark field-scanning transmission electron microscopy results showed the presence of small-sized AuNPs (quantum size regime) in the as-deposited Au-TiO2 film, resulting in a negligible LSPR response. The in-vacuum thermal annealing at 400 °C induced the formation of intermediate-sized nanoparticles (NPs), in the range of 10-40 nm, which led to the appearance of a well-defined LSPR band, positioned at 636 nm. Electron tomography revealed that most of the NPs are small-sized and are embedded into the TiO2 matrix, whereas the larger NPs are located at the surface. Annealing at 600 °C promotes a bimodal size distribution with intermediate-sized NPs embedded in the matrix and big-sized NPs, up to 100 nm, appearing at the surface. The latter are responsible for a broadening and a redshift, to 645 nm, in the LSPR band because of increase of scattering-to-absorption ratio. Beyond differentiating and quantifying the surface and embedded NPs, electron tomography also provided the identification of "hot-spots". The presence of NPs at the surface, individual or in dimers, permits adsorption sites for LSPR sensing and for surface-enhanced spectroscopies, such as surface-enhanced Raman scattering.

Dynamic Shaping of Femtoliter Dew Droplets.

Herein, we show that wetting properties such as giant wetting anisotropy and dynamic shaping can be observed when femtoliter (submicron scale) dew droplets are condensed on nanopatterned mildly hydrophilic surfaces. Large-scale, optically transparent, nanopatterned TiO2 surfaces were fabricated by direct nanoimprinting lithography of sol-gel-derived films. Square, infinitely elongated, or circular droplets were obtained with square, line, or concentric patterns, respectively, and were visualized in situ during formation and recession using optical microscopy and environmental scanning electronic microscopy. We first describe how extremely elongated droplets could form on mildly hydrophilic surfaces, naturally contaminated in real environmental conditions. In this configuration, the dew droplet shape can be dynamically and reversibly varied by controlling the out-of-equilibrium conditions associated with condensation/evaporation kinetics. As an example of the application, we propose a "morphological" sensor that exploits the shape of the dew droplets as a transduction mode for detecting organic vapors in the outer atmosphere. Importantly, this study is underlining that environmentally stable, purely hydrophilic surfaces can be smartly engineered to induce wetting phenomena at very small scale never observed so far for hydrophobic or heterogeneous surfaces. Our versatile approach based on nanoimprinted, transparent sol-gel films could open great perspectives for the implementation of environmentally stable, mildly hydrophilic materials for "dew engineering" applications such as open microfluidics, fuming for fingerprints, vapor sensing, or water harvesting on glass windows, for instance.

On the Potential of Bulk Metallic Glasses for Dental Implantology: Case Study on Ti40Zr10Cu36Pd14.

Ti40Zr10Cu36Pd14 Bulk Metallic Glass (BMG) appears very attractive for future biomedical applications thanks to its high glass forming ability, the absence of toxic elements such as Ni, Al or Be and its good mechanical properties. For the first time, a complete and exhaustive characterization of a unique batch of this glassy alloy was performed, together with ISO standard mechanical tests on machined implant-abutment assemblies. The results were compared to the benchmark Ti-6Al-4V ELI (Extra-Low-Interstitial) to assess its potential in dental implantology. The thermal stability, corrosion and sterilization resistance, cytocompatibility and mechanical properties were measured on samples with a simple geometry, but also on implant-abutment assemblies' prototypes. Results show that the glassy alloy exhibits a quite high thermal stability, with a temperature range of 38 °C between the glass transition and crystallization, a compressive strength of 2 GPa, a certain plastic deformation (0.7%), a hardness of 5.5 GPa and a toughness of 56 MPa.√m. Moreover, the alloy shows a relatively lower Young's modulus (96 GPa) than the Ti-6Al-4V alloy (110-115 GPa), which is beneficial to limit bone stress shielding. The BMG shows a satisfactory cytocompatibility, a high resistance to sterilization and a good corrosion resistance (corrosion potential of -0.07 V/SCE and corrosion current density of 6.0 nA/cm²), which may ensure its use as a biomaterial. Tests on dental implants reveal a load to failure 1.5-times higher than that of Ti-6Al-4V and a comparable fatigue limit. Moreover, implants could be machined and sandblasted by methods usually conducted for titanium implants, without significant degradation of their amorphous nature. All these properties place this metallic glass among a promising class of materials for mechanically-challenging applications such as dental implants.

Pure &crystallized 2D Boron Nitride sheets synthesized via a novel process coupling both PDCs and SPS methods.

Within the context of emergent researches linked to graphene, it is well known that h-BN nanosheets (BNNSs), also referred as 2D BN, are considered as the best candidate for replacing SiO2 as dielectric support or capping layers for graphene. As a consequence, the development of a novel alternative source for highly crystallized h-BN crystals, suitable for a further exfoliation, is a prime scientific issue. This paper proposes a promising approach to synthesize pure and well-crystallized h-BN flakes, which can be easily exfoliated into BNNSs. This new accessible production process represents a relevant alternative source of supply in response to the increasing need of high quality BNNSs. The synthesis strategy to prepare pure h-BN is based on a unique combination of the Polymer Derived Ceramics (PDCs) route with the Spark Plasma Sintering (SPS) process. Through a multi-scale chemical and structural investigation, it is clearly shown that obtained flakes are large (up to 30 µm), defect-free and well crystallized, which are key-characteristics for a subsequent exfoliation into relevant BNNSs.