Spectral Investigations of Fluorescence Tracers in Automotive and Aviation Fuels under Cryogenic Conditions.

This study investigated spectral laser-induced fluorescence signals of dyes in fuels for automotive and aerospace applications under low temperatures and cryogenic conditions down to 183 K. For this purpose, a fluorescence chamber was developed based on cooling with liquid nitrogen. The design enabled a minimal inner chamber temperature of 153 K. Furthermore, the applicability of two-color LIF for liquid thermometry was evaluated under these conditions. The temperature determination was based on the temperature-sensitive fluorescence intensity ratio of the special dyes doped into the fuels determined in suitable spectral regions, which represented common bandpass filters. For this purpose, the fluorescence signals of the dye doped into the gasoline and jet fuel surrogate isooctane were tested as well as blends of isooctane and the ethanol biofuels E20 (comprising 80 vol.% isooctane and 20 vol.% ethanol), E40, and E100. Additionally, a realistic multi-component fuel Jet A-1 mixed with a suitable fluorescence dye was investigated. E100 was doped with Eosin-Y, and the remaining fuels were doped with Nile red. Temperature-dependent spectral LIF intensities were recorded in the range of 183 K-293 K, which simulate extreme environments for aerospace and automotive applications. Frozen fuel-dye mixtures cause significant extinction effects and prevent sufficient signal detection at low and cryogenic temperatures, defining the detection limit. A temperature decrease led to a spectral shift in the emission peaks of E100 doped with Eosin-Y toward shorter wavelengths, while the spectra of mixtures doped with Nile red were shifted toward longer wavelengths. The suggested bandpass filters produced the temperature-sensitive intensity ratio (the average over the temperature interval) of the dyes with the largest sensitivity for Jet A-1 (5.2%/K), followed by E100 (4.95%/K), E40 (4.07%/K), E20 (3.23%/K), and isooctane (3.07%/K), even at cryogenic temperatures.

Chairside measurement of the marginal and internal fit of crowns: a new intraoral scan-based approach.

OBJECTIVES: To investigate the marginal and internal fit of crowns, a new intraoral scanner-based digital approach for chairside measurement (D-IOS) was systematically analysed and compared with the conventional silicone replica technique (CV-SR) and digital 3D analysis software (D-GOM). MATERIALS AND METHODS: Two models, representing different clinical situations, were constructed, and the first molar was prepared for a full-coverage crown. On the basis of an intraoral scan (Trios 3), copings of three different materials (non-precious alloy, zirconium dioxide, and resin composite) with two different cement spaces (80 µm, 50 µm) were manufactured. The fit of the copings was investigated by all three methods (CV-SR, D-IOS, D-GOM). Therefore, the cement space was visualized with low-viscosity silicone and digitalized with a second intraoral scan. Evaluation of fit by the D-IOS-method was measured in the intraoral scanner software, whereas for analysis by D-GOM, both intraoral scan datasets were transferred to 3D analysis software (GOM Inspect). The CV-SR-method was used as a control group. For all copings, the measurements were repeated five times. The data were analysed with ANOVA. RESULTS: No significant differences between the three evaluation methods and the coping materials were shown. However, in the occlusal area, the internal gap was significantly higher compared to the internal gap in the marginal and axial areas regardless of the cement space setting (p < .05). The target parameter of the cement spaces did not match the actual measured internal gaps. CONCLUSIONS: All three evaluation methods and coping materials can be used for the measurement of fit within different clinical situations. CLINICAL RELEVANCE: The digital chairside measurement implemented in the intraoral scanner software enables an easy, applicable evaluation of fit of crowns without additional laboratory devices or special software applications.

How long must a post be? A retrospective survival analysis on a large cohort with long follow-ups.

OBJECTIVES: Post and core (PC) is frequently used, but clinical evidence concerning how long a post must be is scarce. Recommendations in dental literature range from half of the root which should be incorporated, to post space preparations conducted as deep as possible increasing the risk for root perforation thus tooth loss. Therefore, the aim of this retrospective survival analysis is to evaluate the post length as well as the post-clinical crown ratio on a large patient cohort with long follow-ups. MATERIALS AND METHODS: Overall 1026 PC in 731 patients could be included in this study (2004-2023). The files were analysed due to the parameters post length and post-clinical crown ratio on X-Ray. Furthermore, the influence of the type of covering prosthetic restoration, location, type of tooth, luting material, PC material, bone attachment and therapist was evaluated. The statistical analysis was assessed using Kaplan-Meier (univariate influences) and Cox regression (multifactorial influences). RESULTS: Survival until extraction as well as decementation was significantly influenced by bone attachment and covering prosthetic restoration. Posts reaching the middle third of the root showed highly significant (p < 0.001) better survival probabilities than those reaching the coronal or apical third. Regarding the post-clinical crown ratio, no significant difference was found for post = crown/post > crown, whereas post

Post and Core Treatment to Refit Telescopic Crown-Retained Dentures after Abutment Tooth Fracture: An Evaluation of Therapy by Retrospective Survival Analysis.

Telescopic crown-retained dentures (TCDs) are one of the most common types of prosthetic restorations for partially edentulous patients; however, post and core (PC) treatment shows the worst survival probability if the tooth is used as an abutment for the TCD. Due to extra axial forces, abutment tooth fracture is a common cause of failure for TCDs; thus, PC treatment is often needed to refit the existing telescopic crown (TC). However, there are no clinical survival data on whether the PC treatment was used to refit the TC after abutment tooth fracture (PC2) or the PC was already fitted at the time of TCD treatment (PC1). A total of 246 patients with 399 PC treatments were retrospectively evaluated for follow-ups up to 17.33 years. The files were analysed for PC1 and PC2. Furthermore, the influence of the jaw, type of tooth, luting material, PC material, bone attachment, therapist and cause of failure was recorded. For statistical analysis, Kaplan-Meier and Cox regression analyses were conducted. PC2 showed highly significant lower survival probabilities than PC1 (p < 0.001). Moreover, the bone attachment and the age of the patient at the time of fitting the PC crown had an influence on the survival (p < 0.001). Therefore, PC2 should be carefully discussed with the patient and PC1 should be favoured in endodontically treated abutment teeth for TCDs.

Survival of Double Crown-Retained Implant-Tooth-Supported Removable Partial Dentures: A ≥ 5-Year Clinical Follow-up Study.

PURPOSE: This retrospective clinical follow-up study assesses double-crown retained implanttooth- supported removable partial dentures (DCR-ITSRPDs) survival, evaluates abutment survival and identifies first aftercare measures. MATERIALS AND METHODS: The influence of various factors on the survival of the DCR-ITSRPDs and the abutments were observed in this retrospective clinical follow-up study using Kaplan-Meier estimate. In addition, the first occurred aftercare measure per prosthesis was evaluated. RESULTS: 47 DCR-ITSRPDs were investigated (mean observation: 4.3 ± 3.8 years; max. 14.3 years) out of which three (6.4%) had to be replaced. The 5- and 10- year survival probability for DCR-ITSRPDs was 100% and 75%. A total of 297 abutments (120 natural teeth and 177 dental implants) were observed, of which 22 (7.4%; 6 teeth and 16 implants) failed. The 5- and 10-year survival probability for teeth was 90.2% and for dental implants 90.4% and 76.3%. CONCLUSION: DCR-ITSRPDs are a successful and durable treatment option for patients with substantially reduced residual dentitions. Both, prostheses and abutments show good survival times after 5- and 10-years in function. The patient associated factors tested showed no influence on the survival of DCR-ITSRPs and abutments. Peri implant infection was the decisive factor for abutment loss, therefore, regular dental prophylaxis and examinations are of major importance.

Fibre-reinforced Cad/CAM post and cores: The new "gold standard" for anterior teeth with extensive coronal destruction?-A fully digital chairside workflow.

Objectives: Since one-third of persons suffer a dental trauma, treatment of anterior teeth using post and core (PC) is becoming important. In teeth with extensive destruction, cast PC (CPC) remain the "gold standard", even though they lead to aesthetic impairment and have a mismatching elastic modulus to that of dentin. Prefabricated fibre-reinforced posts have elastic modulus similar to that of dentin but the accuracy of fit and mechanical stability are worse. This study was aimed to evaluate the deviation and mechanical performance of fibre-reinforced CAD/CAM PC (FRPC) fabricated in a fully digital chairside workflow, compared to those of CPC. Methods: On 30 teeth, a PC preparation was conducted, and a conventional and digital post impression were taken with an intraoral scanner. Fifteen teeth each were treated with CPC and FRPC, respectively. The deviation was evaluated by superimposing the datasets of the digitalised stone models and digital post impressions. Decementation and root fracture during chewing simulation were analysed by microscopy and X-ray. Statistical analysis was performed by pairwise comparison and Kaplan-Meier analysis. Results: The median deviation for the "coronal", "middle" and "apical" were 14.5, 18.0 and 113.7 µm, respectively. The pairwise comparison for "coronal"/"middle" showed no significance (p = 0.465), whereas that for "coronal"/"apical" and "middle"/"apical" showed highly significant differences (p < 0.001). After chewing simulation, five decementations and two root fractures were detected for CPC. For FRPC, neither decementation nor root fracture were documented. Significance: Within the limitations of this study, FRPC performed significantly better than CPC.

Conventional cast vs. CAD/CAM post and core in a fully digital chairside workflow - An in vivo comparative study of accuracy of fit and feasibility of impression taking.

OBJECTIVES: Clinical data for CAD/CAM post and cores (PC) is still scarce, even though developments in digital dentistry have improved dental treatment in many aspects. Therefore, the purpose of this in vivo study was to compare CAD/CAM PC fabricated in a fully digital chairside workflow to conventional cast PC (CPC) according to the accuracy of fit and the impression taking. The null hypothesis was that there is no significant difference between CAD/CAM PC and CPC. METHODS: The study was conducted on 30 teeth in 25 patients receiving a CPC during their prosthetic treatment plan. On each tooth a conventional and a digital post impression were taken. Subsequently, one CPC following a conventional and one CAD/CAM PC following a digital workflow were fabricated. Both PC were tried-in intraorally and assessed according to a standardised evaluation sheet. The deviation between the two impression methods was evaluated by superimposing the datasets in a 3D analysis software. Statistical analysis for pairwise comparison was conducted according to Wilcoxon and median test with a significance level of p = 0.05. RESULTS: CAD/CAM PC performed significantly better compared to CPC according to accuracy of fit (p = 0.022) and feasibility of impression taking (p < 0.001). The deviation between post impression methods increased from "coronal" to "apical". Between "coronal"/"middle" no significant difference (p = 0.158) was detected, whereas the pairwise comparison between the other measurement categories showed significant differences (p = 0.002, p < 0.001). CONCLUSIONS: The null hypothesis was rejected since CAD/CAM PC performed significantly better and the deviation between the post impression methods showed significant differences. CLINICAL SIGNIFICANCE: By using intraoral scanners (IOS) teeth can be restored with customised CAD/CAM PC in a single session. Within the limitations of this study the fully digital chairside workflow led to superior accuracy of fit of PC and higher feasibility of impression taking than the conventional workflow for CPC.

Survival of teeth treated with post and core - A retrospective study of more than 1000 cases with observation periods up to 18 years.

OBJECTIVES: Even if survival of post and core (PC) itself was frequently investigated in recent literature, clinical data concerning the risk for extraction of teeth restored with PC is still scarce. Since most authors found the loss of retention of refitable post and cores as the most common cause of failure, it is impossible to draw a conclusion on tooth survival on the results of those studies. Therefore, the aim of the present study was to improve the clinical evidence on the survival of teeth treated with post and cores on a large number of cases over a long observation period. MATERIALS AND METHODS: 735 patients were treated with 1053 post and cores in the observation period (2004-2022) and could be included in the study. The patient files were analysed due to the parameters: Type of covering prosthetic restoration, location, type of tooth, luting material, post and core material, bone attachment and therapist. The survival probability was assessed using Kaplan-Meyer analysis. Cox regression was used to assess possible multifactorial influences. RESULTS: The overall average survival time until necessary extraction of a tooth restored with a post and core was 11.74 years. A root fracture in primary crown retained removeable partial dentures (RPDs) during the first five years was the most common reason for extraction in this study. A significant influence on the survival time of teeth restored with post and cores was found for the type of covering restoration, bone attachment, age of the patient and post and core material. CONCLUSIONS: Post and core restored teeth should be avoided as abutments for primary crown retained RPDs. CLINICAL SIGNIFICANCE: If it is inevitable to utilise post and core restored teeth for primary crown retained RPDs, post and core materials with matching mechanical properties to that of dentine should be preferred.

Survival time of post and cores: A 16 year retrospective follow-up study.

OBJECTIVES: The retrospective survival study (1995-2004) by Balkenhol et al. [1]. led to changes in the decision-making process for treatment with post and cores (special focus on the covering prosthetic restoration while deciding for treatment with post and cores, high primary friction at the try-in stage for conventional cementation, only indirect fabrication technique, no semi-precious alloy) in our clinic. The aim of this study was to examine the influence of these changes on the survival probability. MATERIALS AND METHODS: In the observation period (2004-2020) 653 patients received in total 953 post and cores. The patient files were analysed due to the parameters: Type of covering prosthetic restoration, location, type of tooth, luting material, post and core material, bone attachment, therapist and cause of failure. According to the previous study the survival probability was assessed using Kaplan-Meyer analysis. Cox regression was used to assess the risk of failure and identify possible covariates. RESULTS: The average survival time of the post and cores was 10.9 years. The cumulative failure rate was 28.2%. A significant influence on the survival time (Kaplan-Meyer analysis) could be found for the parameters: Type of covering prosthetic restoration, location, type of tooth, post and core material and bone attachment. The multifactorial survival analysis (Cox regression) showed a significant influence of the age of the patient at the time of fitting the post, the type of covering prosthetic restoration and the bone attachment. CONCLUSIONS: The changes in the decision-making process did not lead to a better survival probability. CLINICAL SIGNIFICANCE: The conclusions stated in the previous study were not strict enough. Treatments with post and cores should be critically scrutinized on the basis of covering prosthetic restoration and bone attachment. Post and cores under primary crown retained RPDs should be avoided because of the bad survival probability.

Survival time of post and cores after recementation: A 16-year retrospective study with special focus on loss of retention.

OBJECTIVES: Numerous studies investigating the survival time of post and cores have found that loss of retention is the most common cause of failure Nevertheless, investigations focusing on decementation, survival after recementation, and the influencing parameters in a large number of patients with long follow-up periods are lacking. Therefore, the aim of this short communication article is the survival analysis of post and cores after recementation and repeated loss of retention. MATERIALS AND METHODS: During the observation period (2004-2020), 653 patients received 953 post and cores. From these, 112 post and cores which suffered loss of retention were selected. The patient files were analysed for the following parameters: Type of covering prosthetic restoration, location, type of tooth, luting material, post and core material, bone attachment and therapist. The survival time until loss of retention or repeated decementations after recementation was documented. Survival probability was assessed using Kaplan-Meier and Cox regression analyses. RESULTS: The average time until decementation was 13.33 years. The cumulative decementation rate was 11.8%, while in 42.0% of the cases, post and cores showed multiple losses of retention. A significant influence (Kaplan-Meier analysis) was recorded for the type of covering prosthetic restoration, type of tooth, luting material, post and core material and bone attachment. The multifactorial survival analysis (Cox regression) showed a significant influence of patient's age and the type of covering prosthetic restoration. CONCLUSIONS: Once decementation occurs, recementation neither guarantees definitive fit nor necessarily predetermines repeated decementations. CLINICAL SIGNIFICANCE: Post and cores should be avoided under primary crown-retained removable partial dentures (RPD). If this treatment is inevitable, a continuous follow-up is necessary to check the denture for proper fit to the tissues to prevent overloading on the post and core.

Accuracy of Digital Impression Taking with Intraoral Scanners and Fabrication of CAD/CAM Posts and Cores in a Fully Digital Workflow.

Current intraoral scanners (IOS) enable direct impression taking for computer-aided de-sign/computer-aided manufacturing (CAD/CAM) posts and cores (P+C) with subsequent milling out of monolithic materials. The aim of this in vitro study was to systematically investigate the accuracy of CAD/CAM-P+C in a fully digital workflow, considering different IOS impression methods (Primescan (PRI), Trios4 without (TRI) and with scanpost (TRI+SP)) (Part A), and CAD/CAM milling of zirconium dioxid (ZIR) and resin composite (COM)-P+C (Part B). Five human models were developed in this study. Micro-CT imaging was used as a reference (REF). For Part A, the models were scanned 12 times for each impression method. Then, IOS datasets (n = 180) were superimposed with REF, and scan accuracy was determined using 3D software (GOMInspect). For Part B, one CAD/CAM-P+C (n = 30) was milled for each model, impression method, and material. The triple-scan method was applied using an industrial scanner (ATOS) to determine the accuracy of the fit. Statistical analysis was performed using analysis of variance (ANOVA, p < 0.05). Part A showed for PRI significantly lower accuracy than TRI and TRI+SP (p < 0.05). The data of Part B revealed significantly higher accuracy for ZIR than for COM (p < 0.05). Within the limitations of this study, CAD/CAM-P+C of the ZIR can be recommended for fabrication in a fully digital workflow regarding the accuracy of fit.

New Intraoral Scanner-Based Chairside Measurement Method to Investigate the Internal Fit of Crowns: A Clinical Trial.

To measure the internal fit of the computer-aided designed/computer-aided manufactured (CAD/CAM) crowns, a new scanner-based chairside approach was investigated in patients, and the results were compared to the established silicone replica technique and a digital laboratory replica method. Thirty full-coverage crown preparations were included. Based on a digital impression with an intraoral scanner (IOS, Trios 3), three CAD/CAM measurement copings ('COM', resin composite; 'ZIR', zirconium dioxide; 'NPA', non-precious alloy) were fabricated for each tooth preparation. The internal fit of the measurement copings was analyzed with three different evaluation methods: IOS-based digital approach (D-IOS), digital replica method with laboratory software (D-GOM), and conventional silicone replica technique (CV-SR). The congruence between the determined target parameter of the 80-µm cement space and the actual measured internal gap was investigated. Statistical analysis was performed by ANOVA (p-value < 0.05). No significant difference was determined between the three evaluation methods. However, significant differences were observed for the three coping materials (p-value < 0.05), the single measurement position (marginal, axial, and occlusal fit) (p-value < 0.05), and the interaction between the coping material and the measurement position (p-value < 0.05). COM revealed the smallest internal gap, followed by ZIR and NPA. Regardless of the coping material, the occlusal gap was higher than the axial and marginal gaps. Furthermore, only the internal gaps of the marginal area almost matched the target parameter of 80-µm for the cement space. D-IOS is effective for measuring internal fit of single crowns in different clinical settings.