Preparation and characteristics analysis of an ecoenvironmental protection cyclic solidification dust-fixing agent extracted from waste shrimp shells to suppress dust in coal resource-based cities.

There are a lot of coal cinder and dust in the development of coal resource-based cities. Improper handling will cause dust flying, which has a great impact on urban residents and the environment. The purpose of this research is to follow the principle of waste recycling, to use waste shrimp shells to extract chitosan as a raw material, to carry out graft polymerization with acrylic acid and polyvinyl alcohol-1788, and to carry out amidation crosslinking reactions with ethylenediamine tetraacetic acid to produce products. The results showed that the degree of deacetylation of chitosan reached 85% with the optimized extraction method, which greatly shortened the process cycle. Through orthogonal experiments and osmotic wetting experiments, the best preparation process was determined. The reaction process, structure of the product and adhesive structure of the solidified layer were analyzed by FTIR, XPS and SEM. The thermal stability of the product was analyzed by thermogravimetry. Relevant performance tests showed that the product had good adhesion with dust, the hardness of the solidified layer could reach 98 HA, and the dust fixation rate was 92.67% when the wind speed was 15-18 m/s. It has the advantage of circulating dust fixation, which improves the utilization rate of resources.

Bio-inspired gradient poly(lactic acid) nanofibers for active capturing of PM0.3 and real-time respiratory monitoring.

The concept of bio-inspired gradient hierarchies, in which the well-defined MOF nanocrystals serve as active nanodielectrics to create electroactive shell at poly(lactic acid) (PLA) nanofibers, is introduced to promote the surface activity and electroactivity of PLA nanofibrous membranes (NFMs). The strategy enabled significant refinement of PLA nanofibers during coaxial electrospinning (∼40 % decline of fiber diameter), accompanied by remarkable increase of specific surface area (nearly 1.5 m2/g), porosity (approximately 85 %) and dielectric constants for the bio-inspired gradient PLA (BG-PLA) NFMs. It largely boosted initial electret properties and electrostatic adsorption capability of BG-PLA NFMs, as well as charge regeneration by TENG mechanisms even under high-humidity environment. The BG-PLA NFMs thus featured exceptionally high PM0.3 filtration efficiencies with well-controlled air resistance (94.3 %, 163.4 Pa, 85 L/min), in contrast to the relatively low efficiency of only 80.0 % for normal PLA. During the application evaluation of outdoor air purification, excellent long-term filtering performance was demonstrated for the BG-PLA for up to 4 h (nearly 98.0 %, 53 Pa), whereas normal PLA exhibited a gradually declined filtration efficiency and an increased pressure drop. Moreover, the BG-PLA NFMs of increased electroactivity were ready to generate tribo-output currents as driven by respiratory vibrations, which enabled real-time monitoring of electrophysiological signals. This bio-inspired gradient strategy opens up promising pathways to engender biodegradable nanofibers of high surface activity and electroactivity, which has significant implications for intelligent protective membranes.

Biodegradable Electroactive Nanofibrous Air Filters for Long-Term Respiratory Healthcare and Self-Powered Monitoring.

The concept of triboelectric nanogenerator (TENG)-based fibrous air filters, in which the electroactive fibers are ready to enhance the electrostatic adsorption by sustainable energy harvesting, is appealing for long-term respiratory protection and in vivo real-time monitoring. This effort discloses a self-reinforcing electroactivity strategy to confer extreme alignment and refinement of the electrospun poly(lactic acid) (PLA) nanofibers, significantly facilitating formation of electroactive phases (i.e., ß-phase and highly aligned chains and dipoles) and promotion of polarization and electret properties. It endowed the PLA nanofibrous membranes (NFMs) with largely increased surface potential and filtration performance, as exemplified by efficient removal of PM0.3 and PM2.5 (90.68 and 99.82%, respectively) even at the highest airflow capacity of 85 L/min. With high electroactivity and a well-controlled morphology, the PLA NFMs exhibited superior TENG properties triggered by regular respiratory vibrations, enabling 9.21-fold increase of surface potential (-1.43 kV) and nearly 68% increase of PM0.3 capturing (94.3%) compared to those of conventional PLA membranes. The remarkable TENG mechanisms were examined to elaborately monitor the personal respiration characteristics, particularly those triggered large and rapid variations of output voltages like coughing and tachypnea. Featuring desirable biocompatibility and degradability, the self-powered PLA NFMs permit promising applications in the fabrication of ecofriendly air filters toward high-performance purification and intelligent monitoring.

Biodegradable MOFilters for Effective Air Filtration and Sterilization by Coupling MOF Functionalization and Mechanical Polarization of Fibrous Poly(lactic acid).

High-performance air filtration materials are important for addressing the airborne pollutants. Herein, we propose an unprecedented access to biodegradable poly(lactic acid) (PLA)-based MOFilters with excellent filtering performance and antibacterial activity. The fabrication involved a stepwise in situ growth of zeolitic imidazolate framework-8 (ZIF-8) crystals at the surface of microfibrous PLA membranes, followed by mechanical polarization under high pressure and low temperature (5 MPa, 40 °C) to trigger the ordered alignment of dipoles in PLA chains and ZIF-8. The unique structural features allowed these PLA-based MOFilters to achieve an exceptional combination of excellent tensile properties, high dielectric constant (up to 2.4 F/m), and enhanced surface potential as high as 4 kV. Arising from the remarkable surface activity and electrostatic adsorption effect, a significant increase (from over 12% to nearly 20%) in PM0.3 filtration efficiency was observed for the PLA-based MOFilters compared to that of pure PLA counterparts, with weak relation to the airflow velocities (10-85 L/min). Moreover, the air resistance was controlled at a considerably low level for all the MOFilters, that is, below 183 Pa even at 85 L/min. It is worth noting that distinct antibacterial properties were achieved for the MOFilters, as illustrated by the inhibitive rates of 87 and 100% against Escherichia coli and Staphylococcus aureus, respectively. The proposed concept of PLA-based MOFilters offers unprecedented multifunction integration, which may fuel the development of biodegradable versatile filters with high capturing and antibacterial performances yet desirable manufacturing feasibility.

Bioelectrets in Electrospun Bimodal Poly(lactic acid) Fibers: Realization of Multiple Mechanisms for Efficient and Long-Term Filtration of Fine PMs.

Despite the great potential in fabrication of biodegradable and eco-friendly air filters by electrospinning poly(lactic acid) (PLA) membranes, the filtering performance is frequently dwarfed by inadequate physical sieving or electrostatic adsorption mechanisms to capture airborne particulate matters (PMs). Here, using the parallel spinning approach, the unique micro/nanoscale architecture was established by conjugation of neighboring PLA nanofibers, creating bimodal fibers in electrospun PLA membranes for the enhanced slip effect to significantly reduce the air resistance. Moreover, the bone-like nanocrystalline hydroxyapatite bioelectret (HABE) was exploited to enhance the dielectric and polarization properties of electrospun PLA, accompanied by the controlled generation of junctions induced by the microaggregation of HABE (10-30 wt %). The incorporated HABE was supposed to orderly align in the applied E-field and largely promote the charging capability and surface potential, gradually increasing to 7.2 kV from the lowest level of 2.5 kV for pure PLA. This was mainly attributed to HABE-induced orientation of PLA backbone chains and C═O dipoles, as well as the interfacial charges trapped at the interphases of HABE-PLA and crystalline region-amorphous PLA. Given the multiple capturing mechanisms, the micro/nanostructured PLA/HABE membranes were characterized by excellent and sustainable filtering performance, e.g., the filtration efficiency of PM0.3 was promoted from 59.38% for pure PLA to 94.38% after addition of 30 wt % HABE at a moderate airflow capacity of 32 L/min and from 30.78 to 83.75% at the highest level of 85 L/min. It is of interest that the pressure drop was significantly decreased, mainly arising from the slip effect between the ultrafine nanofibers and conjugated microfibers. The proposed combination of the nanostructured electret and the multistructuring strategy offers the function integration of efficient filtration and low resistance that are highly useful to pursue fully biodegradable filters.

Preparation and performance characteristics of an environmentally-friendly agglomerant to improve the dry dust removal effect for filter material.

The incomplete and uneven dust removal of a pulse filter greatly reduces the dust removal efficiency, which affects the efficiency, service life, and running resistance of dust removers. Therefore, due to improve the pulse cleaning effect, an agglomerant developed by free radical polymerization was added during dust removal. The optimal process conditions were determined by measuring the viscosity, surface tension, and atomization effect of the agglomerant solution. The phases, chemical composition, surface morphology, and morphology of the agglomerant and coal dust were characterized by infrared spectroscopy, X-ray photoelectron spectroscopy, transmission electron microscopy, and scanning electron microscopy. Molecular dynamics simulations were used to study the interaction mechanism between the agglomerant and coal dust. Finally, the dust removal performance under water mist conditions and agglomerate solution atomization was tested using a pulse filter. The results showed that a 0.3 % agglomerant solution effectively reduced the surface tension of the solution and displayed good wetting and bonding properties. Compared with water misting, the agglomerant solution subjected to an atomization rate of 2400 m3/h prolonged the filtration period, reduced the filtration resistance, and reduced the dust emission concentration. These results have important theoretical and practical significance for improving the dust removal effect of pulse filters.