Improving the Thermodynamic Energy Efficiency of Battery Electrode Deionization Using Flow-Through Electrodes.

Ion intercalation electrodes are being investigated for use in mixed capacitive deionization (CDI) and battery electrode deionization (BDI) systems because they can achieve selective ion removal and low energy deionization. To improve the thermodynamic energy efficiency (TEE) of these systems, flow-through electrodes were developed by coating porous carbon felt electrodes with a copper hexacyanoferrate composite mixture. The TEE for ion separation using flow-through electrodes was compared to a system using flow-by electrodes with the same materials. The flow-through BDI system increased the recoverable energy nearly 3-fold (0.009 kWh m-3, compared to a 0.003 kWh m-3), which increased the TEE from ∼6% to 8% (NaCl concentration reduction from 50 to 42 mM; 10 A m-2, 50% water recovery, and 0.5 mL min-1). The TEE was further increased to 12% by decreasing the flow rate from 0.50 to 0.25 mL min-1. These findings suggest that, under similar operational conditions and materials, flow-through battery electrodes could achieve better energy recovery and TEE for desalination than flow-by electrodes.

Antibacterial rGO-CuO-Ag film with contact- and release-based inactivation properties.

To reduce the high operational costs of water treatment because of membrane biofouling, next-generation materials are being developed to counteract microbial growth. These modern anti-biofouling strategies are based on new membrane materials or membrane surface modifications. In this study, antimicrobial films comprising rGO, rGO-CuO, rGO-Ag, and rGO-CuO-Ag were synthesized, evaluated, and tested for potential biofouling control using Pseudomonas aeruginosa PAO1 as the model bacterium. The combined rGO-CuO-Ag film displayed enhanced reduction (10-log reduction) in biofouling in comparison to the rGO film (control), followed by the rGO-Ag film (8-log reduction) and rGO-CuO film (0-log reduction). This demonstrated that the use of mixed antimicrobial agents is more effective in reducing biofouling than that of a single agent. The rGO-CuO-Ag film exhibited consistent, controlled, and moderate release of silver (Ag) ions. The release of Ag ions produced a long-lasting antimicrobial effect. These results underscore the potential applications of combined antimicrobial surface-based agents in practice and further research.

Effect of phosphate availability on biofilm formation in cooling towers.

Phosphate limitation has been suggested as a preventive method against biofilms. P-limited feed water was studied as a preventive strategy against biofouling in cooling towers (CTs). Three pilot-scale open recirculating CTs were operated in parallel for five weeks. RO permeate was fed to the CTs (1) without supplementation (reference), (2) with supplementation by biodegradable carbon (P-limited) and (3) with supplementation of all nutrients (non-P-limited). The P-limited water contained ≤10 µg PO4 l-1. Investigating the CT-basins and coupons showed that P-limited water (1) did not prevent biofilm formation and (2) resulted in a higher volume of organic matter per unit of active biomass compared with the other CTs. Exposure to external conditions and cycle of concentration were likely factors that allowed a P concentration sufficient to cause extensive biofouling despite being the limiting compound. In conclusion, phosphate limitation in cooling water is not a suitable strategy for CT biofouling control.

Implications of Chemical Reduction Using Hydriodic Acid on the Antimicrobial Properties of Graphene Oxide and Reduced Graphene Oxide Membranes.

The antimicrobial properties of graphene-based membranes such as single-layer graphene oxide (GO) and modified graphene oxide (rGO) on top of cellulose ester membrane are reported in this study. rGO membranes are made from GO by hydriodic acid (HI) vapor treatment. The antibacterial properties are tested after 3 h contact time with selected model bacteria. Complete bacterial cell inactivation is found only after contact with rGO membranes, while no significant bacterial inactivation is found for the control i) GO membrane, ii) the mixed cellulose ester support, and the iii) rGO membrane after additional washing that removes the remaining HI. This indicates that the antimicrobial effect is neither caused by the graphene nor the membrane support. The antimicrobial effect is found to be conclusively linked to the HI eliminating microbial growth, at concentrations from 0.005%. These findings emphasize the importance of caution in the reporting of antimicrobial properties of graphene-based surfaces.

Characterization of the bacterial community in shower water before and after chlorination.

Bathers release bacteria in swimming pool water, but little is known about the fate of these bacteria and potential risks they might cause. Therefore, shower water was characterized and subjected to chlorination to identify the more chlorine-resistant bacteria that might survive in a chlorinated swimming pool and therefore could form a potential health risk. The total community before and after chlorination (1 mg Cl2 L-1 for 30 s) was characterized. More than 99% of the bacteria in the shower water were Gram-negative. The dominant bacterial families with a relative abundance of ≥10% of the total (non-chlorinated and chlorinated) communities were Flavobacteriaceae (24-21%), Xanthomonadaceae (23-24%), Moraxellaceae (12-11%) and Pseudomonadaceae (10-22%). The relative abundance of Pseudomonadaceae increased after chlorination and increased even more with longer contact times at 1 mg Cl2L-1. Therefore, Pseudomonadaceae were suggested to be relatively more chlorine resistant than the other identified bacteria. To determine which bacteria could survive chlorination causing a potential health risk, the relative abundance of the intact cell community was characterized before and after chlorination. The dominant bacterial families in the intact community (non-chlorinated and chlorinated) were Xanthomonadaceae (21-17%) and Moraxellaceae (48-57%). Moraxellaceae were therefore more chlorine resistant than the other identified intact bacteria present.

Enhancing the DNA yield intended for microbial sequencing from a low-biomass chlorinated drinking water.

DNA extraction yield from drinking water distribution systems and premise plumbing is a key metric for any downstream analysis such as 16S amplicon or metagenomics sequencing. This research aimed to optimize DNA yield from low-biomass (chlorinated) reverse osmosis-produced tap water by evaluating the impact of different factors during the DNA extraction procedure. The factors examined are (1) the impact of membrane materials and their pore sizes; (2) the impact of different cell densities; and (3) an alternative method for enhancing DNA yield via incubation (no nutrient spiking). DNA from a one-liter sampling volume of RO tap water with varying bacterial cell densities was extracted with five different filter membranes (mixed ester cellulose 0.2 µm, polycarbonate 0.2 µm, polyethersulfone 0.2 and 0.1 µm, polyvinylidene fluoride 0.1 µm) for biomass filtration. Our results show that (i) smaller membrane pore size solely did not increase the DNA yield of low-biomass RO tap water; (ii) the DNA yield was proportional to the cell density and substantially dependent on the filter membrane properties (i.e., the membrane materials and their pore sizes); (iii) by using our optimized DNA extraction protocol, we found that polycarbonate filter membrane with 0.2 µm pore size markedly outperformed in terms of quantity (DNA yield) and quality (background level of 16S gene copy number) of recovered microbial DNA; and finally, (iv) for one-liter sampling volume, incubation strategy enhanced the DNA yield and enabled accurate identification of the core members (i.e., Porphyrobacter and Blastomonas as the most abundant indicator taxa) of the bacterial community in low-biomass RO tap water. Importantly, incorporating multiple controls is crucial to distinguish between contaminant/artefactual and true taxa in amplicon sequencing studies of low-biomass RO tap water.

Biofilm rigidity, mechanics and composition in seawater desalination pretreatment employing ultrafiltration and microfiltration membranes.

The choice of appropriate biofilm control strategies in membrane systems for seawater desalination pretreatment relies on understanding the properties of the biofilm formed on the membrane. This study reveals how the biofilm composition, including both organic and inorganic, influenced the biofilm behavior under mechanical loading. The investigation was conducted on two Gravity-Driven Membrane reactors employing Microfiltration (MF) and Ultrafiltration (UF) membrane for the pretreatment of raw seawater. After a stabilization period of 20 days (Phase I), a biofilm behavior test was introduced (Phase II) to evaluate (i) biofilm deformation during the absence of permeation (i.e., relaxation) and (ii) biofilm resistance to detachment forces (i.e., air scouring). The in-situ monitoring investigation using Optical Coherence Tomography (OCT) revealed that the biofilms developed on MF and UF membrane presented a rigid structure in absence of filtration forces, limiting the application of relaxation and biofilm expansion necessary for cleaning. Moreover, under shear stress conditions, a higher reduction in biofilm thickness was observed for MF (-60%, from 84 to 34 µm) compared to UF (-30%, from 64 to 45 µm), leading to an increase of permeate flux (+60%, from 9.1 to 14.9 L/m2/h and +20 % from 7.8 to 9.5 L/m2/h, respectively). The rheometric analysis indicated that the biofilm developed on MF membrane had weaker mechanical strength, displaying lower storage modulus (-50 %) and lower loss modulus (-55 %) compared to UF. These differences in mechanical properties were linked to the lower concentration of polyvalent ions and the distribution of organic foulants (i.e., BB, LMW-N) found in the biofilm on the MF membrane. Moreover, in the presence of air scouring led to a slight difference in microbial community between UF and MF. Our findings provide valuable insight for future investigations aimed at engineer biofilm composition to optimize biofilm control strategies in membrane systems for seawater desalination pretreatment.

A comprehensive evaluation of the temporal and spatial fouling characteristics of RO membranes in a full-scale seawater desalination plant.

The fouling of seawater reverse osmosis (SWRO) membranes remains a persistent challenge in desalination. Previous research has focused mainly on fouling separately; however, organic, inorganic, and biofouling can coexist and influence each other. Hence, in-depth study of the spatiotemporal changes in actual combined fouling in full-scale seawater desalination will provide more effective information for fouling investigation and control. In this study, we monitored (i) the operational performance of a full-scale desalination plant for 7 years and (ii) the development and characterization of membrane and spacer fouling at different locations of spiral-wound membrane modules sampled after 2.5-, 3.5-, and 7-year operation. The findings showed that (i) operational performance indicators declined with time (normalized flux 40 % reduction, salt rejection 2 % in 7 years), with a limited effect of the 20-day cleaning frequency, (ii) fouling accumulation in the membrane module mainly occurred at the feed side of the lead module and the microbial community in these area exhibited the highest diversity, (iii) the dominant microbial OTUs belonged mainly to Proteobacteria (43-70 %), followed by Bacteroidetes (10-11 %), (iv) Phylogenetic molecular ecological networks and Spearman correlation analysis revealed that Chloroflexi (Anaerolineae) and Planctomycetes were keystone species in maintaining the community structure and biofilm maturation and significantly impacted the foulant content on the SWRO membrane, even with low abundance, and that (v) fouling accumulation was composed of polysaccharides, soluble microbial products, marine humic acid-like substances, and inorganic Ca/Fe/Mg/Si dominate the fouling layer of both the membrane and spacer. Overall, variation partitioning analysis quantitatively describes the increasing contribution of biofouling over time. Ultimately, the organic‒inorganic-biofouling interaction (70 %) significantly contributed to the overall fouling of the membrane after 7 years of operation. These results can be used to develop more targeted fouling control strategies to optimize SWRO desalination plant design and operation.

Nanoplastics induced health risk: Insights into intestinal barrier homeostasis and potential remediation strategy by dietary intervention.

Aged nanoplastics (aged-NPs) have unique characteristics endowed by environmental actions, such as rough surface, high oxygen content. Although studies have highlighted the potential hazards of aged-NPs, limited research has provided strategies for aged-NPs pollution remediation. The dietary intervention of quercetin is a novel insight to address the health risks of aged-NPs. This study explored the impact of aged-NPs on intestinal barrier homeostasis at the environmentally relevant dose and investigated the alleviating effects of quercetin on aged-NPs toxicity through transcriptomics and molecular biology analysis. It indicated that aged-NPs induced intestinal barrier dysfunction, which was characterized by higher permeability, increased inflammation, and loss of epithelial integrity, while quercetin restored it. Aged-NPs disrupted redox homeostasis, upregulated inflammatory genes controlled by AP-1, and led to Bax-dependent mitochondrial apoptosis. Quercetin intervention effectively mitigated inflammation and apoptosis by activating the Nrf2. Thus, quercetin decreased intestinal free radical levels, inhibiting the phosphorylation of p38 and JNK. This study unveiled the harmful effects of aged-NPs on intestinal homeostasis and the practicability of dietary intervention against aged-NPs toxicity. These findings broaden the understanding of the NPs toxicity and provide an effective dietary strategy to relieve the health risks of NPs. ENVIRONMENTAL IMPLICATIONS: Growing levels of NPs pollution have represented severe health hazards to the population. This study focuses on the toxic mechanism of aged-NPs on the intestinal barrier and the alleviating effect of quercetin dietary intervention, which considers the environmental action and relevant dose. It revealed the harmful effects of aged-NPs on intestinal inflammation with the key point of free radical generation. Furthermore, a quercetin-rich diet holds significant promise for addressing and reversing intestinal damage caused by aged-NPs by maintaining intracellular redox homeostasis. These findings provide an effective dietary strategy to remediate human health risks caused by NPs.

A robust thin-film droplet-induced electricity generator.

The pursuit of cost-effective, high-voltage electricity generators activated by droplets represents a new frontier in hydropower technology. This study presents an economical method for crafting droplet generators using common materials such as solid polytetrafluoroethylene (PTFE) films and readily available tapes, eliminating the need for specialized cleanroom facilities. A thorough investigation into voltage-limiting factors, encompassing device capacitance and induced electrode charges, reveals specific areas with potential for optimization. A substantial enhancement in the open-circuit voltage (Voc) was achieved, reaching approximately 282.2 ± 27.9 V-an impressive increase of around 60 V compared to earlier benchmarks. One device showcased its capability to power 100 LEDs concurrently, underscoring its efficacy. Ten such devices created diverse luminous patterns with uniform light intensity for each LED, showcasing the practical potential of the approach. The methodology's cost-effectiveness results in a remarkable cost reduction compared to solution-based materials, paving the way for the widespread adoption of large-scale water droplet energy harvesting.

Airfoil-shaped filament feed spacer for improved filtration performance in water treatment.

Optimal spacer design enhances the filtration performance in spiral-wound modules by controlling the local hydrodynamics inside the filtration channel. A novel airfoil feed spacer design fabricated using 3D-printing technology is proposed in this study. The design is a ladder-shaped configuration with primary airfoil-shaped filaments facing the incoming feed flow. The airfoil filaments are reinforced by cylindrical pillars supporting the membrane surface. Laterally, all the airfoil filaments are connected by thin cylindrical filaments. The performances of the novel airfoil spacers are evaluated at Angle of Attack (AOA) of 10° (A-10 spacer) and 30° (A-30 spacer) and compared with commercial (COM) spacer. At fixed operating conditions, simulations indicate steady-state hydrodynamics inside the channel for A-10 spacer, while an unsteady state is found for A-30 spacer. Numerical wall shear stress for airfoil spacers is uniformly distributed and has a higher magnitude than the COM spacer. A-30 spacer design is the most efficient in ultrafiltration process with enhanced permeate flux (228%) and reduced specific energy consumption (23%) and biofouling development (74%) as characterized by Optical Coherence Tomography. Results systematically demonstrate the influential role of airfoil-shaped filaments for feed spacer design. Modifying AOA allows localized hydrodynamics to be effectively controlled according to the filtration type and operating conditions.

Monitoring residual fouling after cleaning of multi-fiber membrane modules fiber-by-fiber using non-invasive MRI monitoring.

In this study non-invasive low field magnetic resonance imaging (MRI) technology was used to monitor fouling induced changes in fiber-by-fiber hydrodynamics inside a multi-fiber hollow fiber membrane module containing 401 fibers. Using structural and velocity images the fouling evolution of these membrane modules were shown to exhibit distinct trends in fiber-by-fiber volumetric flow, with increasing fouling causing a decrease in the number of flow active fibers. This study shows that the fouling rate is not evenly distributed over the parallel fibers, which results in a broadening of the fiber to fiber flowrate distribution. During cleaning, this distribution is initially broadened further, as relatively clean fibers are cleaned more rapidly compared to clogged fibers. By tracking the volumetric flow rate of individual fibers inside the modules during the fouling-cleaning cycle it was possible to observe a fouling memory-like effect with residual fouling occurring preferentially at the outer edge of the fiber bundle during repeated fouling-cleaning cycle. These results demonstrate the ability of MRI velocity imaging to quantitatively monitor these effects which are important when testing the effectiveness of cleaning protocols due to the long term effect that residual fouling and memory-like effect may have on the operation of membrane modules.

Systemic effects of nanoplastics on multi-organ at the environmentally relevant dose: The insights in physiological, histological, and oxidative damages.

Nanoplastics (NPs) are ubiquitous contaminants that have adverse effects on human health. Previous research has explored the toxicity of NPs on specific organs at high doses, but this is insufficient for accurate health risk assessments. In the present study, a systematic study of NPs toxicity in the liver, kidney, and intestine was performed on mice at an equivalent dose of potential human exposure and toxic dose for four weeks. The results revealed that NPs penetrated the intestinal barrier and accumulated in various organs including liver, kidney, and intestine via the clathrin-mediated endocytosis, phagocytosis, and paracellular pathways. At the toxic dose, damage scores on physiology, morphology, and redox balance were more than twice that at the environmentally relevant dose, which was dose-depended. The jejunum experienced the most severe damage compared to the liver and kidney. In addition, a significant correlation between biomarkers was found, such as TNF-α and cholinesterase levels, indicating a close connection between the intestine and liver. Remarkably, the NPs exposed mice had an approximate double reactive oxygen species content compared to the control. This study promotes comprehensive understanding of health risks caused by NPs throughout the body and informs future policies and regulations to mitigate NPs-related health concerns.

The microbial growth potential of antiscalants used in seawater desalination.

20 years since the first report on the biofouling potential of chemicals used for scale control, still, antiscalants with high bacterial growth potential are used in practice. Evaluating the bacterial growth potential of commercially available antiscalants is therefore essential for a rational selection of these chemicals. Previous antiscalant growth potential tests were conducted in drinking water or seawater inoculated with model bacterial species which do not represent natural bacterial communities. To reflect better on the conditions of desalination systems, we investigated the bacterial growth potential of eight different antiscalants in natural seawater and an autochthonous bacterial population as inoculum. The antiscalants differed strongly in their bacterial growth potential varying from ≤ 1 to 6 µg easily biodegradable C equivalents/mg antiscalant. The six phosphonate-based antiscalants investigated showed a broad range of growth potential, which depended on their chemical composition, whilst the biopolymer and the synthetic carboxylated polymers-based antiscalants showed limited or no significant bacterial growth. Moreover, nuclear magnetic resonance (NMR) scans enabled antiscalant fingerprinting, identifying components and contaminants, providing a rapid and sensitive characterization, and opening opportunities for rational selection of antiscalants for biofouling control.

Periodic fouling control strategies in gravity-driven membrane bioreactors (GD-MBRs): Impact on treatment performance and membrane fouling properties.

This study aims to assess the effects of periodic membrane fouling control strategies in Gravity-Driven Membrane Bioreactor (GD-MBR) treating primary wastewater. The impact of each control strategy on the reactor performance (permeate flux and water quality), biomass morphology, and fouling composition were evaluated. The application of air scouring coupled with intermittent filtration resulted in the highest permeate flux (4 LMH) compared to only intermittent filtration (i.e., relaxation) (1 LMH) and air scouring under continuous filtration (2.5 LMH). Air scouring coupled with relaxation led to a thin (~50 µm) but with more porous fouling layer and low hydraulic resistance, presenting the lowest concentration of extracellular polymeric substance (EPS) in the biomass. Air scouring under continuous filtration led to a thin (~50 µm), dense, compact, and less porous fouling layer with the highest specific hydraulic resistance. The employment of only relaxation led to the highest fouling formation (~280 µm) on the membrane surface. The highest TN removal (~62%) was achieved in the reactor with only relaxation (no aeration) due to the anoxic condition in the filtration tank, while the highest COD removal (~ 60%) was achieved with air scouring under continuous filtration due to the longer aeration time and the denser fouling layer. The results highlighted the importance of performing in-depth fouling characterization to link the membrane fouling properties to the hydraulic resistance and membrane bioreactor performances (i.e., water quality and water production). Moreover, this work proven the versatility of the GD-MBR, where the choice of the appropriate operation and fouling control strategy relies on the eventual discharge or reuse of the treated effluent.

A sacrificial protective layer as fouling control strategy for nanofiltration in water treatment.

High-performance nanofiltration (NF) membrane with super antifouling capability as well as reusability is highly desired in water treatment. A new antifouling strategy by a coating-decoating-recoating cycle was investigated for effective removal of fouling and restoring the original membrane performance. The functional membrane surface was fabricated by in-situ coating a 'green' and biodegradable carboxymethyl chitosan (CMCS) layer as physical barrier. The CMCS layer can be decoated and re-coated by simple procedures. Results showed that (i) the CMCS layer enhanced surface hydrophilicity, surface smoothness and fouling resistance of NF membrane, (ii) both the unfouled and fouled CMCS layer were easily decoated by the strong acid solution, (iii) the CMCS layer was easily re-coated by facile recoating and (iv) the water flux recovery ratio of membrane with coating layer was maintained more than 88.8% during fouling testing by natural organic matter (NOM) after four sequential cycles of coating, decoating and recoating process. The re-coated membrane exhibited stable, improved membrane operational and antifouling performance. The coating-decoating-recoating approach is proven to be low-cost and eco-friendly strategy for NOM fouling control on NF membrane in water treatment applications.

Permeation Increases Biofilm Development in Nanofiltration Membranes Operated with Varying Feed Water Phosphorous Concentrations.

Nutrient limitation has been proposed as a biofouling control strategy for membrane systems. However, the impact of permeation on biofilm development under phosphorus-limited and enriched conditions is poorly understood. This study analyzed biofilm development in membrane fouling simulators (MFSs) with and without permeation supplied with water varying dosed phosphorus concentrations (0 and 25 µg P·L-1). The MFSs operated under permeation conditions were run at a constant flux of 15.6 L·m2·h-1 for 4.7 days. Feed channel pressure drop, transmembrane pressure, and flux were used as performance indicators. Optical coherence tomography (OCT) images and biomass quantification were used to analyze the developed biofilms. The total phosphorus concentration that accumulated on the membrane and spacer was quantified by using microwave digestion and inductively coupled plasma atomic emission spectroscopy (ICP-OES). Results show that permeation impacts biofilm development depending on nutrient condition with a stronger impact at low P concentration (pressure drop increase: 282%; flux decline: 11%) compared to a higher P condition (pressure drop increase: 206%; flux decline: 2%). The biofilm that developed at 0 µg P·L-1 under permeation conditions resulted in a higher performance decline due to biofilm localization and spread in the MFS. A thicker biofilm developed on the membrane for biofilms grown at 0 µg P·L-1 under permeation conditions, causing a stronger effect on flux decline (11%) compared to non-permeation conditions (5%). The difference in the biofilm thickness on the membrane was attributed to a higher phosphorus concentration in the membrane biofilm under permeation conditions. Permeation has an impact on biofilm development and, therefore, should not be excluded in biofouling studies.

Effects of nano- and microplastics on kidney: Physicochemical properties, bioaccumulation, oxidative stress and immunoreaction.

The potential toxicity of nanoplastics (NPs) and microplastics (MPs) has raised concerns. However, knowledge of the effects of NPs/MPs on the health of mammals is still limited. Here we investigated the alteration of the physicochemical properties of polystyrene NPs (PS-NPs: 50 nm) and MPs (PS-MPs: 300 nm, 600 nm, 4 µm) in the gastrointestinal tract. Moreover, we investigated the uptake and bioaccumulation and the toxic effects of these plastic particles in the kidneys of mice. The results revealed that their digestion promoted the aggregation of PS-NPs and PS-MPs and increased the Zeta-potential value. Both PS-NPs and PS-MPs bioaccumulated in the kidneys, and the aggregation of 600 nm PS-MPs exacerbated their biotoxicity. The PS-NPs and PS-MPs caused mice weight loss, increased their death rate, significantly alternated several biomarkers, and resulted in histological damage of the kidney. We also found that exposure to PS-NPs and PS-MPs induced oxidative stress and the development of inflammation. These findings provide new insights into the toxic effects of NPs and MPs on mice.

Seawater Reverse Osmosis Performance Decline Caused by Short-Term Elevated Feed Water Temperature.

The shortage of fresh water resources has made the desalination of seawater a widely adopted technology. Seawater reverse osmosis (SWRO) is the most commonly used method for desalination. The SWRO process is energy-intensive, and most of the energy in SWRO is spent on pressurizing the seawater to overcome the osmotic barrier for producing fresh water. The pressure needed depends on the salinity of the seawater, its temperature, and the membrane surface properties. Membrane compaction occurs in SWRO due to hydraulic pressure application for long-term operations and operating temperature fluctuations due to seasonal seawater changes. This study investigates the effects of short-term feed water temperature increase on the SWRO process in a full-scale pilot with pretreatment and a SWRO installation consisting of a pressure vessel which contains seven industrial-scale 8" diameter spiral wound membrane elements. A SWRO feed water temperature of 40 °C, even for a short period of 7 days, caused a permanent performance decline illustrated by a strong specific energy consumption increase of 7.5%. This study highlights the need for membrane manufacturer data that account for the water temperature effect on membrane performance over a broad temperature range. There is a need to develop new membranes that are more tolerant to temperature fluctuations.

Elucidating biofouling over thermal and spatial gradients in seawater membrane distillation in hot climatic conditions.

Biofouling is a hurdle of seawater desalination that increases water costs and energy consumption. In membrane distillation (MD), biofouling development is complicated due to the temperature effect that adversely affects microbial growth. Given the high relevance of MD to regions with abundant warm seawater, it is essential to explore the biofouling propensity of microbial communities with higher tolerance to elevated temperature conditions. This study presents a comprehensive analysis of the spatial and temporal biofilm distribution and associated membrane fouling during direct contact MD (DCMD) of the Red Sea water. We found that structure and composition of the biofilm layer played a significant role in the extent of permeate flux decline, and biofilms that built up at 45°C had lower bacterial concentration but higher extracellular polymeric substances (EPS) content as compared to biofilms that formed at 55 °C and 65°C. Pore wetting and bacterial passage to the permeate side were initially observed but slowed down as operating time increased. Intact cells in biofilms dominated over the damaged cells at any tested condition emphasizing the high adaptivity of the Red Sea microbial communities to elevated feed temperatures. A comparison of microbial abundance revealed a difference in bacterial distribution between the feed and biofilm samples. A shift in the biofilm microbial community and colonization of the membrane surface with thermophilic bacteria with the feed temperature increase was observed. The results of this study improve our understanding of biofouling propensity in MD that utilizes temperature-resilient feed waters.