Chiral Symmetry Breaking for Deterministic Switching of Perpendicular Magnetization by Spin-Orbit Torque.

Symmetry breaking is a characteristic to determine which branch of a bifurcation system follows upon crossing a critical point. Specifically, in spin-orbit torque (SOT) devices, a fundamental question arises: how can the symmetry of the perpendicular magnetic moment be broken by the in-plane spin polarization? Here, we show that the chiral symmetry breaking by the antisymmetric Dzyaloshinskii-Moriya interaction (DMI) can induce the deterministic SOT switching of the perpendicular magnetization. By introducing a gradient of saturation magnetization or magnetic anisotropy, the dynamic noncollinear spin textures are formed under the current-driven SOT, and thus, the chiral symmetry of these dynamic spin textures is broken by the DMI, resulting in the deterministic magnetization switching. We introduce a strategy to induce an out-of-plane (z) gradient of magnetic properties as a practical solution for the wafer-scale manufacture of SOT devices.

Influence of Nonuniform Micron-Scale Strain Distributions on the Electrical Reorientation of Magnetic Microstructures in a Composite Multiferroic Heterostructure.

Composite multiferroic systems, consisting of a piezoelectric substrate coupled with a ferromagnetic thin film, are of great interest from a technological point of view because they offer a path toward the development of ultralow power magnetoelectric devices. The key aspect of those systems is the possibility to control magnetization via an electric field, relying on the magneto-elastic coupling at the interface between the piezoelectric and the ferromagnetic components. Accordingly, a direct measurement of both the electrically induced magnetic behavior and of the piezo-strain driving such behavior is crucial for better understanding and further developing these materials systems. In this work, we measure and characterize the micron-scale strain and magnetic response, as a function of an applied electric field, in a composite multiferroic system composed of 1 and 2 µm squares of Ni fabricated on a prepoled [Pb(Mg1/3Nb2/3)O3]0.69-[PbTiO3]0.31 (PMN-PT) single crystal substrate by X-ray microdiffraction and X-ray photoemission electron microscopy, respectively. These two complementary measurements of the same area on the sample indicate the presence of a nonuniform strain which strongly influences the reorientation of the magnetic state within identical Ni microstructures along the surface of the sample. Micromagnetic simulations confirm these experimental observations. This study emphasizes the critical importance of surface and interface engineering on the micron-scale in composite multiferroic structures and introduces a robust method to characterize future devices on these length scales.

Proliferation of human aortic endothelial cells on Nitinol thin films with varying hole sizes.

In this paper, we present the effect of micron size holes on proliferation and growth of human aortic endothelial cells (HAECs). Square shaped micron size holes (5, 10, 15, 20 and 25 µm) separated by 10 µm wide struts are fabricated on 5 µm thick sputter deposited Nitinol films. HAECs are seeded onto these micropatterned films and analyzed after 30 days with fluorescence microscopy. Captured images are used to quantify the nucleus packing density, size, and aspect ratio. The films with holes ranging from 10 to 20 µm produce the highest cell packing densities with cell nucleus contained within the hole. This produces a geometrically regular grid like cellular distribution pattern. The cell nucleus aspect ratio on the 10-20 µm holes is more circular in shape when compared to aspect ratio on the continuous film or larger size holes. Finally, the 25 µm size holes prevented the formation of a continuous cell monolayer, suggesting the critical length that cells cannot bridge is between 20 to 25 µm.

Nanoscale magnetic ratchets based on shape anisotropy.

Controlling magnetization using piezoelectric strain through the magnetoelectric effect offers several orders of magnitude reduction in energy consumption for spintronic applications. However strain is a uniaxial effect and, unlike directional magnetic field or spin-polarized current, cannot induce a full 180° reorientation of the magnetization vector when acting alone. We have engineered novel 'peanut' and 'cat-eye' shaped nanomagnets on piezoelectric substrates that undergo repeated deterministic 180° magnetization rotations in response to individual electric-field-induced strain pulses by breaking the uniaxial symmetry using shape anisotropy. This behavior can be likened to a magnetic ratchet, advancing magnetization clockwise with each piezostrain trigger. The results were validated using micromagnetics implemented in a multiphysics finite elements code to simulate the engineered spatial and temporal magnetic behavior. The engineering principles start from a target device function and proceed to the identification of shapes that produce the desired function. This approach opens a broad design space for next generation magnetoelectric spintronic devices.

Fast Magnetic Domain-Wall Motion in a Ring-Shaped Nanowire Driven by a Voltage.

Magnetic domain-wall motion driven by a voltage dissipates much less heat than by a current, but none of the existing reports have achieved speeds exceeding 100 m/s. Here phase-field and finite-element simulations were combined to study the dynamics of strain-mediated voltage-driven magnetic domain-wall motion in curved nanowires. Using a ring-shaped, rough-edged magnetic nanowire on top of a piezoelectric disk, we demonstrate a fast voltage-driven magnetic domain-wall motion with average velocity up to 550 m/s, which is comparable to current-driven wall velocity. An analytical theory is derived to describe the strain dependence of average magnetic domain-wall velocity. Moreover, one 180° domain-wall cycle around the ring dissipates an ultrasmall amount of heat, as small as 0.2 fJ, approximately 3 orders of magnitude smaller than those in current-driven cases. These findings suggest a new route toward developing high-speed, low-power-dissipation domain-wall spintronics.

Modeling of magnetoelastic nanostructures with a fully coupled mechanical-micromagnetic model.

Micromagnetic simulations of magnetoelastic nanostructures traditionally rely on either the Stoner-Wohlfarth model or the Landau-Lifshitz-Gilbert (LLG) model, assuming uniform strain (and/or assuming uniform magnetization). While the uniform strain assumption is reasonable when modeling magnetoelastic thin films, this constant strain approach becomes increasingly inaccurate for smaller in-plane nanoscale structures. This paper presents analytical work intended to significantly improve the simulation of finite structures by fully coupling the LLG model with elastodynamics, i.e., the partial differential equations are intrinsically coupled. The coupled equations developed in this manuscript, along with the Stoner-Wohlfarth model and the LLG (constant strain) model are compared to experimental data on nickel nanostructures. The nickel nanostructures are 100 × 300 × 35 nm single domain elements that are fabricated on a Si/SiO2 substrate; these nanostructures are mechanically strained when they experience an applied magnetic field, which is used to generate M vs H curves. Results reveal that this paper's fully-coupled approach corresponds the best with the experimental data on coercive field changes. This more sophisticated modeling technique is critical for guiding the design process of future nanoscale strain-mediated multiferroic elements, such as those needed in memory systems.

In vitro evaluation of an external compression device for fontan mechanical assistance.

While Fontan palliation in the form of the total cavopulmonary connection has improved the management of congenital single ventricle physiology, long-term outcomes for patients with this disease are suboptimal due to the lack of two functional ventricles. Researchers have shown that ventricular assist devices (VADs) can normalize Fontan hemodynamics. To minimize blood contacting surfaces of the VAD, we evaluated the use of an external compression device (C-Pulse Heart Assist System, Sunshine Heart Inc.) as a Fontan assist device. A mock circulation was developed to mimic the hemodynamics of a hypertensive Fontan circulation in a pediatric patient. The Sunshine C-Pulse compression cuff was coupled with polymeric valves and a compressible tube to provide nonblood-contacting pulsatile flow through the Fontan circulation. The effect of the number, one or two, and placement of valves, before or after the compression cuff, on inferior vena cava pressure (IVCP) was studied. In addition, the effect of device inflation volume and compression rate on maintaining low IVCP was investigated. With one valve located before the cuff, the device was unable to maintain an IVCP below 15.5 mm Hg. With two valves, the C-Pulse was able to maintain IVCP as low as 8.5 mm Hg. The C-Pulse provided pulsatile flow and pressure through the pulmonary branch of the mock circulation with a pulse pressure of 16 mm Hg and 180 mL/min additional flow above unassisted flow. C-Pulse compression reduced IVCP below 12 mm Hg with 13 cc inflation volume and compression rates above 105 bpm. This application of an external compression device combined with two valves has potential for use as an artificial right ventricle by maintaining low IVCP and providing pulsatile flow through the lungs.

Magnetoelectric control of superparamagnetism.

Here we demonstrate electric-field induced magnetic anisotropy in a multiferroic composite containing nickel nanocrystals strain coupled to a piezoelectric substrate. This system can be switched between a superparamagnetic state and a single-domain ferromagnetic state at room temperature. The nanocrystals show a shift in the blocking temperature of 40 K upon electric poling. We believe this is the first example of a system where an electric field can be used to switch on and off a permanent magnetic moment.

3D Printing and processing of miniaturized transducers with near-pristine piezoelectric ceramics for localized cavitation.

The performance of ultrasonic transducers is largely determined by the piezoelectric properties and geometries of their active elements. Due to the brittle nature of piezoceramics, existing processing tools for piezoelectric elements only achieve simple geometries, including flat disks, cylinders, cubes and rings. While advances in additive manufacturing give rise to free-form fabrication of piezoceramics, the resultant transducers suffer from high porosity, weak piezoelectric responses, and limited geometrical flexibility. We introduce optimized piezoceramic printing and processing strategies to produce highly responsive piezoelectric microtransducers that operate at ultrasonic frequencies. The 3D printed dense piezoelectric elements achieve high piezoelectric coefficients and complex architectures. The resulting piezoelectric charge constant, d33, and coupling factor, kt, of the 3D printed piezoceramic reach 583 pC/N and 0.57, approaching the properties of pristine ceramics. The integrated printing of transducer packaging materials and 3D printed piezoceramics with microarchitectures create opportunities for miniaturized piezoelectric ultrasound transducers capable of acoustic focusing and localized cavitation within millimeter-sized channels, leading to miniaturized ultrasonic devices that enable a wide range of biomedical applications.

Super hydrophilic thin film nitinol demonstrates reduced platelet adhesion compared with commercially available endograft materials.

BACKGROUND: Thin film nitinol (TFN) is a novel material with which to cover stents for the treatment of a wide range of vascular disease processes. This study aimed to show that TFN, if treated to produce a super hydrophilic surface, significantly reduces platelet adhesion, potentially rendering covered stents more resistant to thrombosis compared to commercially available materials. MATERIALS AND METHODS: TFN was fabricated using a sputter deposition process to produce a 5-µ thin film of uniform thickness. TFN then underwent a surface treatment process to create a super hydrophilic layer. Platelet adhesion studies compared surface treated TFN (S-TFN) to untreated TFN, polytetrafluoroethylene, Dacron, and bulk nitinol. In vivo swine studies examined the placement of an S-TFN covered stent in a 3.5 mm diameter external iliac artery. Angiography confirmed placement, and repeat angiography was performed at 2 wk followed by post mortem histopathology. RESULTS: S-TFN significantly reduced platelet adhesion without any evidence of aggregation compared with all materials studied (P < 0.05). Furthermore, in vivo swine studies demonstrated complete patency of the S-TFN covered stent at 2 wk. Post mortem histopathology showed rapid endothelialization of the S-TFN without excessive neointimal hyperplasia. CONCLUSIONS: These results demonstrate that S-TFN significantly reduces platelet adhesion and aggregation compared with commercially available endograft materials. Furthermore, the hydrophilic surface may confer thromboresistance in vivo, suggesting that S-TFN is a possible superior material for covering stents.

Single-Domain Multiferroic Array-Addressable Terfenol-D (SMArT) Micromagnets for Programmable Single-Cell Capture and Release.

Programming magnetic fields with microscale control can enable automation at the scale of single cells ≈10 µm. Most magnetic materials provide a consistent magnetic field over time but the direction or field strength at the microscale is not easily modulated. However, magnetostrictive materials, when coupled with ferroelectric material (i.e., strain-mediated multiferroics), can undergo magnetization reorientation due to voltage-induced strain, promising refined control of magnetization at the micrometer-scale. This work demonstrates the largest single-domain microstructures (20 µm) of Terfenol-D (Tb0.3 Dy0.7 Fe1.92 ), a material that has the highest magnetostrictive strain of any known soft magnetoelastic material. These Terfenol-D microstructures enable controlled localization of magnetic beads with sub-micrometer precision. Magnetically labeled cells are captured by the field gradients generated from the single-domain microstructures without an external magnetic field. The magnetic state on these microstructures is switched through voltage-induced strain, as a result of the strain-mediated converse magnetoelectric effect, to release individual cells using a multiferroic approach. These electronically addressable micromagnets pave the way for parallelized multiferroics-based single-cell sorting under digital control for biotechnology applications.

Magnetic memory driven by topological insulators.

Giant spin-orbit torque (SOT) from topological insulators (TIs) provides an energy efficient writing method for magnetic memory, which, however, is still premature for practical applications due to the challenge of the integration with magnetic tunnel junctions (MTJs). Here, we demonstrate a functional TI-MTJ device that could become the core element of the future energy-efficient spintronic devices, such as SOT-based magnetic random-access memory (SOT-MRAM). The state-of-the-art tunneling magnetoresistance (TMR) ratio of 102% and the ultralow switching current density of 1.2 × 105 A cm-2 have been simultaneously achieved in the TI-MTJ device at room temperature, laying down the foundation for TI-driven SOT-MRAM. The charge-spin conversion efficiency θSH in TIs is quantified by both the SOT-induced shift of the magnetic switching field (θSH = 1.59) and the SOT-induced ferromagnetic resonance (ST-FMR) (θSH = 1.02), which is one order of magnitude larger than that in conventional heavy metals. These results inspire a revolution of SOT-MRAM from classical to quantum materials, with great potential to further reduce the energy consumption.

Quantification of intraocular surgery motions with an electromagnetic tracking system.

Motion tracking was performed during a combined phacoemulsification (PKE) and pars plana vitrectomy (PPV) procedure on a pig eyeball. The UCLA Laparoscopic Training System (UCLA-LTS), which consists of electromagnetic sensors attached to the surgical tools to measure three-dimensional spatial vectors, was modified to enable quantification of intraocular surgery motions. The range of motion and time taken to complete the given task were successfully recorded.

Capturing magnetic bead-based arrays using perpendicular magnetic anisotropy.

Designing and implementing means of locally trapping magnetic beads and understanding the factors underlying the bead capture force are important steps toward advancing the capture-release process of magnetic particles for biological applications. In particular, capturing magnetically labeled cells using magnetic microstructures with perpendicular magnetic anisotropy (PMA) will enable an approach to cell manipulation for emerging lab-on-a-chip devices. Here, a Co (0.2 nm)/Ni (0.4 nm) multilayered structure was designed to exhibit strong PMA and large saturation magnetization (M s ). Finite element simulations were performed to assess the dependence of the capture force on the value of M s . The simulated force profile indicated the largest force at the perimeter of the disks. Arrays of Co/Ni disk structures of (4-7) µm diameter were fabricated and tested in a microchannel with suspended fluorescent magnetic beads. The magnetic beads were captured and localized to the edge of the disks as predicted by the simulations. This approach has been demonstrated to enable uniform assembly of magnetic beads without external fields and may provide a pathway toward precise cell manipulation methods.

Magnetoelectric Spin Wave Modulator Based On Synthetic Multiferroic Structure.

We describe a spin wave modulator - spintronic device aimed to control spin wave propagation by an electric field. The modulator consists of a ferromagnetic film serving as a spin wave bus combined with a synthetic multiferroic comprising piezoelectric and magnetostrictive materials. Its operation is based on the stress-mediated coupling between the piezoelectric and magnetostrictive materials. By applying an electric field to the piezoelectric layer, the stress is produced. In turn, the stress changes the direction of the easy axis in the magnetostrictive layer and affects spin wave transport. We present experimental data on a prototype consisting of a piezoelectric [Pb(Mg1/3Nb2/3)O3](1-x) -[PbTiO3]x substrate, and 30 nm layer of magnetostrictive Ni film, where the film is attached to a 30 nm thick Ni81Fe19 spin wave bus. We report spin wave signal modulation in Ni81Fe19 layer by an electric field applied across the piezoelectric layer. The switching between the spin wave conducting and non-conducting states is achieved by applying ±0.3 MV/m electric field. We report over 300% modulation depth detected 80 µm away from the excitation port at room temperature. The demonstration of the spin wave modulator provides a new direction for spin-based device development by utilizing an electric field for spin current control.

Large Interfacial Magnetostriction in (Co/Ni)4/Pb(Mg1/3Nb2/3)O3-PbTiO3 Multiferroic Heterostructures.

The magnetoelastic behavior of multiferroic heterostructures-coupling of magnetic anisotropy or domain dynamics to structural deformations-has been intensively studied for developing materials for energy-efficient, spin-based applications. Here, we report on a large, interface-dominated magnetostriction in (Co/Ni)4/Pb(Mg1/3Nb2/3)O3-PbTiO3 multiferroic heterostructures. Ferromagnetic resonance spectroscopy under voltage-induced strains enabled estimation of the saturation magnetostriction as a function of Ni thickness. The volume and the interface components to the saturation magnetostriction are (6.6 ± 0.9) × 10-6 and (-2.2 ± 0.2) × 10-14 m, respectively. Similar to perpendicular magnetic anisotropy in Co/Ni, the large, negative magnetostriction originates from the Co/Ni interfaces. This interfacial functionality delivers an effect over 300% larger than the bulk contribution and can enable low-energy, nanoelectronic devices that combine the tunable magnetic and magnetostrictive properties of Co/Ni multilayers with the ferroelectric properties of Pb(Mg1/3Nb2/3)O3-PbTiO3.

Bi-directional coupling in strain-mediated multiferroic heterostructures with magnetic domains and domain wall motion.

Strain-coupled multiferroic heterostructures provide a path to energy-efficient, voltage-controlled magnetic nanoscale devices, a region where current-based methods of magnetic control suffer from Ohmic dissipation. Growing interest in highly magnetoelastic materials, such as Terfenol-D, prompts a more accurate understanding of their magnetization behavior. To address this need, we simulate the strain-induced magnetization change with two modeling methods: the commonly used unidirectional model and the recently developed bidirectional model. Unidirectional models account for magnetoelastic effects only, while bidirectional models account for both magnetoelastic and magnetostrictive effects. We found unidirectional models are on par with bidirectional models when describing the magnetic behavior in weakly magnetoelastic materials (e.g., Nickel), but the two models deviate when highly magnetoelastic materials (e.g., Terfenol-D) are introduced. These results suggest that magnetostrictive feedback is critical for modeling highly magnetoelastic materials, as opposed to weaker magnetoelastic materials, where we observe only minor differences between the two methods' outputs. To our best knowledge, this work represents the first comparison of unidirectional and bidirectional modeling in composite multiferroic systems, demonstrating that back-coupling of magnetization to strain can inhibit formation and rotation of magnetic states, highlighting the need to revisit the assumption that unidirectional modeling always captures the necessary physics in strain-mediated multiferroics.

A pneumatic haptic feedback actuator array for robotic surgery or simulation.

Robot-assisted minimally invasive surgery (MIS) offers improved range of motion over standard laparoscopic techniques, but is characterized by a total loss of haptic feedback, requiring surgeons to rely solely on visual cues. Pneumatic tactile displays have many advantages, including low mass, low cost, compact size, and adaptability. A pneumatic haptic feedback actuator array has been developed that is suitable for mounting unto surgical robotic tools. The balloon actuators consist of spin-coated thin-film silicone membranes and molded substrates with cylindrical channels. Human perceptual tests were conducted on balloon diameters ranging from 0.75 to 2.0 mm to determine the optimal size that can be effectively detected. The control system was programmed to sequentially inflate a single balloon to one of the three levels, 100% (full hemispherical deformation), zero, 50% (half deformation), and 0% (no inflation). Blinded subjects (n=5) were asked to determine which of the two inflation levels was higher. Test results suggest that balloon diameters greater than 1.0 mm can deliver high detection accuracy. This indicates that pneumatic balloon-based actuation is a viable solution for generating haptic feedback. In addition to surgical applications, many other fields such as virtual reality-based simulators and neuroprosthetics can benefit from this technology.

An in vivo pilot study of a microporous thin film nitinol-covered stent to assess the effect of porosity and pore geometry on device interaction with the vessel wall.

Sputter-deposited thin film nitinol constructs with various micropatterns were fabricated to evaluate their effect on the vessel wall in vivo when used as a covering for commercially available stents. Thin film nitinol constructs were used to cover stents and deployed in non-diseased swine arteries. Swine were sacrificed after approximately four weeks and the thin film nitinol-covered stents were removed for histopathologic evaluation. Histopathology revealed differences in neointimal thickness that correlated with the thin film nitinol micropattern. Devices covered with thin film nitinol with a lateral × vertical length = 20 × 40 µm diamond pattern had minimal neointimal growth with well-organized cell architecture and little evidence of ongoing inflammation. Devices covered with thin film nitinol with smaller fenestrations exhibited a relatively thick neointimal layer with inflammation and larger fenestrations showed migration of inflammatory and smooth muscle cells through the micro fenestrations. This "proof-of-concept" study suggests that there may be an ideal thin film nitinol porosity and pore geometry to encourage endothelialization and incorporation of the device into the vessel wall. Future work will be needed to determine the optimal pore size and geometry to minimize neointimal proliferation and in-stent stenosis.