Correlation between the activation energy of PLA respectively PLA/starch composites and mechanical properties with regard to differ accelerated aging conditions.

Within this research semi-crystalline polylactide and composites with 50 wt.% native potato starch were compounded and injection molded. The material was mechanically characterized by tensile, three-point bending, and Charpy impact tests. These tests were carried out in the freshly molded state and after 332 and 792 h of storage at accelerated temperature or humidity. The respective activation energy was calculated by applying the Flynn-Wall-Ozawa method. The focus of the study was to investigate the correlation between the activation energy and the related mechanical and thermal properties. The results showed that the addition of native potato starch as a filler prevents the decrease in activation energy over the course of the experiments. Thus, the PLA/starch composite is more resistant to the two aging conditions than the pure PLA. When considering the mechanical properties, the pure PLA showed a large deviation of results compared to the initial value in a range of +63.88% to -33.96% with regard to the respective aging conditions, whereas the PLA/starch composite properties nearly always remained at the initial values. Through the investigation of the mechanical and thermal properties, it was shown that the steady activation energies are consistent with the mechanical properties, as these have shown only a small deviation of the mechanical properties during the duration of experiments for the PLA/starch composite.

3D printing in pediatric neurosurgery: experimental study of a novel approach using biodegradable materials.

PURPOSE: 3D printing technologies have become an integral part of modern life, and the most routinely used materials in reconstructive surgery in children are biodegradable materials. The combination of these two technologies opens up new possibilities for the application of innovative methods in neurosurgery and a patient-centered approach in medical care. The aim of the study was to determine whether a physician without specialized programming and printing skills could independently create materials in a clinical setting for the treatment of patients. METHODS: We conducted a preclinical study on 15 male Balb-C mice. Cylindrical materials made of polylactic acid (PLA) plastic were 3D printed. Sterilization of the obtained material was performed using a cold plasma sterilizer with hydrogen peroxide vapor and its plasma. The sterile material was implanted subcutaneously into the mice for 30 days, followed by histological examination. Using open-source software for modeling and printing, plates and screws made of PLA plastic were manufactured. The produced components were tested in the biomedical laboratory of the institute. RESULTS: The histological material showed that no inflammatory changes were observed at the implantation site during the entire observation period. The cellular composition is mainly represented by macrophages and fibroblasts. There was a gradual resolution of the material and its replacement by native tissues. Research conducted to assess the effectiveness of material sterilization in a cold plasma sterilizer demonstrated its high bactericidal efficiency. CONCLUSION: The method we developed for obtaining biodegradable plates and fixation elements on a 3D printer is easy to use and has demonstrated safety in a preclinical study on an animal model.

Structure and Properties of Polylactide Composites with TiO2-Lignin Hybrid Fillers.

The research presented in this article focuses on the use of inorganic-organic material, based on titanium dioxide and lignin, as a filler for polylactide (PLA) biocomposites. To date, no research has been conducted to understand the impact of hybrid fillers consisting of TiO2 and lignin on the supermolecular structure and crystallization abilities of polylactide. Polymer composites containing 1, 3 or 5 wt.% of hybrid filler or TiO2 were assessed in terms of their structure, morphology, and thermal properties. Mechanical properties, including tensile testing, bending, impact strength, and hardness, were discussed. The hybrid filler is characterized by a very good electrokinetic stability at pH greater than 3-4. The addition of all fillers led to a small decrease in the glass transition temperature but, most importantly, the addition of 1% of the hybrid filler to the PLA matrix increased the degree of crystallinity of the material by up to 20%. Microscopic studies revealed differences in the crystallization behavior and nucleation ability of fillers. The use of hybrid filler resulted in higher nucleation density and shorter induction time than in unfilled PLA or PLA with only TiO2. The introduction of small amounts of hybrid filler also affected the mechanical properties of the composites, causing an increase in bending strength and hardness. This information may be useful from a technological process standpoint and may also help to increase the range of applicability of biobased materials.

Degradation of Polylactic Acid/Polypropylene Carbonate Films in Soil and Phosphate Buffer and Their Potential Usefulness in Agriculture and Agrochemistry.

Blends of poly(lactic acid) (PLA) with poly(propylene carbonate) (PPC) are currently in the phase of intensive study due to their promising properties and environmentally friendly features. Intensive study and further commercialization of PPC-based polymers or their blends, as usual, will soon face the problem of their waste occurring in the environment, including soil. For this reason, it is worth comprehensively studying the degradation rate of these polymers over a long period of time in soil and, for comparison, in phosphate buffer to understand the difference in this process and evaluate the potential application of such materials toward agrochemical and agricultural purposes. The degradation rate of the samples was generally accompanied by weight loss and a decrease in molecular weight, which was facilitated by the presence of PPC. The incubation of the samples in the aqueous media yielded greater surface erosions compared to the degradation in soil, which was attributed to the leaching of the low molecular degradation species out of the foils. The phytotoxicity study confirmed the no toxic impact of the PPC on tested plants, indicating it as a "green" material, which is crucial information for further, more comprehensive study of this polymer toward any type of sustainable application.

Nanostructured Coatings Based on Graphene Oxide for the Management of Periprosthetic Infections.

To modulate the bioactivity and boost the therapeutic outcome of implantable metallic devices, biodegradable coatings based on polylactide (PLA) and graphene oxide nanosheets (nGOs) loaded with Zinforo™ (Zin) have been proposed in this study as innovative alternatives for the local management of biofilm-associated periprosthetic infections. Using a modified Hummers protocol, high-purity and ultra-thin nGOs have been obtained, as evidenced by X-ray diffraction (XRD) and transmission electron microscopy (TEM) investigations. The matrix-assisted pulsed laser evaporation (MAPLE) technique has been successfully employed to obtain the PLA-nGO-Zin coatings. The stoichiometric and uniform transfer was revealed by infrared microscopy (IRM) and scanning electron microscopy (SEM) studies. In vitro evaluation, performed on fresh blood samples, has shown the excellent hemocompatibility of PLA-nGO-Zin-coated samples (with a hemolytic index of 1.15%), together with their anti-inflammatory ability. Moreover, the PLA-nGO-Zin coatings significantly inhibited the development of mature bacterial biofilms, inducing important anti-biofilm efficiency in the as-coated samples. The herein-reported results evidence the promising potential of PLA-nGO-Zin coatings to be used for the biocompatible and antimicrobial surface modification of metallic implants.

Catalysts as Key Enablers for the Synthesis of Bioplastics with Sophisticated Architectures.

Bioplastics are one of the answers to environmental pollution and linear material flows. The most promising bioplastic polylactide (PLA) is already replacing conventional plastics in a number of applications. The properties of PLA, however, do not fit for all potential application areas, but they can be altered by the introduction of comonomers. The copolymerization of lactide (LA) with other lactones like ϵ-caprolactone (CL) has been established for several years. Nevertheless, controlling copolymerizations remains a challenge due to the high complexity of the system. Copolymerization of LA with other monomer classes is much less investigated, but has the chance to overcome the limitations in material properties that occur when only lactones are used. The crucial factor for all copolymerizations is the catalyst. It dominates the reaction kinetics and determines the resulting microstructure. In this review, copolymerization catalysts for LA are presented divided into catalysts for the synthesis of lactone block copolymers, lactone random copolymers, and multimechanistically synthesized copolymers. The selected catalysts are highlighted either owing to their industrially applicable polymerization conditions or their non-standard mechanism.

A Quantitative Study on Branching Density Dependent Behavior of Polylactide Melt Strength.

Polymer melt strength (MS) is strongly correlated with its molecular structure, while their relationship is not very clear yet. In this work, designable long-chain branched polylactide (LCB-PLA) is prepared in situ by using a tailor-made (methyl methacrylate)-co-(glycidyl methacrylate) copolymer (MG) with accurate number of reactive sites. A new concept of branching density (φ) in the LCB-PLA system is defined to quantitively study their relationship. Importantly, a critical point of φc  = 5.5 mol/104  mol C is revealed for the first time, below which the zero-shear viscosity (η0 ) corresponding to MS increases slowly with a slope of Δη0 /Δφ = 1400, while it increases sharply above this critical point due to entanglement of neighboring LCB-PLA chains. Consequently, the MS of PLA increased by >100 times by optimizing the LCB structures while maintaining processibility. Therefore, this work provides a deeper understanding and feasible route in quantitative design of polymers with high(er) melt strength for some specialty applications.

Development of a porous layer-by-layer microsphere with branched aliphatic hydrocarbon porogens.

Porous polymer microspheres are employed in biotherapeutics, tissue engineering, and regenerative medicine. Porosity dictates cargo carriage and release that are aligned with the polymer physicochemical properties. These include material tuning, biodegradation, and cargo encapsulation. How uniformity of pore size affects therapeutic delivery remains an area of active investigation. Herein, we characterize six branched aliphatic hydrocarbon-based porogen(s) produced to create pores in single and multilayered microspheres. The porogens are composed of biocompatible polycaprolactone, poly(lactic-co-glycolic acid), and polylactic acid polymers within porous multilayered microspheres. These serve as controlled effective drug and vaccine delivery platforms.

Acceleration of Electrospun PLA Degradation by Addition of Gelatin.

Biocompatible polyesters are widely used in biomedical applications, including sutures, orthopedic devices, drug delivery systems, and tissue engineering scaffolds. Blending polyesters with proteins is a common method of tuning biomaterial properties. Usually, it improves hydrophilicity, enhances cell adhesion, and accelerates biodegradation. However, inclusion of proteins to a polyester-based material typically reduces its mechanical properties. Here, we describe the physicochemical properties of an electrospun polylactic acid (PLA)-gelatin blend with a 9:1 PLA:gelatin ratio. We found that a small content (10 wt%) of gelatin does not affect the extensibility and strength of wet electrospun PLA mats but significantly accelerates their in vitro and in vivo decomposition. After a month, the thickness of PLA-gelatin mats subcutaneously implanted in C57black mice decreased by 30%, while the thickness of the pure PLA mats remained almost unchanged. Thus, we suggest the inclusion of a small amount of gelatin as a simple tool to tune the biodegradation behavior of PLA mats.

Graphene Oxide/RhPTH(1-34)/Polylactide Composite Nanofibrous Scaffold for Bone Tissue Engineering.

Polylactide (PLA) is one of the most promising polymers that has been widely used for the repair of damaged tissues due to its biocompatibility and biodegradability. PLA composites with multiple properties, such as mechanical properties and osteogenesis, have been widely investigated. Herein, PLA/graphene oxide (GO)/parathyroid hormone (rhPTH(1-34)) nanofiber membranes were prepared using a solution electrospinning method. The tensile strength of the PLA/GO/rhPTH(1-34) membranes was 2.64 MPa, nearly 110% higher than that of a pure PLA sample (1.26 MPa). The biocompatibility and osteogenic differentiation test demonstrated that the addition of GO did not markedly affect the biocompatibility of PLA, and the alkaline phosphatase activity of PLA/GO/rhPTH(1-34) membranes was about 2.3-times that of PLA. These results imply that the PLA/GO/rhPTH(1-34) composite membrane may be a candidate material for bone tissue engineering.

Nanocomposite Materials Based on Polylactide and Gold Complex Compounds for Absorbed Dose Diagnostics in BNCT.

In this study, approaches to the synthesis of complex compound of gold with cysteine [AuCys]n for measuring absorbed dose in boron neutron capture therapy (BNCT) were developed. The dependence of the complex particle size on pH were established. Nanocomposite materials based on polylactide containing [AuCys]n particles with an average size of about 20 nm were obtained using the crazing mechanism. The structure of obtained materials was studied by electron microscopy. The release kinetics of [AuCys]n from polymer matrix were investigated. Release of [AuCys]n from the volume of the polymeric matrix had a delayed start-this process began only after 24 h and was characterized by an effective rate constant of 1 µg/h from a 20 mg composite sample. At the same time, in vitro studies showed that the concentration of 6.25 µg/mL was reliably safe and did not reduce the survival of U251 and SW-620 cells.

Investigating the Properties and Characterization of a Hybrid 3D Printed Antimicrobial Composite Material Using FFF Process: Innovative and Swift.

Novel strategies and materials have gained the attention of researchers due to the current pandemic, the global market high competition, and the resistance of pathogens against conventional materials. There is a dire need to develop cost-effective, environmentally friendly, and biodegradable materials to fight against bacteria using novel approaches and composites. Fused filament fabrication (FFF), also known as fused deposition modeling (FDM), is the most effective and novel fabrication method to develop these composites due to its various advantages. Compared to metallic particles alone, composites of different metallic particles have shown excellent antimicrobial properties against common Gram-positive and Gram-negative bacteria. This study investigates the antimicrobial properties of two sets of hybrid composite materials, i.e., Cu-PLA-SS and Cu-PLA-Al, are made using copper-enriched polylactide composite, one-time printed side by-side with stainless steel/PLA composite, and second-time with aluminum/PLA composite respectively. These materials have 90 wt.% of copper, 85 wt.% of SS 17-4, 65 wt.% of Al with a density of 4.7 g/cc, 3.0 g/cc, and 1.54 g/cc, respectively, and were fabricated side by side using the fused filament fabrication (FFF) printing technique. The prepared materials were tested against Gram-positive and Gram-negative bacteria such as Escherichia coli (E. coli), Staphylococcus aureus (S. aureus), Pseudomonas aeruginosa (P. aeruginosa), Salmonella Poona (S. Poona), and Enterococci during different time intervals (5 min, 10 min, 20 min, 1 h, 8 h, and 24 h). The results revealed that both samples showed excellent antimicrobial efficiency, and 99% reduction was observed after 10 min. Hence, three-dimensional (3D) printed polymeric composites enriched with metallic particles can be utilized for biomedical, food packaging, and tissue engineering applications. These composite materials can also provide sustainable solutions in public places and hospitals where the chances of touching surfaces are higher.

Biofilm Formation and Genetic Diversity of Microbial Communities in Anaerobic Batch Reactor with Polylactide (PLA) Addition.

In this paper, an anaerobic digestion (AD) study was conducted on confectionery waste with granular polylactide (PLA) as a cell carrier. Digested sewage sludge (SS) served as the inoculum and buffering agent of systems. This article shows the results of the analyses of the key experimental properties of PLA, i.e., morphological characteristics of the microstructure, chemical composition and thermal stability of the biopolymer. The evaluation of quantitative and qualitative changes in the genetic diversity of bacterial communities, performed using the state-of-the-art next generation sequencing (NGS) technique, revealed that the material significantly enhanced bacterial proliferation; however, it does not change microbiome biodiversity, as also confirmed via statistical analysis. More intense microbial proliferation (compared to the control sample, without PLA and not digested, CW-control, CW-confectionery waste) may be indicative of the dual role of the biopolymer-support and medium. Actinobacteria (34.87%) were the most abundant cluster in the CW-control, while the most dominant cluster in digested samples was firmicutes: in the sample without the addition of the carrier (CW-dig.) it was 68.27%, and in the sample with the addition of the carrier (CW + PLA) it was only 26.45%, comparable to the control sample (CW-control)-19.45%. Interestingly, the number of proteobacteria decreased in the CW-dig. sample (17.47%), but increased in the CW + PLA sample (39.82%) compared to the CW-control sample (32.70%). The analysis of biofilm formation dynamics using the BioFlux microfluidic system shows a significantly faster growth of the biofilm surface area for the CW + PLA sample. This information was complemented by observations of the morphological characteristics of the microorganisms using fluorescence microscopy. The images of the CW + PLA sample showed carrier sections covered with microbial consortia.

Dispersant and Protective Roles of Amphiphilic Poly(ethylene phosphate) Block Copolymers in Polyester/Bone Mineral Composites.

Composites of synthetic bone mineral substitutes (BMS) and biodegradable polyesters are of particular interest for bone surgery and orthopedics. Manufacturing of composite scaffolds commonly uses mixing of the BMS with polymer melts. Melt processing requires a high homogeneity of the mixing, and is complicated by BMS-promoted thermal degradation of polymers. In our work, poly(L-lactide) (PLLA) and poly(ε-caprolactone) (PCL) composites reinforced by commercial ß-tricalcium phosphate (ßTCP) or synthesized carbonated hydroxyapatite with hexagonal and plate-like crystallite shapes (hCAp and pCAp, respectively) were fabricated using injection molding. pCAp-based composites showed advanced mechanical and thermal characteristics, and the best set of mechanical characteristics was observed for the PLLA-based composite containing 25 wt% of pCAp. To achieve compatibility of polyesters and pCAp, reactive block copolymers of PLLA or PCL with poly(tert-butyl ethylene phosphate) (C1 and C2, respectively) were introduced to the composite. The formation of a polyester-b-poly(ethylene phosphoric acid) (PEPA) compatibilizer during composite preparation, followed by chemical binding of PEPA with pCAp, have been proved experimentally. The presence of 5 wt% of the compatibilizer provided deeper homogenization of the composite, resulting in a marked increase in strength and moduli as well as a more pronounced nucleation effect during isothermal crystallization. The use of C1 increased the thermal stability of the PLLA-based composite, containing 25 wt% of pCAp. In view of positive impacts of polyester-b-PEPA on composite homogeneity, mechanical characteristics, and thermal stability, polyester-b-PEPA will find application in the further development of composite materials for bone surgery and orthopedics.

Overview of Antimicrobial Biodegradable Polyester-Based Formulations.

As the clinical complications induced by microbial infections are known to have life-threatening side effects, conventional anti-infective therapy is necessary, but not sufficient to overcome these issues. Some of their limitations are connected to drug-related inefficiency or resistance and pathogen-related adaptive modifications. Therefore, there is an urgent need for advanced antimicrobials and antimicrobial devices. A challenging, yet successful route has been the development of new biostatic or biocide agents and biomaterials by considering the indisputable advantages of biopolymers. Polymers are attractive materials due to their physical and chemical properties, such as compositional and structural versatility, tunable reactivity, solubility and degradability, and mechanical and chemical tunability, together with their intrinsic biocompatibility and bioactivity, thus enabling the fabrication of effective pharmacologically active antimicrobial formulations. Besides representing protective or potentiating carriers for conventional drugs, biopolymers possess an impressive ability for conjugation or functionalization. These aspects are key for avoiding malicious side effects or providing targeted and triggered drug delivery (specific and selective cellular targeting), and generally to define their pharmacological efficacy. Moreover, biopolymers can be processed in different forms (particles, fibers, films, membranes, or scaffolds), which prove excellent candidates for modern anti-infective applications. This review contains an overview of antimicrobial polyester-based formulations, centered around the effect of the dimensionality over the properties of the material and the effect of the production route or post-processing actions.

Effect of Acetylation of Two Cellulose Nanocrystal Polymorphs on Processibility and Physical Properties of Polylactide/Cellulose Nanocrystal Composite Film.

Polylactide (PLA) has become a popular alternative for petroleum-based plastics to reduce environmental pollution. The broader application of PLA is hampered by its brittle nature and incompatibility with the reinforcement phase. The aim of our work was to improve the ductility and compatibility of PLA composite film and investigate the mechanism by which nanocellulose enhances PLA polymer. Here, we present a robust PLA/nanocellulose hybrid film. Two different allomorphic cellulose nanocrystals (CNC-I and CNC-III) and their acetylated products (ACNC-I and ACNC-III) were used to realize better compatibility and mechanical performance in a hydrophobic PLA matrix. The tensile stress of the composite films with 3% ACNC-I and ACNC-III increased by 41.55% and 27.22% compared to pure PLA film, respectively. Compared to the CNC-I or CNC-III enhanced PLA composite films, the tensile stress of the films increased by 45.05% with 1% ACNC-I and 56.15% with 1% ACNC-III. In addition, PLA composite films with ACNCs showed better ductility and compatibility because the composite fracture gradually transitioned to a ductile fracture during the stretching process. As a result, ACNC-I and ACNC-III were found to be excellent reinforcing agents for the enhancement of the properties of polylactide composite film, and the replacement some petrochemical plastics with PLA composites would be very promising in actual life.

A New Self-Healing Degradable Copolymer Based on Polylactide and Poly(p-dioxanone).

In this paper, the copolymerization of poly (p-dioxanone) (PPDO) and polylactide (PLA) was carried out via a Diels-Alder reaction to obtain a new biodegradable copolymer with self-healing abilities. By altering the molecular weights of PPDO and PLA precursors, a series of copolymers (DA2300, DA3200, DA4700 and DA5500) with various chain segment lengths were created. After verifying the structure and molecular weight by 1H NMR, FT-IR and GPC, the crystallization behavior, self-healing properties and degradation properties of the copolymers were evaluated by DSC, POM, XRD, rheological measurements and enzymatic degradation. The results show that copolymerization based on the DA reaction effectively avoids the phase separation of PPDO and PLA. Among the products, DA4700 showed a better crystallization performance than PLA, and the half-crystallization time was 2.8 min. Compared to PPDO, the heat resistance of the DA copolymers was improved and the Tm increased from 93 °C to 103 °C. Significantly, the rheological data also confirmed that the copolymer was self-healing and showed obvious self-repairing properties after simple tempering. In addition, an enzyme degradation experiment showed that the DA copolymer can be degraded by a certain amount, with the degradation rate lying between those of PPDO and PLA.

Toughening Effect of 2,5-Furandicaboxylate Polyesters on Polylactide-Based Renewable Fibers.

This work presents the successful preparation and characterization of polylactide/poly(propylene 2,5-furandicarboxylate) (PLA/PPF) and polylactide/poly(butylene 2,5-furandicarboxylate) (PLA/PBF) blends in form of bulk and fiber samples and investigates the influence of poly(alkylene furanoate) (PAF) concentration (0 to 20 wt%) and compatibilization on the physical, thermal, and mechanical properties. Both blend types, although immiscible, are successfully compatibilized by Joncryl (J), which improves the interfacial adhesion and reduces the size of PPF and PBF domains. Mechanical tests on bulk samples show that only PBF is able to effectively toughen PLA, as PLA/PBF blends with 5-10 wt% PBF showed a distinct yield point, remarkable necking propagation, and increased strain at break (up to 55%), while PPF did not show significant plasticizing effects. The toughening ability of PBF is attributed to its lower glass transition temperature and greater toughness than PPF. For fiber samples, increasing the PPF and PBF amount improves the elastic modulus and mechanical strength, particularly for PBF-containing fibers collected at higher take-up speeds. Remarkably, in fiber samples, plasticizing effects are observed for both PPF and PBF, with significantly higher strain at break values compared to neat PLA (up to 455%), likely due to a further microstructural homogenization, enhanced compatibility, and load transfer between PLA and PAF phases following the fiber spinning process. SEM analysis confirms the deformation of PPF domains, which is probably due to a "plastic-rubber" transition during tensile testing. The orientation and possible crystallization of PPF and PBF domains contribute to increased tensile strength and elastic modulus. This work showcases the potential of PPF and PBF in tailoring the thermo-mechanical properties of PLA in both bulk and fiber forms, expanding their applications in the packaging and textile industry.

[Study of properties of three-dimensional matrices manufactured by antisolvent 3D printing for reconstruction of extensive bone defects in dentistry and maxillofacial surgery]. / Issledovanie svoistv trekhmernykh matrits, izgotovlennykh metodom antisol'ventnoi 3D-pechati, dlya vosstanovleniya obshirnykh kostnykh defektov v stomatologii i chelyustno-litsevoi khirurgii.

OBJECTIVE: The aim of the study to study of physical, mechanical and biocompatible properties of the matrices manufactured by antisolvent 3D printing from the solutions of polylactide-co-glycolide in tetraglycol. MATERIAL AND METHODS: Three-dimensional scaffolds were made from a solution of polylactide-co-glycolide mixed with tetraglycol using antisolvent 3D printing. The elastic properties and the structure of the obtained matrices were studied. MTT-test and staining with PKH-26, Calcein-AM, DAPI with subsequent fluorescence microscopy were used to study biological properties. RESULTS: The three-dimensional scaffolds had good mechanical properties. Young's modulus value was 18±2 MPa, tensile strength was 0.43±0.05 MPa. The relative survival rate of cells after the first day was 99.58±2.28%, on the 14th day - 98.14±2.22%. The structure of the scaffold promoted cell adhesion and spreading on its surface. CONCLUSION: The polylactide-co-glycolide matrices produced by antisolvent printing have high porosity, biocompatibility and good mechanical properties. It is allowed to use them in the future as a basis for personalized constructions for the replacement of extensive bone defects of the maxillofacial region.

Functionalization of Polylactide with Multiple Tetraphenyethane Inifer Groups to Form PLA Block Copolymers with Vinyl Monomers.

In the present contribution, a new strategy for preparing block copolymers of polylactide (PLA), a bio-derived polymer of increasing importance, is described. The method should lead to multiblock copolymers of lactide with vinyl monomers (VM), i.e., monomers that polymerize according to different mechanisms, and is based on the introduction of multiple "inifer" (INItiator/transFER agent) groups into PLA's structure. As an "inifer" group, tetraphenylethane (TPE, known to easily thermally dissociate to radicals) was incorporated into PLA chains using diisocyanate. PLA that contained TPE groups (PLA-PU) was characterized, and its ability to form initiating radicals was demonstrated by ESR measurements. PLA-PU was used as a "macroinifer" for the polymerization of acrylonitrile and styrene upon moderate heating (85 °C) of the PLA-PU in the presence of monomers. The formation of block copolymers PLA/PVM was confirmed by 1H NMR, DOSY NMR, and FTIR spectroscopies and the SEC method. The prepared copolymers showed only one glass transition in DSC curves with Tg values higher than those of PLA-PU.