Unlocking the potential of one-carbon gases (CO2, CO) for concomitant bioproduction of ß-carotene and lipids.

This study investigates the use of a Yarrowia lipolytica strain for the bioconversion of syngas-derived acetic acid into ß-carotene and lipids. A two-stage process was employed, starting with the acetogenic fermentation of syngas by Clostridium aceticum, metabolising CO, CO2, H2, to produce acetic acid, which is then utilized by Y. lipolytica for simultaneous lipid and ß-carotene synthesis. The research demonstrates that acetic acid concentration plays a pivotal role in modulating lipid profiles and enhancing ß-carotene production, with increased acetic acid consumption leading to higher yields of these compounds. This approach showcases the potential of using one-carbon gases as substrates in bioprocesses for generating valuable bioproducts, providing a sustainable and cost-effective alternative to more conventional feedstocks and substrates, such as sugars.

Neural network-based performance assessment of one- and two-liquid phase biotrickling filters for the removal of a waste-gas mixture containing methanol, α-pinene, and hydrogen sulfide.

The performance of one- and two-liquid phase biotrickling filters (OLP/TLP-BTFs) treating a mixture of gas-phase methanol (M), α-pinene (P), and hydrogen sulfide (H) was assessed using artificial neural network (ANN) modeling. The best ANN models with the topologies 3-9-3 and 3-10-3 demonstrated an exceptional capacity for predicting the performance of O/TLP-BTFs, with R2 > 99%. The analysis of causal index (CI) values for the model of OLP-BTF revealed a negative impact of M on P removal (CI = -2.367), a positive influence of P and H on M removal (CI = +7.536 and CI = +3.931) and a negative effect of H on P removal (CI = -1.640). The addition of silicone oil in TLP-BTF reduced the negative impact of M and H on P degradation (CI = -1.261 and CI = -1.310, respectively) compared to the OLP-BTF. These findings suggested that silicone oil had the potential to improve P availability to the biofilm by increasing the concentration gradient of P between the air/gas and aqueous phases. Multi-objective particle swarm optimization (MOPSO) suggested an optimum operational condition, i.e. inlet M, P, and H concentrations of 1.0, 1.1, and 0.3 g m-3, respectively, with elimination capacities (ECs) of 172.1, 26.5, and 0.025 g m-3 h-1 for OLP-BTF. Likewise, one of the optimum operational conditions for TLP-BTF is achievable at inlet concentrations of 4.9, 1.7, and 0.8 g m-3, leading to the optimum ECs of 299.7, 52.9, and 0.072 g m-3 h-1 for M, P, and H, respectively. These results provide important insights into the treatment of complex waste gas mixtures, addressing the interactions between the pollutant removal characteristics in OLP/TLP-BTFs and providing novel approaches in the field of biological waste gas treatment.

Sequential bioconversion of C1-gases (CO, CO2, syngas) into lipids, through the carboxylic acid platform, with Clostridium aceticum and Rhodosporidium toruloides.

Syngas (CO, CO2, H2) was effectively bioconverted into lipids in a two-stage process. In the first stage, C1-gases were bioconverted into acetic acid by the acetogenic species Clostridium aceticum through the Wood-Ljungdahl metabolic pathway in a stirred tank bioreactor, reaching a maximum acetic acid concentration of 11.5 g/L, with a production rate of 0.05 g/L·h. Throughout this experiment, samples were extracted at different periods, i.e., different concentrations, to be used in the second stage, aiming at the production of lipids from acetic acid. The yeast Rhodosporidium toruloides, inoculated in the acetogenic medium, was able to efficiently accumulate lipids from acetic acid generated in the first stage. The best results, in terms of lipid content, dry biomass, biomass yield (Y(X/S)) and lipid yield (Y(L/S)) were 39.5% g/g dry cell weight, 3 g/L, 0.35 and 0.107, respectively. In terms of abundance, the lipid profile followed the order: C18:1 > C16:0 > C18:2 > C18:0 > Others. Experiments were also performed to determine the toxicity exerted by high concentrations of acetic acid on R. toruloides, resulting in inhibition at initial acid concentrations around 18 g/L leading to a higher lag phase and being lethal to the yeast at initial acetic acid concentrations around 22 g/L and above. This research paves the way for a novel method of growing oleaginous yeasts to produce sustainable biofuels from syngas or C1-pollutant gases.

Influence of feedstock mix ratio on microbial dynamics during acidogenic fermentation for polyhydroxyalkanoates production.

The nature of microbial populations plays an essential role in the production of volatile fatty acids (VFA) during acidogenesis, the first stage in polyhydroxyalkanoates (PHA) production using mixed cultures. However, the composition of microbial communities is generally affected by substrate alterations. This work aimed to unravel the microbial dynamics in response to a gradual change in the feedstock composition in an acidogenic reactor, with subsequent PHA production. To achieve this, co-digestion of cheese whey and brewery wastewater (BW) was carried out for the production of VFA, in which the ratio of these feedstocks was varied by gradually increasing the proportion of BW from 0 up to 50% of the organic content. Bacteria such as Megasphaera, Bifidobacterium or Caproiciproducens were the most abundant in the first stages of the co-digestion. However, when BW reached 25% of the organic load, new taxa emerged and displaced the former ones; like Selenomonas, Ethanoligenens or an undefined member of the Bacteroidales order. Accordingly, the production of butyric acid dropped from 52 down to 27%, while the production of acetic acid increased from 36 up to 52%. Furthermore, the gradual increase of the BW ratio led to a progressive drop in the degree of acidification, from 72 down to 57%. In a subsequent approach, the VFA-rich streams, obtained from the co-digestion, were used as substrates in PHA accumulation tests. All the tests yielded similar PHA contents, but with slightly different monomeric composition. The overall results confirmed that the microbiome was altered by a gradual change in the feedstock composition and, consequently, the VFA profile and the monomeric composition of the biopolymer also did.

Efficient production of n-caproate from syngas by a co-culture of Clostridium aceticum and Clostridium kluyveri.

In recent years, the possibility of merging technologies for waste recovery such as those based on syngas fermentation and chain elongation has been studied for the production of medium chain fatty acids (MCFAs) and bioalcohols, in an attempt to integrate the concept of circular economy in the industry. Nevertheless, one of the main issues of this approach is the pH mismatch between acetogens and chain elongating microorganisms. This work reports, for the first time, the suitability of a co-culture of C. aceticum and C. kluyveri metabolizing syngas at near neutral pH in stirred tank bioreactors. For this purpose, bioreactor studies were carried out with continuous syngas supply. In the first experiment, maximum concentrations of n-butyrate and n-caproate of 7.0 and 8.2 g/L, respectively, were obtained. In the second experiment, considerable amounts of n-butanol were produced as a result of the reduction, by C. aceticum, of the carboxylates already formed in the broth. In both experiments, ethanol was used as an exogenous electron agent at some point. Finally, batch bottle assays were performed with a pure culture of C. aceticum grown on CO in presence of n-butyrate to assess and confirm its ability to produce n-butanol, reaching concentrations up to 951 mg/L, with a n-butyrate conversion efficiency of 96%, which had never been reported before in this species. Therefore, this work contributes to the state of the art, presenting a novel system for the bioproduction of MCFAs by combining syngas fermentation and chain elongation at near neutral pH, as opposed to the acidic pH range used in all previously reported literature.

Production of chemicals from C1 gases (CO, CO2) by Clostridium carboxidivorans.

Bioprocesses in conventional second generation biorefineries are mainly based on the fermentation of sugars obtained from lignocellulosic biomass or agro-industrial wastes. An alternative to this process consists in gasifying those same feedstocks or even other carbon-containing materials to obtain syngas which can also be fermented by some anaerobic bacteria to produce chemicals or fuels. Carbon monoxide, carbon dioxide and hydrogen, which are the main components of syngas, are also found in some industrial waste gases, among others in steel industries. Clostridium carboxidivorans is able to metabolise such gases to produce ethanol and higher alcohols, i.e. butanol and hexanol, following the Wood-Ljungdahl pathway. This does simultaneously allow the removal of volatile pollutants involved in climate change. The bioconversion is a two step process in which organic acids (acetate, butyrate, hexanoate) are produced first, followed by the accumulation of alcohols; although partial overlap in time of acids and alcohols production may sometimes take place as well. Several parameters, among others pH, temperature, or gas-feed flow rates in bioreactors, affect the bioconversion process. Besides, the accumulation of high concentrations of alcohols in the fermentation broth inhibits the growth and metabolic activity of C. carboxidivorans.

Efficient butanol-ethanol (B-E) production from carbon monoxide fermentation by Clostridium carboxidivorans.

The fermentation of waste gases rich in carbon monoxide using acetogens is an efficient way to obtain valuable biofuels like ethanol and butanol. Different experiments were carried out with the bacterial species Clostridium carboxidivorans as biocatalyst. In batch assays with no pH regulation, after complete substrate exhaustion, acetic acid, butyric acid, and ethanol were detected while only negligible butanol production was observed. On the other side, in bioreactors, with continuous carbon monoxide supply and pH regulation, both C2 and C4 fatty acids were initially formed as well as ethanol and butanol at concentrations never reported before for this type of anaerobic bioconversion of gaseous C1 compounds, showing that the operating conditions significantly affect the metabolic fermentation profile and butanol accumulation. Maximum ethanol and butanol concentrations in the bioreactors were obtained at pH 5.75, reaching values of 5.55 and 2.66 g/L, respectively. The alcohols were produced both from CO fermentation as well as from the bioconversion of previously accumulated acetic and butyric acids, resulting in low residual concentrations of such acids at the end of the bioreactor experiments. CO consumption was often around 50% and reached up to more than 80%. Maximum specific rates of ethanol and butanol production were reached at pH 4.75, with values of 0.16 g/h*g of biomass and 0.07 g/h*g of biomass, respectively, demonstrating that a low pH was more favorable to solventogenesis in this process, although it negatively affects biomass growth which does also play a role in the final alcohol titer.

Carbon monoxide bioconversion to butanol-ethanol by Clostridium carboxidivorans: kinetics and toxicity of alcohols.

Butanol production from carbon monoxide-rich waste gases or syngas is an attractive novel alternative to the conventional acetone-butanol-ethanol (ABE) fermentation. Solvent toxicity is a key factor reported in ABE fermentation with carbohydrates as substrates. However, in the gas-fermentation process, kinetic aspects and the inhibition effect of solvents have not thoroughly been studied. Therefore, different batch bottle experiments were carried out with the bacterial species Clostridium carboxidivorans using CO as carbon source for butanol-ethanol fermentation. A maximum specific growth rate of 0.086 ± 0.004 h(-1) and a biomass yield of 0.011 gbiomass/gCO were found, which is significantly lower than in other clostridia grown on sugars. Besides, three assays were carried out to check the inhibitory effect of butanol, ethanol, and their mixtures. Butanol had a higher inhibitory effect on the cells than ethanol and showed a lower IC50, reduced growth rate, and slower CO consumption with increasing alcohol concentrations. A concentration of 14-14.50 g/L butanol caused 50 % growth inhibition in C. carboxidivorans, and 20 g/L butanol resulted in complete inhibition, with a growth rate of 0 h(-1). Conversely, 35 g/L ethanol decreased by 50 % the final biomass concentration respect to the control and yielded the lowest growth rate of 0.024 h(-1). The inhibitory effect of mixtures of both alcohols was also checked adding similar, near identical, concentrations of each one. Growth decreased by 50 % in the presence of a total concentration of alcohols of 16.22 g/L, consisting of similar amounts of each alcohol. Occasional differences in initially added concentrations of alcohols were minimal. The lowest growth rate (0.014 h(-1)) was observed at the highest concentration assayed (25 g/L).

Carbon dioxide as key player in chain elongation and growth of Clostridium kluyveri: Insights from batch and bioreactor studies.

Chain elongation technology allows medium-chain fatty acids (MCFAs) production as an alternative to fossil resources. Clostridium kluyveri generates n-caproate primarily from ethanol and acetate, presumably requiring CO2 for growth. Here, the impact of CO2 on C. kluyveri was explored. Bottle studies revealed the bacterium's adaptability to low CO2 levels, even in conditions with minimal dissolved NaHCO3 (0.0003 M) and unfavorable pH (below 6) under 1 bar CO2. Bioreactor investigations demonstrated a direct correlation between CO2 availability and bacterial growth. The highest n-caproate production (11.0 g/L) with 90.1 % selectivity was achieved in a bioreactor with continuous CO2 supply at 3 mL/min. Additional bottle experiments pressurized with 1 bar CO2 and varying ethanol:acetate ratios (1:1, 2:1, 4:1) also confirmed CO2 consumption by C. kluyveri. However, increasing the ethanol:acetate ratio did not enhance n-caproate selectivity, likely due to overly acidic pH conditions. These findings provide insights into chain-elongators responses under diverse conditions.

Clostridium carboxidivorans and Rhodosporidium toruloides as a platform for the valorization of carbon dioxide to microbial oils.

There is growing scientific interest in oleaginous yeasts producing microbial oils as precursors of biofuels and potential substitutes for fossil fuels. Due to the high cost of substrates commonly metabolized by yeasts, volatile fatty acids (VFAs) are gaining interest as alternative cheap and sustainable carbon sources, which can be obtained from solid, liquid and gas pollutants. In this research, Rhodosporidium toruloides was proven to be able to accumulate microbial oils from VFAs obtained from the fermentation of syngas by Clostridium carboxidivorans. Using CO2 and CO as carbon sources from the syngas mixture and H2 as energy source, this acetogen produced, via the Wood-Ljungdahl pathway, a mixture of acetic, butyric and caproic acids. It was first revealed that R. toruloides exhibited minimal inhibition at concentrations below 12 g/L when exposed to a mixture of VFAs, which included acetic, butyric and even hexanoic acids. The yeast was then grown on the culture medium derived from the acetogenic fermentation of syngas. Between the two yeast strains tested of the same species, R. toruloides DSM 4444 reached a total VFAs consumption of 69.1 g/L, supplied by successive additions of acids to the reactor, yielding a maximum lipid content of 29.7% w/w cell. The lipid profile obtained in this case, in terms of abundance followed the order C18:1 > C16:0 ≥ C18:0 > C18:2>others; in which the dominant compound (C18:1), represented approximately 50% of the total. This research opens new possibilities in the cultivation of oleaginous yeasts for the production of biofuels and bioproducts from C1 gases.

Bioconversion of pure CO2 to caproic acid with zero valent iron: Optimizing carbon flux distribution in co-cultures of Acetobacterium woodii and Megasphaera hexanoica.

Acetobacterium woodii and Megasphaera hexanoica were co-cultured for caproic acid (CA) production from lactic acid (LA) and CO2. Also, various concentrations (1 g/L, 3 g/L, 5 g/L, and 10 g/L) of Zero Valent Iron (ZVI) were supplied to study its impact on the co-culture system. In flask experiments, 10 g/L LA and 1.0 bar CO2 produced 0.6 g/L CA with some biomass growth. ZVI increased LA consumption and CA production. Indeed, 3 g/L ZVI boosted CA production by 186 % and biomass accumulation by 103 %, suggesting that ZVI controls the carbon flux. Subsequent automated bioreactor studies showed that 3 g/L ZVI produced 1.842 g/L CA at stable pH, compared to 0.969 g/L without ZVI (control). Further, metabolic activity showed that both bacteria could directly use H2, generated by ZVI (3 g/L), as electron donor. Higher ZVI concentrations (10 g/L) resulted in Fe2+ causing excessive oxidation pressure on M. hexanoica, with its carbon flux flowing preferentially towards biomass. Enzyme assays confirmed that A. woodii preferred 10 g/L ZVI while M. hexanoica preferred 3 g/L for optimal bioconversion.

Effect of electron acceptors on product selectivity and carbon flux in carbon chain elongation with Megasphaera hexanoica.

Megasphaera hexanoica is a bacterial strain following the reverse ß-oxidation pathway to synthesize caproate (CA) using lactate (LA) as an electron donor (ED) and acetate (AA) or butyrate (BA) as electron acceptors (EA). Differences in the type and concentration of EA lead to distinctions in product distribution and energy bifurcation of carbon fluxes in ED pathways, thereby affecting CA production. In this study, the effect of various ratios of AA, BA, and AA+BA as EA on carbon flux and CA specific titer during the carbon chain elongation in M. hexanoica was explored. The results indicated that the maximum levels of CA were 18.81 mM and 31.48 mM when the molar ratios of LA/AA and LA/BA were 10:1 and 3:1, respectively. Meanwhile, when AA and BA were used as combined EA (LA, AA, and BA molar amounts of 100, 23, and 77 mM), a maximum CA production of 39.45 mM was obtained. Further analysis revealed that the combined EA exhibited a CA production carbon flux of 49 % (4.3 % and 19.5 % higher compared to AA or BA, respectively) and a CA production specific titer of 45.24 mol (80.89 % and 58.51 % higher compared to AA or BA, respectively), indicating that the effective carbon utilization rate and CA production efficiency were greatly improved. Finally, a scaled-up experiment was conducted in a 1.2 L (working volume) automated bioreactor, implying high biomass (optical density at 600 nm or OD600 = 1.809) and a slight decrease in CA production (28.45 mM). A decrease in H2 production (4.11 g/m3) and an increase in CO2 production (0.632 g/m3) demonstrated the appropriate metabolic adaptation of M. hexanoica to environmental changes such as stirring shear.

Comprehensive comparative study on n-caproate production by Clostridium kluyveri: batch vs. continuous operation modes.

Recently, there has been notable interest in researching and industrially producing medium-chain carboxylic acids (MCCAs) like n-caproate and n-caprylate via chain elongation process. This study presents a comprehensive assessment of the behavior and MCCA production profiles of Clostridium kluyveri in batch and continuous modes, at different ethanol:acetate molar ratios (1.5:1, 3.5:1 and 5.5:1). The highest n-caproate concentration, 12.9 ± 0.67 g/L (92.9 ± 1.39 % MCCA selectivity), was achieved in batch mode at a 3.5:1 ratio. Interestingly, higher ratios favored batch mode selectivity over continuous mode when this was equal or higher to 3.5:1. Steady state operation yielded the highest n-caproate (9.5 ± 0.13 g/L) and n-caprylate (0.35 ± 0.020 g/L) concentrations at the 3.5:1 ratio. Increased ethanol:acetate ratios led to a higher excessive ethanol oxidation (EEO) in both operational modes, potentially limiting n-caproate production and selectivity, especially at the 5.5:1 ratio. Overall, this study reports the efficient MCCA production of both batch and continuous modes by C. kluyveri.

Optimization of methane production from solid tuna waste: Thermal pretreatment and co-digestion.

Fish canning industries generate large amounts of solid waste during their processing operations, creating a significant environmental challenge. Nonetheless, this waste can be efficiently and sustainably treated through anaerobic digestion. In this study, the potential of biogas production from anaerobic digestion of thermally pretreated and co-digested solid tuna waste was investigated. The thermal pretreatment of raw fish viscera resulted in a 50 % increase in methane yield, with a production of 0.27 g COD-CH4/g COD added. However, this pretreatment did not lead to a significant increase in biogas production for cooked tuna viscera. When non-thermally pretreated raw viscera was tested, a large accumulation of volatile fatty acids and long chain fatty acids was observed, with levels reaching 21 and 6 g COD/L, respectively. On the other hand, anaerobic co-digestion of cooked tuna viscera with fat waste significantly enhanced methane production, achieving 0.87 g COD-CH4/g COD added. In contrast, co-digestion of cooked tuna viscera with dairy waste and sewage sludge resulted in notably lower yields of 0.36 and 0.46 g COD-CH4/g COD added, respectively. These results may be related to the C/N ratio, which was found to be within the optimal range for anaerobic digestion only in the tuna and fat waste co-digestion assay.

Hydrothermal extraction of ulvans from Ulva spp. in a biorefinery approach.

A simple cascade process based on the hydrothermal fractionation of Ulva spp. biomass was proposed. Considering the overall extraction yields (50 %), ulvan recovery (23 %), and ulvan composition, structural, mechanical and cytotoxic properties, the selected optimal final heating temperature was 160 °C. Ethanol precipitation provided the highest ulvan recovery yields but choline chloride precipitated ulvans showed stronger mechanical properties, G´ moduli 1.5·104 Pa and 3·104 Pa for ethanol and for choline chloride, respectively. Both products were safe on NCTC 929 mouse fibroblasts and after a cooling stage, formed films without requiring any additives. From the ulvan-free liquid fraction, one product with 43 % (wt, d.b.) phenolics and moderate antiradical properties and a byproduct containing nutrients and minerals were separated. The methane potential of the corresponding residual solids was influenced by the hydrothermal heating temperature and was doubled compared to than for the untreated seaweed biomass (60 mL/g VS). This scheme could be also applied to the wet algal biomass, in a chemical free alternative to provide ready to use ulvan biopolymers, bioactives, nutrients, salts and biogas, conforming a biorefinery approach.

Effect of pH and medium composition on chain elongation with Megasphaera hexanoica producing C4-C8 fatty acids.

Introduction: Chain elongation technology, which involves fermentation with anaerobic bacteria, has gained attention for converting short and medium chain substrates into valuable and longer-chain products like medium chain fatty acids (MCFAs). In the recent past, the focus of studies with pure chain elongating cultures was on species of other genera, mainly Clostridium kluyveri. Recently, other chain elongators have been isolated that deserve further research, such as Megasphaera hexanoica. Methods: In this study, batch studies were performed in bottles with two different media to establish the optimal conditions for growth of M. hexanoica: (a) a medium rich in different sources of nitrogen and (b) a medium whose only source of nitrogen is yeast extract. Also, batch bioreactor studies at pH values of 5.8, 6.5 and 7.2 were set up to study the fermentation of lactate (i.e., electron donor) and acetate (i.e., electron acceptor) by M. hexanoica. Results and discussion: Batch bottle studies revealed the yeast extract (YE) containing medium as the most promising in terms of production/cost ratio, producing n-caproate rapidly up to 2.62 ± 0.24 g/L. Subsequent bioreactor experiments at pH 5.8, 6.5, and 7.2 confirmed consistent production profiles, yielding C4-C8 fatty acids. A fourth bioreactor experiment at pH 6.5 and doubling both lactate and acetate concentrations enhanced MCFA production, resulting in 3.7 g/L n-caproate and 1.5 g/L n-caprylate. H2 and CO2 production was observed in all fermentations, being especially high under the increased substrate conditions. Overall, this study provides insights into M. hexanoica's behavior in lactate-based chain elongation and highlights optimization potential for improved productivity.

Comparative assessment of the performance of one- and two-liquid phase biotrickling filters for the simultaneous abatement of gaseous mixture of methanol, α-pinene, and hydrogen sulfide.

A gaseous mixture of methanol (M), α-pinene (P), and hydrogen sulfide (H) was treated in one/two-liquid phase biotrickling filters (OLP/TLP-BTFs) at varying inlet concentrations and at an empty bed residence time (EBRT) of 57 s. The performance of TLP-BTF [BTF (A)] improved significantly in terms of M and P removal due to the presence of silicone oil at 5% v/v. The maximum elimination capacities (ECs) of M, P, and H in BTF (A) were obtained as 309, 73, and 56 g m-3 h-1, respectively. While, the maximum ECs achieved in the BTF operated without silicone oil [BTF (B)] were 172, 28, and 21 g m-3 h-1 for M, P, and H removal, respectively. Increasing the inlet concentration of H from 32 to 337 ppm inhibited P removal in both the BTFs. The presence of silicone oil enhanced gas-liquid mass transfer, prevented the BTF from experiencing substrate inhibition effects and allowed reaching high ECs for M and P. The experiments showed promising results for the long-term operation of removal of M, P, and H mixture in a one-stage TLP-BTF with the decreasing negative effects of M and H on P degradation.

Integrated fermentative process for lipid and ß-carotene production from acetogenic syngas fermentation using an engineered oleaginous Yarrowia lipolytica yeast.

An engineered Yarrowia lipolytica strain was successfully employed to produce ß-carotene and lipids from acetic acid, a product of syngas fermentation by Clostridium aceticum. The strain showed acetic acid tolerance up to concentrations of 20 g/L. Flask experiments yielded a peak lipid content of 33.7 % and ß-carotene concentration of 13.6 mg/g under specific nutrient conditions. The study also investigated pH effects on production in bioreactors, revealing optimal lipid and ß-carotene contents at pH 6.0, reaching 22.9 % and 44 mg/g, respectively. Lipid profiles were consistent across experiments, with C18:1 being the dominant compound at approximately 50 %. This research underscores a green revolution in bioprocessing, showing how biocatalysts can convert syngas, a potentially polluting byproduct, into valuable ß-carotene and lipids with a Y. lipolytica strain.

Production of biofuels from C1 -gases with Clostridium and related bacteria-Recent advances.

Clostridium spp. are suitable for the bioconversion of C1 -gases (e.g., CO2 , CO and syngas) into different bioproducts. These products can be used as biofuels and are reviewed here, focusing on ethanol, butanol and hexanol, mainly. The production of higher alcohols (e.g., butanol and hexanol) has hardly been reviewed. Parameters affecting the optimization of the bioconversion process and bioreactor performance are addressed as well as the pathways involved in these bioconversions. New aspects, such as mixotrophy and sugar versus gas fermentation, are also reviewed. In addition, Clostridia can also produce higher alcohols from the integration of the Wood-Ljungdahl pathway and the reverse ß-oxidation pathway, which has also not yet been comprehensively reviewed. In the latter process, the acetogen uses the reducing power of CO/syngas to reduce C4 or C6 fatty acids, previously produced by a chain elongating microorganism (commonly Clostridium kluyveri), into the corresponding bioalcohol.

Production of short-chain fatty acids (SCFAs) as chemicals or substrates for microbes to obtain biochemicals.

Carboxylic acids have become interesting platform molecules in the last years due to their versatility to act as carbon sources for different microorganisms or as precursors for the chemical industry. Among carboxylic acids, short-chain fatty acids (SCFAs) such as acetic, propionic, butyric, valeric, and caproic acids can be biotechnologically produced in an anaerobic fermentation process from lignocellulose or other organic wastes of agricultural, industrial, or municipal origin. The biosynthesis of SCFAs is advantageous compared to chemical synthesis, since the latter relies on fossil-derived raw materials, expensive and toxic catalysts and harsh process conditions. This review article gives an overview on biosynthesis of SCFAs from complex waste products. Different applications of SCFAs are explored and how these acids can be considered as a source of bioproducts, aiming at the development of a circular economy. The use of SCFAs as platform molecules requires adequate concentration and separation processes that are also addressed in this review. Various microorganisms such as bacteria or oleaginous yeasts can efficiently use SCFA mixtures derived from anaerobic fermentation, an attribute that can be exploited in microbial electrolytic cells or to produce biopolymers such as microbial oils or polyhydroxyalkanoates. Promising technologies for the microbial conversion of SCFAs into bioproducts are outlined with recent examples, highlighting SCFAs as interesting platform molecules for the development of future bioeconomy.