Experimental and Numerical Studies on Hot Compressive Deformation Behavior of a Cu-Ni-Sn-Mn-Zn Alloy.

Cu-9Ni-6Sn alloys have received widespread attention due to their good mechanical properties and resistance to stress relaxation in the electronic and electrical industries. The hot compression deformation behaviors of the Cu-9Ni-6Sn-0.3Mn-0.2Zn alloy were investigated using the Gleeble-3500 thermal simulator at a temperature range of 700-900 °C and a strain rate range of 0.001-1 s-1. The microstructural evolution of the Cu-9Ni-6Sn alloy during hot compression was studied by means of an optical microscope and a scanning electron microscope. The constitutive equation of hot compression of the alloy was constructed by peak flow stress, and the corresponding 3D hot processing maps were plotted. The results showed that the peak flow stress decreased with the increase in the compression temperature and the decrease in the strain rate. The hot deformation activation energy was calculated as 243.67 kJ/mol by the Arrhenius equation, and the optimum deformation parameters for the alloy were 740-760 °C and 840-900 °C with a strain rate of 0.001~0.01 s-1. According to Deform-3D finite element simulation results, the distribution of the equivalent strain field in the hot deformation samples was inhomogeneous. The alloy was more sensitive to the deformation rate than to the temperature. The simulation results can provide a guideline for the optimization of the microstructure and hot deformation parameters of the Cu-9Ni-6Sn-0.3Mn-0.2Zn alloy.

Correction: Zhang et al. Experimental and Numerical Studies on Hot Compressive Deformation Behavior of a Cu-Ni-Sn-Mn-Zn Alloy. Materials 2023, 16, 1445.

In the original publication [...].

Effect of C Addition on the Microstructure and Fracture Properties of In Situ Laminated Nb/Nb5Si3 Composites.

//Nbss and α-Nb5Si3 phases were detected. Meanwhile, Nb2C was observed, and the crystal forms of Nb5Si3 changed in the C-doped composites. Furthermore, micron-sized and nano-sized Nb2C particles were found in the Nbss layer. The orientation relationship of Nb2C phase and the surrounding Nbss was [001]Nbss//[010]Nb2C, (200) Nbss//(101) Nb2C. Additionally, with the addition of C, the compressive strength of the composites, at 1400 °C, and the fracture toughness increased from 310 MPa and 11.9 MPa·m1/2 to 330 MPa and 14.2 MPa·m1/2, respectively; the addition of C mainly resulted in solid solution strengthening.

Orthogonal Experimental Optimization of Preparation and Microstructural Properties of a Diffusion Barrier for Tantalum-Based Silicide Coatings.

To solve the problem of silicide coatings on tantalum substrates failing due to elemental diffusion under high-temperature oxidation environments and to find diffusion barrier materials with excellent effects of impeding Si elemental spreading, TaB2 and TaC coatings were prepared on tantalum substrates by the encapsulation and infiltration methods, respectively. Through orthogonal experimental analysis of the raw material powder ratio and pack cementation temperature, the best experimental parameters for the preparation of TaB2 coatings were selected: powder ratio (NaF:B:Al2O3 = 2.5:1:96.5 (wt.%)) and pack cementation temperature (1050 °C). After diffusion treatment at 1200 °C for 2 h, the thickness change rate of the Si diffusion layer prepared using this process was 30.48%, which is lower than that of non-diffusion coating (36.39%). In addition, the physical and tissue morphological changes of TaC and TaB2 coatings after siliconizing treatment and thermal diffusion treatment were compared. The results prove that TaB2 is a more suitable candidate material for the diffusion barrier layer of silicide coatings on tantalum substrates.

Microstructure and Mechanical Properties of Cast Al-Si-Cu-Mg-Ni-Cr Alloys: Effects of Time and Temperature on Two-Stage Solution Treatment and Ageing.

Ameliorating the high-temperature performance of cast Al-Si alloys used as engine components is essential. The effects of different T6 heat-treatment processes on the microstructure and mechanical properties of cast Al-Si-Cu-Mg-Ni-Cr alloys were investigated in the present study. The results demonstrate that, under the optimal solution treatment conditions of 500 °C for 2 h and 540 °C for 4 h, the T-Al9FeNi phase was present in the alloy, and the roundness of primary Si and the aspect ratio of eutectic Si in the alloy reached valley values of 1.46 and 2.56, respectively. With increasing ageing time at 180 °C, the tensile strength significantly improved, while the microhardness first increased and then decreased. When the ageing time was 4 h, microhardness reached a peak value of 155.82 HV. The fracture characteristics changed from quasi-cleavage to the coexistence of quasi-cleavage and dimples. After heat treatment, the high-temperature tensile properties of the alloy improved, which is a significant advantage compared to the as-cast alloy. The stable Al3Ni and Al9FeNi phases inhibited the cracking of the alloy at 350 °C.

Microstructure and Wear Behavior of Ti-xFe-SiC In Situ Composite Ceramic Coatings on TC4 Substrate from Laser Cladding.

Titanium alloys are widely used in various structural materials due to their lightweight properties. However, the low wear resistance causes significant economic losses every year. Therefore, it is necessary to implement wear-resistant protection on the surface of titanium alloys. In this study, four types of in situ composite ceramic coatings with two-layer gradient structures were prepared on a Ti-6Al-4V (TC4) substrate using laser cladding. In order to reduce the dilution rate, a transition layer (Ti-40SiC (vol.%)) was first prepared on TC4 alloy. Then, a high-volume-fraction in situ composite ceramic working layer (Ti-xFe-80SiC (vol.%)) with different contents of Fe-based alloy powder (x = 0, 5, 10 and 15 vol.%) was prepared. The working surface of Ti-40SiC (TL) exhibited a typical XRD pattern of Ti, TiC, Ti5Si3, and Ti3SiC2. In comparison, both Ti-80SiC (WL-F0) and Ti-5Fe-80SiC (WL-F5) exhibited similar phase compositions to the TL coating, with no new phase identified in the coatings. However, the TiFeSi2 and SiC phases were presented in Ti-10Fe-80SiC (WL-F10) and Ti-15Fe-80SiC (WL-F15). It is proven that the addition of the Fe element could regulate the in situ reaction in the original Ti-Si-C ternary system to form the new phases with high hardness and good wear resistance. The hardness of the WL-F15 (1842.9 HV1) is five times higher than that of the matrix (350 HV1). Due to the existence of self-lubricating phases such as Ti5Si3 and Ti3SiC2, a lubricating film was presented in the WL-F0 and WL-F5 coatings, which could block the further damage of the friction pair and enhance the wear resistance. Furthermore, a wear-transition phenomenon was observed in the WL-F10 and WL-F15 coatings, which was similar to the friction behavior of structural ceramics. Under the load of 10 N and 20 N, the wear volume of WL-F15 coating is 5.2% and 63.7% of that in the substrate, and the depth of friction of WL-15 coating is only 14.4% and 80% of that in the substrate. The transition of wear volume and depth can be attributed to the wear mechanism changing from oxidation wear to adhesive wear.

A Novel Superhard, Wear-Resistant, and Highly Conductive Cu-MoSi2 Coating Fabricated by High-Speed Laser Cladding Technique.

The pursuit of an advanced functional coating that simultaneously combines high hardness, wear resistance, and superior electrical conductivity has remained an elusive goal in the field of copper alloy surface enhancement. Traditional solid solution alloying methods often lead to a significant increase in electron scattering, resulting in a notable reduction in electrical conductivity, making it challenging to achieve a balance between high hardness, wear resistance, and high conductivity. The key lies in identifying a suitable microstructure where dislocation motion is effectively hindered while minimizing the scattering of conductive electrons. In this study, a novel Cu-MoSi2 coating was successfully fabricated on a CuCrZr alloy surface using the coaxial powder feeding high-speed laser cladding technique, with the addition of 10-30% MoSi2 particles. The coating significantly enhances the hardness and wear resistance of the copper substrate while maintaining favorable electrical conductivity. As the quantity of MoSi2 particles increases, the coating's hardness and wear resistance gradually improve, with minimal variance in conductivity. Among the coatings, the Cu-30%MoSi2 coating stands out with the highest hardness (974.5 HV0.5) and the lowest wear amount (0.062 mg/km), approximately 15 times the hardness of the copper base material (65 HV0.5) and only 0.45% of the wear amount (13.71 mg/km). Additionally, the coating exhibits a resistivity of 0.173 × 10-6 Ω·m. The extraordinary hardness and wear resistance of these coatings can be attributed to the dispersion strengthening effect of MoxSiy particles, while the high electrical conductivity is due to the low silicon content dissolved into the copper from the released MoSi2 particles, as well as the rapid cooling rates associated with the high-speed laser cladding process.

The thermodynamic stability and mechanical properties of TiCxN1-x(0⩽x⩽ 1) compounds by cluster expansion method and first-principles calculations.

The thermodynamic stability and mechanical properties of titanium carbonitrides TiCxN1-x(0 ⩽x⩽ 1) are investigated by a combination of the universal cluster expansion method and the first-principles calculations. By considering the ordering of the N/C distributions on the anion sublattice sites of TiCxN1-x, a binary diagram of the heat of formation is constructed, and seven kinds of ground-state structures are predicted in the whole range of 0 ⩽x⩽ 1. These predicted ground-state TiCxN1-xstructures are further proved to be dynamically and mechanically stable by examining their phonon dispersion spectra and elastic constants. Further studies indicate that the mechanical and thermodynamic properties of the ternary TiCxN1-xstructures are generally better than those of the binary TiC or TiN, while the differences within the ternary systems are insignificant. The possible origin of the enhancement of the mechanical and thermodynamic properties of the predicted ground-state TiCxN1-xare discussed together with the electronic structures.