Highly Anisotropic Thermally Conductive Dielectric Polymer/Boron Nitride Nanotube Composites for Directional Heat Dissipation.

An ideal dielectric material for microelectronic devices requires a combination of high anisotropic thermal conductivity and low dielectric constant (ɛ') and loss (tan δ). Polymer composites of boron nitride nanotubes (BNNTs), which offer excellent thermal and dielectric properties, show promise for developing these dielectric polymer composites. Herein, a simple method for fabricating polymer/BNNT composites with high directional thermal conductivity and excellent dielectric properties is presented. The nanocomposites with directionally aligned BNNTs are fabricated through melt-compounding and in situ fibrillation, followed by sintering the fibrous nanocomposites. The fabricated nanocomposites show a significant enhancement in thermal properties, with an in-plane thermal conductivity (K‖) of 1.8 Wm-1K-1-a 450% increase-yielding a high anisotropy ratio (K‖/K⊥) of 36, a 1700% improvement over isotropic samples containing only 7.2 vol% BNNT. These samples exhibit a 120% faster in-plane heat dissipation compared to the through-plane within 2 s. Additionally, they display low ɛ' of ≈3.2 and extremely low tan δ of ≈0.014 at 1 kHz. These results indicate that this method provides a new avenue for designing and creating polymer composites with enhanced directional heat dissipation properties along with high K‖, suitable for thermal management applications in electronic packaging, thermal interface materials, and passive cooling systems.

Bioinspired Hollow/Hollow Architecture with Flourishing Dielectric Properties for Efficient Electromagnetic Energy Reclamation Device.

The exploitation of advanced electromagnetic functional devices is perceived as the effective prescription to deal with environmental contamination and energy deficiency. From the perspective of observing and imitating nature, pine branch-like zirconium dioxide/cobalt nanotubes@nitrogen-doped carbon nanotubes are synthesized victoriously through maneuverable electrospinning process and follow-up thermal treatments. In particular, introducing carbon nanotubes on the surface of hollow nanofibers to construct hierarchical architecture vastly promoted the material's dielectric properties by significantly augmenting specific surface area, generating abundant heterogeneous interfaces, and inducing the formation of defects. Supplemented by the synergistic effect between each constituent, ultra-strong attenuation capacity and perfect impedance matching characteristics are implemented simultaneously, and jointly made contributions to the splendid microwave absorption performance with a minimum reflection loss of -67.9 dB at 1.5 mm. Moreover, this fibrous absorber also exhibited promising potential to be utilized as a green and efficient electromagnetic interference shielding material when the filler loading is enhanced. Therefore, this design philosophy is destined to inspire the future development of energy conversion and storage devices, and provide theoretical direction for the creation of sophisticated electromagnetic functional materials.

Trifluoromethyl Fluorosulfonate (CF3OSO2F) and Trifluoromethoxy Sulfur Pentafluoride (CF3OSF5) - Two Gaseous Sulfur(VI) Compounds with Insulating Properties.

In this work, we analyzed trifluoromethyl fluorosulfonate (CF3OSO2F) and trifluoromethoxy sulfur pentafluoride (CF3OSF5) regarding their potential use as dielectrics by investigating some of their intrinsic and extrinsic properties. Both compounds show a higher breakdown voltage than SF6 with averaged relative breakdown voltages of 1.3±0.2 for CF3OSO2F and 1.4±0.2 for CF3OSF5 compared to SF6 with 1.0. Like the dielectric (CF3)2CFCN, both compounds decompose during the breakdown process. The decomposition products were analyzed by IR spectroscopy and GCIR methods. Furthermore, the molecular structures of both gaseous compounds CF3OSO2F and CF3OSF5 have been determined by in situ crystallization, and their physical properties were determined as well.

Synthesis of flowerlike vanadium diselenide microspheres for efficient electromagnetic wave absorption.

The revelation of MoS2as an efficient electromagnetic wave (EMW) absorbing material has ratcheted up people's attention to other transition metal dichalcogenides (TMDs). To date, extensive studies have been conducted on the semiconducting VIB-Group TMDs while research into metallic VB-Group TMDs has been relatively rare. In this work, we successfully fabricated VB-Group VSe2microspheres through a facile one-step hydrothermal method and used them as EMW absorbers. The flowerlike VSe2microspheres based on VSe2nanosheets exhibited a minimum reflection loss of 46.58 dB with an effective absorption bandwidth of 4.86 GHz. The influence of material morphology, microstructure, and dielectric properties on the EMW absorption performance was systematically investigated. The hierarchically layered structure promoted dielectric loss and EMW absorption by means of multiple reflection, interfacial polarization and related relaxation, and enhanced attenuation ability. This work not only demonstrates that VSe2is potentially a high-efficiency single component EMW absorber, but also provides fresh insights into exploration on the EMW loss mechanisms of the metallic TMD-based absorbing materials.

Innovative synthesis technique for high-performance dielectric resonator antennas: laser-induced shockwave sintering of potassium sodium niobate (KNN).

This study explored the synthesis and sintering of potassium sodium niobate (KNN) nanoparticles, emphasizing morphology, crystal structure, and sintering methods. The as-synthesized KNN nanoparticles exhibited a spherical morphology below 200 nm. Solid state sintering (SSS) and laser-induced shockwave sintering (LISWS) were compared, with LISWS producing denser microstructures and improved grain growth. Raman spectroscopy and x-ray diffraction confirmed KNN perovskite structure, with LISWS demonstrating higher purity. High-resolution x-ray photoelectron spectroscopy spectra indicated increased binding energies in LISWS, reflecting enhanced density and crystallinity. Dielectric and loss tangent analyses showed temperature-dependent behavior, with LISWS-3 exhibiting superior properties. Antenna performance assessments revealed LISWS-3's improved directivity and reduced sidelobe radiation compared to SSS, attributed to its denser microstructure. Overall, LISWS proved advantageous for enhancing KNN ceramics, particularly in antenna applications.

Core@Double-Shell Engineering of Zn Particles toward Elevated Dielectric Properties: Multiple Polarization Mechanisms in Zn@Znch@PS/PVDF Composites.

Flexible dielectrics with large dielectric constant (ε') coupled with low loss are highly pursued in many applications. To bolster the ε' of raw Zn (zinc)/poly(vinylidene fluoride, PVDF) while maintaining pimping dielectric loss, in this study, the core@double-shell structured Zn@zinc carbonate (ZnCH)@polystyrene (PS) particles are first synthesized through a suspension polymerization of styrene, and then composited with PVDF to elevate the ε' and keep low loss of the composites. By optimizing the PS shells' thickness and tailoring the electrical resistivity of Zn@ZnCH@PS particles, both the slow inter-particle polarization and fast intra-particle polarization in the composites can be decoupled and synergistically tuned, thus, the Zn@ZnCH@PS/PVDF achieves a much higher ε' and lower dielectric loss, simultaneously, which far exceed the unmodified Zn/PVDF. Both experiment and theoretic calculation reveal that the double-shell ZnCH@PS not only induces and promotes multiple polarizations enhancing the composites' ε', especially at the optimized PS's thickness, but also maintains suppressed loss and conductivity thanks to their obvious barrier effect on long-range charge migration. The core@double-shell filler design strategy facilitates the development of polymer composites with desirable dielectric properties for applications in electronic and electrical power systems.

Manipulating Cis-Trans Copolymer Chain Conformation to Simultaneously Improve Permittivity and DC Breakdown Strength in Polythiourea.

Polythioureas (PTUs) show great potentials for applications in the new generation of film capacitors due to their excellent dielectric properties. Herein, the cis-trans copolymer chain of PTU is successfully tailored by employing cis and trans cyclohexyl spacers. The relationship between the copolymer chain conformation, microstructure, and dielectric properties is carefully explored by a series of analysis. Compared with cis conformation, the trans with less steric hindrance can promote the formation of H-bonds. The enhanced H-bonding interactions not only reduce the molecular inter-chain spacing, but also drive the self-assembly of molecular chains to form cylindrical and droplet nano-morphologies. The phase separation between cis and trans PTUs is confirmed by combining the experimental results of TEM and DSC, and the CT64-PTU with the most two-phase interface thus obtains the highest permittivity of 5.5 (@10 Hz). The reduced molecular inter-chain spacing is accompanied by a decreased hopping distance of charges, which improves breakdown strength by 17% from 498 MV/m to 580 MV/m. Therefore, the cis-trans copolymer chain conformation in PTU provides a simultaneous high permittivity and breakdown strength. This research offers a strategy to further design high-performance dielectrics via regulation of copolymer chain conformation.

Constructing Novel High Dielectric Constant Polyimides Containing Dipolar Pendant Groups with Enhanced Orientational Polarization.

Polymer dielectrics with high dielectric constant are urgently demanded for potential electrical and pulsed power applications. The design of polymers with side chains containing dipolar groups is considered an effective method for preparing materials with a high dielectric constant and low loss. This study synthesizes and comprehensively compare the dielectric properties of novel polyimides with side chains containing urea (BU-PI), carbamate (BC-PI), and sulfonyl (BS-PI) functional groups. The novel polyimides exhibit relatively high dielectric constant and low dielectric loss values due to the enhanced orientational polarization and suppressed dipole-dipole interactions of dipolar groups. In particular, BU-PI containing urea pendant groups presents the highest dielectric constant of 6.14 and reasonably low dielectric loss value of 0.0097. The strong γ transitions with low activation energies derived from dielectric spectroscopy measurements have been further evaluated to demonstrate the enhanced free rotational motion of urea pendant dipoles. In energy storage applications, BU-PI achieves a discharged energy density of 6.92 J cm-3 and a charge-discharge efficiency above 83% at 500 MV m-1. This study demonstrates that urea group, as dipolar pendant group, can provide polymers with better dielectric properties than the most commonly used sulfonyl groups.

Reconstruction of the Permittivity of Ex Vivo Animal Tissues in the Frequency Range 1-20 GHz Using a Water-Based Dielectric Model.

Several medical techniques are based on the application of electromagnetic fields (EMFs) on the human body with therapeutic and/or diagnostic aims. The response of human tissues to the applied EMF is mediated by the tissues' dielectric properties, which must therefore be characterized at the frequencies of the considered technique. Due to the heterogeneity and complexity of biological tissues, it is necessary to know their properties in vivo for the specific condition of interest. Traditional techniques for the dielectric characterization of biological tissues are invasive and, as such, not adoptable for this aim. Accordingly, alternative sensors and/or sensing methods are needed. Recently, a new wideband spectroscopy technique was proposed, based on quantities derived from the Magnetic Resonance (MRI) signal. Among these quantities, the water content was proposed to evaluate the dielectric properties at frequencies around a few GHz. This work verifies the possibility of deriving tissues' dielectric properties in the frequency range of 1-20 GHz based on knowledge of the water content. The water content was retrieved through a dehydration procedure for five different ex vivo tissues. The achieved results were compared with references from the literature.

A Method for Sensing Dielectric Properties of Thin and Flexible Conductive Biocomposites.

This study investigates the dielectric properties of conductive biocomposites (CBs), which are integral to the development of advanced materials for flexible electronics and medical devices. A novel method employing Microwave Reflectometry (MR) is introduced, utilizing a miniaturized Vector Network Analyzer (m-VNA) and a dedicated sensing element (SE), to extract the dielectric properties of CBs. The method is grounded in a minimization principle, aligning the measured S11 reflection scattering parameter with its electromagnetic (EM) simulation, facilitating a refined process for determining the dielectric properties. The experimental setup was meticulously engineered, optimized, and validated using reference dielectric samples (RDSs) with known dielectric properties. The method was then applied to three innovative CBs, resulting in an accurate extrapolation of their dielectric properties. The findings highlight the method's versatility, cost-efficiency, and applicability to ultra-thin and flexible biopolymer films, offering significant potential for advancements in flexible electronics and bio-sensing applications.

Dielectric Properties of Materials Used for Microwave-Based NOx Gas Dosimeters.

Nitrogen oxides (NOx), primarily generated from combustion processes, pose significant health and environmental risks. To improve the coordination of measures against excessive NOx emissions, it is necessary to effectively monitor ambient NOx concentrations, which requires the development of precise and cost-efficient detection methods. This study focuses on developing a microwave- or radio frequency (RF)-based gas dosimeter for NOx detection and addresses the optimization of the dosimeter design by examining the dielectric properties of LTCC-based (Low-Temperature Co-fired Ceramics) sensor substrates and barium-based NOx storage materials. The measurements taken utilizing the Microwave Cavity Perturbation (MCP) method revealed that these materials exhibit more pronounced changes in dielectric losses when storing NOx at elevated temperatures. Consequently, operating such a dosimeter at high temperatures (above 300 °C) is recommended to maximize the sensor signal. To evaluate their high-temperature applicability, LTCC substrates were analyzed by measuring their dielectric losses at temperatures up to 600 °C. In terms of NOx storage materials, coating barium on high-surface-area alumina resolved issues related to limited NOx adsorption in pure barium carbonate powders. Additionally, the adsorption of both NO and NO2 was enabled by the application of a platinum catalyst. The change in dielectric losses, which provides the main signal for an RF-based gas dosimeter, only depends on the stored amount of NOx and not on the specific type of nitrogen oxide. Although the change in dielectric losses increases with the temperature, the maximum storage capacity of the material decreases significantly. In addition, at temperatures above 350 °C, NOx is mostly weakly bound, so it will desorb in the absence of NOx. Therefore, in the future development of a reliable RF-based NOx dosimeter, the trade-off between the sensor signal strength and adsorption behavior must be addressed.

One-Port Coaxial Line Sample Holder Characterisation Method of Dielectric Spectra.

A technique for solving the one-port closed coaxial transmission line sample holder scattering equation for complex permittivity inversion for lossy materials is presented. A non-linear least-squares procedure is used for the determination of parameters for the specification of the spectral functional form of the complex permittivity. The method allows for accurate retrieval of many low- and high-permittivity dielectric materials in the frequency range of 1 GHz to 3 GHz inserted into the coaxial cell. Using this method, the complex permittivity of a number of liquids and a Maltese soil known as Bajjad soil have been extracted by measurements using a short terminated coaxial transmission line sample holder. The proposed novel inversion method is mainly based on the reflection coefficient of the test material. The measured results of the complex permittivity of liquid dielectrics such as ethanol, methanol, and TX100 are validated and compared with previously published data obtained from measurements made by the National Physical Laboratory (NPL) using a two-port measurement setup made with the same commercial coaxial transmission line sample holder used in the one-port setup. Since the technique allows broadband measurements, it has been used to characterise the soil dielectric spectrum in the frequency range of 1-3 GHz, which is also compared with results from a two-port setup of the same coaxial line. The experimental results are a validation of the proposed approach for different types of materials.

Open-Ended Coaxial Probe for Effective Reconstruction of Biopsy-Excised Tissues' Dielectric Properties.

Dielectric characterization is extremely promising in medical contexts because it offers insights into the electromagnetic properties of biological tissues for the diagnosis of tumor diseases. This study introduces a promising approach to improve accuracy in the dielectric characterization of millimeter-sized biopsies based on the use of a customized electromagnetic characterization system by adopting a coated open-ended coaxial probe. Our approach aims to accelerate biopsy analysis without sample manipulation. Through comprehensive numerical simulations and experiments, we evaluated the effectiveness of a metal-coating system in comparison to a dielectric coating with the aim for replicating a real scenario: the use of a needle biopsy core with the tissue inside. The numerical analyses highlighted a substantial improvement in the reconstruction of the dielectric properties, particularly in managing the electric field distribution and mitigating fringing field effects. Experimental validation using bovine liver samples revealed highly accurate measurements, particularly in the real part of the permittivity, showing errors lower than 1% compared to the existing literature data. These results represent a significant advancement for the dielectric characterization of biopsy specimens in a rapid, precise, and non-invasive manner. This study underscores the robustness and reliability of our innovative approach, demonstrating the convergence of numerical analyses and empirical validation.

Synthesis, the Reversible Isostructural Phase Transition, and the Dielectric Properties of a Functional Material Based on an Aminobenzimidazole-Iron Thiocyanate Complex.

By introducing disordered molecules into a crystal structure, the motion of the disordered molecules easily induces the formation of multidimensional frameworks in functional crystal materials, allowing for structural phase transitions and the realization of various dielectric properties within a certain temperature range. Here, we prepared a novel ionic complex [C7H8N3]3[Fe(NCS)6]·H2O (1) between 2-aminobenzimidazole and ferric isothiocyanate from ferric chloride hexahydrate, ammonium thiocyanate, and 2-aminobenzimidazole using the evaporation of the solvent method. The main components, the single-crystal structure, and the thermal and dielectric properties of the complex were characterized using infrared spectroscopy, elemental analysis, single-crystal X-ray diffraction, powder XRD, thermogravimetric analysis, differential scanning calorimetry, variable-temperature and variable-frequency dielectric constant tests, etc. The analysis results indicated that compound 1 belongs to the P21/n space group. Within the crystal structure, the [Fe(NCS)6]3- anion formed a two-dimensional hydrogen-bonded network with the organic cation through S···S interactions and hydrogen bonding. The disorder-order motion of the anions and cations within the crystal and the deformation of the crystal frameworks lead to a significant reversible isostructural phase transition and multiaxial dielectric anomalies of compound 1 at approximately 240 K.

Extraction of rare earth Eu from waste blue phosphor strengthened by microwave alkali roasting.

Spent phosphor is an important secondary resource for extracting rare earth elements. Microwave absorption properties and enhanced extraction of Eu from blue phosphor by microwave alkali roasting were studied. Dielectric properties of alkali roasting system were measured by resonator perturbation method. Dielectric constant increases linearly from 250 °C until it reaches a peak at 400 °C. The dielectric loss reaches a higher value at 400-550 °C, due to the strong microwave absorption properties of molten alkali and roasted products. Effects of roasting temperature, roasting time and alkali addition amount on Eu leaching were investigated. The phosphor was completely decomposed into Eu2O3, BaCO3 and MgO at 400 °C. The alkaline decomposition process of phosphor is more consistent with diffusion control model with Eα being 28.9 kJ/mol. Effects of the main leaching conditions on Eu leaching were investigated. The leaching kinetic of Eu was in line with diffusion control model with Eα being 5.74 kJ/mol. The leaching rules of rare earths in the mixed phosphor were studied. The results showed that the presence of red and green phosphor affected the recovery of blue phosphor. The optimum process parameters of rare earth recovery in single blue phosphor and mixed phosphor were obtained, and the recovery of Eu were 97.81% and 94.80%, respectively. Microwave alkali roasting promoted the dissociation of phosphor and leaching of rare earths. The results can provide reference for the efficient and selective recovery of rare earths in phosphors.

Te4+ and Er3+ doped ZrO2 nanoparticles with enhanced photocatalytic, antibacterial activity and dielectric properties: A next generation of multifunctional material.

Amid rising water contamination from industrial sources, tackling toxic dyes and pathogens is critical. Photocatalysis offers a cost-effective and eco-friendly solution to this pressing challenges. Herein, we synthesized Te4+ and Er3+ doped ZrO2 photocatalysts through hydrothermal method and investigated their efficacy in degrading Congo red (CR) and pathogens under visible light. XRD and Raman Spectroscopy confirm monoclinic and tetragonal mixed-phases without any impurities. Doping-induced defects, reduced crystalline diameter, high surface area, modified bandgap (2.95 eV), photoluminescence quenching, coupled with interfacial polarization, contribute to EZO's excellent dielectric response (1.149 × 106), for achieving remarkable photocatalytic activity, verified by photoelectrochemical measurements, LC-MS and phytotoxicity analysis. Under optimal conditions, EZO achieves 99% CR degradation within 100 min (TOC 79.9%), surpassing ZO (77%) and TZO (84%). Catalyst dosages, dye concentrations, and solution pH effect on EZO's photocatalytic performance are systematically assessed. Scavenging experiment emphasized the pivotal role of · OH in CR degradation with 96.4% efficiency after 4 cycles, affirming its remarkable stability. Moreover, EZO demonstrates ROS-mediated antibacterial activity against E. faecalis and E. coli bacteria under visible light, achieving >97% and >94% inhibition rate with an inhibition zone > 3 mm. Hence, the nanoparticle's dual action offers a practical solution for treating contaminated wastewater, ensuring safe irrigation.

Catalytic Transformation of Nitroarenes to Amines over Ba(1-x)SrxTiO3 (0 < x < 1) Perovskites in Water.

This work is focused on the application of lanthanide-free perovskite Ba1-xSrxTiO3 (0 < x < 1) in valorization of toxic pollutants as 4-nitrophenol (4-NPh). The series of perovskites were fabricated by facile, one-step solid-state preparation method and characterized via various techniques: elemental analysis (Inductively Coupled Plasma Optical Emission Spectrometry, ICP-OES), powder X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR) and dielectric properties (impedance spectroscopy, IS). The methods confirmed the assumed composition, structure and high purity of the materials. The results showed that substitution of Ba2+ by Sr2+ in the perovskite crystal lattice influenced the dielectric properties of samples and the size of the grains. The absorption and catalytic properties of Ba(1-x)SrxTiO3 (0 < x < 1) series were evaluated in reduction of 4-NPh in water using NaBH4 as reducing agent. No adsorption of 4-NPh was found for all the materials during 180 min of contact (experiment without reducing agent), and the best catalytic performance was found for the Ba(1-x)SrxTiO3 (x = 0.3) sample. The catalytic transformation of 4-NPh to 4-APh follows a pseudo-first-order model, and the catalysts can be easily regenerated via mild annealing (300 °C).

Dielectric and Magnetoelectric Properties of TGS-Magnetite Composite.

In our studies, we combined two powdered materials, i.e., ferroelectric triglycine sulfate (TGS) and ferrimagnetic magnetite Fe3O4, to obtain a magnetoelectric composite. The ferroelectric (E) part, i.e., TGS, was a hybrid organic-inorganic crystal, which we obtained as a pure single crystal from an aqueous solution using a static water evaporation method. The magnetic (M) part of the composite was commercially available magnetite. The samples used for the dielectric and magnetoelectric measurements were cold-pressed and made in the form of a circular tablet. The measuring electrodes were made of silver-based conductive paste and were attached to the sample. We measured the temperature dependencies of selected electrical parameters (e.g., dielectric permittivity, electrical capacity, and loss angle tangent). We used the dynamic lock-in method to check whether magnetoelectric coupling existed between the E and M phases. In this paper, we present the dielectric properties of pure monocrystalline TGS as a reference sample and compare the results for TGS powder, TGS + carbon powder, and TGS + Fe3O4 powder. The magnetoelectric coupling presumably appeared for the composite TGS + 10 wt. % Fe3O4, as evidenced by the shift in the phase transition temperature in the TGS. Moreover, the theoretical interpretation of the effect is proposed.

Enhancing the Conductivity and Dielectric Characteristics of Bismuth Oxyiodide via Activated Carbon Doping.

Activated carbon/BiOI nanocomposites were successfully synthesized through a simplistic method. The produced composites were then characterized using XRD, TEM, SEM-EDX, and XPS. The results showed that BiOI with a tetragonal crystal structure had been formed. The interaction between activated carbon and BiOI was confirmed via all the mentioned tools. The obtained nanocomposites' electrical conductivity, dielectric properties, and Ac impedance were studied at 59 KHz-1.29 MHz. AC and dc conductivities were studied at temperatures between 303 and 573 K within the frequency range of 59 KHz-1.29 MHz. The 10% activated carbon/BiOI nanocomposite possessed dc and AC conductivity values of 5.56 × 10-4 and 2.86 × 10-4 Ω-1.cm-1, respectively, which were higher than BiOI and the other nanocomposites. Every sample exhibited increased electrical conductivity values as the temperature and frequency rose, suggesting that all samples had semiconducting behavior. The loss and dielectric constants (ε' and ε″) also dropped as the frequency increased, leading to higher dielectric loss. The Nyquist plot unraveled single semicircle arcs and a decreased bulk resistance, indicating decreased grain boundary resistance. Consequently, the electrical characteristics of BiOI, 1C/BiOI, 5C/BiOI, and 10C/BiOI implied their applicability as dielectric absorbers, charge-stored capacitors, and high-frequency microwave devices.

Application of radio frequency energy in processing of fruit and vegetable products.

Thermal processing is commonly employed to ensure the quality and extend the shelf-life of fruits and vegetables. Radio frequency (RF) heating has been used as a promising alternative treatment to replace conventional thermal processing methods with advantages of rapid, volumetric, and deep penetration heating characteristics. This article provides comprehensive information regarding RF heating uniformity and applications in processing of fruit and vegetable products, including disinfestation, blanching, drying, and pasteurization. The dielectric properties of fruits and vegetables and their products have also been summarized. In addition, recommendations for future research on RF heating are proposed to enhance practical applications for fruits and vegetables processing in future.