Thermoluminescence studies of zinc borate (ZnB2 O4 ) phosphor doped with rare earths for dosimetric aspects.

A series of ZnB2 O4 phosphors doped with different concentrations of Eu and Dy (0.05 0.1, 0.2, 0.5, 1.0 mol%) and co-doped with Ce (1, 2, 5, 7, 10 mol%) respectively was prepared via the solid-state reaction technique and the thermoluminescence (TL) behaviour of gamma ray-irradiated samples was studied. The synthesized samples were irradiated with γ-rays for the dose range 0.03-1.20 kGy. The TL intensity variations with dose, dopant concentration, and the effect of co-doping were studied. The TL response curves for ZnB2 O4 :Eu3+ and ZnB2 O4 :Dy3+ , ZnB2 O4 :Eu3 ,Ce3+ and ZnB2 O4 :Dy3+ ,Ce3+ phosphor were observed. It was revealed that ZnB2 O4 :Eu3+ showed a linear TL behaviour for the dose 0.03-1.20 kGy and ZnB2 O4 :Dy3+ showed linearity for the gamma dose range 0.03-0.10 kGy. Furthermore, fading for all the samples was observed to be less than 10% for a storage period of 30 days. In addition to this, the trapping parameters, especially activation energies were evaluated using the Ilich method and the initial rise method. The activation energy values obtained from both methods were in complete agreement with each other.

In Situ Nitrogen Retention of Carbon Anode for Enhancing the Electrochemical Performance for Sodium-Ion Battery.

Retaining nitrogen for polyacrylonitrile (PAN) based carbon anode is a cost-effective way to make full use of the advantages of PAN for sodium-ion batteries (SIBs). Here, a simple strategy has been successfully adopted to retain N atoms in situ and increase production yield of a novel composite PAZ by mixing 3 wt % of zinc borate (ZB) with poly (acrylonitrile-co-itaconic acid) (PANIA). Among the prepared carbonised fibre (CF) samples, PAZ-CF-700 maintains the highest N content, retaining 90 % of the original N from PANIA. It represents the highest capacity storage contribution (80.55 %) and the lowest impedance Rct (117 Ω). Consequently, the specific capacity increases from 60 mAh g-1 of PANIA-CF-700 to 190 mAh g-1 of PAZ-CF-700 at a current density of 100 mA g-1 . At the same time, PAZ-CF-700 exhibits a good rate performance and excellent long-term cycling stability with a specific capacity of 94 mAh g-1 after 4000 cycles at 1.6 A g-1 .

Boosting Flame Retardancy of Polypropylene/Calcium Carbonate Composites with Inorganic Flame Retardants.

This study investigates the effects of inorganic flame retardants, zinc borate, and magnesium hydroxide, on the thermal, morphological, flame retardancy, and mechanical properties of polypropylene (PP)/calcium carbonate composites for potential construction industry applications. Polypropylene/calcium carbonate (50 wt.%) composites containing 5 and 10 wt.% flame retardants were prepared using a batch mixer, followed by compression moulding. The results demonstrated enhanced thermal stability, with the highest char residue reaching 47.2% for polypropylene/calcium carbonate/zinc borate (10 wt.%)/magnesium hydroxide (10 wt.%) composite, a notably strong outcome. Additionally, the composite exhibited an elevated limited oxygen index (LOI) of 29.4%, indicating a synergistic effect between zinc borate and magnesium hydroxide. The proposed flame retardancy mechanism suggests that the flammability performance is driven by the interaction between the flame retardants within the polypropylene/calcium carbonate matrix. Magnesium hydroxide contributes to smoke suppression by releasing water, while zinc borate forms a protective glassy foam that covers the burning surface, promoting char formation and acting as a physical barrier to heat transmission and fire spread. Scanning electron microscopy confirmed good dispersion of the additives alongside calcium carbonate within the polymer matrix. Despite the addition of up to 10 wt.% flame retardants, the composites maintained high-notched impact strength.

Boric acid and zinc borate doped graphene hydrogels designed for burn treatment: In vitro viability-biocompatibility tests and microbiological analysis.

Boron, an essential element for human, can be a key factor in wound healing. For this reason, in this study, role of boron products (boric acid and zinc borate) and boron product doped new synthesized graphene hydrogels was investigated for burn healing via in vitro viability-biocompatibility tests and microbiological analysis. It has been determined that boric acid and zinc borate are effective against microbial agents that are frequently seen in burns. In L929 mouse fibroblast cell line, BA, ZB and graphene hydrogels did not show any toxic effects, either alone or doped Graphene Hydrogel forms, except at very high doses. These substances showed antioxidant properties by protecting cells against H2O2 damage. The migration test performed on boron products also confirms the protective effect of boron products. In this study, the synthesis of graphene hydrogels was made for the first time, and their characterization was completed with appropriate instrumental analyses. The results of the biocompatibility tests of graphene hydrogels show that they are at least 96% biocompatible.

Activity of zinc oxide and zinc borate nanoparticles against resistant bacteria in an experimental lung cancer model.

BACKGROUND: Recent research indicates a prevalence of typical lung infections, such as pneumonia, in lung cancer patients. Klebsiella pneumoniae, Pseudomonas aeruginosa, and Acinetobacter baumannii stand out as antibiotic-resistant pathogens. Given this, there is a growing interest in alternative therapeutic avenues. Boron and zinc derivatives exhibit antimicrobial, antiviral, and antifungal properties. OBJECTIVES: This research aimed to establish the effectiveness of ZnO and ZB NPs in combating bacterial infections in lung cancer cell lines. METHODS: Initially, this study determined the minimal inhibitory concentration (MIC) and fractional inhibitory concentration (FIC) of zinc oxide nanoparticles (ZnO NPs) and zinc borate (ZB) on chosen benchmark strains. Subsequent steps involved gauging treatment success through a lung cancer-bacteria combined culture and immunohistochemical analysis. RESULTS: The inhibitory impact of ZnO NPs on bacteria was charted as follows: 0.97 µg/mL for K. pneumoniae 700603, 1.95 µg/mL for P. aeruginosa 27853, and 7.81 µg/mL for Acinetobacter baumannii 19,606. In comparison, the antibacterial influence of zinc borate was measured as 7.81 µg/mL for Klebsiella pneumoniae 700603 and 500 µg/mL for both P. aeruginosa 27853 and A.baumannii 19606. After 24 h, the cytotoxicity of ZnO NPs and ZB was analyzed using the MTT technique. The lowest cell viability was marked in the 500 µg/mL ZB NPs group, with a viability rate of 48.83% (P < 0.001). However, marked deviations appeared at ZB concentrations of 61.5 µg/mL (P < 0.05) and ZnO NPs at 125 µg/mL. CONCLUSION: A synergistic microbial inhibitory effect was observed when ZnO NP and ZB were combined against the bacteria under investigation.

Management of ground tire rubber waste by incorporation into polyurethane-based composite foams.

Rapid economic growth implicated the developing multiple industry sectors, including the automotive branch, increasing waste generation since recycling and utilization methods have not been established simultaneously. A very severe threat is the generation of enormous amounts of post-consumer tires considered burdensome waste, e.g., due to the substantial emissions of volatile organic compounds (VOCs). Therefore, it is essential to develop novel, environmentally friendly methods for their utilization, which would hinder their environmental impacts. One of the most promising approaches is shredding, resulting in the generation of ground tire rubber (GTR), which can be introduced into polymeric materials as filler. The presented work is related to the thermomechanical treatment of GTR in a twin-screw extruder with zinc borate, whose incorporation is aimed to enhance shear forces within the extruder barrel. Modified GTR was introduced into flexible polyurethane (PU) foams, and the impact of modification parameters on the cellular structure, static and dynamic mechanical performance, thermal stability, as well as thermal insulation, and acoustic properties was investigated. Emissions of VOCs from applied fillers and prepared composites were monitored and evaluated. Depending on the treatment parameters, beneficial changes in foams' cellular structure were noted, which enhanced their thermal insulation performance, mechanical strength, and thermal stability. It was proven that the proposed method of GTR thermomechanical treatment assisted by zinc borate particles might benefit the performance of flexible PU foamed composites and hinder VOC emissions, which could broaden the application range of GTR and provide novel ways for its efficient utilization.

Boron Compound-Based Treatments Against Multidrug-Resistant Bacterial Infections in Lung Cancer In Vitro Model.

Multidrug-resistant bacteria is one of the most important public health problems. Increasing rates of antibacterial resistance also affect the outcomes of medical approaches. Cancer treatment because of immune system deficiency (chemotherapy or steroids usage) commonly can cause infection. Lung cancer is the dominant cause of cancer-related deaths, and infection is the most common cause of death among those patients. In this study, it was aimed to determine the antimicrobial, antibiofilm, and anticancer activity of boron compounds. A549 lung cancer cell line was infected with Acinetobacter baumannii (ATCC 19606), Klebsiella pneumoniae (ATCC 700603), and Pseudomonas aeruginosa (ATCC 27853). In order to determine the fractional inhibitory concentration (FIC) index, antibiotics and boron compound concentrations prepared according to the minimum inhibitory concentration (MIC) values were determined by the checkerboard method. In our study results, the antibiofilm activity was an average of 46% in A. baumannii+boron compounds, 45% in P. aeruginosa+boron compounds, and 43% in K. pneumoniae. Cell culture analysis results show a decrease in viability and antioxidant capacity and an increase in total oxidant status after adding boron compounds to the culture. Immunofluorescence results show a correlation with MTT, and boron compounds increased 8-OHdG expression in comparison to antibiotic administration. In conclusion, boron compounds have promising effects on bacteria, especially in resistant bacteria spp.

Synthesis of Zinc Oxide Nanorods from Zinc Borate Precursor and Characterization of Supercapacitor Properties.

The synthesis of zinc oxide (ZnO) was accomplished from zinc borate (Zn3B2O6) minerals to be used as electrodes in supercapacitor applications. The concentrations of obtained zinc (Zn) metal after treatment with hydrochloric acid (HCl) were determined by atomic absorption spectroscopy (AAS). Direct synthesis of ZnO on a nickel (Ni) foam surface was conducted by employing the hydrothermal technique using a solution with the highest Zn content. The results showed the successful synthesis of ZnO nanorods on the surface of Ni foam with an average wall size of approximately 358 nm. Cyclic voltammetry (CV) and galvanostatic charge-discharge (GCD) measurements revealed that the synthesized electrode exhibited battery-type charge storage characteristics, reaching a maximum specific capacitance of approximately 867 mF·cm-² at a current density of 2 mA·cm-². Additionally, the energy and power densities of the electrode at a current density of 2 mA·cm-² were calculated as 19.3 mWh·cm-² and 200 mW·cm-², respectively. These results exhibited promising performance of the single-component electrode, outperforming the existing counterparts reported in the literature.

Flame Retardancy and Smoke Suppression of Silicone Rubber Foam with Microencapsulated Sepiolite and Zinc Borate.

The flame-retardant micro-encapsulated sepiolite (MSEP) was successfully prepared by sol-gel method. Fourier transform infrared, X-ray photoelectron spectroscopy, scanning electron microscopy, and energy dispersive spectroscopy were utilized to prove that sepiolite was encapsulated. Then, the mechanical properties, flame retardance, smoke suppression, and pyrolysis characteristics of silicone rubber foam (SiFs) with MSEP and zinc borate (ZB) were analyzed. The results indicated that the tensile and compressive properties of SiFs could evidently improve with the incorporation of MSEP/ZB. SiFs with 3 wt% MSEP and 6 wt% ZB could achieve an limiting oxygen index value of 30.9 vol% and UL-94 V-0 rating, the time to ignition was 64.7% above that of pure SiFs, the peak heat release rate and total heat release were 42.7% and 25.0% lower than that of pure SiFs, respectively. Furthermore, the peak smoke production rate and total smoke production of SiFs with 3 wt% MSEP and 6 wt% ZB were merely 54.22% and 64.10% of pure SiFs. Especially, the thermal stability of SiFs was significantly enhanced, and the carbon residue of SiFs became denser and more complete after adding 3 wt% MSEP and 6 wt% ZB.

Ecotoxicity Study of Additives Composed of Zinc and Boron.

The high use of additives containing zinc borate and their limited solubility in water both lead to its persistence and accumulation in biological systems. On the other hand, soluble forms of boron are easily available to plant roots and are taken up by plants. There are no ecotoxicological data available for zinc borate, the industrial utilization of which is widespread. Therefore, the potential toxicity of zinc borate and its dissociated compounds was evaluated. Based on two different ecotoxicology tests, their effect on plant growth was studied. Firstly, the impact on Lemna minor growth was investigated, including the effect on pigment content. Secondly, the inhibition of the root growth of higher plant species Sinapis alba (mustard), Lactuca sativa (lettuce) and Trifolium pretense (clover) was measured. The growth inhibition test on L. minor was more complex and sensitive compared to the plant seed germination test. Already low concentrations (10 mg/L) of ZnO, B2O3 and Zn3BO6 led to a decrease in frond growth and to an inhibition of the conversion of chlorophyll a to chlorophyll b. These results suggested that the stress caused by these additives caused damage to the photosynthetic apparatus. The highest inhibition of frond growth was detected in fronds treated with B2O3 (92-100%). In ZnO and Zn3BO6, the inhibition of frond growth was between 38 and 77%, with Zn3BO6 being slightly more toxic. In the seed germination test, the most sensitive species was lettuce, the growth of which was inhibited by 57, 83 and 53% in ZnO, B2O3 and Zn3BO6 treatments, respectively. However, the inhibitory effect on each plant was different. In lettuce and clover, the seed germination and root elongation decreased with increasing element concentrations. In contrast, in mustard, low concentrations of ZnO and Zn3BO6 supported the growth of roots. For that reason, more complex tests are essential to evaluate the additive toxicity in the environment.

Molecular Genetics and Cytotoxic Responses to Titanium Diboride and Zinc Borate Nanoparticles on Cultured Human Primary Alveolar Epithelial Cells.

Titanium diboride (TiB2) and zinc borate (Zn3BO6) have been utilized in wide spectrum industrial areas because of their favorable properties such as a high melting point, good wear resistance, high hardness and thermal conductivity. On the other hand, the biomedical potentials of TiB2 and Zn3BO6 are still unknown because there is no comprehensive analysis that uncovers their biocompatibility features. Thus, the toxicogenomic properties of TiB2 and Zn3BO6 nanoparticles (NPs) were investigated on human primary alveolar epithelial cell cultures (HPAEpiC) by using different cell viability assays and microarray analyses. Protein-Protein Interaction Networks Functional Enrichment Analysis (STRING) was used to associate differentially expressed gene probes. According to the results, up to 10 mg/L concentration of TiB2 and Zn3BO6 NPs application did not stimulate a cytotoxic effect on the HPAEpiC cell cultures. Microarray analysis revealed that TiB2 NPs exposure enhances cellular adhesion molecules, proteases and carrier protein expression. Furthermore, Zn3BO6 NPs caused differential gene expressions in the cell cycle, cell division and extracellular matrix regulators. Finally, STRING analyses put forth that inflammation, cell regeneration and tissue repair-related gene interactions were affected by TiB2 NPs application. Zn3BO6 NPs exposure significantly altered inflammation, lipid metabolism and infection response activator-related gene interactions. These investigations illustrated that TiB2 and Zn3BO6 NPs exposure may affect different aspects of cellular machineries such as immunogenic responses, tissue regeneration and cell survival. Thus, these types of cellular mechanisms should be taken into account before the use of the related NPs in further biomedical applications.

In-Silico Monte Carlo Simulation Trials for Investigation of V2O5 Reinforcement Effect on Ternary Zinc Borate Glasses: Nuclear Radiation Shielding Dynamics.

In the current study, promising glass composites based on vanadium pentoxide (V2O5)-doped zinc borate (ZnB) were investigated in terms of their nuclear-radiation-shielding dynamics. The mass and linear attenuation coefficient, half-value layer, mean free path, tenth-value layer, effective atomic number, exposure-buildup factor, and energy-absorption-buildup factor were deeply simulated by using MCNPX code, Phy-X PSD code, and WinXcom to study the validation of ZBV1, ZBV2, ZBV3, and ZBV4 based on (100-x)(0.6ZnO-0.4B2O3)(x)(V2O5) (x = 1, 2, 3, 4 mol%) samples against ionizing radiation. The results showed that attenuation competencies of the studied glasses slightly changed while increasing the V2O5 content from 1 mol% to 4 mol%. The domination of ZnO concentration in the composition compared to B2O3 makes ZnO substitution with V2O5 more dominant, leading to a decrease in density. Since density has a significant role in the attenuation of gamma rays, a negative effect was observed. It can be concluded that the aforementioned substitution can negatively affect the shielding competencies of studied glasses.

Effect of surfactant types on particle size and morphology of flame-retardant zinc borate powder.

Zinc borate is a boron-containing chemical material that is used to increase the flame retardancy of polymeric materials, dyes, cables, fabrics, carpets, and the internal parts of automobiles and planes. Commercially used zinc borate, which has the formula of 2ZnO·3B 2 O 3 ·7H 2 O, has a particle size between 10 and 20 µm. However, recent studies have shown that nanosized flame retardants have more superior flame retardancy and less negative effects on mechanical properties than microsized flame retardants. Nanosized flame retardants disperse more homogeneously and even low quantities are sufficient to provide high flame resistance. In this study, nano zinc borate powder was synthesized by a wet chemical method and the effects of nonionic, anionic, and cationic surfactants on the particle size and morphology of the zinc borate particles were investigated. Chemical purity and physical structures of the synthesized zinc borate powder were analyzed by XRD, FTIR, TG-DTA, TEM, and Zetasizer. The analysis results showed that the zinc borate powder had a chemical formula of 2ZnO·3B 2 O 3 ·7H 2 O. TEM and Zetasizer results indicated that the nano zinc borate powder, which had nanoscale particle size distribution with needle- and flake-like structures, was synthesized using nonionic, anionic, and cationic surfactants.

Effect of the B:Zn:H2O Molar Ratio on the Properties of Poly(Vinyl Acetate) and Zinc Borate-Based Intumescent Coating Materials Exposed to a Quasi-Real Cellulosic Fire.

In order to investigate an influence of the B:Zn:H2O molar ratio on the fire protection efficiency of poly(vinyl acetate)-based thermoplastic intumescent coating materials (ICs), systems containing ammonium polyphosphate, melamine, pentaerythritol and different types of zinc borates (ZBs) were tested in a vertical position in quasi-real fire conditions. 3ZnO·2B2O3·6H2O (ZB6), 2ZnO·3B2O3·3.5H2O (ZB3.5) or 3ZnO·2B2O3 (ZB0) were added in amounts of 1-10 wt. parts/100 wt. parts of the other coating components mixture. Char formation processes and thermal insulation features were investigated using an open-flame furnace heated according to the cellulosic fire curve. Thermogravimetric features (DTG), chemical structures (FTIR) and mechanical strength of the ICs and the chars were analyzed as well. It was revealed that the type and dose of the ZBs significantly affect thermal insulation time (TIT) (up to 450 °C of a steel substrate) and sagging (SI) of the fire-heated coatings as well as the compressive strength of the created chars. The highest TIT value (+89%) was noted for the sample with 2.5 wt. parts of ZB3.5 while the lowest SI (-65%) was observed for the coatings containing 10 wt. parts of the hydrated borates (i.e., ZB3.5 or ZB6). The best mechanical strength was registered for the sample filled with the anhydrous modifier (3 wt. parts of ZB0). The presented results show that the ICs with the proper ZBs can be used for effective fire protection of vertically positioned steel elements.

Determination of thermoluminescence properties of ZnB2O4:Tm3+,Li+ for dosimetric purposes.

This study aims to investigate the comparison of the thermoluminescence (TL) emission of Li+ and Tm3+ co-doped and un-doped zinc borate (ZnB2O4) phosphors prepared by wet chemical synthesis method. The crystal structure of the samples has been determined by means of X-ray powder diffraction and matched with the standard pattern of ZnB2O4 (PDF Card No. 039-1126). TL glow curves of 5 Gy beta irradiated Li+ (at different concentrations of 0.2, 0.5, 0.8 and 1.0%) and Tm3+ (1.0%) co-doped ZnB2O4 have been recorded using various band pass filters to determine both the optimum concentration and the suitable filter. The TL green emission (565 nm) of Li+ (1.0%), Tm3+ (1.0%) co-doped ZnB2O4 phosphor displays a complex structure where one can distinguish, at least, three groups of components peaked at 69, 166 and 291 °C where the more suitable dosimetric maxima appears at higher temperature. It could be observed how the 166 and 291 °C TL glow maxima of this material exhibits (i) good linearity in the range of 0.11-15 Gy, (ii) a minimum detectable dose value of 1.11 mGy, (iii) does not modify significantly the TL emission in shape and intensity after reusability (10 cycles) and (iv) a negligible fading effect for 5 Gy irradiated aliquots stored in darkness and room temperature up to 169 h. Additionally, it could be found that (v) kinetic parameters estimated by using variable heating rate method of Hoogenstraaten and initial rise method give similar results.

Termite resistance of MDF panels treated with various boron compounds.

In this study, the effects of various boron compounds on the termite resistance of MDF panels were evaluated. Either borax (BX), boric acid (BA), zinc borate (ZB), or sodium perborate tetrahydrate (SPT) were added to urea-formaldehyde (UF) resin at target contents of 1%, 1.5%, 2% and 2.5% based on dry fiber weight. The panels were then manufactured using 12% urea-formaldehyde resin and 1% NH(4)Cl. MDF samples from the panels were tested against the subterranean termites, Coptotermes formosanus Shiraki. Laboratory termite resistance tests showed that all samples containing boron compounds had greater resistance against termite attack compared to untreated MDF samples. At the second and third weeks of exposure, nearly 100% termite mortalities were recorded in all boron compound treated samples. The highest termite mortalities were determined in the samples with either BA or BX. Also, it was found that SPT showed notable performance on the termite mortality. As chemical loadings increased, termite mortalities increased, and at the same time the weight losses of the samples decreased.

Thermal Decomposition and Ceramifying Process of Ceramifiable Silicone Rubber Composite with Hydrated Zinc Borate.

The ceramifiable silicone rubber composite was prepared using hydrated zinc borate and kaolin as ceramifiable fillers. Effects of the hydrated zinc borate content and the combustion temperature on the properties of the ceramifiable silicone rubber composite were investigated. Thermal decomposition and ceramifying processes of the composite in a muffle furnace under air were also studied. The results showed that the density and the hardness of the composites increased as the content of the hydrated zinc borate increased from 0 to 30 phr. The tensile strength and elongation at break decreased. In addition, hydrated zinc borate decreased the decomposition temperature of the composite, whereas the residue weight under air atmosphere was increased. In the process of decomposition and oxidation of the ceramifiable silicone rubber composite in air, B2O3 was generated by the decomposition of zinc borate and participated in the formation of the residue network structure, which decreased the temperature of the ceramifying transition. The new phases, zinc aluminate (ZnO·Al2O3) and aluminum-rich mullite (9Al2O3·2SiO2), appeared after high-temperature thermochemical reactions. Microscopy images revealed that different structures were formed at different temperatures. The network structure of the ceramic residue became increasingly compact, and the compressive strength increased from 0.31 to 1.82 MPa with the increase of temperature from 800 to 1400 °C, which had a better protective effect on heat transfer and mass loss. The weight loss and the linear shrinkage of the ceramic residue was 37.6% and 21.9%, respectively, with the 30 phr content of hydrated zinc borate. The bending strength was improved from 0.11 to 11.58 MPa, and the compressive strength also increased from 0.03 to 1.14 MPa.

Simultaneously Improved Flame Retardance and Ceramifiable Properties of Polymer-Based Composites via the Formed Crystalline Phase at High Temperature.

Ceramifiable polyolefin materials have an excellent application prospect in high-temperature-resistant wires and cables because of their excellent fire safety performance via a ceramization process under fire conditions. During the ceramization process, the control of the crystalline phase plays a vital role in determining the final fire resistance and ceramifiable properties. In this work, ammonium polyphosphate/zinc borate (APP/ZB) was developed to achieve the highly efficient flame retardance and ceramization of the ethylene-vinyl acetate/mica powder/organo-modified montmorillonite (EVA/MP/OMMT) composite. In the combustion test, the EVA/MP/OMMT/APP/ZB system displayed obvious flame retardance feature, showing much lower total heat release and total smoke production than neat EVA. After treating at high temperatures, rigid ceramic products were formed for EVA/MP/OMMT/APP/ZB. The ceramic that was formed at 900 °C had a flexural strength of 10.3 MPa for EVA/MP/OMMT/APP/ZB containing 23 wt % of APP/ZB (9.9:13.1), increased by 2475.0, 635.7, and 586.7% compared to the corresponding values of EVA/MP/OMMT, EVA/MP/OMMT/ZB, and EVA/MP/OMMT/APP. For the latter two systems, the content of ZB or APP was 23 wt %. APP/ZB showed a remarkable fluxing effect on the ceramization of the MP-based EVA composite. The fluxing mechanism of APP/ZB was revealed by different measurements. Both APP and ZB led to the formation of a glass melt containing α-Zn3(PO4)2 and orthophosphate by increasing the temperature. Successively, the melt crystalline structure cohered the OMMT and MP together, accompanied by the gradual disappearance of the mica phase and the generation of eutectic phenomenon. Finally, a ceramic with high flexural strength was formed, leading to the improved flame retardance and ceramifiable properties of EVA-based composites.

Ammonium Polyphosphate Intercalated Layered Double Hydroxide and Zinc Borate as Highly Efficient Flame Retardant Nanofillers for Polypropylene.

We found in our previous study that layered double hydroxides (LDHs) which undergo aqueous miscible organic solvent treatment (AMOST) can tune the hydrophobicity surface of LDHs to be hydrophobic, and then the solvent mixing method can be used to prepare polymer/LDH nanocomposites. However, flame retardant property is not very high if LDHs are only used. In this present work, ammonium polyphosphate (APP) intercalated LDHs and zinc borate (ZB) was incorporated into a polypropylene (PP) matrix using the solvent mixing method. The structures, morphologies, and performance of the composites were characterized carefully. The peak heat release rate (PHRR) reduction of PP containing 10 and 20 wt % APP-LDH reached 27% and 55%, respectively, which increased up to 63% compared with PP/CO3-LDH. After incorporating 2 wt % ZB in the PP/APP-LDH system, the flame retardant property was further improved. Polypropylene composites with 20 wt % APP-LDH and 2 wt % ZB showed a 58% PHRR reduction. In addition, thermogravimetric analyzer (TGA) results indicated that the addition of APP-LDH and ZB improved the temperature at 50% weight loss (T50%) and the char formation of the materials significantly.

Development of a novel bioactive glass suitable for osteosarcoma-related bone grafts.

In this study, zinc borate-based glasses with increasing gallium content (0, 2.5, 5, 10, and 15 wt % Ga) were synthesized and their effect on the viability and proliferation of preosteoblasts and osteosarcoma cancer cells were investigated. Methyl thiazolyl tetrazolium (MTT) cell viability assays using glass degradation extracts revealed that the extracts from glasses with lower Ga contents could enhance the viability of preosteoblasts, while extracts from the glass composition with 15 wt % Ga caused statistically significant reduction of their viability. MTT cell viability assays using the extracts and osteosarcoma cells showed that only extracts from the glass composition with 5 wt % Ga (G3) did not cause a statistically significant increase in the viability of cancer cells for all degradation periods (1 day, 7 days, and 28 days). G3 was selected as the most suitable composition for the osteosarcoma-related graft operations as it could improve the viability of preosteoblasts without increasing the viability of cancer cells. The viability of preosteoblasts and osteosarcoma cells in contact with the glass powders were also investigated using MTT assays. The results showed that the G3 powders could enhance the viability of preosteoblasts while decreasing the viability of osteosarcoma cells. Finally, live/dead assays revealed that suppression of proliferation appeared to be the mechanism causing the observed reductions in the viability of osteosarcoma cells exposed to G3 powders. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 1186-1193, 2018.