Development of a novel intravascular oxygenator catheter: Oxygen mass transfer properties across nonporous hollow fiber membranes.

Despite hypoxic respiratory failure representing a large portion of total hospitalizations and healthcare spending worldwide, therapeutic options beyond mechanical ventilation are limited. We demonstrate the technical feasibility of providing oxygen to a bulk medium, such as blood, via diffusion across nonporous hollow fiber membranes (HFMs) using hyperbaric oxygen. The oxygen transfer across Teflon® membranes was characterized at oxygen pressures up to 2 bars in both a stirred tank vessel (CSTR) and a tubular device mimicking intravenous application. Fluxes over 550 ml min-1 m-2 were observed in well-mixed systems, and just over 350 ml min-1 m-2 in flow through tubular systems. Oxygen flux was proportional to the oxygen partial pressure inside the HFM over the tested range and increased with mixing of the bulk liquid. Some bubbles were observed at the higher pressures (1.9 bar) and when bulk liquid dissolved oxygen concentrations were high. High-frequency ultrasound was applied to detect and count individual bubbles, but no increase from background levels was detected during lower pressure operation. A conceptual model of the oxygen transport was developed and validated. Model parametric sensitivity studies demonstrated that diffusion through the thin fiber walls was a significant resistance to mass transfer, and that promoting convection around the fibers should enable physiologically relevant oxygen supply. This study indicates that a device is within reach that is capable of delivering greater than 10% of a patient's basal oxygen needs in a configuration that readily fits intravascularly.

Detection and Quantification of Enteric Pathogens in Aerosols Near Open Wastewater Canals in Cities with Poor Sanitation.

Urban sanitation infrastructure is inadequate in many low-income countries, leading to the presence of highly concentrated, uncontained fecal waste streams in densely populated areas. Combined with mechanisms of aerosolization, airborne transport of enteric microbes and their genetic material is possible in such settings but remains poorly characterized. We detected and quantified enteric pathogen-associated gene targets in aerosol samples near open wastewater canals (OWCs) or impacted (receiving sewage or wastewater) surface waters and control sites in La Paz, Bolivia; Kanpur, India; and Atlanta, USA, via multiplex reverse-transcription qPCR (37 targets) and ddPCR (13 targets). We detected a wide range of enteric targets, some not previously reported in extramural urban aerosols, with more frequent detections of all enteric targets at higher densities in La Paz and Kanpur near OWCs. We report density estimates ranging up to 4.7 × 102 gc per mair3 across all targets including heat-stable enterotoxigenic Escherichia coli, Campylobacter jejuni, enteroinvasive E. coli/Shigella spp., Salmonella spp., norovirus, and Cryptosporidium spp. Estimated 25, 76, and 0% of samples containing positive pathogen detects were accompanied by culturable E. coli in La Paz, Kanpur, and Atlanta, respectively, suggesting potential for viability of enteric microbes at the point of sampling. Airborne transmission of enteric pathogens merits further investigation in cities with poor sanitation.

Antimicrobial resistance genes are enriched in aerosols near impacted urban surface waters in La Paz, Bolivia.

Antibiotic resistance poses a major global health threat. Understanding emergence and dissemination of antibiotic resistance in environmental media is critical to the design of control strategies. Because antibiotic resistance genes (ARGs) may be aerosolized from contaminated point sources and disseminated more widely in localized environments, we assessed ARGs in aerosols in urban La Paz, Bolivia, where wastewater flows in engineered surface water channels through the densely populated urban core. We quantified key ARGs and a mobile integron (MI) via ddPCR and E. coli spp. as a fecal indicator by culture over two years during both the rainy and dry seasons in sites near wastewater flows. ARG targets represented major antibiotic groups-tetracyclines (tetA), fluoroquinolines (qnrB), and beta-lactams (blaTEM)-and an MI (intI1) represented the potential for mobility of genetic material. Most air samples (82%) had detectable targets above the experimentally determined LOD: most commonly blaTEM and intI1 (68% and 47% respectively) followed by tetA and qnrB (17% and 11% respectively). ARG and MI densities in positive air samples ranged from 1.3 × 101 to 6.6 × 104 gene copies/m3 air. Additionally, we detected culturable E. coli in the air (52% of samples <1 km from impacted surface waters) with an average density of 11 CFU/m3 in positive samples. We observed decreasing density of blaTEM with increasing distance up to 150 m from impacted surface waters. To our knowledge this is the first study conducting absolute quantification and a spatial analysis of ARGs and MIs in ambient urban air of a city with contaminated surface waters. Environments in close proximity to urban wastewater flows in this setting may experience locally elevated concentrations of ARGs, a possible concern for the emergence and dissemination of antimicrobial resistance in cities with poor sanitation.

Technical evaluation and optimization of a mobile septage treatment unit.

A mobile septage treatment unit was built in India using readily available filters and membranes (mesh fabric, sand, granular activated carbon (GAC), microfilter, ultrafilter) and installed on the bed of a small truck. The target application was emptying of septic or sewage holding tanks and concentration of suspended solids while generating a liquid that could be discharged. The system was evaluated for operational and treatment performance while processing septage in the field at 108 sites in Tamil Nadu, India. After one phase of evaluation (Phase I), the system was improved and three replicate systems with slight modifications were fabricated for a second round of evaluation (Phase II) alongside the original, but modified unit. In Phase I, 105 m3 of septage was processed at an average flow of 623 L h-1 and with high removal efficiencies: 83% chemical oxygen demand (COD), 75% total suspended solids (TSS), and 98.4% total coliform (TC). In Phase II, the original and three new systems combined treated 168 m3 of septage. One of the new systems doubled in capacity and processed septage at an average flow of 2700 L h-1 while the other three averaged 1290 L h-1. The removal efficiencies in Phase II were 80% COD, 81% TSS, and 99% TC averaged between the four systems. Pass through of soluble contaminants (e.g. soluble COD, NH3-N) remain the primary challenge for treatment performance. Success may be limited with some septage due to seasonality, location, or septage age, and further validation and optimization may be necessary. However, the septage in this study was treated to local standards, and the system offers a method of onsite treatment while reducing the need of costly and often inefficient septage emptying services. Further, the system can be produced at a cost competitive to traditional septage hauling trucks.

Environmental and Aerosolized Severe Acute Respiratory Syndrome Coronavirus 2 Among Hospitalized Coronavirus Disease 2019 Patients.

During April and May 2020, we studied 20 patients hospitalized with coronavirus disease 2019 (COVID-19), their hospital rooms (fomites and aerosols), and their close contacts for molecular and culture evidence of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). Among >400 samples, we found molecular evidence of virus in most sample types, especially the nasopharyngeal (NP), saliva, and fecal samples, but the prevalence of molecular positivity among fomites and aerosols was low. The agreement between NP swab and saliva positivity was high (89.5%; κ = 0.79). Two NP swabs collected from patients on days 1 and 7 post-symptom onset had evidence of infectious virus (2 passages over 14 days in Vero E6 cells). In summary, the low molecular prevalence and lack of viable SARS-CoV-2 virus in fomites and air samples implied low nosocomial risk of SARS-CoV-2 transmission through inanimate objects or aerosols.

Novel Integrated Biotrickling Filter-Anammox Bioreactor System for the Complete Treatment of Ammonia in Air with Nitrification and Denitrification.

An integrated biotrickling filter-anammox bioreactor system for the complete treatment of ammonia in air with conversion to nitrogen gas without the supply of an extraneous electron donor for denitrification was established. Partial nitritation (i.e., conversion of ammonium to nitrite) was successfully achieved in the biotrickling filter (BTF) through free ammonia (FA) and free nitrous acid (FNA) inhibition on nitrite-oxidizing bacteria (NOB). During transients, while increasing nitrogen loading, FA was the main inhibitor of ammonia-oxidizing bacteria (AOB) and NOB, while during a steady state, it was mainly FNA, which was responsible for inhibitory effects due to the accumulation of nitrite. Ammonia removal by the BTF reached 50 gN m-3 h-1 with 100% removal at an inlet concentration of 404 ppmv and a gas residence time of 21 s. Average removal of ammonia during stable operation was 95%. The anammox bioreactor was slightly undersized compared to the BTF and could remove 75% of total nitrogen discharged by the BTF when the two reactors were connected and liquid was in one-pass mode. This undersizing caused accumulation of nitrite in the system when liquid was circled in a quasi-closed loop, which gradually inhibited the activity of anammox bacteria. Overall, this study demonstrates that ammonia in air can be effectively treated and converted to harmless nitrogen gas without an external electron donor supply using a biotrickling filter combined with an anammox bioreactor.

Fecal Malodor Detection Using Low-Cost Electrochemical Sensors.

Technology innovation in sanitation is needed for the 4.2 billion people worldwide, lacking safely managed sanitation services. A major requirement for the adoption of these technologies is the management of malodor around toilet and treatment systems. There is an unmet need for a low-cost instrumented technology for detecting the onset of sanitation malodor and triggering corrective actions. This study combines sensory data with low-cost gas sensor data on malodor emanating from feces. The response of 10 commercial electrochemical gas sensors was collected alongside olfactometric measurements. Odor from fecal specimens at different relevant dilution as well as specimens with pleasant odors as a control were evaluated for a total of 64 responses. Several of the sensors responded positively to the fecal odor, with the formaldehyde, hydrogen sulfide, and ammonia sensors featuring the highest signal to noise ratio. A positive trend was observed between the sensors' responses and the concentration of the odorant and with odor intensity, but no clear correspondence with dilution to threshold (D/T) values was found. Selected sensors were responsive both above and below the intensity values used as the cutoff for offensive odor, suggesting the possibility of using those sensors to differentiate odor offensiveness based just on the magnitude of their response. The specificity of the sensors suggested that discrimination between the selected non-fecal and fecal odors was possible. This study demonstrates that some of the evaluated sensors could be used to assemble a low-cost malodor warning system.

Miniaturized Biotrickling Filters and Capillary Microbioreactors for Process Intensification of VOC Treatment with Intended Application to Indoor Air.

Typical biofilters and biotrickling filters used for volatile organic compounds (VOCs) control have treatment rates limited to 30-200 g m-3 h-1, mostly because they are exposed to dilute VOC streams, have moderate biomass density and activity, and moderate mass transfer coefficients. For these reasons and the concern over releasing bioaerosols and humidity, traditional biofilters and biotrickling filters are not ideal for the treatment of indoor air. Here we report on the development and evaluation of microbioreactors for the intensive treatment of VOCs that could be used for indoor air quality control, when coupled with a VOC microconcentrator (developed separately). The microconcentrator will function to adsorb VOCs from indoor air and release them to the microbioreactor at a higher concentration. The miniaturized bioreactors, with maximized surface area-to-volume ratios, allow for increased mixing and mass transfer of pollutants to the biofilm, resulting in a greater degradation rate of the VOCs. Three different microbioreactors were designed, constructed and their performance for removing vapors of toluene and methanol was assessed. Results showed that they were able to achieve maximum elimination capacities (ECs) for methanol around 1000 g m-3 h-1, 780 g m-3 h-1, and 12 600 g m-3 h-1 for the glass beads packed bed, polyurethane (PU) foam biotrickling filters and capillary microbioreactor, respectively, and around 120 g m-3 h-1, 250 g m-3 h-1 and 3050 g m-3 h-1, respectively, when treating toluene vapors. These values, especially for the capillary microbioreactor, are 40-80 times greater than the rates generally obtained in conventional biofilters and biotrickling filters. The interphase mass transfer coefficient (KLa) was determined. The capillary microbioreactor had values 13-17 times greater than the other two bioreactors, suggesting that improved mass transfer could have contributed to the very high performance observed in the capillary microbioreactor. The results demonstrate that microbioreactors are promising novel technologies for controlling small amounts of organic pollutants.

Quantification of Mercury Bioavailability for Methylation Using Diffusive Gradient in Thin-Film Samplers.

Mercury-contaminated sediment and water contain various Hg species, with a small fraction available for microbial conversion to the bioaccumulative neurotoxin monomethylmercury (MeHg). Quantification of this available Hg pool is needed to prioritize sites for risk management. This study compared the efficacy of diffusive gradient in thin-film (DGT) passive samplers to a thiol-based selective extraction method with glutathione (GSH) and conventional filtration (<0.2 µm) as indicators of Hg bioavailability. Anaerobic sediment slurry microcosms were amended with isotopically labeled inorganic Hg "endmembers" (dissolved Hg2+, Hg-humic acid, Hg-sorbed to FeS, HgS nanoparticles) with a known range of bioavailability and methylation potentials. Net MeHg production (expressed as percent of total Hg as MeHg) over 1 week correlated with mass accumulation of Hg endmembers on the DGTs and only sometimes correlated with the 0.2 µm filter passing Hg fraction and the GSH-extractable Hg fraction. These results suggest for the first time that inorganic Hg uptake in DGTs may indicate bioavailability for methylating microbes. Moreover, the methylating microbial community assessed by hgcA gene abundance was not always consistent with methylation rates between the experiments, indicating that knowledge of the methylating community should target the transcript or protein level. Altogether, these results suggest that DGTs could be used to quantify the bioavailable Hg fraction as part of a method to assess net MeHg production potential in the environment.

Water Availability for Shale Gas Development in Sichuan Basin, China.

Unconventional shale gas development holds promise for reducing the predominant consumption of coal and increasing the utilization of natural gas in China. While China possesses some of the most abundant technically recoverable shale gas resources in the world, water availability could still be a limiting factor for hydraulic fracturing operations, in addition to geological, infrastructural, and technological barriers. Here, we project the baseline water availability for the next 15 years in Sichuan Basin, one of the most promising shale gas basins in China. Our projection shows that continued water demand for the domestic sector in Sichuan Basin could result in high to extremely high water stress in certain areas. By simulating shale gas development and using information from current water use for hydraulic fracturing in Sichuan Basin (20,000-30,000 m(3) per well), we project that during the next decade water use for shale gas development could reach 20-30 million m(3)/year, when shale gas well development is projected to be most active. While this volume is negligible relative to the projected overall domestic water use of ∼36 billion m(3)/year, we posit that intensification of hydraulic fracturing and water use might compete with other water utilization in local water-stress areas in Sichuan Basin.

On-Site Fecal Sludge Treatment with the Anaerobic Digestion Pasteurization Latrine.

The Anaerobic Digestion Pasteurization Latrine (ADPL) is a self-contained and energy neutral on-site sanitation system using anaerobic digestion of fecal sludge to generate biogas and then uses the biogas to pasteurize the digester effluent at 65-75°C to produce a safe effluent that can be reused locally as a fertilizer. Two ADPL systems were installed on residential plots with 17 and 35 residents in a peri-urban area outside of Eldoret, Kenya. Each system comprised three toilets built above a floating dome digester and one heat pasteurization system to sanitize the digested effluent. ADPLs are simple systems, with no moving parts and relying on gravity-induced flows. Adoption at the two sites was successful, and residents reported that the systems had little to no odor or flies. ADPLs were monitored for biogas production and temperatures in the pasteurization system. ADPLs serving 17 and 35 residents produced on average 16 and 11 Lbiogas/person/day (maximum of 20 and 15 Lbiogas/p/d), respectively. The temperature in the sterilization system was greater than 65°C on 58% and 87% of sampling days during the most stable period of operation. Treated effluent was analyzed periodically for chemical oxygen demand (COD), biochemical oxygen demand (BOD), total ammonia nitrogen (TAN), pH, and fecal coliform (FC). On average, the effluent at the two locations contained 4,540 and 6,450 mg COD/L (an 85% or 89% reduction of the estimated input), 2,050 and 3,970 mg BOD/L, and 2,420 and 4,760 mg NH3-N, respectively, and greater than 5 log reductions of FC (nondetectable) in the sterilization tank. Results from this field study show that anaerobic digestion of minimally diluted fecal sludge can provide enough energy to pasteurize digester effluent and that the ADPL may be a suitable option for on-site fecal sludge treatment.

Reduction of invasive bacteria in ethanol fermentations using bacteriophages.

Invasive Lactobacillus bacteria inhibit ethanol fermentations and reduce final product yields. Due to the emergence of antibiotic resistant strains of Lactobacillus spp., alternative disinfection strategies are needed for ethanol fermentations. The feasibility of using the bacteriophage (phage) 8014-B2 to control Lactobacillus plantarum in ethanol fermentations by Saccharomyces cerevisiae was investigated. In 48 h media-based shake flask fermentations, phages achieved greater than 3-log inactivation of L. plantarum, protected final ethanol yields, and maintained yeast viability. The phage-based bacterial disinfection rates depended on both the initial phage and bacterial concentrations. Furthermore, a simple set of kinetic equations was used to model the yeast, bacteria, phage, reducing sugars, and ethanol concentrations over the course of 48 h, and the various kinetic parameters were determined. Taken together, these results demonstrate the applicability of phages to reduce L. plantarum contamination and to protect final product yields in media-based fermentations.

Biocatalytic coatings for air pollution control: a proof of concept study on VOC biodegradation.

Although biofilm-based biotechnologies exhibit a large potential as solutions for off-gas treatment, the high water content of biofilms often causes pollutant mass transfer limitations, which ultimately limit their widespread application. The present study reports on the proof of concept of the applicability of bioactive latex coatings for air pollution control. Toluene vapors served as a model volatile organic compound (VOC). The results showed that Pseudomonas putida F1 cells could be successfully entrapped in nanoporous latex coatings while preserving their toluene degradation activity. Bioactive latex coatings exhibited toluene specific biodegradation rates 10 times higher than agarose-based biofilms, because the thin coatings were less subject to diffusional mass transfer limitations. Drying and pollutant starvation were identified as key factors inducing a gradual deterioration of the biodegradation capacity in these innovative coatings. This study constitutes the first application of bioactive latex coatings for VOC abatement. These coatings could become promising means for air pollution control.

Natural Gas Residual Fluids: Sources, Endpoints, and Organic Chemical Composition after Centralized Waste Treatment in Pennsylvania.

Volumes of natural gas extraction-derived wastewaters have increased sharply over the past decade, but the ultimate fate of those waste streams is poorly characterized. Here, we sought to (a) quantify natural gas residual fluid sources and endpoints to bound the scope of potential waste stream impacts and (b) describe the organic pollutants discharged to surface waters following treatment, a route of likely ecological exposure. Our findings indicate that centralized waste treatment facilities (CWTF) received 9.5% (8.5 × 10(8) L) of natural gas residual fluids in 2013, with some facilities discharging all effluent to surface waters. In dry months, discharged water volumes were on the order of the receiving body flows for some plants, indicating that surface waters can become waste-dominated in summer. As disclosed organic compounds used in high volume hydraulic fracturing (HVHF) vary greatly in physicochemical properties, we deployed a suite of analytical techniques to characterize CWTF effluents, covering 90.5% of disclosed compounds. Results revealed that, of nearly 1000 disclosed organic compounds used in HVHF, only petroleum distillates and alcohol polyethoxylates were present. Few analytes targeted by regulatory agencies (e.g., benzene or toluene) were observed, highlighting the need for expanded and improved monitoring efforts at CWTFs.

Thiol-Based Selective Extraction Assay to Comparatively Assess Bioavailable Mercury in Sediments.

Bioaccumulation of methylmercury in the aquatic food web is governed in part by the methylation of inorganic divalent mercury (Hg(II)) by anaerobic microorganisms. In sulfidic settings, a small fraction of total Hg(II) is typically bioavailable to methylating microorganisms. Quantification of this fraction is difficult due to uncertainties in the speciation of Hg(II) and the mechanisms of uptake by methylating microbes. However, recent studies have shown that the bioavailable fraction is likely to include a portion of Hg(II) associated with solid phases, that is, nanostructured mercuric sulfides. Moreover, addition of thiols to suspensions of methylating cultures coincides with increased uptake into cells and methylmercury production. Here, we present a thiol-based selective extraction assay to provide information on the bioavailable Hg fraction in sediments. In the procedure, sediment samples were exposed to a nitrogen-purged solution of glutathione (GSH) for 30 min and the amount of GSH-leachable mercury was quantified. In nine sediment samples from a marine location, the relative GSH-leachable mercury concentration was strongly correlated to the relative amount of methylmercury in the sediments (r2=0.91, p<0.0001) across an order of magnitude of methylmercury concentration values. The approach was further applied to anaerobic sediment slurry microcosm experiments in which sediments were cultured under the same microbial growth conditions but were amended with multiple forms of Hg with a known spectrum of bioavailability. GSH-leachable Hg concentrations increased with observed methylmercury concentrations in the microcosms, matching the trend of species bioavailability in our previous work. Results suggest that a thiol-based selective leaching approach is an improvement compared with other proposed methods to assess Hg bioavailability in sediment and that this approach could provide a basis for comparison of sites where Hg methylation is a concern.

Net methylation of mercury in estuarine sediment microcosms amended with dissolved, nanoparticulate, and microparticulate mercuric sulfides.

The production of methylmercury (MeHg) by anaerobic microorganisms depends in part on the speciation and bioavailability of inorganic mercury to these organisms. Our previous work with pure cultures of methylating bacteria has demonstrated that the methylation potential of mercury decreased during the aging of mercuric sulfides (from dissolved to nanoparticulate and microcrystalline HgS). The objective of this study was to understand the relationship between mercury sulfide speciation and methylation potential in experiments that more closely simulate the complexity of sediment settings. The study involved sediment slurry microcosms that represented a spectrum of salinities in an estuary and were each amended with different forms of mercuric sulfides: dissolved Hg and sulfide, nanoparticulate HgS (3-4 nm in diameter), and microparticulate HgS (>500 nm). The results indicated that net MeHg production was influenced by both the activity of sulfate-reducing microorganisms (roughly represented by the rate of sulfate loss) and the bioavailability of mercury. In the presence of abundant sulfate and carbon sources (supporting relatively high microbial activity), net MeHg production in the slurries amended with dissolved Hg was greater than in slurries amended with nano-HgS, similar to previous experiments with pure bacterial cultures. In microcosms with minimal microbial activity (indicated by low rates of sulfate loss), the addition of either dissolved Hg or nano-HgS resulted in similar amounts of net MeHg production. For all slurries receiving micro-HgS, MeHg production did not exceed abiotic controls. In slurries amended with dissolved and nano-HgS, mercury was mainly partitioned to bulk-scale mineral particles and colloids, indicating that Hg bioavailability was not simply related to dissolved Hg concentration or speciation. Overall, the results suggest that models for mercury methylation potential in the environment will need to balance the relative contributions of mercury speciation and activity of methylating microorganisms.

Experimental evaluation of a full-scale in-duct UV germicidal irradiation system for bioaerosols inactivation.

Bioaerosols control techniques, especially ultraviolet germicidal irradiation (UVGI) are gaining attention due to increasing needs for controlling of health risk caused by airborne biocontaminants. The effectiveness of a full-scale in-duct UVGI air disinfection system was investigated. One bacterium, a wild type Escherichia coli, and three fungal spores, Penicillium aragonense, Rhodotorula glutinis, and Cladosporium sp., were selected as test organisms and their inactivation under different conditions representative of a real application in HVAC systems were investigated. The results demonstrated that inactivation of airborne E. coli by the UVGI system was extremely effective, with >99.5 % of the input E. coli inactivated at a residence time lower of 0.36 s in the disinfection section. Airborne fungal spores were less susceptible to UV irradiation than E. coli. Under same conditions, viable counts reduction of P. aragonense, R. glutinis, and Cladosporium sp. spores were 53 %, 63 % and 73 %, respectively. The effect of UV light intensity, air flowrate and relative humidity were analyzed separately. A simplified model based on redefinition of the parameters in the classical inactivation kinetic equation was used to simulate the inactivation of airborne contaminants in the in-duct system under different conditions. The results showed that the simplified model was adequate to estimate disinfection efficacy of different bioaerosols by the UVGI system and that such in-duct systems can provide significant control of bioaerosols.

Optimization of the IntraVascular Oxygenator Catheter Using Angular Oscillation.

We demonstrate a methodology which both improves oxygen transport and reduces or eliminates bubble formation in a novel hyperbaric membrane oxygenator catheter model system. Angular oscillations were introduced to a bundle of hollow fiber membranes (HFMs) supplied with hyperbaric 100% oxygen at average gauge pressures up to 0.35 barg. Oscillating bundles enabled delivery of an oxygen flux of up to 400 mL min-1 m-2 in an aqueous solution, a doubling over a previous non-oscillating setup. Similarly, the addition of angular oscillations facilitated a five-fold reduction in pressure to achieve similar oxygen flux. The increased angular speed of oscillation improved flux, while the addition of angular micro-oscillation variations resulted in flux reductions of 7-20% compared to continuous macro-oscillation only, depending on mixing conditions. However, semi-quantitative visual observation demonstrated that angular oscillations reduced or eliminated the instance of oxygen bubble formation on the HFMs. The modeled mass transfer coefficients indicated a quasi linear relationship between rotational velocity and flux, suggesting that faster oscillation speeds could further improve oxygen mass transport allowing for HFM bundles to maintain high oxygen fluxes while eliminating bubble formation. This encourages further development of our compact oxygenating catheter that could be used intravascularly.

Mechanisms regulating mercury bioavailability for methylating microorganisms in the aquatic environment: a critical review.

Mercury is a potent neurotoxin for humans, particularly if the metal is in the form of methylmercury. Mercury is widely distributed in aquatic ecosystems as a result of anthropogenic activities and natural earth processes. A first step toward bioaccumulation of methylmercury in aquatic food webs is the methylation of inorganic forms of the metal, a process that is primarily mediated by anaerobic bacteria. In this Review, we evaluate the current state of knowledge regarding the mechanisms regulating microbial mercury methylation, including the speciation of mercury in environments where methylation occurs and the processes that control mercury bioavailability to these organisms. Methylmercury production rates are generally related to the presence and productivity of methylating bacteria and also the uptake of inorganic mercury to these microorganisms. Our understanding of the mechanisms behind methylation is limited due to fundamental questions related to the geochemical forms of mercury that persist in anoxic settings, the mode of uptake by methylating bacteria, and the biochemical pathway by which these microorganisms produce and degrade methylmercury. In anoxic sediments and water, the geochemical forms of mercury (and subsequent bioavailability) are largely governed by reactions between Hg(II), inorganic sulfides, and natural organic matter. These interactions result in a mixture of dissolved, nanoparticulate, and larger crystalline particles that cannot be adequately represented by conventional chemical equilibrium models for Hg bioavailability. We discuss recent advances in nanogeochemistry and environmental microbiology that can provide new tools and unique perspectives to help us solve the question of how microorganisms methylate mercury. An understanding of the factors that cause the production and degradation of methylmercury in the environment is ultimately needed to inform policy makers and develop long-term strategies for controlling mercury contamination.

Quantitative risk assessment of COVID-19 aerosol transmission indoors: a mechanistic stochastic web application.

An increasing body of literature suggests that aerosol inhalation plays a primary role in COVID-19 transmission, particularly in indoor settings. Mechanistic stochastic models can help public health professionals, engineers, and space planners understand the risk of aerosol transmission of COVID-19 to mitigate it. We developed such model and a user-friendly web application to meet the need of accessible risk assessment tools during the COVID-19 pandemic. We built our model based on the Wells-Riley model of respiratory disease transmission, using quanta emission rates obtained from COVID-19 outbreak investigations. In this report, three modelled scenarios were evaluated and compared to epidemiological studies looking at similar settings: classrooms, weddings, and heavy exercise sessions. We found that the risk of long-range aerosol transmission increased 309-332% when people were not wearing masks, and 424-488% when the room was poorly ventilated in addition to no masks being worn across the scenarios. Also, the risk of transmission could be reduced by ∼40-60% with ventilation rates of 5 ACH for 1-4 h exposure events, and ∼70% with ventilation rates of 10 ACH for 4 h exposure events. Relative humidity reduced the risk of infection (inducing viral inactivation) by a maximum of ∼40% in a 4 h exposure event at 70% RH compared to a dryer indoor environment with 25% RH. Our web application has been used by more than 1000 people in 52 countries as of September 1st, 2021. Future work is needed to obtain SARS-CoV-2 dose-response functions for more accurate risk estimates.