RESUMEN
Highly collimated and directional backlights are essential for realizing advanced display technologies such as autostereoscopic 3D displays. Previously reported collimated backlights, either edge-lit or direct-lit, in general still suffer unsatisfactory form factors, directivity, uniformity, or crosstalk etc. In this work, we report a simple stacking architecture for the highly collimated and uniform backlights, by combining linear light source arrays and carefully designed cylindrical lens arrays. Experiments were conducted to validate the design and simulation, using the conventional edge-lit backlight or the direct-lit mini-LED (mLED) arrays as light sources, the NiFe (stainless steel) barrier sheets, and cylindrical lens arrays fabricated by molding. Highly collimated backlights with small angular divergence of ±1.45°â¼±2.61°, decent uniformity of 93-96%, and minimal larger-angle sidelobes in emission patterns were achieved with controlled divergence of the light source and optimization of lens designs. The architecture reported here provides a convenient way to convert available backlight sources into a highly collimated backlight, and the use of optically reflective barrier also helps recycle light energy and enhance the luminance. The results of this work are believed to provide a facile approach for display technologies requiring highly collimated backlights.
RESUMEN
The objective of this study is to identify effective engineering methods for controlling handheld workpiece vibration during grinding processes. Prolonged and intensive exposures to such vibration can cause hand-arm vibration syndrome among workers performing workpiece grinding, but how to effectively control these exposures remains an important issue. This study developed a methodology for performing their analyses and evaluations based on a model of the entire grinding machine-workpiece-hand-arm system. The model can simulate the vibration responses of a workpiece held in the worker's hands and pressed against a grinding wheel in order to shape the workpiece in the major frequency range of concern (6.3-1600 Hz). The methodology was evaluated using available experimental data. The results suggest that the methodology is acceptable for these analyses and evaluations. The results also suggest that the workpiece vibration resulting from the machine vibration generally depends on two mechanisms or pathways: (1) the direct vibration transmission from the grinding machine; and (2) the indirect transmission that depends on both the machine vibration transmission to the workpiece and the interface excitation transformation to the workpiece vibration. The methodology was applied to explore and/or analyze various engineering methods for controlling workpiece vibrations. The modeling results suggest that while these intervention methods have different advantages and limitations, some of their combinations can effectively reduce the vibration exposures of grinding workers. These findings can be used as guidance for selecting and developing more effective technologies to control handheld workpiece vibration exposures.
RESUMEN
Using a 60-day pot culture experiment, we investigated the effect of selenium on phytoremediation of soil containing high-level diesel by Alternanthera philoxeroides (alligator weed). Diesel (20â¯gâ¯kg-1) decreased the growth of A. philoxeroides and induced oxidative stress, as indicated by tissue levels of hydrogen peroxide (H2O2) and malondialdehyde (MDA). Adding Se (0.5 or 1.5â¯mgâ¯kg-1) to diesel-treated soil alleviated oxidative stress and improved biomass production, and the low dose was as effective as the high dose. After 60 days, the reduction in rhizospheric soil diesel was 20.1⯱â¯0.55% without Se and 35.2⯱â¯3.6% with Se, showing a significant increase in efficiency. Again, the low Se dose was as effective as the high dose. These findings advance the field phytoremediation by demonstrating that Se, at 0.5â¯mgâ¯kg-1, enhances removal and increases plant tolerance to petroleum hydrocarbons.
Asunto(s)
Amaranthaceae/crecimiento & desarrollo , Restauración y Remediación Ambiental/métodos , Gasolina , Selenio/metabolismo , Contaminantes del Suelo/metabolismo , Biodegradación Ambiental , Selenio/administración & dosificaciónRESUMEN
The objective of this study was to develop a convenient and reliable adapter method for testing and evaluating vibration-reducing (VR) gloves and VR materials at the fingers. The general requirements and technical specifications for the design of the new adapter were based on our previous studies of hand-held adapters for vibration measurement and a conceptual model of the fingers-adapter-glove-handle system developed in this study. Two thicknesses (2 mm and 3 mm) of the adapter beam were fabricated using a 3-D printer. Each adapter is a thin beam equipped with a miniature tri-axial accelerometer (1.1 g) mounted at its center, with a total weight ≤ 2.2 g. To measure glove vibration transmissibility, the adapter is held with two gloved fingers; a finger is positioned on each side of the accelerometer. Each end of the adapter beam is slotted between the glove material and the finger. A series of experiments was conducted to evaluate this two-fingers-held adapter method by measuring the transmissibility of typical VR gloves and a sample VR material. The experimental results indicate that the major resonant frequency of the lightweight adapter on the VR material (≥800 Hz) is much higher than the resonant frequencies of the gloved fingers grasping a cylindrical handle (≤300 Hz). The experimental results were repeatable across the test treatments. The basic characteristics of the measured glove vibration transmissibility are consistent with the theoretical predictions based on the biodynamics of the gloved fingers-hand-arm system. The results suggest that VR glove fingers can effectively reduce only high-frequency vibration, and VR effectiveness can be increased by reducing the finger contact force. This study also demonstrated that the finger adapter method can be combined with the palm adapter method prescribed in the standardized glove test, which can double the test efficiency without substantially increasing the expense of the test.
RESUMEN
This study conducted two series of experiments to investigate the relationships between hand coupling force and biodynamic responses of the hand-arm system. In the first experiment, the vibration transmissibility on the system was measured as a continuous function of grip force while the hand was subjected to discrete sinusoidal excitations. In the second experiment, the biodynamic responses of the system subjected to a broadband random vibration were measured under five levels of grip forces and a combination of grip and push forces. This study found that the transmissibility at each given frequency increased with the increase in the grip force before reaching a maximum level. The transmissibility then tended to plateau or decrease when the grip force was further increased. This threshold force increased with an increase in the vibration frequency. These relationships remained the same for both types of vibrations. The implications of the experimental results are discussed. Practitioner Summary: Shocks and vibrations transmitted to the hand-arm system may cause injuries and disorders of the system. How to take hand coupling force into account in the risk assessment of vibration exposure remains an important issue for further studies. This study is designed and conducted to help resolve this issue.
Asunto(s)
Brazo/fisiología , Fuerza de la Mano/fisiología , Mano/fisiología , Vibración/efectos adversos , Trabajo/fisiología , Adolescente , Adulto , Fenómenos Biomecánicos , Humanos , Masculino , Exposición Profesional/efectos adversos , Adulto JovenRESUMEN
Some powered hand tools can generate significant vibration at frequencies below 25 Hz. It is not clear whether such vibration can be effectively transmitted to the upper arm, shoulder, neck, and head and cause adverse effects in these substructures. The objective of this study is to investigate the vibration transmission from the human hands to these substructures. Eight human subjects participated in the experiment, which was conducted on a 1-D vibration test system. Unlike many vibration transmission studies, both the right and left hand-arm systems were simultaneously exposed to the vibration to simulate a working posture in the experiment. A laser vibrometer and three accelerometers were used to measure the vibration transmitted to the substructures. The apparent mass at the palm of each hand was also measured to help in understanding the transmitted vibration and biodynamic response. This study found that the upper arm resonance frequency was 7-12 Hz, the shoulder resonance was 7-9 Hz, and the back and neck resonances were 6-7 Hz. The responses were affected by the hand-arm posture, applied hand force, and vibration magnitude. The transmissibility measured on the upper arm had a trend similar to that of the apparent mass measured at the palm in their major resonant frequency ranges. The implications of the results are discussed. RELEVANCE TO INDUSTRY: Musculoskeletal disorders (MSDs) of the shoulder and neck are important issues among many workers. Many of these workers use heavy-duty powered hand tools. The combined mechanical loads and vibration exposures are among the major factors contributing to the development of MSDs. The vibration characteristics of the body segments examined in this study can be used to help understand MSDs and to help develop more effective intervention methods.
RESUMEN
To control vibration-induced white finger among workers performing the fine grinding of golf club heads, the aims of this study are to clarify the major vibration sources in the grinding process, to identify and understand the basic characteristics of the club head vibration, and to propose potential approaches for reducing the vibration exposure. The vibrations on two typical club heads and two belt grinding machines were measured at a workplace. A simulated test station was also constructed and used to help examine some influencing factors of the club head vibration. This study found that the club head vibration was the combination of the vibration transmitted from the grinding machines and that generated in the grinding process. As a result, any factor that affects the machine vibration, the grinding vibration, and/or the dynamic response of the club head can influence the vibration exposure of the fingers or hands holding the club head in the grinding process. The significant influencing factors identified in the study include testing subject, grinding machine, machine operation speed, drive wheel condition, club head model, mechanical constraints imposed on the club head during the grinding, and machine foot pad. These findings suggest that the vibration exposure can be controlled by reducing the grinding machine vibration, changing the workpiece dynamic properties, and mitigating the vibration transmission in its pathway. Many potential methods for the control are proposed and discussed. RELEVANCE TO INDUSTRY: Vibrations on handheld workpieces can be effectively transmitted to the hands, especially the fingers. As a result, a major component of the hand-arm vibration syndrome - vibration-induced white finger - has been observed among some workers performing the grinding and/or polishing tasks of the handheld workpieces such as golf club heads. The results of this study can be used to develop more effective methods and technologies to control the vibration exposure of these workers. This may help effectively control this occupational disease.
RESUMEN
Palaeoxenus sinensis Chang, Muona & Teräväinen sp. nov. (Coleoptera, Eucnemidae) is described on the basis of a Cretaceous larva found from the Yixian Formation in Huangbanjigou, Liaoning Province, China. The only previously known member of this clade is a southern Californian endemic, Dohrn's elegant eucnemid beetle (Palaeoxenus dohrni), a species that develops in conifers, especially the incense cedar (Calocedrus decurrens). The new find proves that the highly specialized main eucnemid lineages had evolved 123 Mya, before the main radiation of the angiosperms and probably as an adaptation to development in gymnosperms.
RESUMEN
Mechanical arm systems are commonly used to support powered hand tools to alleviate ergonomic stressors related to the development of workplace musculoskeletal disorders. However, the use of these systems can increase exposure times to other potentially harmful agents such as hand-transmitted vibration. To examine how these tool support systems affect tool vibration, the primary objectives of this study were to characterize the vibration emissions of typical portable pneumatic grinders used for surface grinding with and without a mechanical arm support system at a workplace and to estimate the potential risk of the increased vibration exposure time afforded by the use of these mechanical arm systems. This study also developed a laboratory-based simulated grinding task based on the ISO 28927-1 (2009) standard for assessing grinder vibrations; the simulated grinding vibrations were compared with those measured during actual workplace grinder operations. The results of this study demonstrate that use of the mechanical arm may provide a health benefit by reducing the forces required to lift and maneuver the tools and by decreasing hand-transmitted vibration exposure. However, the arm does not substantially change the basic characteristics of grinder vibration spectra. The mechanical arm reduced the average frequency-weighted acceleration by about 24% in the workplace and by about 7% in the laboratory. Because use of the mechanical arm system can increase daily time-on-task by 50% or more, the use of such systems may actually increase daily time-weighted hand-transmitted vibration exposures in some cases. The laboratory acceleration measurements were substantially lower than the workplace measurements, and the laboratory tool rankings based on acceleration were considerably different than those from the workplace. Thus, it is doubtful that ISO 28927-1 is useful for estimating workplace grinder vibration exposures or for predicting workplace grinder acceleration rank orders.
Asunto(s)
Exposición Profesional , Medición de Riesgo/métodos , Vibración , Brazo , Trastornos de Traumas Acumulados/prevención & control , Mano/fisiología , Síndrome por Vibración de la Mano y el Brazo/prevención & control , Humanos , Vibración/efectos adversos , Lugar de TrabajoRESUMEN
Anyone seeking to control the risks from vibration transmitted to the hands and arms may contemplate the use of anti-vibration gloves. To make an informed decision about any type of personal protective equipment, it is necessary to have performance data that allow the degree of protection to be estimated. The information provided with an anti-vibration glove may not be easy to understand without some background knowledge of how gloves are tested and does not provide any clear route for estimating likely protection. Some of the factors that influence the potential efficacy of an anti-vibration glove include how risks from hand-arm vibration exposure are assessed, how the standard test for a glove is carried out, the frequency range and direction of the vibration for which protection is sought, how much hand contact force or pressure is applied and the physical limitations due to glove material and construction. This paper reviews some of the background issues that are useful for potential purchasers of anti-vibration gloves. Ultimately, anti-vibration gloves cannot be relied on to provide sufficient and consistent protection to the wearer and before their use is contemplated all other available means of vibration control ought first to be implemented.
RESUMEN
For exposure to hand-transmitted vibration (HTV), personal protective equipment is sold in the form of anti-vibration (AV) gloves, but it remains unclear how much these gloves actually reduce vibration exposure or prevent the development of hand-arm vibration syndrome in the workplace. This commentary describes some of the issues that surround the classification of AV gloves, the assessment of their effectiveness and their applicability in the workplace. The available information shows that AV gloves are unreliable as devices for controlling HTV exposures. Other means of vibration control, such as using alternative production techniques, low-vibration machinery, routine preventative maintenance regimes, and controlling exposure durations are far more likely to deliver effective vibration reductions and should be implemented. Furthermore, AV gloves may introduce some adverse effects such as increasing grip force and reducing manual dexterity. Therefore, one should balance the benefits of AV gloves and their potential adverse effects if their use is considered.
Asunto(s)
Guantes Protectores , Síndrome por Vibración de la Mano y el Brazo/prevención & control , Vibración/efectos adversos , Traumatismos del Brazo/etiología , Traumatismos del Brazo/prevención & control , Fenómenos Biomecánicos , Guantes Protectores/efectos adversos , Guantes Protectores/normas , Humanos , Modelos Teóricos , Exposición Profesional/prevención & controlRESUMEN
Sheet metal workers operating rivet bucking bars are at risk of developing hand and wrist musculoskeletal disorders associated with exposures to hand-transmitted vibrations and forceful exertions required to operate these hand tools. New bucking bar technologies have been introduced in efforts to reduce workplace vibration exposures to these workers. However, the efficacy of these new bucking bar designs has not been well documented. While there are standardized laboratory-based methodologies for assessing the vibration emissions of many types of powered hand tools, no such standard exists for rivet bucking bars. Therefore, this study included the development of a laboratory-based method for assessing bucking bar vibrations which utilizes a simulated riveting task. With this method, this study evaluated three traditional steel bucking bars, three similarly shaped tungsten alloy bars, and three bars featuring spring-dampeners. For comparison the bucking bar vibrations were also assessed during three typical riveting tasks at a large aircraft maintenance facility. The bucking bars were rank-ordered in terms of unweighted and frequency-weighted acceleration measured at the hand-tool interface. The results suggest that the developed laboratory method is a reasonable technique for ranking bucking bar vibration emissions; the lab-based riveting simulations produced similar rankings to the workplace rankings. However, the laboratory-based acceleration averages were considerably lower than the workplace measurements. These observations suggest that the laboratory test results are acceptable for comparing and screening bucking bars, but the laboratory measurements should not be directly used for assessing the risk of workplace bucking bar vibration exposures. The newer bucking bar technologies exhibited significantly reduced vibrations compared to the traditional steel bars. The results of this study, together with other information such as rivet quality, productivity, tool weight, comfort, worker acceptance, and initial cost can be used to make informed bucking bar selections.
Asunto(s)
Laboratorios , Exposición Profesional/análisis , Vibración , Lugar de Trabajo , Aeronaves , Industria de la Construcción/instrumentación , Mano , Síndrome por Vibración de la Mano y el Brazo/prevención & control , Humanos , Enfermedades Profesionales , Exposición Profesional/efectos adversos , Medición de Riesgo , Vibración/efectos adversosRESUMEN
BACKGROUND: Nonunions in the upper extremity are challenging for the reconstructive surgeon. The evolution of microsurgical techniques has allowed for the reliable use of free vascularized bone flaps. METHODS: In a retrospective study, patients with challenging upper limb nonunions who underwent free vascularized corticocancellous flaps from the medial femoral condyle (MFC) were included. Patient demographics, surgical technique, and outcomes were evaluated. RESULTS: Fifteen patients with nonunions of the upper extremity underwent free MFC corticocancellous flap reconstruction. The length of preoperative bone defects ranged from 0.8 to 3 cm, and the mean number of procedure prior to free MFC reconstruction was 1.5. Thirteen patients healed completely in an average of 15 weeks (range, 8-22 weeks). Two patients were lost to follow-up. Only one patient required additional surgery. Functional outcome measures such as Mayo, Disability of Arm, Shoulder, and Hand, and Constant-Murley scores all demonstrated improvement. CONCLUSION: The free vascularized MFC corticocancellous flap can be successfully used for challenging upper extremity nonunions and small bone defects.
Asunto(s)
Fracturas no Consolidadas/cirugía , Colgajos Tisulares Libres , Fracturas del Húmero/cirugía , Fracturas del Cúbito/cirugía , Extremidad Superior/lesiones , Adolescente , Adulto , Femenino , Falanges de los Dedos de la Mano/lesiones , Humanos , Masculino , Persona de Mediana Edad , Radio (Anatomía)/lesiones , Estudios Retrospectivos , Hueso Escafoides/lesiones , Recolección de Tejidos y Órganos , Resultado del Tratamiento , Adulto JovenRESUMEN
The objective of this study is to evaluate an adapter method for measuring the vibration on the human arms. Four instrumented adapters with different weights were used to measure the vibration transmitted to the wrist, forearm, and upper arm of each subject. Each adapter was attached at each location on the subjects using an elastic cloth wrap. Two laser vibrometers were also used to measure the transmitted vibration at each location to evaluate the validity of the adapter method. The apparent mass at the palm of the hand along the forearm direction was also measured to enhance the evaluation. This study found that the adapter and laser-measured transmissibility spectra were comparable with some systematic differences. While increasing the adapter mass reduced the resonant frequency at the measurement location, increasing the tightness of the adapter attachment increased the resonant frequency. However, the use of lightweight (≤15 g) adapters under medium attachment tightness did not change the basic trends of the transmissibility spectrum. The resonant features observed in the transmissibility spectra were also correlated with those observed in the apparent mass spectra. Because the local coordinate systems of the adapters may be significantly misaligned relative to the global coordinates of the vibration test systems, large errors were observed for the adapter-measured transmissibility in some individual orthogonal directions. This study, however, also demonstrated that the misalignment issue can be resolved by either using the total vibration transmissibility or by measuring the misalignment angles to correct the errors. Therefore, the adapter method is acceptable for understanding the basic characteristics of the vibration transmission in the human arms, and the adapter-measured data are acceptable for approximately modeling the system.
RESUMEN
The objective of this study is to enhance the understanding of the vibration transmission in the hand-arm system in three orthogonal directions (X, Y, and Z). For the first time, the transmitted vibrations distributed on the entire hand-arm system exposed in the three orthogonal directions via a 3-D vibration test system were measured using a 3-D laser vibrometer. Seven adult male subjects participated in the experiment. This study confirms that the vibration transmissibility generally decreased with the increase in distance from the hand and it varied with the vibration direction. Specifically, to the upper arm and shoulder, only moderate vibration transmission was measured in the test frequency range (16 to 500 Hz), and virtually no transmission was measured in the frequency range higher than 50 Hz. The resonance vibration on the forearm was primarily in the range of 16-30 Hz with the peak amplitude of approximately 1.5 times of the input vibration amplitude. The major resonance on the dorsal surfaces of the hand and wrist occurred at around 30-40 Hz and, in the Y direction, with peak amplitude of more than 2.5 times of the input amplitude. At higher than 50 Hz, vibration transmission was effectively limited to the hand and fingers. A major finger resonance was observed at around 100 Hz in the X and Y directions and around 200 Hz in the Z direction. In the fingers, the resonance magnitude in the Z direction was generally the lowest, and the resonance magnitude in the Y direction was generally the highest with the resonance amplitude of 3 times the input vibration, which was similar to the transmissibility at the wrist and hand dorsum. The implications of the results are discussed. RELEVANCE TO INDUSTRY: Prolonged, intensive exposure to hand-transmitted vibration could result in hand-arm vibration syndrome. While the syndrome's precise mechanisms remain unclear, the characterization of the vibration transmissibility of the system in the three orthogonal dimensions performed in this study can help understand the syndrome and help develop improved frequency weightings for assessing the risk of the exposure for developing various components of the syndrome.
RESUMEN
Vibration-reducing (VR) gloves have been used to reduce the hand-transmitted vibration exposures from machines and powered hand tools but their effectiveness remains unclear, especially for finger protection. The objectives of this study are to determine whether VR gloves can attenuate the vibration transmitted to the fingers and to enhance the understanding of the mechanisms of how these gloves work. Seven adult male subjects participated in the experiment. The fixed factors evaluated include hand force (four levels), glove condition (gel-filled, air bladder, no gloves), and location of the finger vibration measurement. A 3-D laser vibrometer was used to measure the vibrations on the fingers with and without wearing a glove on a 3-D hand-arm vibration test system. This study finds that the effect of VR gloves on the finger vibration depends on not only the gloves but also their influence on the distribution of the finger contact stiffness and the grip effort. As a result, the gloves increase the vibration in the fingertip area but marginally reduce the vibration in the proximal area at some frequencies below 100 Hz. On average, the gloves reduce the vibration of the entire fingers by less than 3% at frequencies below 80 Hz but increase at frequencies from 80 to 400 Hz. At higher frequencies, the gel-filled glove is more effective at reducing the finger vibration than the air bladder-filled glove. The implications of these findings are discussed. RELEVANCE TO INDUSTRY: Prolonged, intensive exposure to hand-transmitted vibration can cause hand-arm vibration syndrome. Vibration-reducing gloves have been used as an alternative approach to reduce the vibration exposure. However, their effectiveness for reducing finger-transmitted vibrations remains unclear. This study enhanced the understanding of the glove effects on finger vibration and provided useful information on the effectiveness of typical VR gloves at reducing the vibration transmitted to the fingers. The new results and knowledge can be used to help select appropriate gloves for the operations of powered hand tools, to help perform risk assessment of the vibration exposure, and to help design better VR gloves.
RESUMEN
Vibration-reducing (VR) gloves have been increasingly used to help reduce vibration exposure, but it remains unclear how effective these gloves are. The purpose of this study was to estimate tool-specific performances of VR gloves for reducing the vibrations transmitted to the palm of the hand in three orthogonal directions (3-D) in an attempt to assess glove effectiveness and aid in the appropriate selection of these gloves. Four typical VR gloves were considered in this study, two of which can be classified as anti-vibration (AV) gloves according to the current AV glove test standard. The average transmissibility spectrum of each glove in each direction was synthesized based on spectra measured in this study and other spectra collected from reported studies. More than seventy vibration spectra of various tools or machines were considered in the estimations, which were also measured in this study or collected from reported studies. The glove performance assessments were based on the percent reduction of frequency-weighted acceleration as is required in the current standard for assessing the risk of vibration exposures. The estimated tool-specific vibration reductions of the gloves indicate that the VR gloves could slightly reduce (<5%) or marginally amplify (<10%) the vibrations generated from low-frequency (<25 Hz) tools or those vibrating primarily along the axis of the tool handle. With other tools, the VR gloves could reduce palm-transmitted vibrations in the range of 5%-58%, primarily depending on the specific tool and its vibration spectra in the three directions. The two AV gloves were not more effective than the other gloves with some of the tools considered in this study. The implications of the results are discussed. RELEVANCE TO INDUSTRY: Hand-transmitted vibration exposure may cause hand-arm vibration syndrome. Vibration-reducing gloves are considered as an alternative approach to reduce the vibration exposure. This study provides useful information on the effectiveness of the gloves when used with many tools for reducing the vibration transmitted to the palm in three directions. The results can aid in the appropriate selection and use of these gloves.
RESUMEN
BACKGROUND: Cockroaches are widely acknowledged as significant vectors of pathogenic microorganisms. The Periplaneta fuliginosa densovirus (PfDNV) infects the smoky-brown cockroach P. fuliginosa and causes host mortality, which identifies the PfDNV as a species-specific and environmentally friendly biopesticide. However, although the biochemical characterization of PfDNV has been extensively studied, the immune response against PfDNV remains largely unclear. RESULTS: Here, we investigated the replication of PfDNV and its associated pathological phenotype in the foregut and hindgut. Consequently, we dissected and performed transcriptome sequencing on the foregut, midgut, and hindgut separately. We revealed the up-regulation of immune response signaling pathway c-Jun N-terminal kinase (JNK) and apoptosis in response to viral infection. Furthermore, knockdown of the JNK upstream gene Ben resulted in a decrease in virus titer and delayed host mortality. CONCLUSION: Taken together, our findings provide evidence that the Ben-JNK signaling plays a crucial role in PfDNV infection, leading to excessive apoptosis in intestinal tissues and ultimately resulting in the death of the host. Our results indicated that the host response to PfDNV fosters viral infection, thereby increasing host lethality. This underscores the potential of PfDNV as a viable, environmentally friendly biopesticide. © 2024 Society of Chemical Industry.
Asunto(s)
Densovirus , Periplaneta , Animales , Periplaneta/virología , Periplaneta/fisiología , Periplaneta/genética , Densovirus/fisiología , Densovirus/genética , Proteínas de Insectos/metabolismo , Proteínas de Insectos/genética , Sistema de Señalización de MAP Quinasas , Apoptosis , Transducción de SeñalRESUMEN
UNLABELLED: Motorized vibrating manure forks were used in beach-cleaning operations following the massive Deepwater Horizon oil spill in the Gulf of Mexico during the summer of 2010. OBJECTIVES: The objectives of this study were to characterize the vibration emissions of these motorized forks and to provide a first approximation of hand-transmitted vibration exposures to workers using these forks for beach cleaning. METHODS: Eight operators were recruited to operate the motorized forks during this laboratory study. Four fork configurations were used in the study; two motor speeds and two fork basket options were evaluated. Accelerations were measured near each hand as the operators completed the simulated beach-cleaning task. RESULTS: The dominant vibration frequency for these tools was identified to be around 20 Hz. Because acceleration was found to increase with motor speed, workers should consider operating these tools with just enough speed to get the job done. These forks exhibited considerable acceleration magnitudes when unloaded. CONCLUSIONS: The study results suggest that the motor should not be operated with the fork in the unloaded state. Anti-vibration gloves are not effective at attenuating the vibration frequencies produced by these forks, and they may even amplify the transmitted vibration and increase hand/arm fatigue. While regular work gloves are suitable, vibration-reducing gloves may not be appropriate for use with these tools. These considerations may also be generally applicable for the use of motorized forks in other workplace environments.
Asunto(s)
Agricultura/instrumentación , Exposición Profesional/análisis , Vibración/efectos adversos , Adulto , Femenino , Guantes Protectores/normas , Guantes Protectores/estadística & datos numéricos , Mano , Síndrome por Vibración de la Mano y el Brazo/prevención & control , Humanos , Masculino , México/epidemiología , Sistema Musculoesquelético/lesiones , Exposición Profesional/efectos adversos , Contaminación por Petróleo/efectos adversos , Medición de Riesgo/métodos , Adulto JovenRESUMEN
Vibration-reducing (VR) gloves are commonly used as a means to help control exposures to hand-transmitted vibrations generated by powered hand tools. The objective of this study was to characterise the vibration transmissibility spectra and frequency-weighted vibration transmissibility of VR gloves at the palm of the hand in three orthogonal directions. Seven adult males participated in the evaluation of seven glove models using a three-dimensional hand-arm vibration test system. Three levels of hand coupling force were applied in the experiment. This study found that, in general, VR gloves are most effective at reducing vibrations transmitted to the palm along the forearm direction. Gloves that are found to be superior at reducing vibrations in the forearm direction may not be more effective in the other directions when compared with other VR gloves. This casts doubts on the validity of the standardised glove screening test. Practitioner Summary: This study used human subjects to measure three-dimensional vibration transmissibility of vibration-reducing gloves at the palm and identified their vibration attenuation characteristics. This study found the gloves to be most effective at reducing vibrations along the forearm direction. These gloves did not effectively attenuate vibration along the handle axial direction.