Evaluation of bond strength between zirconia milled ceramic material and veneered dental porcelain.

This study aimed at examining the bond strength between zirconia and ceramic veneer, following the ISO 9693 guidelines. A total of fifty specimens of zirconia/ceramic-veneer system were produced using two commercial zirconias (VITA YZ-HTWhite and Zolid HT+ White, referred to as Group A and Group B, respectively) and a ceramic-veneering material (Zirkonia 750). The microstructure (via x-ray diffraction analysis, XRD and Secondary Electron mode, SEM) and the mechanical properties (via 3-point bending tests) of the two groups were assessed. Then, experiments were conducted according to the ISO 9693 and conventional protocols applied for producing zirconia/ceramic-veneer restorations. Bond strength values, measured by 3-point bending tests, were 34.42 ± 7.60 MPa for Group A and 31.92 ± 6.95 MPa for Group B. SEM observations of the cohesively fractured surfaces (on the porcelain side) and the examination for normality using the Shapiro-Wilk test suggested the use of Weibull statistical analysis. Median strength (σ50%) for Group A and Group B was 34.76 and 32.22 MPa, while the characteristic strength (σ63.2%) was 35.78 and 33.14 MPa, respectively. The Weibull modulus disparity between groups (12.69 and 13.07) was not significant. Bond strength exceeded the ISO 9693 minimum of 20 MPa, suggesting satisfactory strength for clinical use.

Occlusal veneer restoration treatment outcomes of cracked tooth syndrome: A 22.4-month follow-up study.

OBJECTIVES: The aims of this clinical study were to investigate success rate, vital pulp survival rate, tooth survival rate and patient-reported masticatory ability by evaluating the pain symptoms and signs of the cracked teeth as well as Index of Eating Difficulty (IED) and Oral Health Impact Profile-14 (OHIP-14) questionnaire after cracked teeth were restored with occlusal veneers. MATERIALS AND METHODS: 27 cracked teeth of 24 patients with cold and/or biting pains without spontaneous/nocturnal pains were recruited in this study. The cracked teeth were restored with occlusal veneers fabricated by lithium disilicate ceramic. Cold test and biting test were used to evaluate pain signs. IED and OHIP-14 questionnaire were used to evaluate masticatory ability. FDI criteria was used to evaluate restorations. The paired Wilcoxon test was used to analyze significant differences of detection rate of pain signs, OHIP scores and IED grade before and after restorations. Kaplan-Meier survival curve was used to describe the success rate, vital pulp survival rate, and tooth survival rate. RESULTS: 27 cracked teeth were restored with occlusal veneers with average of 22.4-month follow-up. Two cracked teeth had pulpitis and pain signs of the other cracked teeth completely disappeared. OHIP total scores were significantly reduced after treatment. Scores of 'pain', 'occlusal discomfort', 'uncomfortable to eat', 'diet unsatisfactory' and 'interrupted meals' reduced significantly after treatment. After treatment, IED grades of 25 vital teeth were significantly lower than those before treatment. FDI scores of 25 restorations except for 2 teeth with pulpitis were no greater than 2. The 12 months accumulated pulp survival rate of the cracked teeth was 92.6%. The 12 months accumulated tooth survival rate was 100%. The success rate at the latest recall was 92.6%. CONCLUSION: Occlusal veneer restorations with success rate of 92.6% and the same pulp survival rate might be an effective restoration for treating the cracked teeth. CLINICAL RELEVANCE: The occlusal veneer restorations might be an option for treating the cracked teeth when cracks only involve enamel and dentin, not dental pulp.

Laboratory study of fracture resistance and failure mode of porcelain laminate veneers with different preparation depths in endodontically treated teeth.

PURPOSE: To compare the fracture resistance and failure mode of porcelain laminate veneers with different preparation depths in endodontically treated teeth. METHODS: Root canal treatment was performed for 40 maxillary central incisors, and then the teeth were divided into four groups (n= 10). The preparation depths were as follows: Group A: 0.9 mm, Group B: 0.6 mm, Group C: 0.3 mm, and in all three groups, 2 mm butt joint incisal reductions were performed; Group D was a control group with no preparation. Then 30 lithium disilicate porcelain veneers were milled by CAD- CAM method and cemented. After that, all specimens were subjected to cyclic loading and thermal cycling and finally were tested by a universal testing machine until failure occurred. RESULTS: The mean failure loads (N) after exposure to continuous load were as follows: Group A: 625.70 (401.45-1037.77), Group B: 780.32 (222.93-1391.82), Group C: 748.81 (239.68-1241.87) and Group D (control) : 509.88 (84.42-1025.85) and P= 0.216. Analysis of failure mode in four groups showed that P= 0.469. There was no significant difference between the control and the other groups. In this study, 0.3, 0.6 and 0.9 mm depths of preparation for porcelain laminate veneers for endodontically treated teeth had no significant difference in fracture resistance and failure mode with non-prepared teeth. CLINICAL SIGNIFICANCE: Reasonable consideration might be given to porcelain laminate veneer treatment for teeth that have become discolored and resistant to bleaching (such as instances where discoloration is severe following root canal treatment). This approach is considered to be on the conservative side, and has demonstrated that a labial preparation depth reduction of up to 0.9 mm does not have any impact on the failure mode or fracture resistance of endodontically-treated teeth.

Ceramic veneer shade evaluation using a multicolored 3D-printed model-A case report.

OBJECTIVE: This article demonstrates the use of a multicolored 3D-printed model for laboratory shade evaluation of ceramic veneers. CLINICAL CONSIDERATIONS: A young female patient presented with peg lateral incisors and diastemata between her maxillary incisors. Four ceramic veneers for her maxillary incisors were fabricated using a digital workflow. A multicolored 3D-printed model was manufactured using material jetting technology. The multicolored model and try-in pastes were used to evaluate and adjust the shade of the veneers. Clinically acceptable color matching was achieved, the veneers were delivered without further chairside shade adjustments. CONCLUSIONS: Successful color evaluation and adjustment were achieved using the combination of multicolored 3D-printed model and try-in pastes. The use of this approach saved time for stump shade taking and fabrication of tooth-colored dies. CLINICAL SIGNIFICANCE: A multicolored 3D-printed model can be a useful tool for color evaluation and adjustment of ceramic restorations.

3D printing of ultra-thin veneers made of lithium disilicate using the LCM method in a digital workflow: A feasibility study.

OBJECTIVE: This article highlights the feasibility of the additive fabrication of ultra-thin veneers made of lithium disilicate using the lithography-based ceramic manufacturing (LCM) method. CLINICAL CONSIDERATIONS: An esthetical appealing restoration of anterior teeth with thin ceramic veneers is considered one of the ultimate challenges in restorative dental prosthetics. These sophisticated restorations can be fabricated in different ways. Both analog and digital subtractive manufacturing processes have been used to date. Either of the methods is highly demanding for the dental technician and dental engineering due to the required low ceramic layer thickness. CONCLUSION: Modern additive manufacturing methods, for example LCM technology, enable the production of ultra-thin lithium disilicate veneers with layer thicknesses of down to 0.2 mm and could therefore represent a viable alternative for this indication in the future. CLINICAL SIGNIFICANCE: Digital technologies can help streamline workflows, make the outcome more predictable and reproducible, and even further optimize therapeutic restorative options such as highly esthetic veneers for anterior teeth. The reduced material thickness allows for a true non-prep solution or minimally invasive preparation.

Quo vadis, esthetic dentistry? Part II: Composite resin overtreatment and social media appeal.

OBJECTIVES: This article presents case reports highlighting over-treatments with resin composites, often misconceived as minimally invasive procedures. CLINICAL CONSIDERATIONS: Tooth-colored restorative materials, such as ceramics and composites, have found widespread application to correct problems related to tooth color, shape, and alignment. When composite resin is used, these procedures can be done in a very conservative, cost-effective, and timely fashion. However, it is noteworthy that contemporary dental esthetic expectations are based on standards propagated by social media and other marketing and communications platforms. The abuse of and addiction to social media impacts can lead to unrealistic esthetic expectations and standards for both patients and dentists. CONCLUSIONS: After a critical discussion on ceramic veneers published in part I of this 2-part series, this article directs attention towards what has become a trendy fashion, i.e., the use of direct composite resins as "non-prep" veneers in clinical situations that arguably required no restorative intervention at all. We further explore how social media influences the decision-making processes of both professionals and patients.

Evaluation of marginal and internal adaptation of veneers generated by the guided prosthetic tooth preparation system.

OBJECTIVE: This in vitro study aimed to assess and contrast the marginal and internal adaptation of all-ceramic prefabricated veneers manufactured via the FirstFit guided tooth preparation system against all-ceramic veneers produced using the chairside Computer-Aided Design/Computer Aided Manufacture (CAD/CAM) system following identical guided preparation protocols. MATERIALS AND METHODS: Two main groups were included, with 16 lithium disilicate veneers per group. Four typodonts were used for the test (FirstFit) and control CAD/CAM groups. Intraoral scans created master casts and preparation guides. Guides performed preparations on typodont teeth (two central incisors and two lateral incisors). Prepared teeth were scanned (CEREC Omnicam) to design and mill CAD/CAM veneers. Marginal gap thickness and cement space thickness were measured using light microscopy at four locations: marginal, cervical internal, middle internal, and incisal internal. RESULTS: No significant difference existed between groups for marginal adaptation (p = 0.058) or incisal internal adaptation (p = 0.076). The control group had significantly lower values for middle internal adaptation (p = 0.023) and cervical internal adaptation (p = 0.019). CONCLUSIONS: Guided preparation evaluation showed no significant differences in marginal or incisal internal adaptation. The CAD/CAM group had significantly lower middle and cervical internal adaptation values.

Influence of ceramic thickness and dental substrate on the survival rate and failure load of non-retentive occlusal veneers after fatigue.

OBJECTIVE: To investigate the effect of ceramic thickness and dental substrate (enamel vs. dentin/enamel) on the survival rate and failure load of non-retentive occlusal veneers. MATERIALS AND METHODS: Human maxillary molars (n = 60) were divided into five test-groups (n = 12). The groups (named DE-1.5, DE-1.0, DE-0.5, E-1.0, E-0.5) differed in their dental substrate (E = enamel, DE = dentin/enamel) and restoration thickness (standard: 1.5 mm, thin: 1.0 mm, ultrathin: 0.5 mm). All teeth were prepared for non-retentive monolithic lithium-disilicate occlusal veneers (IPS e.max Press, Ivoclar). Restorations were adhesively cemented (Syntac Classic/Variolink II, Ivoclar) and exposed to thermomechanical fatigue (1.2 million cycles, 1.6 Hz, 49 N/ 5-55°C). Single load to failure was performed using a universal testing-machine. A linear-regression model was applied, pairwise comparisons used the Student-Newman-Keuls method (p < 0.05). RESULTS: Three dentin-based occlusal veneers (one DE-1.0, two DE-0.5) revealed cracks after fatigue exposure, which corresponds to an overall-survival rate of 95%. Load to failure resulted in the following ranking: 2142 N(DE-0.5) > 2105 N(E-1.0) > 2075 N(E-0.5) > 1440 N(DE-1.5) > 1430 N(DE-1.0). Thin (E-1.0) and ultrathin enamel-based occlusal veneers (E-0.5) revealed high failure loads and surpassed the standard thickness dentin-based veneers (DE-1.5) significantly (p = 0.044, p = 0.022). CONCLUSION: All tested monolithic lithium disilicate occlusal veneers obtained failure loads above physiological chewing forces. Thin and ultrathin enamel-based occlusal veneers outperformed the standard thick dentin-based occlusal veneers. CLINICAL SIGNIFICANCE: Minimally invasive enamel-based occlusal veneer restorations with non-retentive preparation design may serve as a conservative treatment option.

Fluorescence intensity of composite resin for direct veneer removal using a fluorescence-aided identification technique.

OBJECTIVES: This laboratory study evaluated the influence of the fluorescence intensity of composite resins on additional tooth wear and the presence of restorative material in different dental thirds during the retreatment of direct veneers. MATERIALS AND METHODS: The crown dimensions of 60 bovine incisors were reduced to 10 × 8 mm. The teeth were classified according to the fluorescence intensity of the composites: low (LOW) (TPH Spectra), medium (MED) (Opallis), and high (HIGH) (Essentia) groups. The teeth were divided according to the removal methods: conventional (CON) and fluorescence-aided identification technique (FIT). The specimens were scanned (T0), received veneer preparation, and scanned again (T1). After restorations, the composites were removed and the teeth were scanned (T2). Measurement assessments between T1 and T2 were performed to determine additional wear, presence of residual areas, and the average between additional wear and the presence of residual areas. Kruskal Wallis, Mann-Whitney, Friedman, 2-way ANOVA, and post-Tukey tests were performed (α < 0.05). RESULTS: The comparison of composite resins indicated a smaller area of additional wear and greater residue presence in the HIGH group than the LOW group for both techniques in the cervical third. Regarding removal methods, the FIT produced greater additional wear than the CON method for the LOW and MED groups in the middle and cervical thirds. The incisal third exhibited greater additional wear than the other thirds. CONCLUSIONS: Composite resins with high fluorescence intensity removed using FIT had less tooth wear. The incisal third was the most affected area for direct veneer removal procedures. CLINICAL SIGNIFICANCE: A FIT has been proposed for composite resin removal; however, the different fluorescence intensities of composite resins can influence tooth wear caused during this procedure.

Preparation of ultrathin translucent zirconia laminate veneers using 3D printing reduction guides.

Minimizing and controlling the amount of tooth reduction during the preparation of ultrathin laminate veneers is a challenge for minimally invasive dentistry. The use of reduction guides is advised to reach the optimal space required for the definitive restoration without excessive reduction. The digital production of a reduction guide used to control tooth preparation for ultrathin laminate veneers is described.

Effect of a modified laminate veneer preparation design on absolute margin discrepancy and marginal overhang.

STATEMENT OF PROBLEM: Veneer preparation designs impact veneer accuracy. However, whether a modified design could reduce absolute margin discrepancy and marginal overhangs is unclear. PURPOSE: The purpose of this in vitro study was to investigate whether a modified veneer preparation design enhances the absolute margin discrepancy and marginal overhang. MATERIAL AND METHODS: The absolute margin discrepancy and the marginal overhang of 3 different veneer preparation designs on a typodont tooth (n=20): feather edge, shoulder, and shoulder with wings were measured. The feather edge design was prepared first and subsequently modified to create the shoulder and shoulder with wings preparations. Ceramic veneers were fabricated using computer-aided design and computer-aided manufacture with each veneer assessed for fit before cementation. Ten specimens were cut vertically, and 10 were cut horizontally in each group. The absolute margin discrepancy and marginal overhangs were measured for each cross-section with scanning electron microscopy. Descriptive data analysis and hypothesis testing were conducted using the nonparametric Kruskal Wallis test (α=.05). RESULTS: On the vertical sections, the shoulder with wings preparation had the best absolute margin discrepancy and overhang. The design was also best for mesial overhang and mesial absolute margin discrepancy when measuring horizontally. CONCLUSIONS: The shoulder with wings preparation design produced the smallest cervical absolute margin discrepancy and overhang. This design also produced absolute margin discrepancy and overhangs comparable with those of the shoulder design in the proximal areas.

Stress distribution on teeth restored with veneers using various incisal preparation designs: A 3D finite element analysis study.

STATEMENT OF PROBLEM: The type of veneer preparation is often chosen according to the patient's tooth structure and occlusion. Taking biomechanics into account in this decision-making process provides the clinician with more technical information on how to improve the clinical longevity of restorations. However, biomechanical analyses of veneer preparation designs are sparse. PURPOSE: The purpose of this 3-dimensional (3D) finite element analysis with microcomputed tomography (µCT) data obtained from realistic models was to assess the influence of different preparations for ceramic and composite resin veneers on restoration and resin layer stress distribution. MATERIAL AND METHODS: Four replicas of a central incisor were printed and prepared for laminate veneers with 4 different incisal edge designs: shoulder (SH), palatal chamfer (PC), palatal chamfer and oblique fracture involving the distal angle (OF-PC), and palatal chamfer involving horizontal incisal fracture (IF-PC). After fabrication and cementation of the veneers, the restored replicas were assessed with µCT, and 3D finite element models were built. A 100-N load was applied on the palatal surface at 60 and 125 degrees relative to the longitudinal axis. Maximum principal stress and stress distribution on the veneers, cement layer, and tooth structure were calculated and analyzed. RESULTS: The SH preparation exhibited better stress distribution than the PC preparation, and the cement layer and the veneer were subjected to lower stress. The IF-PC preparation had better stress distribution than the OF-PC. The shoulder and IF-PC showed higher stress on laminate veneers, but lower stress on the cement layer. Ceramic veneers exhibited lower stress than composite resin veneers. CONCLUSIONS: The different incisal preparations for laminate veneers influenced stress distribution on restorations and on the resin cement layer. The shoulder type preparation showed better stress distribution and the composite resin veneers showed unfavorable results compared with the ceramic veneers.

Clinical outcomes of self-glazed zirconia veneers produced by 3D gel deposition: a retrospective study.

BACKGROUND: Self-glazed zirconia (SZ) restorations are made by a novel additive three-dimensional gel deposition approach, which are suitable for a straightforward completely digital workflow. SZ has recently been used as minimally invasive veneer, but its clinical outcomes have not been clarified yet. This study aimed to evaluate the preliminary clinical outcomes of SZ veneers compared with the widely used lithium disilicate glass-ceramic veneers made by either pressing (PG) or milling (MG) process. METHODS: Fifty-six patients treated with SZ, PG, and MG veneers by 2 specialists between June 2018 and October 2022 were identified. Patients were recalled for follow-up at least 1 year after restoration. Clinical outcomes were assessed by 2 independent evaluators according to the modified United States Public Health Service (USPHS) criteria. Overall patient satisfaction was assessed using visual analogue scale (VAS), and analyzed by one-way ANOVA. Chi-square test was applied to compare the difference in the success and survival rates among the 3 groups. RESULTS: A total of 51 patients restored with 45 SZ, 40 PG, and 41 MG veneers completed the study, with a patient dropout rate of 8.9%. Mean and standard deviation of follow-up period was 35.0 ± 14.7 months. All restorations performed well at baseline, except for 2 SZ veneers with mismatched color (rated Bravo). During follow-up, marginal discrepancy (rated Bravo) was found in 4 MG veneers and 1 PG veneer, and partially fractured (rated Charlie) was found in another 2 PG veneers. The survival rate of SZ, PG, and MG veneers was 100%, 95%, and 100%, with a success rate of 95.56%, 92.50%, and 90.24%, respectively, none of which were significantly different (p = 0.099 and 0.628, respectively). The mean VAS score of SZ, PG, and MG was 95.00 ± 1.57, 93.93 ± 2.40, and 94.89 ± 2.00 respectively, without significant difference (p > 0.05). CONCLUSION: SZ veneers exhibited comparable preliminary clinical outcomes to PG and MG veneers, which could be considered as a feasible option for minimally invasive restorative treatment.

Componeer as an aesthetic treatment option for anterior teeth: a case report.

INTRODUCTION: Structural abnormalities or anomalies in the anterior teeth, also known as the aesthetic zone, are an important problem for patients and a challenge for dentists. Structural abnormalities or tooth anomalies can change in color, shape, and function. Most dentists prefer minimally invasive aesthetic treatment. One of the aesthetic treatment options for anterior teeth is veneers. Veneer is a restoration that covers the labial part of the tooth with a thin layer of material to correct abnormalities in the color, shape, or function of the tooth. Veneer restoration can be done indirectly with porcelain material made in a laboratory and directly with composite material on the tooth surface or prefabricated which is available from the factory. Componeer is a prefabricated composite veneer that combines the aesthetic properties of ceramic veneers and the adhesive ability of composite veneers to the tooth structure. This case report describes the treatment of two central incisors that had been filled with composite and peg shapes on both lateral incisors using a componeer. CASE REPORT: A 32-year-old female patient came to the Dental Conservation Clinic at Dentistry Hospital, Padjadjaran University with the main complaint of her right and left upper front teeth and wanted to repair her old fillings and close the gap between her right and left upper front teeth and her canine teeth. Clinical examination showed that teeth 11 and 21 had been filled with composite which had changed color and had an inharmonious shape as well as a gap between the upper front teeth on the right and left sides and the right and left canine teeth. TREATMENT: The maxilla and mandibular teeth are molded for study models and working models. In the working model, a wax-up is carried out, then a mock-up on the patient's teeth. Next, choose the color and size of the components that match the mock up results. Teeth 11 and 21 had their old composite fillings cleaned and refilled with dentin colored composite, teeth 13, 12, 11, 21, 22, and 23 were prepared with a minimum thickness of 0.3 mm to make room for the componeer material. The teeth was etched and bonded, and bonding was applied to the inner surface of the componeer. The composite is placed on the inner surface of the componeer then placed on the labial surface of the tooth and pressed with a special tool, then light cured. The final step is polishing. TREATMENT RESULTS: Teeth 13, 12, 11, 21, 22, and 23 which had undergone veneer treatment using componeer, were controlled after 1 week of treatment. The patient did not complain about the results of the treatment and said he was satisfied with the treatment.

Laser debonding of ultrathin occlusal veneers fabricated from different CAD/CAM ceramic materials.

BACKGROUND: Erbium lasers safely offer the possibility of reuse for debonded restorations. Since these lasers have a high affinity for water molecules, they are absorbed by resin cement causing explosive ablation of the cement and thus, the restoration debonds. The efficiency of this process depends on many factors, including the ceramic type, its chemical composition and thickness. Therefore, this study was designed to test the time taken to debond ultrathin occlusal veneers made of three types of milled ceramic materials and evaluate the integrity of these restorations after debonding. METHODS: Three ceramic types were evaluated in this study: lithium disilicate (IPS Emax CAD), highly condensed lithium disilicate (GC initial®LiSi), and translucent zirconia (Katana zirconia STML). Each group consisted of 8 occlusal veneers of 0.5 mm thickness. The samples were cemented to the occlusal surfaces of the upper molar teeth. An Er; Cr: YSGG laser was applied to the occlusal veneers using the scanning method, and time until debonding was calculated. The debonded samples were then inspected under a stereomicroscope for possible damage. Numerical data are presented as the mean with 95% confidence interval (CI), standard deviation (SD), minimum (min.) and maximum (max.) values. Normality and variance homogeneity assumptions were confirmed using Shapiro-Wilk's and Levene's tests, respectively. Data were normally distributed and were analyzed using one-way ANOVA followed by Tukey's post hoc test. The significance level was set at p < 0.05 for all tests. Statistical analysis was performed with R statistical analysis software version 4.3.2 for Windows (R Core Team (2023). R: A language and environment for statistical computing. R Foundation for Statistical Computing, Vienna, Austria. URL https://www.R-project.org/). RESULTS: There was no significant difference in debonding time between the different materials (p = 0.995). The longest debonding time was found for Katana STML (87.52 ± 20.45) (seconds), followed by Emax (86.94 ± 20.63) (seconds), while the lowest value was found for LiSi initial (86.14 ± 25.16) (seconds). In terms of damage to the debonded veneers, The Emax and zirconia samples showed no damage. However, 40% of the LiSi samples fractured during debonding, and 20% exhibited cracks. Only 40% of the LiSi samples were sound after debonding. CONCLUSION: Er; Cr: YSGG laser can be used efficiently to remove ceramic occlusal veneers. However, its effect on LiSi restorations needs further research.

Effect of surface treatment and resin cement type on the bond strength of polyetheretherketone to lithium disilicate ceramic.

BACKGROUND: This study aims to evaluate the effect of surface treatment and resin cement on the shear bond strength (SBS) and mode of failure of polyetheretherketone (PEEK) to lithium disilicate ceramic (LDC). This is suggested to study alternative veneering of PEEK frameworks with a ceramic material. METHODS: eighty discs were prepared from PEEK blank and from lithium disilicate ceramic. Samples were divided into four groups according to surface treatment: Group (A) air abraded with 110 µm Al2O3, Group (AP) air abrasion and primer application, Group (S) 98% sulfuric acid etching for 60 s, Group (SP) Sulfuric acid and primer. Each group was subdivided into two subgroups based on resin cement type used for bonding LDC:1) subgroup (L) self- adhesive resin cement and 2) subgroup (B) conventional resin cement (n = 10). Thermocycling was done for all samples. The bond strength was assessed using the shear bond strength test (SBS). Failure mode analysis was done at 50X magnification with a stereomicroscope. Samples were chosen from each group for scanning electron microscope (SEM). The three-way nested ANOVA followed by Tukey's post hoc test were used for statistical analysis of results. Comparisons of effects were done utilizing one way ANOVA and (p < 0.05). RESULTS: The highest mean of shear bond strength values was demonstrated in Group of air abrasion with primer application using conventional resin cement (APB) (12.21 ± 2.14 MPa). Sulfuric acid groups showed lower shear bond strength values and the majority failed in thermocycling especially when no primer was applied. The failure mode analysis showed that the predominant failure type was adhesive failure between cement and PEEK, while the remaining was mixed failure between cement and PEEK. CONCLUSION: The air abrasion followed by primer application and conventional resin cement used for bonding Lithium Disilicate to PEEK achieved the best bond strength. Primer application did not have an effect when self-adhesive resin cement was used in air-abraded groups. Priming step is mandatory whenever sulfuric acid etching surface treatment is utilized for PEEK.

Tetracycline staining of the dentition: a review of the literature and report of a clinical case.

The present article reviews the literature regarding tetracycline staining of the dentition and its esthetic management. A total of 49 articles were identified in the initial search, and 22 articles met the eligibility criteria of this narrative literature review. Tetracycline staining results from its use in children between the ages of 6 months and 6 years, when tooth crowns are formed; the effects are dependent on the dosage, duration of treatment, stage of tooth mineralization, and activity of the mineralization process. Tooth bleaching is always the first treatment option for low-grade cases of tetracycline staining. Restorative procedures are indicated for severe staining. The article also describes the treatment of severe staining affecting the maxillary anterior dentition of a 48-year-old man who reported the systemic administration of tetracycline during childhood. Direct composite resin laminate veneers were proposed to achieve immediate, highly esthetic restorations. A combination of different resinous materials in different shades was applied to meet the needs of the patient. The use of direct composite resin laminate veneers satisfied the functional and esthetic demands of the patient at a lower cost than ceramic materials.

[Study on the pressure on ceramic veneers during cementation]. / Izuchenie velichiny davleniya na keramicheskie viniry vo vremya ikh tsementirovaniya.

OBJECTIVE: The aim of the study is measuring the magnitude and determining the method of finger pressure exerted by doctors on ceramic veneers during their fixation. MATERIAL AND METHODS: A simulation model was designed in order to measure the volume of finger pressure. Veneers were produced for 2 central incisors. Doctors alternately placed veneers on the model and applied pressure on them for 20 seconds simulating the clinical stage of cementing. The operator recorded the maximum readings of the scales and entered the result on the research protocol. In addition, it was recorded which finger the doctor exerts on the veneer during its cementing to ensure a tight fit: thumb or index finger. RESULTS: The values obtained during cementation of 54% doctors ranged up to 1 kg, 27% of doctors from 1 to 2 kg and only 19% more than 2 kg. 80% of doctors applied the main pressure on the veneer using their thumb, while the pressure force was 1.4 kg. For those doctors who pressed the veneer to the tooth with their index finger, the impact value was 0.8 kg. CONCLUSION: The finger pressure on the veneer during cementation applied by dentists varies, the average pressure on the veneers was about 1.5 kg. The amount of pressure on cement during laboratory tests of cements for fixing veneers differs from clinical values many times. The development of a veneers fixation protocol, taking into account the conducted research, will ensure a reliable and accurate fit of the veneer at the stage of its cementing.

Four-point flexural strength and microtensile bond strength of digitally and conventionally veneered zirconia.

This study intended to evaluate the effect of digital veneering on four-point flexural strength (FS) and microtensile bond strength (µTBS) of veneered zirconia. Two different zirconia blocks, a lithium disilicate and a feldspathic ceramic block, and two different layering ceramics were used. IPS e.max Zir CAD (ZC) and Vita In-Ceram YZ (YZ) with yttria stabilized tetragonal zirconia polycrystals (3Y-TZP) were used as substructures. IPS e.max CAD (LD), Vita Mark II (VMII), IPS e.max Ceram (EC) and Vita VM9 (VM9) were used for veneering. Resin cement and fusion ceramic were placed between veneer and zirconia substructure for digital veneering. A total of one hundred and fifty specimens in five groups (n = 30) were prepared for FS and tested in universal machine at 1.0 mm/min. One hundred specimens in five groups (n = 20) were obtained for the µTBS and tested at 1.0 mm/min. Statistical analysis was made by one way ANOVA and Tukey HSD. Conventional veneering showed statistically significant FS. ZC veneered with EC had the highest mean FS and the lowest was obtained in groups veneered through resin cement. YZ layered with VM9 had the highest mean µTBS. ZC veneered through fusion ceramic and YZ veneered through resin cement showed significantly lower and similar µTBS.

Effect of veneering material type and thickness ratio on flexural strength of bi-layered PEEK restorations before and after thermal cycling.

OBJECTIVE: The purpose of this study was evaluating the biaxial strength of bi-layered PEEK restorations before and after aging using different veneering materials in different thickness ratios. MATERIAL AND METHODS: Ninety specimens of thickness 1.5 mm were divided into three groups according to their veneering material. Group (CAD LD): BioHPP discs veneered with CAD milled lithium disilicate (n=30), group (CAD C): BioHPP discs veneered with CAD milled composite (n=30), and group (LC): BioHPP discs veneered with conventionally layered composite (n=30). Each group was subdivided into 3 subgroups (n=10) according to the different thickness ratios between the core and the veneering material (TC:TV). Subgroup 1: TC:TV=1:0.5, subgroup 2: TC:TV=0.7:0.8, and subgroup 3: TC:TV=0.5:1. Half of the specimens of each subgroup were subjected to thermocycling, and the bi-axial flexural strength of all specimens was tested before and after aging. Three-way ANOVA followed by Bonferroni's post hoc test were used for data analysis. The significance level was set at P ≤ 0.05. RESULTS: Material, thickness ratio, and aging all had a significant effect on biaxial flexural strength. (LC) group had the highest biaxial flexural strength. TC:TV=0.5:1 showed the lowest biaxial flexural strength. All groups showed significant decrease in biaxial flexural strength after aging. CONCLUSIONS: Veneering material for PEEK together with the thickness ratio between the core and veneering material greatly affect the flexural strength of bi-layered restorations. Thermocycling negatively impacts the flexural strength of PEEK bi-layered restorations. CLINICAL SIGNIFICANCE: According to the results of that study, PEEK cores are best veneered with conventionally layered composite with core to veneering thickness ratio being 1:0.5.