High-speed and large-scale intrinsically stretchable integrated circuits.

Intrinsically stretchable electronics with skin-like mechanical properties have been identified as a promising platform for emerging applications ranging from continuous physiological monitoring to real-time analysis of health conditions, to closed-loop delivery of autonomous medical treatment1-7. However, current technologies could only reach electrical performance at amorphous-silicon level (that is, charge-carrier mobility of about 1 cm2 V-1 s-1), low integration scale (for example, 54 transistors per circuit) and limited functionalities8-11. Here we report high-density, intrinsically stretchable transistors and integrated circuits with high driving ability, high operation speed and large-scale integration. They were enabled by a combination of innovations in materials, fabrication process design, device engineering and circuit design. Our intrinsically stretchable transistors exhibit an average field-effect mobility of more than 20 cm2 V-1 s-1 under 100% strain, a device density of 100,000 transistors per cm2, including interconnects and a high drive current of around 2 µA µm-1 at a supply voltage of 5 V. Notably, these achieved parameters are on par with state-of-the-art flexible transistors based on metal-oxide, carbon nanotube and polycrystalline silicon materials on plastic substrates12-14. Furthermore, we realize a large-scale integrated circuit with more than 1,000 transistors and a stage-switching frequency greater than 1 MHz, for the first time, to our knowledge, in intrinsically stretchable electronics. Moreover, we demonstrate a high-throughput braille recognition system that surpasses human skin sensing ability, enabled by an active-matrix tactile sensor array with a record-high density of 2,500 units per cm2, and a light-emitting diode display with a high refreshing speed of 60 Hz and excellent mechanical robustness. The above advancements in device performance have substantially enhanced the abilities of skin-like electronics.

High-brightness all-polymer stretchable LED with charge-trapping dilution.

Next-generation light-emitting displays on skin should be soft, stretchable and bright1-7. Previously reported stretchable light-emitting devices were mostly based on inorganic nanomaterials, such as light-emitting capacitors, quantum dots or perovskites6-11. They either require high operating voltage or have limited stretchability and brightness, resolution or robustness under strain. On the other hand, intrinsically stretchable polymer materials hold the promise of good strain tolerance12,13. However, realizing high brightness remains a grand challenge for intrinsically stretchable light-emitting diodes. Here we report a material design strategy and fabrication processes to achieve stretchable all-polymer-based light-emitting diodes with high brightness (about 7,450 candela per square metre), current efficiency (about 5.3 candela per ampere) and stretchability (about 100 per cent strain). We fabricate stretchable all-polymer light-emitting diodes coloured red, green and blue, achieving both on-skin wireless powering and real-time displaying of pulse signals. This work signifies a considerable advancement towards high-performance stretchable displays.

Dynamic spatial progression of isolated lithium during battery operations.

The increasing demand for next-generation energy storage systems necessitates the development of high-performance lithium batteries1-3. Unfortunately, current Li anodes exhibit rapid capacity decay and a short cycle life4-6, owing to the continuous generation of solid electrolyte interface7,8 and isolated Li (i-Li)9-11. The formation of i-Li during the nonuniform dissolution of Li dendrites12 leads to a substantial capacity loss in lithium batteries under most testing conditions13. Because i-Li loses electrical connection with the current collector, it has been considered electrochemically inactive or 'dead' in batteries14,15. Contradicting this commonly accepted presumption, here we show that i-Li is highly responsive to battery operations, owing to its dynamic polarization to the electric field in the electrolyte. Simultaneous Li deposition and dissolution occurs on two ends of the i-Li, leading to its spatial progression toward the cathode (anode) during charge (discharge). Revealed by our simulation results, the progression rate of i-Li is mainly affected by its length, orientation and the applied current density. Moreover, we successfully demonstrate the recovery of i-Li in Cu-Li cells with >100% Coulombic efficiency and realize LiNi0.5Mn0.3Co0.2O2 (NMC)-Li full cells with extended cycle life.

Data-driven electrolyte design for lithium metal anodes.

Improving Coulombic efficiency (CE) is key to the adoption of high energy density lithium metal batteries. Liquid electrolyte engineering has emerged as a promising strategy for improving the CE of lithium metal batteries, but its complexity renders the performance prediction and design of electrolytes challenging. Here, we develop machine learning (ML) models that assist and accelerate the design of high-performance electrolytes. Using the elemental composition of electrolytes as the features of our models, we apply linear regression, random forest, and bagging models to identify the critical features for predicting CE. Our models reveal that a reduction in the solvent oxygen content is critical for superior CE. We use the ML models to design electrolyte formulations with fluorine-free solvents that achieve a high CE of 99.70%. This work highlights the promise of data-driven approaches that can accelerate the design of high-performance electrolytes for lithium metal batteries.

Electrolytes with moderate lithium polysulfide solubility for high-performance long-calendar-life lithium-sulfur batteries.

Lithium-sulfur (Li-S) batteries with high energy density and low cost are promising for next-generation energy storage. However, their cycling stability is plagued by the high solubility of lithium polysulfide (LiPS) intermediates, causing fast capacity decay and severe self-discharge. Exploring electrolytes with low LiPS solubility has shown promising results toward addressing these challenges. However, here, we report that electrolytes with moderate LiPS solubility are more effective for simultaneously limiting the shuttling effect and achieving good Li-S reaction kinetics. We explored a range of solubility from 37 to 1,100 mM (based on S atom, [S]) and found that a moderate solubility from 50 to 200 mM [S] performed the best. Using a series of electrolyte solvents with various degrees of fluorination, we formulated the Single-Solvent, Single-Salt, Standard Salt concentration with Moderate LiPSs solubility Electrolytes (termed S6MILE) for Li-S batteries. Among the designed electrolytes, Li-S cells using fluorinated-1,2-diethoxyethane S6MILE (F4DEE-S6MILE) showed the highest capacity of 1,160 mAh g-1 at 0.05 C at room temperature. At 60 °C, fluorinated-1,4-dimethoxybutane S6MILE (F4DMB-S6MILE) gave the highest capacity of 1,526 mAh g-1 at 0.05 C and an average CE of 99.89% for 150 cycles at 0.2 C under lean electrolyte conditions. This is a fivefold increase in cycle life compared with other conventional ether-based electrolytes. Moreover, we observed a long calendar aging life, with a capacity increase/recovery of 4.3% after resting for 30 d using F4DMB-S6MILE. Furthermore, the correlation between LiPS solubility, degree of fluorination of the electrolyte solvent, and battery performance was systematically investigated.

Evolution and Interplay of Lithium Metal Interphase Components Revealed by Experimental and Theoretical Studies.

Lithium metal batteries (LMB) have high energy densities and are crucial for clean energy solutions. The characterization of the lithium metal interphase is fundamentally and practically important but technically challenging. Taking advantage of synchrotron X-ray, which has the unique capability of analyzing crystalline/amorphous phases quantitatively with statistical significance, we study the composition and dynamics of the LMB interphase for a newly developed important LMB electrolyte that is based on fluorinated ether. Pair distribution function analysis revealed the sequential roles of the anion and solvent in interphase formation during cycling. The relative ratio between Li2O and LiF first increases and then decreases during cycling, suggesting suppressed Li2O formation in both initial and long extended cycles. Theoretical studies revealed that in initial cycles, this is due to the energy barriers in many-electron transfer. In long extended cycles, the anion decomposition product Li2O encourages solvent decomposition by facilitating solvent adsorption on Li2O which is followed by concurrent depletion of both. This work highlights the important role of Li2O in transitioning from an anion-derived interphase to a solvent-derived one.

Bamboo Inspired Silicon Anodes with Ultrahigh Initial Coulombic Efficiency and High Capacity for the Li-Ion Batteries.

Silicon is regarded as the most promising candidate due to its ultrahigh theoretical energy density (4200 mAh g-1). However, the large volume expansion of silicon nanoparticles would result in the destruction of electrodes and a shortened cycle lifetime. Here, inspired by the natural structure of bamboo, the silicon anode with vascular bundle-like structure is proposed to improve the electrochemical performance for the first time. The dense channel wall in the silicon anode can accommodate the volume change of silicon nanoparticles and the transport of ions and electrons is also enhanced. The obtained silicon anodes display excellent mechanical properties (50% compression resilience and the average peel force of 4.34 N) and good wettability. What more, the silicon anodes exhibit high initial coulombic efficiency (94.5%), excellent cycle stability (2100 mAh g-1 after 300 cycles) which stands out among the silicon anodes. Specially, the silicon anode with impressive areal capacity of 36.36 mAh cm-2 and initial coulombic efficiency of 84% is also achieved. This work offers a novel and efficient strategy for the preparation of the flexible electrodes with outstanding performance.

Proximity Matters: Interfacial Solvation Dictates Solid Electrolyte Interphase Composition.

The composition of the solid electrolyte interphase (SEI) plays an important role in controlling Li-electrolyte reactions, but the underlying cause of SEI composition differences between electrolytes remains unclear. Many studies correlate SEI composition with the bulk solvation of Li ions in the electrolyte, but this correlation does not fully capture the interfacial phenomenon of SEI formation. Here, we provide a direct connection between SEI composition and Li-ion solvation by forming SEIs using polar substrates that modify interfacial solvation structures. We circumvent the deposition of Li metal by forming the SEI above Li+/Li redox potential. Using theory, we show that an increase in the probability density of anions near a polar substrate increases anion incorporation within the SEI, providing a direct correlation between interfacial solvation and SEI composition. Finally, we use this concept to form stable anion-rich SEIs, resulting in high performance lithium metal batteries.

Suspension electrolyte with modified Li+ solvation environment for lithium metal batteries.

Designing a stable solid-electrolyte interphase on a Li anode is imperative to developing reliable Li metal batteries. Herein, we report a suspension electrolyte design that modifies the Li+ solvation environment in liquid electrolytes and creates inorganic-rich solid-electrolyte interphases on Li. Li2O nanoparticles suspended in liquid electrolytes were investigated as a proof of concept. Through theoretical and empirical analyses of Li2O suspension electrolytes, the roles played by Li2O in the liquid electrolyte and solid-electrolyte interphases of the Li anode are elucidated. Also, the suspension electrolyte design is applied in conventional and state-of-the-art high-performance electrolytes to demonstrate its applicability. Based on electrochemical analyses, improved Coulombic efficiency (up to ~99.7%), reduced Li nucleation overpotential, stabilized Li interphases and prolonged cycle life of anode-free cells (~70 cycles at 80% of initial capacity) were achieved with the suspension electrolytes. We expect this design principle and our findings to be expanded into developing electrolytes and solid-electrolyte interphases for Li metal batteries.

Potentiometric Measurement to Probe Solvation Energy and Its Correlation to Lithium Battery Cyclability.

The electrolyte plays a critical role in lithium-ion batteries, as it impacts almost every facet of a battery's performance. However, our understanding of the electrolyte, especially solvation of Li+, lags behind its significance. In this work, we introduce a potentiometric technique to probe the relative solvation energy of Li+ in battery electrolytes. By measuring open circuit potential in a cell with symmetric electrodes and asymmetric electrolytes, we quantitatively characterize the effects of concentration, anions, and solvents on solvation energy across varied electrolytes. Using the technique, we establish a correlation between cell potential (Ecell) and cyclability of high-performance electrolytes for lithium metal anodes, where we find that solvents with more negative cell potentials and positive solvation energies-those weakly binding to Li+-lead to improved cycling stability. Cryogenic electron microscopy reveals that weaker solvation leads to an anion-derived solid-electrolyte interphase that stabilizes cycling. Using the potentiometric measurement for characterizing electrolytes, we establish a correlation that can guide the engineering of effective electrolytes for the lithium metal anode.

Steric Effect Tuned Ion Solvation Enabling Stable Cycling of High-Voltage Lithium Metal Battery.

1,2-Dimethoxyethane (DME) is a common electrolyte solvent for lithium metal batteries. Various DME-based electrolyte designs have improved long-term cyclability of high-voltage full cells. However, insufficient Coulombic efficiency at the Li anode and poor high-voltage stability remain a challenge for DME electrolytes. Here, we report a molecular design principle that utilizes a steric hindrance effect to tune the solvation structures of Li+ ions. We hypothesized that by substituting the methoxy groups on DME with larger-sized ethoxy groups, the resulting 1,2-diethoxyethane (DEE) should have a weaker solvation ability and consequently more anion-rich inner solvation shells, both of which enhance interfacial stability at the cathode and anode. Experimental and computational evidence indicates such steric-effect-based design leads to an appreciable improvement in electrochemical stability of lithium bis(fluorosulfonyl)imide (LiFSI)/DEE electrolytes. Under stringent full-cell conditions of 4.8 mAh cm-2 NMC811, 50 µm thin Li, and high cutoff voltage at 4.4 V, 4 M LiFSI/DEE enabled 182 cycles until 80% capacity retention while 4 M LiFSI/DME only achieved 94 cycles. This work points out a promising path toward the molecular design of non-fluorinated ether-based electrolyte solvents for practical high-voltage Li metal batteries.

A New Class of Ionically Conducting Fluorinated Ether Electrolytes with High Electrochemical Stability.

Increasing battery energy density is greatly desired for applications such as portable electronics and transportation. However, many next-generation batteries are limited by electrolyte selection because high ionic conductivity and poor electrochemical stability are typically observed in most electrolytes. For example, ether-based electrolytes have high ionic conductivity but are oxidatively unstable above 4 V, which prevents the use of high-voltage cathodes that promise higher energy densities. In contrast, hydrofluoroethers (HFEs) have high oxidative stability but do not dissolve lithium salt. In this work, we synthesize a new class of fluorinated ether electrolytes that combine the oxidative stability of HFEs with the ionic conductivity of ethers in a single compound. We show that conductivities of up to 2.7 × 10-4 S/cm (at 30 °C) can be obtained with oxidative stability up to 5.6 V. The compounds also show higher lithium transference numbers compared to typical ethers. Furthermore, we use nuclear magnetic resonance (NMR) and molecular dynamics (MD) to study their ionic transport behavior and ion solvation environment, respectively. Finally, we demonstrate that this new class of electrolytes can be used with a Ni-rich layered cathode (NMC 811) to obtain over 100 cycles at a C/5 rate. The design of new molecules with high ionic conductivity and high electrochemical stability is a novel approach for the rational design of next-generation batteries.

Multivalent Assembly of Flexible Polymer Chains into Supramolecular Nanofibers.

Polymeric materials in nature regularly employ ordered, hierarchical structures in order to perform unique and precise functions. Importantly, these structures are often formed and stabilized by the cooperative summation of many weak interactions as opposed to the independent association of a few strong bonds. Here, we show that synthetic, flexible polymer chains with periodically placed and directional dynamic bonds collectively assemble into supramolecular nanofibers when the overall molecular weight is below the polymer's critical entanglement molecular weight. This causes bulk films of long polymer chains to have faster dynamics than films of shorter polymer chains of identical chemical composition. The formation of nanofibers increases the bulk film modulus by over an order of magnitude and delays the onset of terminal flow by more than 100 °C, while still remaining solution processable. Systematic investigation of different polymer chain architectures and dynamic bonding moieties along with coarse-grained molecular dynamics simulations illuminate governing structure-function relationships that determine a polymer's capacity to form supramolecular nanofibers. This report of the cooperative assembly of multivalent polymer chains into hierarchical, supramolecular structures contributes to our fundamental understanding of designing biomimetic functional materials.

Organic Semiconducting Alloys with Tunable Energy Levels.

Continuous band structure tuning, e.g., doping with different atoms, is one of the most important features of inorganic semiconductors. However, this can hardly be realized in organic semicondutors. Here, we report the first example of fine-tuning organic semiconductor band structures by alloying structurally similar derivatives into one single phase. By incorporating halogen atoms on different positions of the backbone, BDOPV derivatives with complementary intramolecular or intermolecular charge distributions were obtained. To maximize the Coloumbic attractive interactions and minimize repulsive interactions, they form antiparallel cofacial stacking in monocomponent or in alloy single crystals, resulting in efficient π orbital overlap. Benefiting from self-assembly induced solid state "olefin metathesis" reaction, it was observed, for the first time, that three BDOPV derivatives cocrystallized in one single crystal. Molecules with different energy levels serve like the dopants in inorganic semiconductors. Consequently, as the total number of halogen atoms increased, highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels of the alloy single crystals decreased monotonously in the range from -5.94 to -6.96 eV and -4.19 to -4.48 eV, respectively.

Fine-Tuning of Crystal Packing and Charge Transport Properties of BDOPV Derivatives through Fluorine Substitution.

Molecular packing in organic single crystals greatly influences their charge transport properties but can hardly be predicted and designed because of the complex intermolecular interactions. In this work, we have realized systematic fine-tuning of the single-crystal molecular packing of five benzodifurandione-based oligo(p-phenylenevinylene) (BDOPV)-based small molecules through incorporation of electronegative fluorine atoms on the BDOPV backbone. While these molecules all exhibit similar column stacking configurations in their single crystals, the intermolecular displacements and distances can be substantially modified by tuning of the amounts and/or the positions of the substituent fluorine atoms. Density functional theory calculations showed that the subtle differences in charge distribution or electrostatic potential induced by different fluorine substitutions play an important role in regulating the molecular packing of the BDOPV compounds. Consequently, the electronic couplings for electron transfer can vary from 71 meV in a slipped stack to 201 meV in a nearly cofacial antiparallel stack, leading to an increase in the electron mobility of the BDOPV derivatives from 2.6 to 12.6 cm(2) V(-1) s(-1). The electron mobility of the five molecules did not show a good correlation with the LUMO levels, indicating that the distinct difference in charge transport properties is a result of the molecular packing. Our work not only provides a series of high-electron-mobility organic semiconductors but also demonstrates that fluorination is an effective approach for fine-tuning of single-crystal packing modes beyond simply lowering the molecular energy levels.

High-Temperature Ash Melting and Fluidity Behavior upon the Cocombustion of Sewage Sludge and Coal.

Wastewater treatment produces a large amount of sludge, where the minimizing of the disposed sludge is essential for environmental protection. The co-combustion of sludge with coal is a preferable method for sewage sludge disposal from the economic and environmental perspective. The co-combustion of sludge has been widely used in the industry with the advantages of large processing capacity. The melting characteristics of ash are an important criterion for the selection of the co-combustion methods and furnace types. In this study, two types of sludge and four types of coal with different ash melting points were selected, where the ash melting behavior upon co-combustion is investigated by experimental and thermodynamical approaches. Especially, the slag fluidity upon co-combustion is explored via a modified inclined plane method. It has been found that the presence of SiO2 and CaO in sludge substantially enhances its fusion temperature owing to the high content of CaO, while SiO2 acts as a solvent, facilitating the co-melting of other oxides and raising the sludge fusion temperature. Fe2O3 exhibits a specific mass fraction within the range of 10-20%. Furthermore, the presence of CaO and SiO2 prohibits the flow ability of the slag at high temperatures, and Fe2O3 promotes the flow ability for sludge at high temperatures. With increasing base/acid ratio, the sludge flow velocity increases remarkably and peaks at 1.6. The interaction between Fe-Ca and Si-AI significantly affects the fluidity significantly. The findings are expected to optimize the condition of co-combustion and desirable furnace design for the incineration of sludge.

Superior Low-Temperature All-Solid-State Battery Enabled by High-Ionic-Conductivity and Low-Energy-Barrier Interface.

All-solid-state batteries (ASSBs) working at room and mild temperature have demonstrated inspiring performances over recent years. However, the kinetic attributes of the interface applicable to the subzero temperatures are still unidentified, restricting the low-temperature interface design and operation. Herein, a host of cathode interfaces are constructed and investigated to unlock the critical interface features required for cryogenic temperatures. The unstable interface between LiNi0.90Co0.05Mn0.05O2 (Ni90) and Li6PS5Cl (LPSC) sulfide solid electrolyte (SE) results in unfavorable cathode-electrolyte interphase (CEI) and sluggish lithium-ion transport across the CEI. After inserting a Li2ZrO3 (LZO) coating layer, the activation energy of the Ni90@LZO/sulfide SE interface can be reduced from 60.19 kJ mol-1 to 41.39 kJ mol-1 owing to the suppressed interfacial reactions. Through replacing the LPSC SE and LZO coating layer by the Li3InCl6 (LIC) halide SE, both a highly stable interface and low activation energy (25.79 kJ mol-1) can be achieved, thus realizing an improved capacity retention (26.9%) at -30 °C for the Ni90/LIC/LPSC/Li-In ASSB. Moreover, theoretical evaluation clarifies that cathode/SE interfaces with high ionic conductivity and low energy barrier are favorable to the Li+ conduction through the interphase and the Li+ transfer across the cathode/interphase interface. These critical understandings may provide guidance for low-temperature interface design in ASSBs.

Slidable and Highly Ionic Conductive Polymer Binder for High-Performance Si Anodes in Lithium-Ion Batteries.

Silicon is expected to become the ideal anode material for the next generation of high energy density lithium battery because of its high theoretical capacity (4200 mAh g-1 ). However, for silicon electrodes, the initial coulombic efficiency (ICE) is low and the volume of the electrode changes by over 300% after lithiation. The capacity of the silicon electrode decreases rapidly during cycling, hindering the practical application. In this work, a slidable and highly ionic conductive flexible polymer binder with a specific single-ion structure (abbreviated as SSIP) is presented in which polyrotaxane acts as a dynamic crosslinker. The ionic conducting network is expected to reduce the overall resistance, improve ICE and stabilize the electrode interface. Furthermore, the introduction of slidable polyrotaxane increases the reversible dynamics of the binder and improves the long-term cycling stability and rate performance. The silicon anode based on SSIP provides a discharge capacity of ≈1650 mAh g-1 after 400 cycles at 0.5C with a high ICE of upto 92.0%. Additionally, the electrode still exhibits a high ICE of 87.5% with an ultra-high Si loading of 3.84 mg cm-2 and maintains a satisfying areal capacity of 5.9 mAh cm-2 after 50 cycles, exhibiting the potential application of SSIP in silicon-based anodes.

Revealing the Multifunctions of Li3N in the Suspension Electrolyte for Lithium Metal Batteries.

Inorganic-rich solid-electrolyte interphases (SEIs) on Li metal anodes improve the electrochemical performance of Li metal batteries (LMBs). Therefore, a fundamental understanding of the roles played by essential inorganic compounds in SEIs is critical to realizing and developing high-performance LMBs. Among the prevalent SEI inorganic compounds observed for Li metal anodes, Li3N is often found in the SEIs of high-performance LMBs. Herein, we elucidate new features of Li3N by utilizing a suspension electrolyte design that contributes to the improved electrochemical performance of the Li metal anode. Through empirical and computational studies, we show that Li3N guides Li electrodeposition along its surface, creates a weakly solvating environment by decreasing Li+-solvent coordination, induces organic-poor SEI on the Li metal anode, and facilitates Li+ transport in the electrolyte. Importantly, recognizing specific roles of SEI inorganics for Li metal anodes can serve as one of the rational guidelines to design and optimize SEIs through electrolyte engineering for LMBs.