Giant and Tunable Excitonic Optical Anisotropy in Single-Crystal Halide Perovskites.

During the last years, giant optical anisotropy has demonstrated its paramount importance for light manipulation. In spite of recent advances in the field, the achievement of continuous tunability of optical anisotropy remains an outstanding challenge. Here, we present a solution to the problem through the chemical alteration of halogen atoms in single-crystal halide perovskites. As a result, we manage to continually modify the optical anisotropy by 0.14. We also discover that the halide perovskite can demonstrate optical anisotropy up to 0.6 in the visible range─the largest value among non-van der Waals materials. Moreover, our results reveal that this anisotropy could be in-plane and out-of-plane depending on perovskite shape─rectangular and square. As a practical demonstration, we have created perovskite anisotropic nanowaveguides and shown a significant impact of anisotropy on high-order guiding modes. These findings pave the way for halide perovskites as a next-generation platform for tunable anisotropic photonics.

Photo Stabilization of p-i-n Perovskite Solar Cells with Bathocuproine: MXene.

Interface engineering is one of the promising strategies for the long-term stabilization of perovskite solar cells (PSCs), preventing chemical decomposition induced by external agents and promoting fast charge transfer. Recently, MXenes-2D structured transition metal carbides and nitrides with various functionalization (O, -F, -OH) have demonstrated high potential for mastering the work function in halide perovskite absorbers and have significantly improved the n-type charge collection in solar cells. This work demonstrates that MXenes allow for efficient stabilization of PSCs besides improving their performances. A mixed composite bathocuproine:MXene, that is, (BCP:MXene) interlayer, is introduced at the interface between an electron-transport layer (ETL) and a metal cathode in the p-i-n device structure. The investigation demonstrates that the use of BCP:MXene interlayer slightly increases the power conversation efficiency (PCE) for PSCs (from 16.5 for reference to 17.5%) but dramatically improves the out of Glove-Box stability. Under ISOS-L-2 light soaking stress at 63 ± 1.5 °C, the T80 (time needed to reduce efficiency down to 80% of the initial one) period increases from 460 to > 2300 hours (h).

Versatile Electroluminescence Color-Tuning Strategy of an Efficient Light-Emitting Electrochemical Cell (LEC) by an Ionic Additive.

The color-tuning strategies of solid-state light-emitting devices (ss-LEDs) are mainly focused on engineering molecular structures. In this paper, for the first time, we developed a facile strategy for tuning the electroluminescence (EL) color from orange to green through the addition of the ionic additive TBAP (tetrabutylammonium perchlorate). To achieve the active ionic emissive compound for use in a light-emitting electrochemical cell (LEC), the neutral biscyclometalated bromo tetrazole iridium(III) [Ir(ppy)2(BrTz)] was exchanged to its cationic complex, [Ir(ppy)2(BrTz-Me)]ClO4 (ppy = 2-phenyl pyridine, BrTz = 4-bromo-2-pyridine tetrazole, BrTz-Me = 4-bromo-2-pyridine methyl tetrazole) with a new synthetic strategy. This method allows employing neutral Ir-cyclometalated complexes, which are ruled out for use in LECs because of their non-ionic behaviors. In the following, an LEC based on the new cationic [Ir(ppy)2(BrTz-Me)]ClO4 as the emissive layer was fabricated between the FTO (fluorine-doped tin oxide) anode and Ga:In alloy cathode without using any additive or polymers, which makes this configuration the simplest ss-LED so far. By adding the ionic additives, the electroluminescence characteristics of [Ir(ppy)2(BrTz-Me)]ClO4 were dramatically increased, including luminance (L) from 162.8 cd/m2 for the device with an additive to 212.9 and 355.9 cd/m2 for devices containing LiTFSI (bis(trifluoromethane)sulfonamide lithium salt) and TBAP, respectively. In particular, when TBAP was added to the [Ir(ppy)2(BrTz-Me)]ClO4 complex, the irradiance was significantly increased from 166.4 to 220.8 µW/cm2 with an efficacy of 1.78 cd/A and external quantum efficiency (EQE) value of 2.14%. The obtained EL results clearly showed that adding TBAP and LiTFSI significantly improved the electroluminescence characteristics and tuned the electroluminescence color.

Changes in the hydrogen nuclear kinetic energy across the several phases of methylammonium lead tribromide.

We present an experimental investigation of methylammonium lead tribromide single crystals in the orthorhombic, tetragonal, and cubic phases based on inelastic and deep inelastic neutron scattering experiments. We show how the average hydrogen nuclear kinetic energy, mainly affected by zero-point vibrational energies, shows differences larger compared to the changes simply related to temperature effects when moving from one phase to another. In particular, the Gaussian contribution to the average nuclear kinetic energy is larger in the tetragonal phase compared to the cubic and orthorhombic ones. Moreover, we find that the vibrational densities of states of MAPbBr3 single crystals in the orthorhombic phase are compatible with previously reported results on powder samples, and that the only vibrational modes that show slightly different frequencies compared to MAPbI3 are those in the energy range between 100 and 300 cm-1, related to librational/rotational modes. As these shifts are of about 10 cm-1 and do not affect any higher-energy vibrational mode, we conclude that the zero-point energies and average nuclear kinetic energies in the two-hybrid organic/inorganic perovskites are expected to be approximately the same within a harmonic framework.

Solution-processed two-dimensional materials for next-generation photovoltaics.

In the ever-increasing energy demand scenario, the development of novel photovoltaic (PV) technologies is considered to be one of the key solutions to fulfil the energy request. In this context, graphene and related two-dimensional (2D) materials (GRMs), including nonlayered 2D materials and 2D perovskites, as well as their hybrid systems, are emerging as promising candidates to drive innovation in PV technologies. The mechanical, thermal, and optoelectronic properties of GRMs can be exploited in different active components of solar cells to design next-generation devices. These components include front (transparent) and back conductive electrodes, charge transporting layers, and interconnecting/recombination layers, as well as photoactive layers. The production and processing of GRMs in the liquid phase, coupled with the ability to "on-demand" tune their optoelectronic properties exploiting wet-chemical functionalization, enable their effective integration in advanced PV devices through scalable, reliable, and inexpensive printing/coating processes. Herein, we review the progresses in the use of solution-processed 2D materials in organic solar cells, dye-sensitized solar cells, perovskite solar cells, quantum dot solar cells, and organic-inorganic hybrid solar cells, as well as in tandem systems. We first provide a brief introduction on the properties of 2D materials and their production methods by solution-processing routes. Then, we discuss the functionality of 2D materials for electrodes, photoactive layer components/additives, charge transporting layers, and interconnecting layers through figures of merit, which allow the performance of solar cells to be determined and compared with the state-of-the-art values. We finally outline the roadmap for the further exploitation of solution-processed 2D materials to boost the performance of PV devices.

Pursuing the Diffraction Limit with Nano-LED Scanning Transmission Optical Microscopy.

Recent research into miniaturized illumination sources has prompted the development of alternative microscopy techniques. Although they are still being explored, emerging nano-light-emitting-diode (nano-LED) technologies show promise in approaching the optical resolution limit in a more feasible manner. This work presents the exploration of their capabilities with two different prototypes. In the first version, a resolution of less than 1 µm was shown thanks to a prototype based on an optically downscaled LED using an LED scanning transmission optical microscopy (STOM) technique. This research demonstrates how this technique can be used to improve STOM images by oversampling the acquisition. The second STOM-based microscope was fabricated with a 200 nm GaN LED. This demonstrates the possibilities for the miniaturization of on-chip-based microscopes.

Nano illumination microscopy: a technique based on scanning with an array of individually addressable nanoLEDs.

In lensless microscopy, spatial resolution is usually provided by the pixel density of current digital cameras, which are reaching a hard-to-surpass pixel size / resolution limit over 1 µm. As an alternative, the dependence of the resolving power can be moved from the detector to the light sources, offering a new kind of lensless microscopy setups. The use of continuously scaled-down Light-Emitting Diode (LED) arrays to scan the sample allows resolutions on order of the LED size, giving rise to compact and low-cost microscopes without mechanical scanners or optical accessories. In this paper, we present the operation principle of this new approach to lensless microscopy, with simulations that demonstrate the possibility to use it for super-resolution, as well as a first prototype. This proof-of-concept setup integrates an 8 × 8 array of LEDs, each 5 × 5 µm2 pixel size and 10 µm pitch, and an optical detector. We characterize the system using Electron-Beam Lithography (EBL) pattern. Our prototype validates the imaging principle and opens the way to improve resolution by further miniaturizing the light sources.

Doping Strategy for Efficient and Stable Triple Cation Hybrid Perovskite Solar Cells and Module Based on Poly(3-hexylthiophene) Hole Transport Layer.

As the hole transport layer (HTL) for perovskite solar cells (PSCs), poly(3-hexylthiophene) (P3HT) has been attracting great interest due to its low-cost, thermal stability, oxygen impermeability, and strong hydrophobicity. In this work, a new doping strategy is developed for P3HT as the HTL in triple-cation/double-halide ((FA1-x-y MAx Csy )Pb(I1-x Brx )3 ) mesoscopic PSCs. Photovoltaic performance and stability of solar cells show remarkable enhancement using a composition of three dopants Li-TFSI, TBP, and Co(III)-TFSI reaching power conversion efficiencies of 19.25% on 0.1 cm2 active area, 16.29% on 1 cm2 active area, and 13.3% on a 43 cm2 active area module without using any additional absorber layer or any interlayer at the PSK/P3HT interface. The results illustrate the positive effect of a cobalt dopant on the band structure of perovskite/P3HT interfaces leading to improved hole extraction and a decrease of trap-assisted recombination. Non-encapsulated large area devices show promising air stability through keeping more than 80% of initial efficiency after 1500 h in atmospheric conditions (relative humidity ≈ 60%, r.t.), whereas encapsulated devices show more than >500 h at 85 °C thermal stability (>80%) and 100 h stability against continuous light soaking (>90%). The boosted efficiency and the improved stability make P3HT a good candidate for low-cost large-scale PSCs.

Energetic disorder in perovskite/polymer solar cells and its relationship with the interfacial carrier losses.

Previous reports have observed a direct relationship between the polymer poly(3-hexylthiophene) molecular weight (MW) and the perovskite solar cell (PSC) efficiency. Herein, we analyse how the differences in MW and the differences in energetic disorder influence the interfacial carrier losses in the PSCs under operation conditions and explain the observed differences. This article is part of a discussion meeting issue 'Energy materials for a low carbon future'.

Carrier transport and emission efficiency in InGaN quantum-dot based light-emitting diodes.

We present a study of blue III-nitride light-emitting diodes (LEDs) with multiple quantum well (MQW) and quantum dot (QD) active regions (ARs), comparing experimental and theoretical results. The LED samples were grown by metalorganic vapor phase epitaxy, utilizing growth interruption in the hydrogen/nitrogen atmosphere and variable reactor pressure to control the AR microstructure. Realistic configuration of the QD AR implied in simulations was directly extracted from HRTEM characterization of the grown QD-based structures. Multi-scale 2D simulations of the carrier transport inside the multiple QD AR have revealed a non-trivial pathway for carrier injection into the dots. Electrons and holes are found to penetrate deep into the multi-layer AR through the gaps between individual QDs and get into the dots via their side edges rather than via top and bottom interfaces. This enables a more homogeneous carrier distribution among the dots situated in different layers than among the laterally uniform quantum well (QWs) in the MQW AR. As a result, a lower turn-on voltage is predicted for QD-based LEDs, as compared to MQW ones. Simulations did not show any remarkable difference in the efficiencies of the MQW and QD-based LEDs, if the same recombination coefficients are utilized, i.e. a similar crystal quality of both types of LED structures is assumed. Measurements of the current-voltage characteristics of LEDs with both kinds of the AR have shown their close similarity, in contrast to theoretical predictions. This implies the conventional assumption of laterally uniform QWs not to be likely an adequate approximation for the carrier transport in MQW LED structures. Optical characterization of MQW and QD-based LEDs has demonstrated that the later ones exhibit a higher efficiency, which could be attributed to better crystal quality of the grown QD-based structures. The difference in the crystal quality explains the recently observed correlation between the growth pressure of LED structures and their efficiency and should be taken into account while further comparing performances of MQW and QD-based LEDs. In contrast to experimental results, our simulations did not reveal any advantages of using QD-based ARs over the MQW ones, if the same recombination constants are assumed for both cases. This fact demonstrates importance of accounting for growth-dependent factors, like crystal quality, which may limit the device performance. Nevertheless, a more uniform carrier injection into multi-layer QD ARs predicted by modeling may serve as the basis for further improvement of LED efficiency by lowering carrier density in individual QDs and, hence, suppressing the Auger recombination losses.

Stability of dye-sensitized solar cells under extended thermal stress.

In the last few decades, dye-sensitized solar cell (DSC) technology has been demonstrated to be a promising candidate for low cost energy production due to cost-effective materials and fabrication processes. Arguably, DSC stability is the biggest challenge for making this technology appealing for industrial exploitation. This work provides further insight into the stability of DSCs by considering specific dye-electrolyte systems characterized by Raman and impedance spectroscopy analysis. In particular, two ruthenium-based dyes, Z907 and Ru505, and two commercially available electrolytes, namely, the high stability electrolyte (HSE) and solvent-free Livion 12 (L-12), were tested. After 4700 h of thermal stress at 85 °C, the least stable device composed of Z907/HSE showed an efficiency degradation rate of ∼14%/1000 h, while the Ru505/L-12 system retained 96% of its initial efficiency by losing ∼1% each 1000 h. The present results show a viable route to stabilize the DSC technology under prolonged annealing conditions complying with the IEC standard requirements.

Role of Ferroelectric Nanodomains in the Transport Properties of Perovskite Solar Cells.

Metropolis Monte Carlo simulations are used to construct minimal energy configurations by electrostatic coupling of rotating dipoles associated with each unit cell of a perovskite CH3NH3PbI3 crystal. Short-range antiferroelectric order is found, whereas at scales of 8-10 nm, we observe the formation of nanodomains, strongly influencing the electrostatics of the device. The models are coupled to drift-diffusion simulations to study the actual role of nanodomains in the I-V characteristics, especially focusing on charge separation and recombination losses. We demonstrate that holes and electrons separate into different nanodomains following different current pathways. From our analysis we can conclude that even antiferroelectric ordering can ultimately lead to an increase of photoconversion efficiencies thanks to a decrease of trap-assisted recombination losses and the formation of good current percolation patterns along domain edges.

Efficiency Drop in Green InGaN/GaN Light Emitting Diodes: The Role of Random Alloy Fluctuations.

White light emitting diodes (LEDs) based on III-nitride InGaN/GaN quantum wells currently offer the highest overall efficiency for solid state lighting applications. Although current phosphor-converted white LEDs have high electricity-to-light conversion efficiencies, it has been recently pointed out that the full potential of solid state lighting could be exploited only by color mixing approaches without employing phosphor-based wavelength conversion. Such an approach requires direct emitting LEDs of different colors, including, in particular, the green-yellow range of the visible spectrum. This range, however, suffers from a systematic drop in efficiency, known as the "green gap," whose physical origin has not been understood completely so far. In this work, we show by atomistic simulations that a consistent part of the green gap in c-plane InGaN/GaN-based light emitting diodes may be attributed to a decrease in the radiative recombination coefficient with increasing indium content due to random fluctuations of the indium concentration naturally present in any InGaN alloy.

Vegetable-based dye-sensitized solar cells.

There is currently a large effort to improve the performance of low cost renewable energy devices. Dye-sensitized solar cells (DSSCs) are emerging as one of the most promising low cost photovoltaic technologies, addressing "secure, clean and efficient solar energy conversion". Vegetable dyes, extracted from algae, flowers, fruit and leaves, can be used as sensitizers in DSSCs. Thus far, anthocyanin and betalain extracts together with selected chlorophyll derivatives are the most successful vegetable sensitizers. This review analyses recent progress in the exploitation of vegetable dyes for solar energy conversion and compares them to the properties of synthetic dyes. We provide an in-depth discussion on the main limitation of cell performance e.g. dye degradation, effective electron injection from the dye into the conduction band of semiconducting nanoparticles, such as titanium dioxide and zinc oxide, outlining future developments for the use of vegetable sensitizers in DSSCs. We also discuss the cost of vegetable dyes and how their versatility can boost the advancement of new power management solutions, especially for their integration in living environments, making the practical application of such systems economically viable. Finally, we present our view on future prospects in the development of synthetic analogues of vegetable dyes as sensitizers in DSSCs.

Solid state perovskite solar modules by vacuum-vapor assisted sequential deposition on Nd:YVO4 laser patterned rutile TiO2 nanorods.

The past few years have witnessed remarkable progress in solution-processed methylammonium lead halide (CH3NH3PbX3, X = halide) perovskite solar cells (PSCs) with reported photoconversion efficiency (η) exceeding 20% in laboratory-scale devices and reaching up to 13% in their large area perovskite solar modules (PSMs). These devices mostly employ mesoporous TiO2 nanoparticles (NPs) as an electron transport layer (ETL) which provides a scaffold on which the perovskite semiconductor can grow. However, limitations exist which are due to trap-limited electron transport and non-complete pore filling. Herein, we have employed TiO2 nanorods (NRs), a material offering a two-fold higher electronic mobility and higher pore-filing compared to their particle analogues, as an ETL. A crucial issue in NRs' patterning over substrates is resolved by using precise Nd:YVO4 laser ablation, and a champion device with η ∼ 8.1% is reported via a simple and low cost vacuum-vapor assisted sequential processing (V-VASP) of a CH3NH3PbI3 film. Our experiments showed a successful demonstration of NRs-based PSMs via the V-VASP technique which can be applied to fabricate large area modules with a pin-hole free, smooth and dense perovskite layer which is required to build high efficiency devices.

Mimicking nature: a novel peptide-based bio-inspired approach for solar energy conversion.

A bioinspired approach is applied to photoelectric conversion devices. A 3(10)-helical hexapeptide bearing a pyrene unit is immobilized on a gold-covered TiO2 surface. The device is integrated for the first time in a dye-sensitized solar cell, exhibiting stability after several measurements. The approach could have promising applications in the field of optoelectronics.

Can video thermography improve differential diagnosis and therapy between basal cell carcinoma and actinic keratosis?

Various noninvasive techniques (dermoscopy, confocal microscopy, etc.) have been introduced to help the clinical diagnosis in nonmelanoma skin cancer. Among them, the high definition video thermographic technique (VTG) has recently been proposed. The aim of this study is to define the VTG patterns, respectively of actinic keratosis (AK) and basal cell carcinoma (BCC), and to compare these data with them of dermoscopy. The study included 36 patients with a total number of 135 lesions who underwent clinical, VTG, and dermoscopic examination. The VTG showed the presence of a hyperthermic pattern in all the cases of AK, while in the case of the BCC, the pattern was hypothermic. Dermoscopy also showed distinct pattern for AK and for BCC, but in 22% of them the data were not conclusive. Our study permits us to define two specific VTG patterns, BCC and AK respectively.

The role of ultrasound and ultrasound-guided fine needle aspiration biopsy of lymph nodes in patients with skin tumours.

BACKGROUND: The primary aim of this study was to evaluate the diagnostic accuracy of ultrasound (US) in the study of superficial lymph nodes during the follow-up of patients surgically treated for skin tumours. The secondary objective was to compare positive cytological results with histological reports. PATIENTS AND METHODS: From 2004 to 2011, 480 patients (male/female: 285/195; median age 57 years; prevalent skin tumour: melanoma) underwent US-guided fine-needle aspiration biopsy (FNAB) of suspicious recurrent lymph nodes. An expert radiologist first performed US testing of the lymph nodes, expressing either a negative or positive outcome of the test. Subsequently, US-guided FNAB was performed. FNAB positive patients were subjected to lymphadenectomy; the patients who tested negative underwent the follow-up. RESULTS: The size of lymph nodes was ≤ 2 cm in 90% of cases. Out of the 336 (70%) US "positive" patients, 231 (68.8%) were FNAB positives. Out of the 144 (30%) US "negatives", 132 (91.7%) were FNAB negatives. The sensitivity and specificity of the US were 95% and 55.7%, respectively; the negative predictive value was 91.7% and the positive predictive value was 68.8%. Definitive histological results confirmed FNAB positivity in 97.5% of lymphadenectomies. CONCLUSIONS: US is a sensitive method in the evaluation of superficial lymph nodes during the follow-up of patients with skin tumours. High positive predictive value of cytology was confirmed.

Metal-Halide Perovskite Submicrometer-Thick Films for Ultra-Stable Self-Powered Direct X-Ray Detectors.

Metal-halide perovskites are revolutionizing the world of X-ray detectors, due to the development of sensitive, fast, and cost-effective devices. Self-powered operation, ensuring portability and low power consumption, has also been recently demonstrated in both bulk materials and thin films. However, the signal stability and repeatability under continuous X-ray exposure has only been tested up to a few hours, often reporting degradation of the detection performance. Here it is shown that self-powered direct X-ray detectors, fabricated starting from a FAPbBr3 submicrometer-thick film deposition onto a mesoporous TiO2 scaffold, can withstand a 26-day uninterrupted X-ray exposure with negligible signal loss, demonstrating ultra-high operational stability and excellent repeatability. No structural modification is observed after irradiation with a total ionizing dose of almost 200 Gy, revealing an unexpectedly high radiation hardness for a metal-halide perovskite thin film. In addition, trap-assisted photoconductive gain enabled the device to achieve a record bulk sensitivity of 7.28 C Gy-1 cm-3 at 0 V, an unprecedented value in the field of thin-film-based photoconductors and photodiodes for "hard" X-rays. Finally, prototypal validation under the X-ray beam produced by a medical linear accelerator for cancer treatment is also introduced.

Flexible, Transparent, and Bifacial Perovskite Solar Cells and Modules Using the Wide-Band Gap FAPbBr3 Perovskite Absorber.

Perovskite solar cells (PSCs) offer impressive performance and flexibility, thanks to their simple, low-temperature deposition methods. Their band gap tunability allows for a wide range of applications, transitioning from opaque to transparent devices. This study introduces the first flexible, bifacial PSCs using the FAPbBr3 perovskite. We investigated the impact of optimizing electron and hole transport layers on the cells' bifaciality, transparency, and stability. PSCs achieved a maximum power conversion efficiency (PCE) of 6.8 and 18.7% under 1 sun and indoor light conditions (1200 lx), respectively, showing up to 98% bifaciality factor and an average visible transmittance (AVT) of 55%. Additionally, a P1-P2-P3 laser ablation scheme has been developed on the flexible poly(ethylene terephthalate) (PET) substrate for perovskite solar modules showing a PCE of 4.8% and high geometrical fill factor (97.8%). These findings highlight the potential of flexible, bifacial PSCs for diverse applications such as building-integrated photovoltaics (BIPV), agrivoltaics, automotive technology, wearable sensors, and Internet of things (IoT).