High-Performance Hard X-Ray Imaging Detector Using Facet-Dependent Bismuth Vanadate.

Bismuth vanadate (BiVO4) exhibits large absorption efficiency for hard X-rays, which endows it with a robust capacity to attenuate X-ray radiation across a broad energy range. The anisotropic properties of BiVO4 allow for the manipulation of their physical and chemical characteristics through crystallographic orientation and exposed facets. In this study, the issue of heavy recombination caused by sluggish electron transport in BiVO4 is successfully addressed by enhancing the abundance of the (040) crystal face ratio using a Co2+ crystal face exposure agent. The facet-dependent modifications exhibit excellent and balanced intrinsic charge transport properties, and finely optimize both the sensitivity and detection limit of BiVO4 X-ray detectors. As a result, ultra-stable BiVO4 metal oxide X-ray detectors demonstrate a high sensitivity of 3164 µC Gyair -1 cm-2 and a low detection limit of 20.76 nGyair s-1 under 110 kVp hard X-rays, establishing a new benchmark for X-ray detectors based on polycrystalline Bi-halides and metal oxides. These findings highlight the significance of crystal orientation in optimizing materials for X-ray detection, setting a new sensitivity record for X-ray detectors based on polycrystalline Bi-halides and metal oxides, which paves the way for the development of advanced, low-dose, and highly stable imaging systems specifically for hard X-rays.

A regulation strategy of self-assembly molecules for achieving efficient inverted perovskite solar cells.

Self-assembled monolayers (SAMs) have been successfully employed to enhance the efficiency of inverted perovskite solar cells (PSCs) and perovskite/silicon tandem solar cells due to their facile low-temperature processing and superior device performance. Nevertheless, depositing uniform and dense SAMs with high surface coverage on metal oxide substrates remains a critical challenge. In this work, we propose a holistic strategy to construct composite hole transport layers (HTLs) by co-adsorbing mixed SAMs (MeO-2PACz and 2PACz) onto the surface of the H2O2-modified NiOx layer. The results demonstrate that the conductivity of the NiOx bulk phase is enhanced due to the H2O2 modification, thereby facilitating carrier transport. Furthermore, the hydroxyl-rich NiOx surface promotes uniform and dense adsorption of mixed SAM molecules while enhancing their anchoring stability. In addition, the energy level alignment at the interface is improved due to the utilization of mixed SAMs in an optimized ratio. Furthermore, the perovskite film crystal growth is facilitated by the uniform and dense composite HTLs. As a result, the power conversion efficiency of PSCs based on composite HTLs is boosted from 22.26% to 23.16%, along with enhanced operational stability. This work highlights the importance of designing and constructing NiOx/SAM composite HTLs as an effective strategy for enhancing both the performance and stability of inverted PSCs.

Universal Image Restoration with Text Prompt Diffusion.

Universal image restoration (UIR) aims to accurately restore images with a variety of unknown degradation types and levels. Existing methods, including both learning-based and prior-based approaches, heavily rely on low-quality image features. However, it is challenging to extract degradation information from diverse low-quality images, which limits model performance. Furthermore, UIR necessitates the recovery of images with diverse and complex types of degradation. Inaccurate estimations further decrease restoration performance, resulting in suboptimal recovery outcomes. To enhance UIR performance, a viable approach is to introduce additional priors. The current UIR methods have problems such as poor enhancement effect and low universality. To address this issue, we propose an effective framework based on a diffusion model (DM) for universal image restoration, dubbed ETDiffIR. Inspired by the remarkable performance of text prompts in the field of image generation, we employ text prompts to improve the restoration of degraded images. This framework utilizes a text prompt corresponding to the low-quality image to assist the diffusion model in restoring the image. Specifically, a novel text-image fusion block is proposed by combining the CLIP text encoder and the DA-CLIP image controller, which integrates text prompt encoding and degradation type encoding into time step encoding. Moreover, to reduce the computational cost of the denoising UNet in the diffusion model, we develop an efficient restoration U-shaped network (ERUNet) to achieve favorable noise prediction performance via depthwise convolution and pointwise convolution. We evaluate the proposed method on image dehazing, deraining, and denoising tasks. The experimental results indicate the superiority of our proposed algorithm.

High-Performance Flat-Panel Perovskite X-ray Detectors Enabled by Defect Passivation in Ruddlesden-Popper Perovskites.

Halide perovskites have emerged as promising candidates in X-ray detection due to their strong X-ray absorption and excellent optoelectronic properties. The development of sensitive and stable flat-panel X-ray detectors with high resolution is crucial for practical applications. In this paper, we introduce a novel flat-panel X-ray detector that integrates quasi-two-dimensional (2D) Ruddlesden-Popper (RP) perovskite with a pixeled thin film transistor (TFT) backplane. We incorporate 2,5-dibromopyrimidine (DBPM) as an additive to passivate the Lewis acid defects in the quasi-2D RP perovskite. This modification results in suppressed ion migration, improved optoelectronic performance, and enhanced operational stability of the device. Impressively, the activation energy of the RP perovskite increases from 0.96 to 1.35 eV with the DBPM additive. As a result, X-ray detectors exhibit a high sensitivity of ∼13,600 µC Gyair-1 cm-2, a low detection limit of 6.56 nGyair s-1, and excellent operational stability. Moreover, the flat-panel detectors demonstrate a high spatial resolution of 3.7 line pairs per millimeter and excellent X-ray imaging properties under a remarkably low X-ray dose of ∼50 µGyair, which is just half of the X-ray dose typically used in commercial equipment. This study opens new avenues for the development of flat-panel perovskite X-ray detectors with significant potential for various applications.

Bottom-up construction of low-dimensional perovskite thick films for high-performance X-ray detection and imaging.

Quasi-two-dimensional (Q-2D) perovskite exhibits exceptional photoelectric properties and demonstrates reduced ion migration compared to 3D perovskite, making it a promising material for the fabrication of highly sensitive and stable X-ray detectors. However, achieving high-quality perovskite films with sufficient thickness for efficient X-ray absorption remains challenging. Herein, we present a novel approach to regulate the growth of Q-2D perovskite crystals in a mixed atmosphere comprising methylamine (CH3NH2, MA) and ammonia (NH3), resulting in the successful fabrication of high-quality films with a thickness of hundreds of micrometers. Subsequently, we build a heterojunction X-ray detector by incorporating the perovskite layer with titanium dioxide (TiO2). The precise regulation of perovskite crystal growth and the meticulous design of the device structure synergistically enhance the resistivity and carrier transport properties of the X-ray detector, resulting in an ultrahigh sensitivity (29721.4 µC Gyair-1 cm-2) for low-dimensional perovskite X-ray detectors and a low detection limit of 20.9 nGyair s-1. We have further demonstrated a flat panel X-ray imager (FPXI) showing a high spatial resolution of 3.6 lp mm-1 and outstanding X-ray imaging capability under low X-ray doses. This work presents an effective methodology for achieving high-performance Q-2D perovskite FPXIs that holds great promise for various applications in imaging technology.

Simultaneous achievement of defect passivation and carrier transport promotion by using emerald salt for methylammonium-free perovskite solar cells.

Defect passivation along with promoted charge transport is potentially an effective but seldom exploited strategy for high-performance perovskite solar cells (PSCs). Herein, the in situ defect passivation and carrier transport improvement are simultaneously realized by introducing a conductive polymer (i.e., emerald salt, ES) into the precursor solution of methylammonium (MA)-free perovskites. The interaction between ES and uncoordinated Pb2+ reduces defect density to suppress the non-radiative recombination. Moreover, ES can act as a "carrier driver" to promote the carrier transport due to its conductive feature, resulting in efficient PSC devices with a decent power conversion efficiency (PCE) of 23.0%, which is among the most efficient MA-free PSCs. The ES-based unencapsulated devices show superior stability, retaining 89.1% and 83.8% of their initial PCEs when subjected to 35 ± 5% relative humidity (RH) storage and 85 °C thermal aging for 1000 h, respectively. To further assess the large-area compatibility of our strategy, 5 × 5 cm2 mini modules were also fabricated, delivering an impressive efficiency of 19.3%. This work sheds light on the importance of conductive additives in boosting cell performance by playing multiple roles in passivating defects, retarding the moisture invasion, and enhancing and balancing charge transport.

A-Site Cation Engineering of Ruddlesden-Popper Perovskites for Stable, Sensitive, and Portable Direct Conversion X-ray Imaging Detectors.

Perovskite flat-panel X-ray detectors are promising products for realizing low-dose medical imaging, a nondestructive test, and security inspection. However, the perovskite X-ray imager still faces intractable problems such as severe baseline drift, a low signal-to-noise ratio, and rapid performance degradation, which were involved by the notorious intrinsic ion migration of the perovskite functional layer. In this work, sensitive, stable, and portable pixel quasi-two-dimensional (2D) Ruddlesden-Popper (RP) perovskite X-ray imagers were obtained by an advanced solvent-free laminated fabrication approach. A-Site cation engineering of RP perovskites provides a hint for solving the trade-off between stability and detection performance, resulting in a stable pixel X-ray imager that shows a sensitivity of ∼7000 µC Gyair-1 cm-2, a detection limit of 7.8 nGyair s-1, and good 2D multipixel X-ray imaging. This work demonstrates both a high-performance, stable X-ray imager and its robust fabrication, paving the way for adopting a RP perovskite imager as novel flat-panel X-ray detectors.