A simple and precise methodology to determine particulate matter mass in atmospheric filters; validation and application cases.

In the past decades, particulate matter (PM) measurements have been used extensively in atmospheric sciences, as it allows studying the evolution of tracers for different atmospheric processes and the effects of atmospheric pollution on human health. However, measuring PM mass requires a constant control of the laboratory conditions due to its capacity to absorb humidity. For this reason, this study was focused on developing a novel, simple and precise methodology to determine the corrections of the filter mass due to humidity changes. The control and corrections are possible using a "control filter", which is always adapted to the environmental conditions of the laboratory. To check the consistency of this method, it was proved that the mass of any problem filter and that of the control filter behave in a very similar way. This allows quantifying the mass changes of any problem filter by using the control filter, where the problem filters and the control filter must have the same chemical composition and dimensions. To validate this methodology, a comparison was made between the methodology proposed in this study (Method-1) and the one proposed by the EPA (Method-2), which is generally applied. The particulate matter mass (m) was obtained for a problem filter for different weights, achieving similar values using both methods. However, Method-1 still provided reliable mass measurements for relative humidities very different from 50%, even as low as 18%. It was also proved that the adsorption or loss of water by the particulate matter can be neglected, since m is much smaller than the blank filter mass. Method-1 was also employed in several samplings carried out using three PM10 samplers to determine contaminants, such as 7Be and 210Pb, obtaining a good agreement between all particulate masses and activities measured by the three samplers for all samplings.

Valorisation of waste ilmenite mud in the manufacture of sulphur polymer cement.

This paper reports the preparation of sulphur polymer cements (SPCs) incorporating waste ilmenite mud for use in concrete construction works. The ilmenite mud raw material and the mud-containing SPCs (IMC-SPCs) were characterised physico-chemically and radiologically. The optimal IMC-SPC mixture had a sulphur/mud ratio (w/w) of 1.05 (mud dose 20 wt%); this cement showed the greatest compressive strength (64 MPa) and the lowest water absorption coefficient (0.4 g cm(-2) at 28 days). Since ilmenite mud is enriched in natural radionuclides, such as radium isotopes (2.0·10(3) Bq kg(-1)(228)Ra and 5.0·10(2) Bq kg(-1)(226)Ra), the IMC-SPCs were subjected to leaching experiments, which showed their environmental impact to be negligible. The activity concentration indices for the different radionuclides in the IMC-SPCs containing 10% and 20% ilmenite mud met the demands of international standards for materials used in the construction of non-residential buildings.

A new methodology based on TRU resin to measure U-, Th-isotopes and 210Po by alpha-particle spectrometry.

This report presents a new methodology to isolate and measure 210Po, as well as uranium and thorium isotopes. This new methodology reduces the standard time of operation, the minimum amount of chemical reagents and the quantity of resin used in comparison with other standard and well-established procedures for alpha spectrometry. Thus, the amount of chemicals reagent was lower than the amount used in other standard radiochemical processes: only 6 mL of 1 M HCl was used for the thorium elution, and 2 mL of H2O and 1 mL of Ammonium Oxalate (0.05 M) (3 mL in total) for the uranium elution. Likewise, many samples of various activities and materials (liquids and solids) were used to validate the method.

Metabarcoding data of prokaryotes and eukaryotes inhabiting the phosphogypsum stockpiles on the salt marshes of Huelva (SW Spain).

Around 100 Mt of phosphogypsum (PG) of extreme acidity and with high concentrations of heavy metals and radionuclides have been deposited on the salt marshes of the Tinto River estuary in Huelva (SW Spain) for more than forty years. The microbial community able to thrive in these adverse conditions remains totally unknown, despite the fact that it can highly influence the biogeochemical cycle of the phosphogypsum components and include new species with biotechnological interest. High throughput sequencing of 16S/18S rRNA encoding genes is a potent tool to uncover the microbial diversity of extreme environments. This data article describes for the first time the prokaryotic and eukaryotic diversity of two water samples collected in the Huelva phosphogypsum stacks. The raw amplicons of the 16S/18S rRNA maker genes for the two phosphogypsum samples and two reference samples (seawater and the Tinto River water) obtained after sequencing on MiSeq platform are provided. The operational taxonomic units (OTUs) obtained after the treatment and clustering of the obtained reads with the QIIME2 pipeline and their taxonomic assignation performed by comparison with the SILVA database are also presented to complete the information of the article "Exploring the microbial community inhabiting the phosphogypsum stacks of Huelva (SW, Spain) by a high throughput 16S/18S rDNA Sequencing approach".

Exploring the microbial community inhabiting the phosphogypsum stacks of Huelva (SW SPAIN) by a high throughput 16S/18S rDNA sequencing approach.

Around 100 Mt of phosphogypsum (PG) have been deposited in large stacks on the salt marshes of the Tinto River estuary in Huelva (SW Spain), covering about 1000 ha. These stacks contain extremely acidic water (pH < 2) with high concentrations of pollutants which can cause emissions into their surroundings, generating important environmental concerns. Despite many chemical, geological or hydrological studies have been conducted to characterize the PG stacks of Huelva, the microbial community inhabiting this extreme environment remains unexplored. Using a 16S/18S-rRNA-high throughput sequencing approach, we have uncovered the main taxonomic groups able to live in the acidic metal-contaminated water, which is in direct contact with the PG, demonstrating for the first time the existence of a huge diversity of microbial species in these extreme conditions. In addition, the physicochemical characteristics of the water sampled have been analyzed. These studies have revealed that the most abundant bacteria found in two different leachate samples of the PG stacks belong to the genera Acidiphilium, Pseudomonas, Leptosprillum, Acidithrix, or Acidithiobacillus, typically found in acid mine drainage (AMD) environments, which in total represent around 50% of the total bacterial community. Biodiversity of eukaryotes in PG water is lower than that of prokaryotes, especially in the water collected from the perimeter channel that surrounds the PG stacks, where the pH reaches a value of 1.5 and the activity concentrations exceed 300 Bq L-1 for 238U or 20 Bq L-1 for 210Po, values which are from four to five orders of magnitude higher than those usually found in unperturbed surface waters. Even so, an unexpected diversity of algae, fungi, and ciliates have been found in the PG stacks of Huelva, where chlorophyte microalgae and basidiomycetes fungi are the most abundant eukaryotes. Additional bioinformatics tools have been used to perform a functional analysis and predict the most common metabolic pathways in the PG microbiota. The obtained data indicate that the extreme conditions of these PG stacks hide an unexpected microbial diversity, which can play an important role in the dynamics of the contaminating compounds of the PG and provide new strains with unique biotechnological applications.

Synoptic and meteorological characterisation of olive pollen transport in Córdoba province (south-western Spain).

The main goal of the present study was to provide a detailed analysis of olive pollen transport dynamics in the province of Córdoba (south-western Spain) by applying back-trajectory analysis. Pollen data from 2006 and 2007 were analysed at four monitoring sites: Córdoba city in the centre of the province, Baena and Priego de Córdoba located in the south, and El Cabril reserve (Hornachuelos Natural Park) in the north. Particular attention was paid to nine episodes of high pollen counts. Synoptic surface maps were used, and kinematic back-trajectories (3D) were computed using the hybrid single particle Lagrangian integrated trajectory model (HYSPLIT) at 500 m above ground level, run with a time-step of 6 h over a period of 36 h. Findings were analysed in conjunction with daily and bi-hourly airborne pollen data, field phenological data and hourly surface meteorological data recorded at nearby stations: temperature, relative humidity, rainfall, wind direction and wind speed. The results identified two pollen source areas over the Córdoba province, the largest one located in the south, affecting Baena, Priego de Córdoba and Córdoba city, and one smaller located in the west, which determines mainly the pollen cycle over the north of the province, El Cabril. In addition, two air mass circulations were found, one coming from the south and crossing the main olive pollen sources very close to the surface and being frequently associated with higher pollen counts, and the other coming from the west and, in the episodes investigated, influencing mainly the north of the province.

Recycled Aggregates from Construction and Demolition Waste in the Manufacture of Urban Pavements.

Construction and Demolition Waste (CDW) is among the largest waste streams in the world. Therefore, within the Circular Economy concept, there is a growing interest in its reuse. The purpose of this work was to study the use of recycled aggregates (RAs) obtained by a specific separation method from CDW, replacing natural aggregates (NAs) in the manufacture of precast concrete elements, such as kerbstones and paver blocks. The physical and technological properties of precast products formulated with RAs were analysed in accordance with current regulations, comparing them with those of commercial products manufactured with NAs. The results indicated that partial or total substitution of NAs by RAs increased the water absorption and apparent porosity values of the precast elements while reducing the bulk density and compressive strength. However, all units manufactured with RAs showed breaking load values higher than the minimum required by EN 1338 and, in some cases, slightly higher average tensile strength values than the reference material. In addition, some of the compositions including RAs gave rise to pieces that, according to their flexural strength, were classified as class 1 and marked S in accordance with EN 1340. According to abrasion resistance, in most cases, the precast elements are classified as Class 4 and I (≤20 mm). Finally, precast concrete produced from RAs satisfies the tolerance requirements for classification as class 3 (≤1.5 kg m-2). Therefore, it could be suitable for use in high pedestrian or traffic areas.

Evaluation of the radioactive pollution in the salt-marshes under a phosphogypsum stack system.

Next to the city of Huelva (SW of Spain), around 100 Mt of phosphogypsum (PG) are stored in stacks on the salt-marshes of the Tinto River estuary covering a surface of about 1000 ha. Due to the high content of 238U series natural radionuclides of the PG, its acidic nature (pH about 3), and the fact that PG stacks were disposed without any kind of isolation from the substrate, they could produce a potential radioactive impact into the underlying sediments. The aim of this work is to assess the pollution of the underlying sediments by natural radionuclides coming from the PG stacks. To this end, seven cores were taken, and PG and sediments samples collected at different depths were analysed. The activity concentrations of the main long half-live natural radionuclides of interest were determined by applying both gamma-ray and alpha-particle spectrometry radiometric techniques. The results of this study showed that the first decimeters of salt-marsh sediment act as a "barrier" for the radionuclides coming from the PG stacks decreasing rapidly its activity concentration in depth, affecting mainly sediments located in the first 20 cm below the contact due to mixing processes. While 230Th, 226Ra and 210Pb pollution is mainly restricted to the first 20 cm of sediments, U-isotopes can reach higher depths (up to around 50 cm) by leaching processes due to their lower reactivity and higher concentration in the polluted leachates. The obtained results have high relevance for the design of the perimeter channel which is projected to build in the restoration project, suggesting that should has around 1 m deep under the base of the PG stacks, to ensure the full collection of polluting leachates, and to prevent their release into the estuary of the Tinto River.

Pollution evaluation on the salt-marshes under the phosphogypsum stacks of Huelva due to deep leachates.

In the salth-marshes of the Tinto River (Huelva estuary, SW Spain), are stored in stacks around 100 Mt of PG, covering a surface of 1000 ha without any type of isolation, which produce an important impact in the surrounding environment. On the other hand, this ecosystem it is affected by acid mine drainage (AMD) from sulphide mines located upstream the Tinto River. The aim of this study is to evaluate the deep pollution of the underlain salt-marsh sediments due to leachates from the PG stacks. For that purpose, 7 cores were collected from zones 2 and 3 of the stacks, and PG and salt-marsh sediments samples from different depths were analyzed. The physicochemical parameters, mineralogy, granulometry and the concentration of the main elements of interest were determined in the samples. Most analysed salt-marsh sediments are not affected by PG stacks pollution, because sediments act as a "barrier" for the leachates from the PG, concentrating the contaminants in the first decimetres (0.5 m) under PG-sediments contact, and the deep infiltration is very limited. The obtained results suggest that the perimeter channel which is projected to build in the restauration project, should has a depth of 1 m below the level of the PG stacks for assuring the complete collection of leachates from the stacks, and avoid their liberation into the Tinto River estuary.

U-isotopes and (226)Ra as tracers of hydrogeochemical processes in carbonated karst aquifers from arid areas.

Sierra de Gádor is a karst macrosystem with a highly complex geometry, located in southeastern Spain. In this arid environment, the main economic activities, agriculture and tourism, are supported by water resources from the Sierra de Gádor aquifer system. The aim of this work was to study the levels and behaviour of some of the most significant natural radionuclides in order to improve the knowledge of the hydrogeochemical processes involved in this groundwater system. For this study, 28 groundwater and 7 surface water samples were collected, and the activity concentrations of the natural U-isotopes ((238)U, (235)U and (234)U) and (226)Ra by alpha spectrometry were determined. The activity concentration of (238)U presented a large variation from around 1.1 to 65 mBq L(-1). Elevated groundwater U concentrations were the result of oxidising conditions that likely promoted U dissolution. The PHREEQC modelling code showed that dissolved U mainly existed as uranyl carbonate complexes. The (234)U/(238)U activity ratios were higher than unity for all samples (1.1-3.8). Additionally, these ratios were in greater disequilibrium in groundwater than surface water samples, the likely result of greater water-rock contact time. (226)Ra presented a wide range of activity concentrations, (0.8 up to about 4 × 10(2) mBq L(-1)); greatest concentrations were detected in the thermal area of Alhama. Most of the samples showed (226)Ra/(234)U activity ratios lower than unity (median = 0.3), likely the result of the greater mobility of U than Ra in the aquifer system. The natural U-isotopes concentrations were strongly correlated with dissolution of sulphate evaporites (mainly gypsum). (226)Ra had a more complex behaviour, showing a strong correlation with water salinity, which was particularly evident in locations where thermal anomalies were detected. The most saline samples showed the lowest (234)U/(238)U activity ratios, probably due to fast uniform bulk mineral dissolution, which would minimize the impact of solubility-controlled fractionation processes. Furthermore, the high bulk dissolution rates promoted greater groundwater (226)Ra/(234)U ratios because the Ra has a comparatively much greater mobility than U in saline conditions.

Radioactive impact in sediments from an estuarine system affected by industrial wastes releases.

A big fertilizer industrial complex and a vast extension of phosphogypsum piles (12 km2), sited in the estuary formed by the Odiel and Tinto river mouths (southwest of Spain), are producing an unambiguous radioactive impact in their surrounding aquatic environment through radionuclides from the U-series. The levels and distribution of radionuclides in sediments from this estuarine system have been determined. The analyses of radionuclide concentrations and activity ratios have provided us with an interesting information to evaluate the extension, degree and routes of the radioactive impact, as well as for the knowledge of the different pathways followed for the radioactive contamination to disturb this natural system. The obtained results indicate that the main pathway of radioactive contamination of the estuary is through the dissolution in its waters of the radionuclides released by the industrial activities and their later fixation on the particulate materials. Tidal activity also plays an important role in the transport and homogenization along the estuary of the radioactivity released from the fertilizer plants.

Microencapsulation of phosphogypsum into a sulfur polymer matrix: physico-chemical and radiological characterization.

The aim of this work is to prepare a new type of phosphogypsum-sulfur polymer cements (PG-SPC) to be utilised in the manufacture of building materials. Physico-chemical and radiological characterization was performed in phosphogypsum and phosphogypsum-sulfur polymer concretes and modeling of exhalation rates has been also carried out. An optimized mixture of the materials was obtained, the solidified material with optimal mixture (sulfur/phosphogypsum=1:0.9, phosphogypsum dosage=10-40 wt.%) results in highest strength (54-62 MPa) and low total porosity (2.8-6.8%). The activity concentration index (I) in the PG-SPC is lower than the reference value in the most international regulations and; therefore, these cements can be used without radiological restrictions in the manufacture of building materials. Under normal conditions of ventilation, the contribution to the expected radon indoor concentration in a standard room is below the international recommendations, so the building materials studied in this work can be applied to houses built up under normal ventilation conditions. Additionally, and taking into account that the PG is enriched in several natural radionuclides as (226)Ra, the leaching experiments have demonstrated that environmental impact of the using of SPCs cements with PG is negligible.