Simultaneous bond-selective deuterium-based isotopic labeling sensing with disposable ultra-miniature CARS fiber probe.

Deuterium-based isotopic labeling is an important technique for tracking cellular metabolism with the Raman signals analysis of low-wavenumber (LW) C-D bonds and high-wavenumber (HW) C-H bonds. We propose and demonstrate a disposable ultra-miniature fiber probe to detect LW and HW coherent anti-Stokes Raman scattering (CARS) spectra for deuterated compounds simultaneously and bond-selectively sensing. The 10.78 µm diameter disposable fiber probe, comprised of focusing taper as fiber probe head and time-domain walk-off eliminating fiber section with designed length, realizes wide-frequency-interval dual Stokes pulse delivering and focusing. The fiber probe enables quantitative concentration determination with resolution down to 11 mM. The chemical vibration modes of LW region C-D bonds and HW region C-H bonds of the mixture samples of organic compounds and their deuterated counterparts in a simulated cell are simultaneously excited and characterized. The CARS disposable fiber probe introduces a promising handle for in vivo biochemical detection based on isotopic labeling sensing.

Broadband phase shifter based on SiN-MoS2 integrated racetrack resonator.

As the critical device of microwave photonics and optical communication, the low-loss and high-efficiency optical phase shifter has attracted intense attention in photonic integrated circuits. However, most of their applications are restricted to a particular band. Little is known about the characteristics of broadband. In this paper, an SiN-MoS2 integrated broadband racetrack phase shifter is demonstrated. The coupling region and the structure of the racetrack resonator are elaborately designed to improve the coupling efficiency at each resonance wavelength. The ionic liquid is introduced to form a capacitor structure. Then, the effective index of the hybrid waveguide can be efficiently tuned by adjusting the bias voltage. We achieve a phase shifter with a tunable range covering all the WDM bands and even up to 1900 nm. The highest phase tuning efficiency is measured to be 72.75 pm/V at 1860 nm, and the corresponding half-wave-voltage-length product is calculated as 0.0608 V·cm.

MoS2 hybrid integrated micro-ring resonator phase shifter based on a silicon nitride platform.

We demonstrate a low-power, compact micro-ring phase shifter based on hybrid integration with atomically thin two-dimensional layered materials, and experimentally establish a low-loss silicon nitride platform. Using a wet transfer method, a large-area few-layer MoS2 film is hybrid integrated with a micro-ring phase shifter, leading to a tuning efficiency of 5.8 pm V-1 at a center wavelength of 1545.294 nm and a half-wave-voltage-length product as low as 0.09 V cm. Our device is designed to provide a hybrid-integration-based active phase modulation scheme for integrated optical communication networks with large-cross-section silicon nitride waveguides.

Few-layer metal monochalcogenide saturable absorbers for high-energy Q-switched pulse generation.

Two-dimensional layered materials have been widely utilized as nonlinear absorption materials to transfer continue-wave into pulse trains in fiber laser systems. Here, we prepare robust GaSe/GeSe composites with high power bearing capacity as saturable absorbers (SAs) and then investigate their nonlinear optical properties via broadband Z-scan measurement at 800 nm and 1550 nm, respectively. The modulation depths of GaSe/GeSe based SAs are measured to be 11.97% and 7.69% at 1550 nm. After incorporating the GaSe/GeSe SAs into an Erbium-doped fiber laser cavity, passively Q-switched pulse trains could be obtained with repetition rates changing from 83.58 to 136.78 kHz (70.41 to 161.65 kHz). The maximum output power and pulse energy are 52.1 mW/370.67 nJ (GaSe) and 21.6 mW/133.74 nJ (GeSe) under the maximum pump power of 600 mW. The results indicate that GaSe and GeSe possess outstanding thermal stability and could be employed as remarkable saturable absorption materials for high-energy pulses generation.

Ultrafast fiber laser based on HfSe2 saturable absorber.

We demonstrate the HfSe2 saturable absorber (SA) for the generation of ultrafast pulse laser. The HfSe2 SA device is fabricated by integrating HfSe2 nanosheets (NSs) with a microfiber. The material and optical characteristics of HfSe2 NSs show their high quality. The nonlinear optical absorption of HfSe2 SA is measured with a modulation depth of 5.8%. Stable soliton mode-locked laser based on HfSe2 SA is realized at the central wavelength of 1561.43 nm with pulse duration of 297 fs and the maximum pulse energy of 2.68 nJ. Our soliton fiber laser has a maximum output power of 48.5 mW with a high slope efficiency of 12.8%, which indicate that HfSe2 is a good candidate of SA for high efficient ultrashort pulses generation.

High-power mode-locked thulium-doped fiber laser with tungsten ditelluride as saturable absorber.

A passively mode-locked thulium-doped fiber laser using a tungsten ditelluride saturable absorber (${{\rm WTe}_2}\mbox{-}{\rm SA}$WTe2-SA) is demonstrated. High-power mode-locked pulses with an average output power of 108.1 mW were achieved by incorporating the ${{\rm WTe}_2}\mbox{-}{\rm SA}$WTe2-SA into a thulium-doped fiber oscillator. To the best of our knowledge, this is the highest average power obtained from a ${{\rm WTe}_2}\mbox{-}{\rm SA}$WTe2-SA-based fiber laser. We further amplified the output power to 5.60 W with an all-fiber thulium-doped double-cladding fiber amplifier. Our result indicates that ${{\rm WTe}_2}\mbox{-}{\rm SA}$WTe2-SA could be an excellent candidate for a high-power fiber laser system.

α-In2Se3 wideband optical modulator for pulsed fiber lasers.

With the magnetron-sputtering deposition method, α phase indium selenide (α-In2Se3) was developed into a saturable absorber (SA) with wideband saturable absorption property at 800, 1560, and 1930 nm. After inserting the α-In2Se3 SA into erbium-doped fiber laser (EDFL) and thulium-doped fiber laser (TDFL) systems, we can easily obtain stable soliton pulse trains. The pulse duration/pulse energy/slope efficiency for EDFL and TDFL were 276 fs/2.03 nJ/15.8% and 1.02 ps/7.1 nJ/23.5%, respectively. These results showed that the MSD-grown α-In2Se3 could be regarded as high efficiency material to be applied in ultrafast photonics.

Mode-locked thulium-doped fiber laser with chemical vapor deposited molybdenum ditelluride.

A passively mode-locked thulium-doped fiber (TDF) laser was realized by employing chemical vapor deposited few-layer molybdenum ditelluride (MoTe2) as a saturable absorber (SA). The few-layer MoTe2 film was transferred onto the waist of a microfiber and then incorporated into a TDF laser with a typical all-fiber ring cavity configuration. Stable soliton pulses emitting at 1930.22 nm were obtained with a 3 dB bandwidth of 4.45 nm, a pulse duration of 952 fs, and an average power of 36.7 mW.

Large-area highly crystalline WSe2 atomic layers for ultrafast pulsed lasers.

Large-area and highly crystalline transition metal dichalcogenides (TMDs) films possess superior saturable absorption compared to the TMDs nanosheet counterparts, which make them more suitable as excellent saturable absorbers (SA) for ultrafast laser technology. Thus far, the nonlinear optical properties of large-scale WSe2 and its applications in ultrafast photonics have not yet been fully investigated. In this work, the saturable absorption of chemical vapor deposition (CVD) grown WSe2 films with large-scale and high quality are studied and the use of WSe2 films as a broadband SA for passively mode-locked fiber lasers at both 1.5 and 2 µm ranges is demonstrated. To enhance the light-material interaction, large-area WSe2 film is tightly transferred onto the side wall of a microfiber to form a hybrid structure, which realizes strong evanescent wave interaction between light and WSe2 film. The integrated microfiber-WSe2 device shows a large modulation depth of 54.5%. Using the large-area WSe2 as a mode-locker, stable soliton mode-locked pulse generation is achieved and the pulse durations of 477 fs (at 1.5 µm) and 1.18 ps (at 2.0 µm) are demonstrated, which suggests that the large-area and highly crystalline WSe2 films afford an excellent broadband SA for ultrafast photonic applications.

Magnetron-sputtering deposited WTe2for an ultrafast thulium-doped fiber laser.

Ultrafast pulse generation was demonstrated in a thulium-doped fiber laser mode-locked by magnetron-sputtering deposited WTe2 with a modulation depth, a nonsaturable loss, and a saturable intensity of 31%, 34.3%, and 7.6 MW/cm2, respectively. Stable soliton pulses could be obtained at a 1915.5 nm central wavelength with a pulse duration of 1.25 ps, an average output power of 39.9 mW, and a signal-to-noise ratio of 95 dB. To the best of our knowledge, this was the first demonstration of WTe2-based saturable absorbers in fiber lasers at a 2 µm regime.

Transition-metal dichalcogenides heterostructure saturable absorbers for ultrafast photonics.

In this Letter, high-quality WS2 film and MoS2 film were vertically stacked on the tip of a single-mode fiber in turns to form heterostructure (WS2-MoS2-WS2)-based saturable absorbers with all-fiber integrated features. Their nonlinear saturable absorption properties were remarkable, such as a large modulation depth (∼16.99%) and a small saturable intensity (6.23 MW·cm-2). Stable pulses at 1.55 µm with duration as short as 296 fs and average power as high as 25 mW were obtained in an erbium-doped fiber laser system. The results demonstrate that the proposed heterostructures own remarkable nonlinear optical properties and offer a platform for adjusting nonlinear optical properties by stacking different transition-metal dichalcogenides or modifying the thickness of each layer, paving the way for engineering functional ultrafast photonics devices with desirable properties.

Large-area and highly crystalline MoSe2 for optical modulator.

Transition metal dichalcogenides (TMDs) have been successfully used as broadband optical modulator materials for pulsed fiber laser systems. However, the nonlinear optical absorptions of exfoliated TMDs are strongly limited by their nanoflakes morphology with uncontrollable lateral size and thickness. In this work, we provide an effective method to fully explore the nonlinear optical properties of MoSe2. Large-area and high quality lattice MoSe2 grown by chemical vapor deposition method was adopted as an optical modulator for the first time. The large-area MoSe2 shows excellent nonlinear optical absorption with a large modulation depth of 21.7% and small saturable intensity of 9.4 MW cm-2. After incorporating the MoSe2 optical modulator into fiber laser cavity as a saturable absorber, a highly stable Q-switching operation with single pulse energy of 224 nJ is achieved. The large-area MoSe2 possessing superior nonlinear optical properties compared to exfoliated nanoflakes affords possibility for the larger-area two-dimensional materials family as high performance optical devices.

High-damage-resistant tungsten disulfide saturable absorber mirror for passively Q-switched fiber laser.

In this paper, we demonstrate a high-damage-resistant tungsten disulfide saturable absorber mirror (WS2-SAM) fabricated by magnetron sputtering technique. The WS2-SAM has an all-fiber-integrated configuration and high-damage-resistant merit because the WS2 layer is protected by gold film so as to avoid being oxidized and destroyed at high pump power. Employing the WS2-SAM in an Erbium-doped fiber laser (EDFL) with linear cavity, the stable Q-switching operation is achieved at central wavelength of 1560 nm, with the repetition rates ranging from 29.5 kHz to 367.8 kHz and the pulse duration ranging from 1.269 µs to 154.9 ns. For the condition of the maximum pump power of 600 mW, the WS2-SAM still works stably with an output power of 25.2 mW, pulse energy of 68.5 nJ, and signal-noise-ratio of 42 dB. The proposed WS2-SAM configuration provides a promising solution for advanced pulsed fiber lasers with the characteristics of high damage resistance, high output energy, and wide tunable frequency.

Differential-pressure-based fiber-optic temperature sensor using Fabry-Perot interferometry.

We propose a novel fiber-optic Fabry-Perot interferometric (FFPI) temperature sensor based on differential pressure resulting from thermal expansion of sealed air. A thin silicon diaphragm is sandwiched between two micro-circular cavity-structured Pyrex plates to construct a FP and an air cavity. The thermal expansion of sealed air induces differential pressure variation between cavities and thus the deformation of thin diaphragm, which transfers temperature change into cavity length shift of FP interferometer. Theory analysis results indicate that the temperature-sensitivity can be designed flexibly by choosing the parameters of radius and thickness of silicon diaphragm, and the differential pressure between two cavities. Experimental results demonstrate that the temperature sensitivity of 6.07 nm/°C is achieved with the resolution of 0.10°C under the range of -50°C to 100°C, and the response time is around 1.3 s with temperature change from 28°C to 100°C.

Zero-fringe demodulation method based on location-dependent birefringence dispersion in polarized low-coherence interferometry.

We present a high precision and fast speed demodulation method for a polarized low-coherence interferometer with location-dependent birefringence dispersion. Based on the characteristics of location-dependent birefringence dispersion and five-step phase-shifting technology, the method accurately retrieves the peak position of zero-fringe at the central wavelength, which avoids the fringe order ambiguity. The method processes data only in the spatial domain and reduces the computational load greatly. We successfully demonstrated the effectiveness of the proposed method in an optical fiber Fabry-Perot barometric pressure sensing experiment system. Measurement precision of 0.091 kPa was realized in the pressure range of 160 kPa, and computation time was improved by 10 times compared to the traditional phase-based method that requires Fourier transform operation.

Birefringence dispersion compensation demodulation algorithm for polarized low-coherence interferometry.

A demodulation algorithm based on the birefringence dispersion characteristics for a polarized low-coherence interferometer is proposed. With the birefringence dispersion parameter taken into account, the mathematical model of the polarized low-coherence interference fringes is established and used to extract phase shift information between the measured coherence envelope center and the zero-order fringe, which eliminates the interferometric 2 π ambiguity of locating the zero-order fringe. A pressure measurement experiment using an optical fiber Fabry-Perot pressure sensor was carried out to verify the effectiveness of the proposed algorithm. The experiment result showed that the demodulation precision was 0.077 kPa in the range of 210 kPa, which was improved by 23 times compared to the traditional envelope detection method.

Wavelength-division-multiplexing method of polarized low-coherence interferometry for fiber Fabry-Perot interferometric sensors.

We propose a new wavelength-division-multiplexing method for extrinsic fiber Fabry-Perot interferometric (EFPI) sensing in a polarized low-coherence interferometer configuration. In the proposed method, multiple LED sources are used with different center wavelengths, and each LED is used by a specific sensing channel, and therefore the spatial frequency of the low-coherence interferogram of each channel can be separated. A bandpass filter is used to extract the low-coherence interferogram of each EFPI channel, and thus the cavity length of each EFPI channel can be identified through demultiplexing. We successfully demonstrate the simultaneous demodulation of EFPI sensors with same nominal cavity length while maintaining high measurement precision.

A polarized low-coherence interferometry demodulation algorithm by recovering the absolute phase of a selected monochromatic frequency.

A demodulation algorithm based on absolute phase recovery of a selected monochromatic frequency is proposed for optical fiber Fabry-Perot pressure sensing system. The algorithm uses Fourier transform to get the relative phase and intercept of the unwrapped phase-frequency linear fit curve to identify its interference-order, which are then used to recover the absolute phase. A simplified mathematical model of the polarized low-coherence interference fringes was established to illustrate the principle of the proposed algorithm. Phase unwrapping and the selection of monochromatic frequency were discussed in detail. Pressure measurement experiment was carried out to verify the effectiveness of the proposed algorithm. Results showed that the demodulation precision by our algorithm could reach up to 0.15kPa, which has been improved by 13 times comparing with phase slope based algorithm.

Recent development in graphdiyne and its derivative materials for novel biomedical applications.

Graphdiyne (GDY), which possess sp- and sp2-hybridized carbon and Dirac cones, offers unique physical and chemical properties, including an adjustable intrinsic bandgap, excellent charge carrier transfer efficiency, and superior conductivity compared to other carbon allotropes. These exceptional qualities of GDY and its derivatives have been successfully used in a variety of fields, including catalysis, energy, environmental protection, and biological applications. Herein, we focus on the potential application of GDY and its derivatives in the biomedical domain, including biosensing, biological protection, cancer therapy, and antibacterial agents, demonstrating how the biomimetic behavior of these materials can be a step forward in bridging the gap between nature and applications. Considering the excellent biocompatibility, solubility and selectivity of GDY and its derived materials, they have shown great potential as biosensing and bio-imaging materials. The unusual combination of properties in GDY has been used in biological applications such as "OFF-ON" DNA detection and enzymatic sensing, where GDY has a greater adsorption capacity than graphene and other 2D materials, resulting in increased sensitivity. GDY and its derivatives have also been used in cancer treatment due to their high doxorubicin (DOX) loading capacity (using-stacking) and photothermal conversion ability, and radiation protection since their initial biological use. The poor biodegradation rate of graphene demands the search for new nanomaterials. Accordingly, GDY has better biocompatibility and bio-safety than other 2D nanomaterials, especially graphene and its oxide, due to its absence of aggregation in the physiological environment. Thus, GDY-based nanomaterials have become promising candidates as bio-delivery carriers. Besides, GDY and GDY-based materials have also shown interesting applications in the fields of cell-culture, cell-growth and tissue engineering. Herein, we present a comprehensive review on the applications of GDY and its derivatives as biomedical materials, followed by their future perspectives. This review will provide an outlook for the application of graphene and its derivatives and may open up new horizons to inspire broader interests across various disciplines. Finally, the future prospects for GDY-based materials are examined for their potential biological use.

Tungsten diselenide for all-fiber lasers with the chemical vapor deposition method.

Two-dimensional materials have become the focus of research for their photoelectric properties, and are employed as saturable absorption materials. Currently, the challenge is how to further improve the modulation depth of saturable absorbers (SAs) based on two-dimensional materials. In this paper, three kinds of WSe2 films with different thicknesses are prepared using the chemical vapor deposition method. The nonlinear optical responses of the WSe2 films including the nonlinear saturable absorption and nonlinear refractive index are characterized by the double-balanced detection method and Z-scan experiments. Different modulation depths are successfully obtained by controlling the thickness of the WSe2 films. We further incorporate them into an all-fiber laser to generate mode-locked pulses. The mode-locked fiber lasers with a pulse duration of 185 fs, 205.7 fs and 230.3 fs are demonstrated when the thickness of the WSe2 films is measured to be 1.5 nm, 5.7 nm and 11 nm, respectively. This work provides new prospects for WSe2 in ultrafast photonic device applications.