RESUMO
The performance of blue quantum dot light-emitting diodes (QLEDs) is limited by unbalanced charge injection, resulting from insufficient holes caused by low mobility or significant energy barriers. Here, we introduce an angular-shaped heteroarene based on cyclopentane[b]thiopyran (C8-SS) to modify the hole transport layer poly-N-vinylcarbazole (PVK), in blue QLEDs. C8-SS exhibits high hole mobility and conductivity due to the π···π and S···π interactions. Introducing C8-SS to PVK significantly enhanced hole mobility, increasing it by 2 orders of magnitude from 2.44 × 10-6 to 1.73 × 10-4 cm2 V-1 s-1. Benefiting from high mobility and conductivity, PVK:C8-SS-based QLEDs exhibit a low turn-on voltage (Von) of 3.2 V. More importantly, the optimized QLEDs achieve a high peak power efficiency (PE) of 7.13 lm/W, which is 2.65 times that of the control QLEDs. The as-proposed interface engineering provides a novel and effective strategy for achieving high-performance blue QLEDs in low-energy consumption lighting applications.
RESUMO
Previous findings have suggested a close association between oxygen vacancies in SnO2 and charge carrier recombination as well as perovskite decomposition at the perovskite/SnO2 interface. Underlying the fundamental mechanism holds great significance in achieving a more favorable balance between the efficiency and stability. In this study, we prepared three SnO2 samples with different oxygen vacancy concentrations and observed that a low oxygen vacancy concentration is conducive to long-term device stability. Iodide ions were observed to easily diffuse into regions with high oxygen vacancies, thereby speeding up the deprotonation of FAI, as made evident by the detection of the decomposition product formamide. In contrast, a high oxygen vacancy concentration in SnO2 could prevent hole injection, leading to a decrease in interfacial recombination losses. To suppress this decomposition reaction and address the trade-off, we designed a bilayer SnO2 structure to ensure highly efficient carrier transport still while maintaining a chemically inert surface. As a result, an enhanced efficiency of 25.06% (certified at 24.55% with an active area of 0.09 cm2 under fast scan) was achieved, and the extended operational stability maintained 90% of their original efficiency (24.52%) after continuous operation for nearly 2000 h. Additionally, perovskite submodules with an active area of 14 cm2 were successfully assembled with a PCE of up to 22.96% (20.09% with an aperture area).
RESUMO
Due to their low cost and simplified production process, electron-transport-layer-free (ETL-free) perovskite solar cells (PSCs) have attracted great attention recently. However, the performance of ETL-free PSCs is still at a disadvantage compared to cells with a conventional n-i-p structure due to the severe recombination of charge carriers at the perovskite/anode interface. Here, we report a strategy to fabricate stable ETL-free FAPbI3 PSCs by in situ formation of a low dimensional perovskite layer between the FTO and the perovskite. This interlayer gives rise to the energy band bending and reduced defect density in the perovskite film and indirect contact and improved energy level alignment between the anode and perovskite, which facilitates charge carrier transport and collection and suppresses charge carrier recombination. As a result, ETL-free PSCs with a power conversion efficiency (PCE) exceeding 22% are achieved under ambient conditions.
RESUMO
Mixed tin-lead perovskite solar cells can reach bandgaps as low as 1.2 eV, offering high theoretical efficiency and serving as base materials for all-perovskite tandem solar cells. However, instability and high defect densities at the interfaces, particularly the buried surface, have limited performance improvements. In this work, we present the modification of the bottom perovskite interface with multifunctional hydroxylamine salts. These salts can effectively coordinate the different perovskite components, having critical influences in regulating the crystallization process and passivating defects of varying nature. The surface modification reduced traps at the interface and prevented the formation of excessive lead iodide, enhancing the quality of the films. The modified devices presented fill factors reaching 81% and efficiencies of up to 23.8%. The unencapsulated modified devices maintained over 95% of their initial efficiency after 2000 h of shelf storage.
RESUMO
Buried interface modification can effectively improve the compatibility between interfaces. Given the distinct interface selections in perovskite solar cells (PSCs), the applicability of a singular modification material remains limited. Consequently, in response to this challenge, we devised a tailored molecular strategy based on the electronic effects of specific functional groups. Therefore, we prepared three distinct silane coupling agents, and due to the varying inductive effects of these functional groups, the electronic distribution and molecular dipole moments of the coupling agents are correspondingly altered. Among them, trimethoxy (3,3,3-trifluoropropyl)-silane (F3 -TMOS), which possesses electron-withdrawing groups, generates a molecular dipole moment directed toward the hole transport layer (HTL). This approach changes the work function of the HTL, optimizes the energy level alignment, reduces the open-circuit voltage loss, and facilitates carrier transport. Furthermore, through the buffering effect of the coupling agent, the interface strain and lattice distortion caused by annealing the perovskite are reduced, enhancing the stability of the tin-based perovskite. Encouragingly, tin PSCs treated with F3 -TMOS achieved a champion efficiency of 14.67 %. This strategy provides an expedient avenue for the design of buried interface modification materials, enabling precise molecular adjustments in accordance with distinct interfacial contexts to ameliorate mismatched energetics and enhance carrier dynamics.
RESUMO
Quasi-two-dimensional (quasi-2D) perovskites are emerging as efficient emitters in blue perovskite light-emitting diodes (PeLEDs), while the imbalanced crystallization of the halide-mixed system limits further improvements in device performance. The rapid crystallization caused by Cl doping produces massive defects at the interface, leading to aggravated non-radiative recombination. Meanwhile, unmanageable perovskite crystallization is prone to facilitate the formation of nonuniform low-dimensional phases, which results in energy loss during the exciton transfer process. Here, we propose a multifunctional interface engineering for nucleation and phase regulation by incorporating the zwitterionic additive potassium sulfamate into the hole transport layer. By using potassium ions (K+ ) as heterogeneous nucleation seeds, finely controlled growth of interfacial K+ -guided grains is achieved. The sulfamate ions can simultaneously regulate the phase distribution and passivate defects through coordination interactions with undercoordinated lead atoms. Consequently, such synergistic effect constructs quasi-2D blue perovskite films with smooth energy landscape and reduced trap states, leading to pure-blue PeLEDs with a maximum external quantum efficiency (EQE) of 17.32 %, spectrally stable emission at 478â nm and the prolonged operational lifetime. This work provides a unique guide to comprehensively regulate the halide-mixed blue perovskite crystallization by manipulating the characteristics of grain-growth substrate.
RESUMO
Blue perovskite light-emitting diodes (PeLEDs) are crucial avenues for achieving full-color displays and lighting based on perovskite materials. However, the relatively low external quantum efficiency (EQE) has hindered their progression towards commercial applications. Quasi-two-dimensional (quasi-2D) perovskites stand out as promising candidates for blue PeLEDs, with optimized control over low-dimensional phases contributing to enhanced radiative properties of excitons. Herein, the impact of organic molecular dopants on the crystallization of various n-phase structures in quasi-2D perovskite films. The results reveal that the highly reactive bis(4-(trifluoromethyl)phenyl)phosphine oxide (BTF-PPO) molecule could effectively restrain the formation of organic spacer cation-ordered layered perovskite phases through chemical reactions, simultaneously passivate those uncoordinated Pb2+ defects. Consequently, the prepared PeLEDs exhibited a maximum EQE of 16.6 % (@ 490â nm). The finding provides a new route to design dopant molecules for phase modulation in quasi-2D PeLEDs.
RESUMO
Despite recent encouraging developments, achieving efficient blue perovskite light-emitting diodes (PeLEDs) have been widely considered a critical challenge. The efficiency breakthrough only occurred in the sky-blue region, and the device performance of pure-blue and deep-blue PeLEDs lags far behind those of their sky-blue counterparts. To avoid the negative effects associated with dimensionality reduction and excess chloride typically needed to achieve deep-blue emission, here we demonstrate guanidine (GA+)-induced deep-blue (â¼457 nm) perovskite emitters enabling spectrally stable PeLEDs with a record external quantum efficiency (EQE) over 3.41% through a combination of quasi-2D perovskites and halide engineering. Owing to the presence of GA+, even a small inclusion of chloride ions is sufficient for generating deep-blue electroluminescence (EL), in clear contrast to the previously reported deep-blue PeLEDs with significant chloride inclusion that negatively affects spectral stability. Based on the carrier dynamics analysis and theoretical calculation, GA+ is found to stabilize the low-dimensional species during annealing, retarding the cascade energy transfer and facilitating the deep-blue EL. Our findings open a potential third route to achieve deep-blue PeLEDs beyond the conventional methods of dimensionality reduction and excessive chloride incorporation.
RESUMO
Quasi-2D perovskites are enchanting alternative materials for solar cells due to their intrinsic stability. The manipulation of crystal orientation of quasi-2D perovskites is indispensable to target efficient devices, however, the origin of orientation during the film fabrication process still lacks in-depth understanding and convincing evidence yet, which hinders further boosting the performance of photovoltaic devices. Herein, the crystallizing processes during spin-coating and annealing are probed by in situ grazing-incidence wide-angle X-ray scattering (GIWAXS), and the incident-angle-dependent GIWAXS is conducted to unveil the phase distribution in the films. It is found that undesirable lead iodide sol-gel formed intermediate phase would disturb oriented crystalline growth, resulting in random crystal orientation in poor quasi-2D films. A general strategy is developed via simple additive agent incorporation to suppress the formation of the intermediate phase. Accordingly, highly oriented perovskite films with reduced trap density and higher carrier mobility are obtained, which enables the demonstration of optimized quasi-2D perovskite solar cells with a power conversion efficiency of 15.2% as well as improved stability. This work paves a promising way to manipulate the quasi-2D perovskites nucleation and crystallization processes via tuning nucleation stage.
RESUMO
Integrating anion-redox capacity with orthodox cation-redox capacity is deemed as a promising solution for high-energy-density battery cathodes surmounting the present technical bottlenecks. However, the evolution of oxidized oxygen species during the electrochemical or chemical process easily jeopardizes the reversibility of oxygen redox and remains poorly understood. Herein, we showcase the gradual conversion of the π-interacting oxygen (localized hole states on O) to the σ-interacting oxygen upon resting at a high voltage for P3-type Na0.6Li0.2Mn0.8O2 with nominally stable ribbon-like superstructure, accompanied by the O-O dimerization and the local structural reorganization. We further pinpoint an abnormal Li+ migration process from the alkali-metal layer to the transition-metal layer for desodiated P3-Na0.6Li0.2Mn0.8O2, thereby leading to a partial reconstruction of the ribbon superstructure. The high-voltage plateau of oxygen-redox cathodes is concluded to be exclusively controlled by the oxygen stabilization mechanism rather than the superstructure ordering. In addition, there exists a kinetic competition between π and σ interaction during the uninterrupted electrochemical process.
RESUMO
3D perovskites with low energy disorder and high ambipolar charge mobility represent a promising solution for efficient and bright light-emitting diodes. However, the challenges of regulating the nanocrystal size to trigger the quantum confinement effect and control the surface trap states to reduce charge loss hinder the applications of 3D perovskites in blue perovskite light-emitting diodes (PeLEDs). In this study, we present a top-down exfoliation method to obtain blue 3D perovskite films with clipped nanocrystals and tunable bandgaps by employing methyl cyanide (MeCN) for post-treatment. In this method, the MeCN solvent exfoliates the surface components of the 3D perovskite grains through a partial dissolution process. Moreover, the dissolved precursor can be further utilized to construct an ingenious 2D/3D heterostructure by incorporating an organic spacer into the MeCN solvent, contributing to efficient defect passivation and improved energy transfer. Consequently, efficient PeLEDs featuring ultrapure blue emission at 478 nm achieve a record external quantum efficiency of 12.3% among their 3D counterparts. This work emphasizes the significance of inducing the quantum confinement effect in 3D perovskites for efficient blue PeLEDs and provides a viable scheme for the in situ regulation of perovskite crystals.
RESUMO
Tin halide perovskites are an appealing alternative to lead perovskites. However, owing to the lower redox potential of Sn(II)/Sn(IV), particularly under the presence of oxygen and water, the accumulation of Sn(IV) at the surface layer will negatively impact the device's performance and stability. To this end, this work has introduced a novel multifunctional molecule, 1,4-phenyldimethylammonium dibromide diamine (phDMADBr), to form a protective layer on the surface of Sn-based perovskite films. Strong interactions between phDMADBr and the perovskite surface improve electron transfer, passivating uncoordinated Sn(II), and fortify against water and oxygen. In situ grazing incidence wide-angle X-ray scattering (GIWAXS) analysis confirms the enhanced thermal stability of the quasi-2D phase, and hence the overall enhanced stability of the perovskite. Long-term stability in devices is achieved, retaining over 90% of the original efficiency for more than 200 hours in a 10% RH moisture N2 environment. These findings propose a new approach to enhance the operational stability of Sn-based perovskite devices, offering a strategy in advancing lead-free optoelectronic applications.
RESUMO
Perovskite solar cells (PSCs) are developed rapidly in efficiency and stability in recent years, which can compete with silicon solar cells. However, an important obstacle to the commercialization of PSCs is the toxicity of lead ions (Pb2+) from water-soluble perovskites. The entry of free Pb2+ into organisms can cause severe harm to humans, such as blood lead poisoning, organ failure, etc. Therefore, this work reports a "lead isolation-capture" dual detoxification strategy with calcium disodium edetate (EDTA Na-Ca), which can inhibit lead leakage from PSCs under extreme conditions. More importantly, leaked lead exists in a nontoxic aggregation state chelated by EDTA. For the first time, in vivo experiments are conducted in mice to systematically prove that this material has a significant inhibitory effect on the toxicity of perovskites. In addition, this strategy can further enhance device performance, enabling the optimized devices to achieve an impressive power conversion efficiency (PCE) of 25.19%. This innovative strategy is a major breakthrough in the research on the prevention of lead toxicity in PSCs.
RESUMO
Mixed tin-lead (Sn-Pb) perovskites have attracted the attention of the community due to their narrow bandgap, ideal for photovoltaic applications, especially tandem solar cells. However, the oxidation and rapid crystallization of Sn2+ and the interfacial traps hinder their development. Here, cross-linkable [6,6]-phenyl-C61-butyric styryl dendron ester (C-PCBSD) is introduced during the quenching step of perovskite thin film processing to suppress the generation of surface defects at the electron transport layer interface and improve the bulk crystallinity. The C-PCBSD has strong coordination ability with Sn2+ and Pb2+ perovskite precursors, which retards the crystallization process, suppresses the oxidation of Sn2+, and improves the perovskite bulk and surface crystallinity, yielding films with reduced nonradiative recombination and enhanced interface charge extraction. Besides, the C-PCBSD network deposited on the perovskite surface displays superior hydrophobicity and oxygen resistance. Consequently, the devices with C-PCBSD obtain PCEs of up to 23.4% and retained 97% of initial efficiency after 2000 h of storage in a N2 atmosphere.
RESUMO
The interaction between sites A, B and X with passivation molecules is restricted when the conventional passivation strategy is applied in perovskite (ABX3) photovoltaics. Fortunately, the revolving A-site presents an opportunity to strengthen this interaction by utilizing an external field. Herein, we propose a novel approach to achieving an ordered magnetic dipole moment, which is regulated by a magnetic field via the coupling effect between the chiral passivation molecule and the A-site (formamidine ion) in perovskites. This strategy can increase the molecular interaction energy by approximately four times and ensure a well-ordered molecular arrangement. The quality of the deposited perovskite film is significantly optimized with inhibited nonradiative recombination. It manages to reduce the open-circuit voltage loss of photovoltaic devices to 360 mV and increase the power conversion efficiency to 25.22%. This finding provides a new insight into the exploration of A-sites in perovskites and offers a novel route to improving the device performance of perovskite photovoltaics.
RESUMO
A considerable efficiency gap exists between large-area perovskite solar modules and small-area perovskite solar cells. The control of forming uniform and large-area film and perovskite crystallization is still the main obstacle restricting the efficiency of PSMs. In this work, we adopted a solid-liquid two-step film formation technique, which involved the evaporation of a lead iodide film and blade coating of an organic ammonium halide solution to prepare perovskite films. This method possesses the advantages of integrating vapor deposition and solution methods, which could apply to substrates with different roughness and avoid using toxic solvents to achieve a more uniform, large-area perovskite film. Furthermore, modification of the NiOx/perovskite buried interface and introduction of Urea additives were utilized to reduce interface recombination and regulate perovskite crystallization. As a result, a large-area perovskite film possessing larger grains, fewer pinholes, and reduced defects could be achieved. The inverted PSM with an active area of 61.56 cm2 (10 × 10 cm2 substrate) achieved a champion power conversion efficiency of 20.56% and significantly improved stability. This method suggests an innovative approach to resolving the uniformity issue associated with large-area film fabrication.
RESUMO
Self-assembled monolayers (SAMs) have displayed great potential for improving efficiency and stability in p-i-n perovskite solar cells (PSCs). The anchoring of SAMs at the conductiv metal oxide substrates and their interaction with perovskite materials must be rationally tailored to ensure efficient charge carrier extraction and improved quality of the perovskite films. Herein, SAMs molecules with different anchoring groups and spacers to control the interaction with perovskite in the p-i-n mixed Sn-Pb PSCs are selected. It is found that the monolayer with the carboxylate group exhibits appropriate interaction and has a more favorable orientation and arrangement than that of the phosphate group. This results in reduced nonradiative recombination and enhanced crystallinity. In addition, the short chain length leads to an improved energy level alignment of SAMs with perovskite, improving hole extraction. As a result, the narrow bandgap (≈1.25 eV) Sn-Pb PSCs show efficiencies of up to 23.1% with an open-circuit voltage of up to 0.89 V. Unencapsulated devices retain 93% of their initial efficiency after storage in N2 atmosphere for over 2500 h. Overall, this work highlights the underexplored potential of SAMs for perovskite photovoltaics and provides essential findings on the influence of their structural modification.
RESUMO
Narrow bandgap cubic formamidine perovskite (α-FAPbI3) is widely studied for its potential to achieve recordbreaking efficiency. However, its high preparation difficulty caused by lattice instability is criticized. A popular strategy for stabilizing the α-FAPbI3 lattice is to replace intrinsic FA+ or I- with smaller ions of MA+, Cs+, Rb+, and Br-, whereas this generally leads to broadened optical bandgap and phase separation. Studies show that ions substitution-free phase-pure α-FAPbI3 can achieve intrinsic phase stability. However, the challenging preparation of high-quality films has hindered its further development. Here, a facile synthesis of high-quality MA+, Cs+, Rb+, and Br--free phase-pure α-FAPbI3 perovskite film by a new solution modification strategy is reported. This enables the activation of lead-iodine (PbâI) frameworks by forming the coated Pbâ¯O network, thus simultaneously promoting spontaneous homogeneous nucleation and rapid phase transition from δ to α phase. As a result, the efficient and stable phase-pure α-FAPbI3 PSC is obtained through a one-step method without antisolvent treatment, with a record efficiency of 23.15% and excellent long-term operating stability for 500 h under continuous light stress.
RESUMO
Interface-induced nonradiative recombination losses at the perovskite/electron transport layer (ETL) are an impediment to improving the efficiency and stability of inverted (p-i-n) perovskite solar cells (PSCs). Tridecafluorohexane-1-sulfonic acid potassium (TFHSP) is employed as a multifunctional dipole molecule to modify the perovskite surface. The solid coordination and hydrogen bonding efficiently passivate the surface defects, thereby reducing nonradiative recombination. The induced positive dipole layer between the perovskite and ETLs improves the energy band alignment, enhancing interface charge extraction. Additionally, the strong interaction between TFHSP and the perovskite stabilizes the perovskite surface, while the hydrophobic fluorinated moieties prevent the ingress of water and oxygen, enhancing the device stability. The resultant devices achieve a power conversion efficiency (PCE) of 24.6%. The unencapsulated devices retain 91% of their initial efficiency after 1000 h in air with 60% relative humidity, and 95% after 500 h under maximum power point (MPP) tracking at 35 °C. The utilization of multifunctional dipole molecules opens new avenues for high-performance and long-term stable perovskite devices.
RESUMO
Enhancing the quality of junctions is crucial for optimizing carrier extraction and suppressing recombination in semiconductor devices. In recent years, metal halide perovskite has emerged as the most promising next-generation material for optoelectronic devices. However, the construction of high-quality perovskite junctions, as well as characterization and understanding of their carrier polarity and density, remains a challenge. In this study, using combined electrical and spectroscopic characterization techniques, we investigate the doping characteristics of perovskite films by remote molecules, which is corroborated by our theoretical simulations indicating Schottky defects consisting of double ions as effective charge dopants. Through a post-treatment process involving a combination of biammonium and monoammonium molecules, we create a surface layer of n-type low-dimensional perovskite. This surface layer forms a heterojunction with the underlying 3D perovskite film, resulting in a favorable doping profile that enhances carrier extraction. The fabricated device exhibits an outstanding open-circuit voltage (VOC) up to 1.34 V and achieves a certified efficiency of 19.31% for single-junction wide-bandgap (1.77 eV) perovskite solar cells, together with significantly enhanced operational stability, thanks to the improved separation of carriers. Furthermore, we demonstrate the potential of this wide-bandgap device by achieving a certified efficiency of 27.04% and a VOC of 2.12 V in a perovskite/perovskite tandem solar cell configuration.