RESUMO
All-solid-state lithium batteries (ASSLBs) are prepared using garnet-type solid electrolytes by quick liquid phase sintering (Q-LPS) without applying high pressure during the sintering. The cathode layers are quickly sintered with a heating rate of 50-100 K min-1 and a dwell time of 10 min. The battery performance is dramatically improved by simultaneously optimizing materials, processes, and architectures, and the initial discharge capacity of the cell with a LiCoO2 -loading of 8.1 mg reaches 1 mAh cm-2 and 130 mAh g-1 at 25 °C. The all-solid-state cell exhibits capacity at a reduced temperature (10 °C) or a relatively high rate (0.1 C) compared to the previous reports. The Q-LPS would be suitable for large-scale manufacturing of ASSLBs. The multiphysics analyses indicate that the internal stress reaches 1 GPa during charge/discharge, which would induce several mechanical failures of the cells: broken electron networks, broken ion networks, separation of interfaces, and delamination of layers. The experimental results also support these failures.
RESUMO
Chemical stability of garnet-type lithium ion conductors is one of the critical issues in their application in all-solid-state batteries. Here, we conducted quantitative analysis of impurity layers on the garnet-type solid electrolytes, Li6.5La3-xAExZr1.5-xTa0.5+xO12 (x = 0 and 0.1; AE = Ca, Sr, and Ba), by means of X-ray photoelectron spectroscopy (XPS) and electrochemical methods. Two complimentary XPS techniques were employed: (i) background analyses by Tougaard's method and (ii) relative intensity analyses of La 3d/La 4d spectra to determine the surface chemical composition. XPS revealed that even after cleaning by annealing and polishing, the surface is covered by LiOH- and Li2CO3-based compounds with a thickness of 4-6 nm within 30 min as a result of the reaction with traces of H2O (<0.5 ppm) and CO2 (<5 ppm) in an Ar-filled glovebox. The sensitivity to H2O and CO2 depends on the basicity of dopants. Ba-doped solid electrolytes exhibited the thickest impurity layers compared to Sr- and Ca-doped compounds. A surface cleaning process, consisting of annealing and polishing, effectively reduces the charge-transfer resistance to 10-15 Ω cm2 because of negligible impurity layers. Highest short-circuit tolerance is obtained for a 700 °C annealed specimen (critical current density: 0.5 mA cm-2), which is possibly due to the strengthened grain boundaries by Li2CO3 among grains around its melting point.
RESUMO
Relatively ordered macroporous films of a cut single-walled carbon nanotubes (c-SWNTs) assembly and a TiO 2/c-SWNTs nanocomposite were successfully fabricated by colloidal crystal template processes using polystyrene particles. The macroporous TiO2/c-SWNTs nanocomposite film showed excellent rate capability of Li-insertion/extraction. The rate-dependent Li-insertion/extraction capacities were close to theoretical values expected from Li-diffusion in anatase--TiO2 thin layer without blocking electrolyte-ion and electron access.
RESUMO
The effect of crystallite size on Li-ion insertion in electrode materials is of great interest recently because of the need for nanoelectrodes in higher-power Li-ion rechargeable batteries. We present a systematic study of the effect of size on the electrochemical properties of LiMn(2)O(4). Accurate size control of nanocrystalline LiMn(2)O(4), which is realized by a hydrothermal method, significantly alters the phase diagram as well as Li-ion insertion voltage. Nanocrystalline LiMn(2)O(4) with extremely small crystallite size of 15 nm cannot accommodate domain boundaries between Li-rich and Li-poor phases due to interface energy, and therefore lithiation proceeds via solid solution state without domain boundaries, enabling fast Li-ion insertion during the entire discharge process.