Optical characterization of the impact of 100 keV protons on the optical properties of ZrO2 films prepared by ALD on fused silica substrates.

Atomic layer deposition (ALD)-grown zirconia films underwent irradiation by 100 keV protons at fluences ranging from 1⋅1012 p +/c m 2 through 5⋅1014 p +/c m 2. The induced structural damage was modeled using the stopping and range of ions in matter (SRIM) and compared with the change of the optical properties characterized by ellipsometry, spectrophotometry, and x-ray reflectometry. Proton-induced contamination of the optical surface due to deposition of a carbon-rich layer was determined. Correct estimation of the substrate damage was shown to be critical for reliable evaluation of the optical constants of the irradiated films. The ellipsometric angle Δ is shown to be sensitive to both the presence of the buried damaged zone in the irradiated substrate and the contamination layer on the surface of the samples. The complex chemistry in carbon-doped zirconia accommodating over-stoichiometric oxygen is discussed, along with the impact of the film composition change on the refractive index of the irradiated films.

Patterned structures of in situ size controlled CdS nanocrystals in a polymer matrix under UV irradiation.

A method of in situ formation of patterns of size controlled CdS nanocrystals in a polymer matrix by pulsed UV irradiation is presented. The films consist of Cd thiolate precursors with different carbon chain lengths embedded in TOPAS polymer matrices. Under UV irradiation the precursors are photolyzed, driving to the formation of CdS nanocrystals in the quantum size regime, with size and concentration defined by the number of incident UV pulses, while the host polymer remains macroscopically/microscopically unaffected. The emission of the formed nanocomposite materials strongly depends on the dimensions of the CdS nanocrystals, thus, their growth at the different phases of the irradiation is monitored using spatially resolved photoluminescence by means of a confocal microscope. X-ray diffraction measurements verified the existence of the CdS nanocrystals, and defined their crystal structure for all the studied cases. The results are reinforced by transmission electron microscopy. It is proved that the selection of the precursor determines the efficiency of the procedure, and the quality of the formed nanocrystals. Moreover it is demonstrated that there is the possibility of laser induced formation of well-defined patterns of CdS nanocrystals, opening up new perspectives in the development of nanodevices.

New approach in Auger elemental relative sensitive factor calculation by using TEM-EDS analysis based on bi-layers of pure elements.

In fabrication of microelectronic devices two important steps are often recognized: i) all the processes performed on the wafer in order to build the active part of the devices and, ii) the assembly and packaging processes, typically performed on a chip, in order to fabricate interconnections between active part and exterior. The wafer back side is an active part of power devices and is normally coated with a stack of Ti-Ni-Au or Ti-Ni-Ag layers to ensure the best electrical contact with the frame on which the device is attached prior to the packaging. An important failure mechanism related to this particular process step is related to the diffusion of Ni to the surface of the stack that causes its oxidation on the back metal surface, inhibiting the correct connection to the metallic frame. Auger Electron Spectroscopy (AES) is a powerful analytical technique that can be used to detect this failure mechanism for its very high sensitivity in the characterization of surface layers. Unfortunately, its results are mainly qualitative. Quantitative extrapolations can be inaccurate using library Elemental Relative Sensitive Factor (ERSF) because they are mainly referred to a silicon substrate and could be not valid for a different matrix. A most accurate evaluation of the ERSF is based on the analysis, under identical experimental condition, of standard materials (with known concentration) that should be similar to the unknown sample and having the same matrix. However, the production of this kind of standard is not easy due to the mobility of Ni in Au and Ag. Another commonly used technique is the Energy Dispersive X-ray Spectrometry (EDS) which is less sensitive than the Auger and not sufficiently adequate for a quantitative analysis due to the limitation of the matrix correction methods. Recently, a new method to perform quantitative analysis by using Transmission Electron Microscopy (TEM) EDS was proposed, starting from bi-layers of pure elements. In this work we show how the use of TEM-EDS quantification of Ni in Ag could be a successful method for ERSF evaluation in order to overcome matrix effect in Auger quantification. For this purpose suitable foils of Ag/Al and Ni/Al were used. The validation of the method was performed on a sample with a tri-metal stack of Ti/Ni/Ag previously stimulated by means of a thermal budget to induce Ni migration on Ag surface. The quantitative analysis allowed us to use this characterized sample as AES standard for ERSF calculation.

Au nanoparticles prepared by physical method on Si and sapphire substrates for biosensor applications.

Gold nanoparticles heavily functionalized with oligonucleotides have been used in a variety of DNA detection methods. The optical properties of three-dimensional aggregates of Au nanoparticles in solution or deposited onto suitable surfaces have been analyzed to detect hybridization processes of specific DNA sequences as possible alternatives to fluorescent labeling methods. This paper reports on the preparation of gold nanoparticles directly deposited onto the surface of silicon (Si) and sapphire (Al2O3) substrates by a physical methodology, consisting in the thermal evaporation of a thin Au film and its successive annealing. The method guarantees the preparation of monodispersed single-crystal Au nanoparticles with a strong surface plasmon resonance (SPR) peak centered at about 540 nm. We show that the changes of SPR excitation before and after DNA functionalization and subsequent hybridization of Au nanoparticles immobilized onto Si and Al2O3 substrates can be exploited to fabricate specific biosensors devices in solid phase.