A 3,3'-Difluoro-2,2'-Bithiophene Based Donor Polymer Realizing High Efficiency (>17%) Single Junction Binary Organic Solar Cells.

In this study, two novel donor-acceptor (D-A) copolymers are designed and synthesized, DTBT-2T and DTBT-2T2F with 2,2'-bithiophene or 3,3'-difluoro-2,2'-bithiophene as the donor unit and dithienobenzothiadiazole as the acceptor unit, and used them as donor materials in non-fullerene organic solar cells (OSCs). Due to enhanced planarity of polymer chains resulted by the intramolecular F···S noncovalent interactions, the incorporation of 3,3'-difluoro-2,2'-bithiophene unit instead of 2,2'-bithiophene into the polymers can enhance their molecular packing, crystallinity and hole mobility. The DTBT-2T:L8-BO based binary OSCs deliver a power conversion efficiency (PCE) of only 9.71% with a Voc of 0.78 V, a Jsc of 20.69 mA cm-2 , and an FF of 59.67%. Moreover, the introduction of fluoro atoms can lower the highest occupied molecular orbital levels. As a result, DTBT-2T2F:L8-BO based single-junction binary OSCs exhibited less recombination loss, more balanced charge mobility, and more favorable morphology, resulting in an impressive PCE of 17.03% with a higher Voc of 0.89 V, a Jsc of 25.40 mA cm-2, and an FF of 75.74%. These results indicate that 3,3'-difluoro-2,2'-bithiophene unit can be used as an effective building block to synthesize high performance polymer donor materials. This work greatly expands the selection range of donor units for constructing high-performance polymers.

Hexylation Stabilises Twisted Backbone Configurations in the Prototypical Low-Bandgap Copolymer PCDTBT.

Conjugated donor-acceptor copolymers hold great potential as materials for high-performance organic photovoltaics, organic transistors and organic thermoelectric devices. Their low optical bandgap is achieved by alternation of donor and acceptor moieties along the polymer chain, leading to a pronounced charge-transfer character of electronic excitations. However, the influence of appended side chains and of chemical defects of the backbone on their photophysical and conformational properties remains largely unexplored on the level of individual chains. Here, we employ room temperature single-molecule photoluminescence spectroscopy on four compounds based on the prototypical copolymer PCDTBT with systematically changed chemical structure. Our results show that an increasing density of statistically added hexyl chains to the TBT comonomer distorts the molecular conformation, likely through the increase of average dihedral angles along the backbone. We find that, although the conformation becomes more twisted with high hexyl density, the side chains appear to stabilize the backbone in this twisted conformation. In addition, we demonstrate that homocoupling defects along the backbone barely influence the PL spectra of single chains, and thus intra-chain electronic properties.

Unfolding the Correlation between Solution Aggregation and Solid-State Crystal Orientation in Donor-Acceptor Copolymers via Solvent Additive Processing.

Tailoring the crystal orientation of donor-acceptor (D-A) copolymers is vital for boosting the performance of optoelectronic devices. Despite recent advances in controlling the crystal orientation of D-A copolymers in films, the investigation into their aggregates in solution and the correlation between the solution aggregates and solid-state crystal orientation has been limited. Herein, an effective solvent additive strategy is reported for tuning solution aggregates and the consequent solid-state structures of poly{[N,N'-bis(2-octyldodecyl)-naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,5'-(2,2'-bithiophene)} (P(NDI2OD-T2)). Specifically, the addition of 1-decanethiol (10-thiol) to the P(NDI2OD-T2) chloroform solution promoted the aggregation of P(NDI2OD-T2) chains because of the improved planarization of the backbones, which changed their crystal orientation in the film from coexisting edge-on and face-on to dominant edge-on when produced by drop-casting. The mechanism of this crystal orientation transformation is elucidated based on the interaction between 10-thiol and the side chains of P(NDI2OD-T2). The optical properties of P(NDI2OD-T2) films with different crystalline structures are closely correlated. Notably, the 10-thiol-enabled facile tailoring of the crystal orientation in P(NDI2OD-T2) can be readily applied to other D-A copolymers of interest. The findings of this study highlight a robust solvent additive strategy for regulating solution aggregates and crystal orientation in D-A copolymer films, which have applications in many optoelectronic devices.

Design, Synthesis, and Theoretical Studies on the Benzoxadiazole and Thienopyrrole Containing Conjugated Random Copolymers for Organic Solar Cell Applications.

In this study, six different donor-π-acceptor1-π-donor-acceptor2 type random co-polymers containing benzodithiophene as a donor, benzooxadiazole (BO), and thieno[3,4-c]pyrrole-4,6-dione (TPD) as acceptor, have been synthesized and characterized. In addition to the acceptor core ratio at different values, the effect of aromatic bridge structures on the optical, electronic, and photovoltaic properties of six different random co-polymers is investigated by using thiophene and selenophene structures as aromatic bridge units. To investigate how the acceptor unit ratio and replacement of aromatic bridge units impact the structural, electronic, and optical properties of the polymers, density functional theory (DFT) calculations are carried out for the tetramer models. The open-circuit voltage (VOC), which is strongly correlated with the HOMO levels of the donor material, is enhanced with the increasing ratio of the TPD moiety. On the other hand, the short-circuit current (JSC), which is associated with the absorption ability of the donor material, is improved by the increasing ratio of BO moiety with the π-bridges. BO moiety dominant selenophene π-bridged co-polymer (P4) showed the best performance with a power conversion efficiency (PCE) of 6.26%, a JSC of 11.44 mA cm2, a VOC of 0.80 V, and a fill factor (FF) of 68.81%.

Precision Synthesis of Various Low-Bandgap Donor-Acceptor Alternating Conjugated Polymers via Living Suzuki-Miyaura Catalyst-Transfer Polymerization.

Herein, we demonstrate that living Suzuki-Miyaura catalyst-transfer polymerization (SCTP) using a RuPhos Pd G3 precatalyst is a versatile method for the precision synthesis of various donor-acceptor alternating conjugated polymers (DA ACPs). First, the living SCTP of biaryl monomers with combinations of both medium to strong A and D were optimized to produce DA ACPs with controlled number average molecular weight (Mn ), narrow dispersity (Ð, 1.05-1.29), and high yield (>87 %). Moreover, its expansion to controlled polymerization (Mn =9.2-40.0 kg mol-1 ) of an A1 -D-A2 -D quateraryl monomer containing diketopyrrolopyrrole (DPP; strong A) was successful. The living SCTP also enabled the efficient one-pot synthesis of various diblock and triblock copolymers. Lastly, the DA ACPs showed tunable optical band gap (Eg opt , from 1.29 to 1.77 eV) and highest occupied molecular orbital (HOMO) level (from -5.57 to -4.75 eV), while their block copolymers exhibited broad absorption ranges and promising visible light-harvesting properties.

π-Extended Thiazole-Containing Polymer Semiconductor for Balanced Charge-Carrier Mobilities.

A low-band gap semiconducting polymer with an acceptor-donor-acceptor architecture is newly designed and synthesized by incorporating a π-extended thiazole-vinylene-thiazole unit. The resulting thiazole-containing diketopyrrolopyrrole copolymer exhibits well-balanced ambipolar characteristics with hole mobility of up to 0.11 cm2 V-1 s-1 and electron mobility of up to 0.30 cm2 V-1 s-1 , which are suitable for applications in polymer electronics.

Donor-Acceptor Copolymers with 9-(2-Ethylhexyl)carbazole or Dibenzothiophene-5,5-dioxide Donor Units and 5,6-Difluorobenzo[c][1,2,5]thiadiazole Acceptor Units for Photonics.

Semiconducting polymers, particularly of the third generation, including donor-acceptor (D-A) copolymers, are extensively studied due to their huge potential for photonic and electronic applications. Here, we report on two new D-A copolymers, CP1 and CP2, composed of different electron-donor (D) units: 9-(2-ethylhexyl)carbazole or dibenzothiophene-5,5-dioxide, respectively, and of 4,7-bis(4'-(2-octyldodecyl)thiophen-2'-yl)-5,6-difluorobenzo[c][1,2,5]thiadiazole building block with central 5,6-difluorobenzo[c][1,2,5]thiadiazole electron-acceptor (A) units, which were synthesized by Suzuki coupling in the high-boiling solvent xylene and characterized. The copolymers exhibited very good thermal and oxidation stability. A copolymer CP1 with different molecular weights was prepared in order to facilitate a comparison of CP1 with CP2 of comparable molecular weight and to reveal the relationship between molecular weight and properties. The photophysical, electrochemical, and electroluminescence properties were examined. Intense red photoluminescence (PL) with higher PL efficiencies for CP1 than for CP2 was observed in both solutions and films. Red shifts in the PL thin film spectra compared with the PL solution spectra indicated aggregate formation in the solid state. X-ray diffraction measurements revealed differences in the arrangement of molecules in thin films depending on the molecular weight of the copolymers. Light-emitting devices with efficient red emission and low onset voltages were prepared and characterized.

Effects of the Donor Unit on the Formation of Hybrid Layers of Donor-Acceptor Copolymers with Silver Nanoparticles.

Donor-acceptor (D-A) copolymers containing perylene-3,4,9,10-tetracarboxydiimide (PDI) electron-acceptor (A) units belonging to n-type semiconductors are of interest due to their many potential applications in photonics, particularly for electron-transporting layers in all-polymeric or perovskite solar cells. Combining D-A copolymers and silver nanoparticles (Ag-NPs) can further improve material properties and device performances. Hybrid layers of D-A copolymers containing PDI units and different electron-donor (D) units (9-(2-ethylhexyl)carbazole or 9,9-dioctylfluorene) with Ag-NPs were prepared electrochemically during the reduction of pristine copolymer layers. The formation of hybrid layers with Ag-NP coverage was monitored by in-situ measurement of absorption spectra. The Ag-NP coverage of up to 41% was higher in hybrid layers made of copolymer with 9-(2-ethylhexyl)carbazole D units than in those made of copolymer with 9,9-dioctylfluorene D units. The pristine and hybrid copolymer layers were characterized by scanning electron microscopy and X-ray photoelectron spectroscopy, which proved the formation of hybrid layers with stable Ag-NPs in the metallic state with average diameters <70 nm. The influence of D units on Ag-NP diameters and coverage was revealed.

Lateral Fully Organic P-N Diodes Created in a Single Donor-Acceptor Copolymer.

P-N junctions exist in many solid-state organic devices, such as light-emitting diodes, solar cells, and thermoelectric devices. Creating P-N junctions by bulk chemical doping in a single organic material (like silicon doped by boron and phosphorus) may capitalize the vast scientific and technological groundwork established in the inorganic semiconducting field. However, high-performance single-organic-material P-N junctions are seldom reported, because the diffusion of the dopant counterions often leads to transient rectification properties. Herein, a new type of lateral fully organic diodes created in single donor-acceptor (D-A) copolymer films with only one P-type dopant is reported. The achieved lateral devices exhibit high current densities of ≈3.83 A cm-2 and a high rectification ratio of ≈2100, which are beyond the requirements for high-frequency identification tags. The P- to N-type polarity switching mechanism is proposed after spectroscopic and structural tests. Decent stability of the organic diode is obtained, which is due to the long channel length and low diffusion speed of the large size of dopants. This work opens the opportunities to create P-N junctions in ways of silicon-based inorganic semiconductors and promises new opportunities for integrating organic materials for flexible and printable organic devices.

Driving Force and Optical Signatures of Bipolaron Formation in Chemically Doped Conjugated Polymers.

Molecular dopants are often added to semiconducting polymers to improve electrical conductivity. However, the use of such dopants does not always produce mobile charge carriers. In this work, ultrafast spectroscopy is used to explore the nature of the carriers created following doping of conjugated push-pull polymers with both F4 TCNQ (2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane) and FeCl3 . It is shown that for one particular push-pull material, the charge carriers created by doping are entirely non-conductive bipolarons and not single polarons, and that transient absorption spectroscopy following excitation in the infrared can readily distinguish the two types of charge carriers. Based on density functional theory calculations and experiments on multiple push-pull conjugated polymers, it is argued that the size of the donor push units determines the relative stabilities of polarons and bipolarons, with larger donor units stabilizing the bipolarons by providing more area for two charges to co-reside.

Hybrid Layers of Donor-Acceptor Copolymers with Homogenous Silver Nanoparticle Coverage for Photonic Applications.

Hybrid layers of donor-acceptor (D-A) copolymers containing N,N'-dialkylperylene-3,4,9,10-tetracarboxydiimide electron-acceptor units covered with silver nanoparticles (Ag-NPs) were prepared by electrochemical doping of pristine layers during reduction processes. In situ optical absorption spectra of the layers were recorded during the formation of Ag-NP coverage. The hybrid layers were characterized by absorption spectroscopy, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and energy dispersive X-ray spectroscopy (EDX). In the absorption spectra of the hybrid layers, a surface plasmon band characteristic of Ag-NPs appeared. Significant improvements in light absorption due to the plasmonic effects of Ag NPs were observed. Stable Ag-NPs with an average diameter of 41-63 nm were formed on the surface, as proven by SEM and XPS. The Ag-NP coverage and size depended on the hybrid layer preparation conditions and on the copolymer composition. The metallic character of the Ag-NPs was proven by XPS. The location in the surface layer was further confirmed by EDX analysis. To the best of our knowledge, this is the first report on such hybrid layers having the potential for a variety of photonic and electronic applications.

Energetic Control of Redox-Active Polymers toward Safe Organic Bioelectronic Materials.

Avoiding faradaic side reactions during the operation of electrochemical devices is important to enhance the device stability, to achieve low power consumption, and to prevent the formation of reactive side-products. This is particularly important for bioelectronic devices, which are designed to operate in biological systems. While redox-active materials based on conducting and semiconducting polymers represent an exciting class of materials for bioelectronic devices, they are susceptible to electrochemical side-reactions with molecular oxygen during device operation. Here, electrochemical side reactions with molecular oxygen are shown to occur during organic electrochemical transistor (OECT) operation using high-performance, state-of-the-art OECT materials. Depending on the choice of the active material, such reactions yield hydrogen peroxide (H2 O2 ), a reactive side-product, which may be harmful to the local biological environment and may also accelerate device degradation. A design strategy is reported for the development of redox-active organic semiconductors based on donor-acceptor copolymers that prevents the formation of H2 O2 during device operation. This study elucidates the previously overlooked side-reactions between redox-active conjugated polymers and molecular oxygen in electrochemical devices for bioelectronics, which is critical for the operation of electrolyte-gated devices in application-relevant environments.

N-Type Organic Thermoelectrics of Donor-Acceptor Copolymers: Improved Power Factor by Molecular Tailoring of the Density of States.

It is demonstrated that the n-type thermoelectric performance of donor-acceptor (D-A) copolymers can be enhanced by a factor of >1000 by tailoring the density of states (DOS). The DOS distribution is tailored by embedding sp2 -nitrogen atoms into the donor moiety of the D-A backbone. Consequently, an electrical conductivity of 1.8 S cm-1 and a power factor of 4.5 µW m-1 K-2 are achieved. Interestingly, an unusual sign switching (from negative to positive) of the Seebeck coefficient of the unmodified D-A copolymer at moderately high dopant loading is observed. A direct measurement of the DOS shows that the DOS distributions become less broad upon modifying the backbone in both pristine and doped states. Additionally, doping-induced charge transfer complexes (CTC) states, which are energetically located below the neutral band, are observed in DOS of the doped unmodified D-A copolymer. It is proposed that charge transport through these CTC states is responsible for the positive Seebeck coefficients in this n-doped system. This is supported by numerical simulation and temperature dependence of Seebeck coefficient. The work provides a unique insight into the fundamental understanding of molecular doping and sheds light on designing efficient n-type OTE materials from a perspective of tailoring the DOS.

Thermally induced anchoring of fullerene in copolymers with Si-bridging atom: Spectroscopic evidences.

We use X-ray photoelectron spectroscopy (XPS), Near-edge X-ray absorption fine structure (NEXAFS), resonant Auger spectroscopy (RAS), Attenuation Total Reflection Infrared (ATR-IR) and Atomic Force Microscopy (AFM) to study the blend between the copolymer poly[2,7-(9,9-bis(2-ethylhexyl)-dibenzosilole)-alt-4,7-bis(thiophen-2-yl)benzo-2,1,3-thiadiazole] (PSiF-DBT) and the fullerene derivative PC71BM submitted to different annealing temperatures. Those measurements indicate that there is an incidental anchoring of a fullerene derivative to the Si-bridging atoms of a copolymer induced by thermal annealing of the film. Insights about the physical properties of one possible PSiF-DBT/PC71BM anchored structure are obtained using Density Functional Theory calculations. Since the performance of organic photovoltaic based on polymer-fullerene blends depends on the chemical structure of the blend components, the anchoring effect might affect the photovoltaic properties of those devices.

Asymmetric-Indenothiophene-Based Copolymers for Bulk Heterojunction Solar Cells with 9.14% Efficiency.

The first two asymmetric-indenothiophene-based donor-acceptor copolymers (PITBT and PITFBT) are prepared through Stille coupling reactions between distannyl indenothiophene and brominated benzothiadiazole derivatives. The best performing solar cell fabricated from PITFBT exhibits a power conversion efficiency of 9.14% which demonstrates a great potential of the asymmetric indenothiophene for high-performance copolymers.

Computational engineering of low bandgap copolymers.

We present a conceptual approach to low bandgap copolymers, in which we clarify the physical parameters which control the optical bandgap, develop a fundamental understanding of bandgap tuning, unify the terminology, and outline the minimum requirements for accurate prediction of polymer bandgaps from those of finite length oligomers via extrapolation. We then test the predictive power of several popular hybrid and long-range corrected (LC) DFT functionals when applied to this task by careful comparison to experimental studies of homo- and co-oligomer series. These tests identify offset-corrected M06HF, with 100% HF exchange, as a useful alternative to the poor performance of tested hybrid and LC functionals with lower fractions of HF exchange (B3LYP, CAM-B3LYP, optimally-tuned LC-BLYP, BHLYP), which all significantly overestimate changes in bandgap as a function of system size.