A low-cost and hand-hold PCR microdevice based on water-cooling technology.

Polymerase chain reaction (PCR) has become a powerful tool for detecting various diseases due to its high sensitivity and specificity. However, the long thermocycling time and the bulky system have limited the application of PCR devices in Point-of-care testing. Herein, we have proposed an efficient, low-cost, and hand-hold PCR microdevice, mainly including a control module based on water-cooling technology and an amplification module fabricated by 3D printing. The whole device is tiny and can be easily hand-held with a size of about 110 mm × 100 mm × 40 mm and a weight of about 300 g at a low cost of about $170.83. Based on the water-cooling technology, the device can efficiently perform 30 thermal cycles within 46 min at a heating/cooling rate of 4.0/8.1 ℃/s. To test our instrument, plasmid DNA dilutions were amplified with this device; the results demonstrate successful nucleic acid amplification of the plasmid DNA and exhibit the promise of this device for Point-of-care testing.

A meta-analysis of semiconductor materials fabricated in microgravity.

This meta-analysis of 160 semiconductor crystals that were grown in microgravity on orbital vehicles between 1973 and 2016 is based on publicly available information documented in the literature. This analysis provides comparisons of crystal metrics including size, structure quality, uniformity, and improved performance between crystals grown in microgravity or terrestrially. Improvement in at least one of these metrics was observed for 86% of those materials that included data in their studies.

Dissolving and Swelling Hydrogel-Based Microneedles: An Overview of Their Materials, Fabrication, Characterization Methods, and Challenges.

Polymeric hydrogels are a complex class of materials with one common feature-the ability to form three-dimensional networks capable of imbibing large amounts of water or biological fluids without being dissolved, acting as self-sustained containers for various purposes, including pharmaceutical and biomedical applications. Transdermal pharmaceutical microneedles are a pain-free drug delivery system that continues on the path to widespread adoption-regulatory guidelines are on the horizon, and investments in the field continue to grow annually. Recently, hydrogels have generated interest in the field of transdermal microneedles due to their tunable properties, allowing them to be exploited as delivery systems and extraction tools. As hydrogel microneedles are a new emerging technology, their fabrication faces various challenges that must be resolved for them to redeem themselves as a viable pharmaceutical option. This article discusses hydrogel microneedles from a material perspective, regardless of their mechanism of action. It cites the recent advances in their formulation, presents relevant fabrication and characterization methods, and discusses manufacturing and regulatory challenges facing these emerging technologies before their approval.

Blister Formation in Film Insert Moulding.

The formation of blister in the injection moulded parts, especially in the film insert moulded parts, is one of most significant causes of part rejection due to cosmetic requirements or functionality issues. The mechanism and physics of blister formation for molded parts are not well-understood by the state-of-the-art literature. The current paper increases the fundamental understanding of the causes for blister formation. In the experiment, a membrane strip of 5 mm in width was overmoulded with Polypropylene (PP), which formed a disc-shaped part with a diameter of 17.25 mm and a thickness of 500 µm. To investigate the influence of the processing parameters, a full factorial design of experiments (DoE) setup was conducted, including mould temperature (Tm), barrel temperature (Tb), injection speed (Vi) and packing pressure (Pp) as variables. The degree of blistering at the surface was characterized by the areal surface roughness parameters Spk and Smr1, measured with a confocal laser microscope. The measurements were taken on the 10 mm long section of the membrane surface in the centre of the moulded part across the entire width of the film. In addition, the film insert moulding (FIM)-process was simulated and the average shrinkage of the substrate material under the membrane was investigated. Eventually, a method and processing window could be defined that could produce blister-free parts.

Crystallization Temperature Dependence of Cavitation and Plastic Flow in the Tensile Deformation of Poly(ε-caprolactone).

In situ small-, ultrasmall-, and wide-angle X-ray scattering measurements were performed to investigate the structural evolution of crystalline lamellae and cavities as a function of deformation ratio during tensile deformation of isothermally crystallized poly(ε-caprolactone). The cavities were modeled as cylinder-shaped objects which are oriented along the stretching direction and randomly distributed in the samples, and their dimensions were evaluated by direct model fitting of scattering patterns. At small deformations, the orientation of these cavities at the onset of cavity formation was related to the isothermal crystallization temperature. Upon further stretching, the cavities were found to cluster in the interfibrillar regions at moderate strains where the long spacing of the newly developed lamellae along the stretching direction remained essentially constant. At large orientations, the cooperative deformational behavior mediated via slippage of fibrils was evidenced, the extent of which depended on the cavity number, which could be traced back to the significantly different coupling forces imposed by chains connecting adjacent fibrils. Furthermore, wide-angle X-ray scattering results revealed that a fraction of the polymer chains with their orientation perpendicular to the stretching direction were still preserved even at large macroscopic strains.